diff mbox series

[v2,7/7] ARM: dts: qcom: msm8226: Add mdss nodes

Message ID 20230308-msm8226-mdp-v2-7-e005b769ee28@z3ntu.xyz (mailing list archive)
State Superseded
Headers show
Series Display support for MSM8226 | expand

Commit Message

Luca Weiss May 30, 2023, 6:24 p.m. UTC
Add the nodes that describe the mdss so that display can work on
MSM8226.

Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
 arch/arm/boot/dts/qcom-msm8226.dtsi | 127 ++++++++++++++++++++++++++++++++++++
 1 file changed, 127 insertions(+)

Comments

Stephan Gerhold May 30, 2023, 7:12 p.m. UTC | #1
On Tue, May 30, 2023 at 08:24:17PM +0200, Luca Weiss wrote:
> Add the nodes that describe the mdss so that display can work on
> MSM8226.
> 
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>

Can you update this to use labels like in [1]? See inline below.
This will allow proper grouping of the labels in the board DT.

Thanks,
Stephan

[1]: https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux.git/commit/?h=for-next&id=835f939501769253eb7eb2dc5389b8592a63a3ed

> ---
>  arch/arm/boot/dts/qcom-msm8226.dtsi | 127 ++++++++++++++++++++++++++++++++++++
>  1 file changed, 127 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
> index 42acb9ddb8cc..c794f5ece1d1 100644
> --- a/arch/arm/boot/dts/qcom-msm8226.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
> @@ -636,6 +636,133 @@ smd-edge {
>  				label = "lpass";
>  			};
>  		};
> +
> +		mdss: display-subsystem@fd900000 {
> +			compatible = "qcom,mdss";
> +			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
> +			reg-names = "mdss_phys", "vbif_phys";
> +
> +			power-domains = <&mmcc MDSS_GDSC>;
> +
> +			clocks = <&mmcc MDSS_AHB_CLK>,
> +				 <&mmcc MDSS_AXI_CLK>,
> +				 <&mmcc MDSS_VSYNC_CLK>;
> +			clock-names = "iface",
> +				      "bus",
> +				      "vsync";
> +
> +			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <1>;
> +
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			status = "disabled";
> +
> +			mdp: display-controller@fd900000 {

			mdss_mdp:

> +				compatible = "qcom,msm8226-mdp5", "qcom,mdp5";
> +				reg = <0xfd900100 0x22000>;
> +				reg-names = "mdp_phys";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <0>;
> +
> +				clocks = <&mmcc MDSS_AHB_CLK>,
> +					 <&mmcc MDSS_AXI_CLK>,
> +					 <&mmcc MDSS_MDP_CLK>,
> +					 <&mmcc MDSS_VSYNC_CLK>;
> +				clock-names = "iface",
> +					      "bus",
> +					      "core",
> +					      "vsync";
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						mdp5_intf1_out: endpoint {

						mdss_mdp_intf1_out:

> +							remote-endpoint = <&dsi0_in>;
> +						};
> +					};
> +				};
> +			};
> +
> +			dsi0: dsi@fd922800 {

			mdss_dsi0:

> +				compatible = "qcom,msm8226-dsi-ctrl",
> +					     "qcom,mdss-dsi-ctrl";
> +				reg = <0xfd922800 0x1f8>;
> +				reg-names = "dsi_ctrl";
> +
> +				interrupt-parent = <&mdss>;
> +				interrupts = <4>;
> +
> +				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
> +						  <&mmcc PCLK0_CLK_SRC>;
> +				assigned-clock-parents = <&dsi_phy0 0>,
> +							 <&dsi_phy0 1>;
> +
> +				clocks = <&mmcc MDSS_MDP_CLK>,
> +					 <&mmcc MDSS_AHB_CLK>,
> +					 <&mmcc MDSS_AXI_CLK>,
> +					 <&mmcc MDSS_BYTE0_CLK>,
> +					 <&mmcc MDSS_PCLK0_CLK>,
> +					 <&mmcc MDSS_ESC0_CLK>,
> +					 <&mmcc MMSS_MISC_AHB_CLK>;
> +				clock-names = "mdp_core",
> +					      "iface",
> +					      "bus",
> +					      "byte",
> +					      "pixel",
> +					      "core",
> +					      "core_mmss";
> +
> +				phys = <&dsi_phy0>;
> +
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port@0 {
> +						reg = <0>;
> +						dsi0_in: endpoint {

						mdss_dsi0_in:

> +							remote-endpoint = <&mdp5_intf1_out>;
> +						};
> +					};
> +
> +					port@1 {
> +						reg = <1>;
> +						dsi0_out: endpoint {

						mdss_dsi0_out:

> +						};
> +					};
> +				};
> +			};
> +
> +			dsi_phy0: phy@fd922a00 {

			mdss_dsi0_phy:

> +				compatible = "qcom,dsi-phy-28nm-8226";
> +				reg = <0xfd922a00 0xd4>,
> +				      <0xfd922b00 0x280>,
> +				      <0xfd922d80 0x30>;
> +				reg-names = "dsi_pll",
> +					    "dsi_phy",
> +					    "dsi_phy_regulator";
> +
> +				#clock-cells = <1>;
> +				#phy-cells = <0>;
> +
> +				clocks = <&mmcc MDSS_AHB_CLK>,
> +					 <&rpmcc RPM_SMD_XO_CLK_SRC>;
> +				clock-names = "iface",
> +					      "ref";
> +			};
> +		};
>  	};
>  
>  	timer {
> 
> -- 
> 2.40.1
>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
index 42acb9ddb8cc..c794f5ece1d1 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -636,6 +636,133 @@  smd-edge {
 				label = "lpass";
 			};
 		};
+
+		mdss: display-subsystem@fd900000 {
+			compatible = "qcom,mdss";
+			reg = <0xfd900000 0x100>, <0xfd924000 0x1000>;
+			reg-names = "mdss_phys", "vbif_phys";
+
+			power-domains = <&mmcc MDSS_GDSC>;
+
+			clocks = <&mmcc MDSS_AHB_CLK>,
+				 <&mmcc MDSS_AXI_CLK>,
+				 <&mmcc MDSS_VSYNC_CLK>;
+			clock-names = "iface",
+				      "bus",
+				      "vsync";
+
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+			interrupt-controller;
+			#interrupt-cells = <1>;
+
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			status = "disabled";
+
+			mdp: display-controller@fd900000 {
+				compatible = "qcom,msm8226-mdp5", "qcom,mdp5";
+				reg = <0xfd900100 0x22000>;
+				reg-names = "mdp_phys";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_VSYNC_CLK>;
+				clock-names = "iface",
+					      "bus",
+					      "core",
+					      "vsync";
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						mdp5_intf1_out: endpoint {
+							remote-endpoint = <&dsi0_in>;
+						};
+					};
+				};
+			};
+
+			dsi0: dsi@fd922800 {
+				compatible = "qcom,msm8226-dsi-ctrl",
+					     "qcom,mdss-dsi-ctrl";
+				reg = <0xfd922800 0x1f8>;
+				reg-names = "dsi_ctrl";
+
+				interrupt-parent = <&mdss>;
+				interrupts = <4>;
+
+				assigned-clocks = <&mmcc BYTE0_CLK_SRC>,
+						  <&mmcc PCLK0_CLK_SRC>;
+				assigned-clock-parents = <&dsi_phy0 0>,
+							 <&dsi_phy0 1>;
+
+				clocks = <&mmcc MDSS_MDP_CLK>,
+					 <&mmcc MDSS_AHB_CLK>,
+					 <&mmcc MDSS_AXI_CLK>,
+					 <&mmcc MDSS_BYTE0_CLK>,
+					 <&mmcc MDSS_PCLK0_CLK>,
+					 <&mmcc MDSS_ESC0_CLK>,
+					 <&mmcc MMSS_MISC_AHB_CLK>;
+				clock-names = "mdp_core",
+					      "iface",
+					      "bus",
+					      "byte",
+					      "pixel",
+					      "core",
+					      "core_mmss";
+
+				phys = <&dsi_phy0>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port@0 {
+						reg = <0>;
+						dsi0_in: endpoint {
+							remote-endpoint = <&mdp5_intf1_out>;
+						};
+					};
+
+					port@1 {
+						reg = <1>;
+						dsi0_out: endpoint {
+						};
+					};
+				};
+			};
+
+			dsi_phy0: phy@fd922a00 {
+				compatible = "qcom,dsi-phy-28nm-8226";
+				reg = <0xfd922a00 0xd4>,
+				      <0xfd922b00 0x280>,
+				      <0xfd922d80 0x30>;
+				reg-names = "dsi_pll",
+					    "dsi_phy",
+					    "dsi_phy_regulator";
+
+				#clock-cells = <1>;
+				#phy-cells = <0>;
+
+				clocks = <&mmcc MDSS_AHB_CLK>,
+					 <&rpmcc RPM_SMD_XO_CLK_SRC>;
+				clock-names = "iface",
+					      "ref";
+			};
+		};
 	};
 
 	timer {