diff mbox series

[v5,7/9] arm64: dts: qcom: sa8775p: add high-speed UART nodes

Message ID 20230309103752.173541-8-brgl@bgdev.pl (mailing list archive)
State Accepted
Commit 41ae5ca448c21a82a2f07e10954b043a0d45a811
Headers show
Series arm64: dts: qcom: sa8775p-ride: enable relevant QUPv3 IPs | expand

Commit Message

Bartosz Golaszewski March 9, 2023, 10:37 a.m. UTC 
From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

Add two UART nodes that are known to be used by existing development
boards with this SoC.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sa8775p.dtsi | 30 +++++++++++++++++++++++++++
 1 file changed, 30 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
index d1b2a6d30eae..468390edf049 100644
--- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi
+++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi
@@ -490,6 +490,21 @@  &clk_virt SLAVE_QUP_CORE_1 0>,
 				operating-points-v2 = <&qup_opp_table_100mhz>;
 				status = "disabled";
 			};
+
+			uart12: serial@a94000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x00a94000 0x0 0x4000>;
+				interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP1_S5_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_1 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_1 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
 		};
 
 		qupv3_id_2: geniqup@8c0000 {
@@ -525,6 +540,21 @@  &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>,
 				status = "disabled";
 			};
 
+			uart17: serial@88c000 {
+				compatible = "qcom,geni-uart";
+				reg = <0x0 0x0088c000 0x0 0x4000>;
+				interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+				clock-names = "se";
+				interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+						 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+						<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+						 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ALWAYS>;
+				interconnect-names = "qup-core", "qup-config";
+				power-domains = <&rpmhpd SA8775P_CX>;
+				status = "disabled";
+			};
+
 			i2c18: i2c@890000 {
 				compatible = "qcom,geni-i2c";
 				reg = <0x0 0x00890000 0x0 0x4000>;