| Message ID | 20230314064322.65429-2-nikita@trvn.ru (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | [1/2] dt-bindings: arm: qcom: Add Acer Aspire 1 | expand |
On 14/03/2023 07:43, Nikita Travkin wrote: > Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform. > > The laptop design is similar to trogdor in the choice of primary > components but the specifics on usage of those differ slightly. > > Add the devicetree for the laptop with support for most of the > hardware present. > Thank you for your patch. There is something to discuss/improve. > +/ { > + model = "Acer Aspire 1"; > + compatible = "acer,aspire1", "qcom,sc7180"; > + chassis-type = "laptop"; > + > + reserved-memory { Wrong ordering. Top-level nodes go alphanumeric. > + zap_mem: zap-shader@80840000 { > + reg = <0 0x80840000 0 0x2000>; > + no-map; > + }; > + > + venus_mem: venus@85b00000 { > + reg = <0 0x85b00000 0 0x500000>; > + no-map; > + }; > + > + mpss_mem: mpss@86000000 { > + reg = <0x0 0x86000000 0x0 0x2000000>; > + no-map; > + }; > + > + adsp_mem: adsp@8e400000 { > + reg = <0x0 0x8e400000 0x0 0x2800000>; > + no-map; > + }; > + > + wlan_mem: wlan@93900000 { > + reg = <0x0 0x93900000 0x0 0x200000>; > + no-map; > + }; > + }; > + > + aliases { > + bluetooth0 = &bluetooth; > + hsuart0 = &uart3; > + serial0 = &uart8; > + wifi0 = &wifi; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + max98357a: audio-codec-0 { Do you have second audio-codec? If not, drop -0. > + compatible = "maxim,max98357a"; > + sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&_sd_mode_default>; > + pinctrl-names = "default"; > + > + #sound-dai-cells = <0>; > + }; > + > + backlight: backlight { > + compatible = "pwm-backlight"; > + pwms = <&sn65dsi86_bridge 1000000>; > + enable-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; > + > + pinctrl-0 = <&soc_bkoff_default>; > + pinctrl-names = "default"; > + }; > + > + reg_brij_1p2: bridge-1p2-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "brij_1p2"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + > + gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + pinctrl-0 = <®_edp_1p2_en_default>; > + pinctrl-names = "default"; > + }; > + > + reg_brij_1p8: bridge-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "brij_1p8"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + > + vin-supply = <&vreg_l8c_1p8>; > + > + gpio = <&tlmm 20 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + pinctrl-0 = <®_edp_1p8_en_default>; > + pinctrl-names = "default"; > + }; > + > + reg_codec_3p3: codec-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "codec_3p3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + pinctrl-0 = <®_audio_en_default>; > + pinctrl-names = "default"; > + }; > + > + reg_lcm_3p3: panel-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "lcm_3p3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + /* * Comment starts here > + /* HACK: Display fails with > + * > + * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz > + * *ERROR* Link training failed, link is off (-5) > + * > + * if the power to the panel was ever cut > + */ > +}; > + > +&camcc { status = "disabled"; }; Don't wrap nodes. > + > +&dsi0 { > + vdda-supply = <&vreg_l3c_1p2>; > + status = "okay"; > +}; > + > +&dsi0_out { > + remote-endpoint = <&sn65dsi86_in>; > + data-lanes = <0 1 2 3>; > +}; > + > +&dsi_phy { > + vdds-supply = <&vreg_l4a_0p8>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + status = "okay"; > + > + /* embedded-controller@76 */ > +}; > + > +&i2c4 { > + clock-frequency = <400000>; > + status = "okay"; > + > + /* > + * NOTE: DSDT defines two possible touchpads, other one is > + * > + * reg = <0x15>; > + * hid-descr-addr = <0x1>; > + */ > + > + touchpad@2c { > + compatible = "hid-over-i2c"; > + reg = <0x2c>; > + hid-descr-addr = <0x20>; > + > + vdd-supply = <®_tp_3p3>; > + > + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-0 = <&hid_touchpad_default>; > + pinctrl-names = "default"; > + }; > + > + keyboard@3a { > + compatible = "hid-over-i2c"; > + reg = <0x3a>; > + hid-descr-addr = <0x1>; > + > + interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-0 = <&hid_keyboard_default>; > + pinctrl-names = "default"; > + > + wakeup-source; > + }; > +}; > + > +&i2c9 { > + clock-frequency = <400000>; > + status = "okay"; > + > + alc5682: codec@1a { > + compatible = "realtek,rt5682i"; > + reg = <0x1a>; > + > + #sound-dai-cells = <1>; > + > + interrupt-parent = <&tlmm>; > + /* > + * This will get ignored because the interrupt type > + * is set in rt5682.c. Don't add Linux driver stuff to DTS. Not relevant, so drop the comment. > + */ > + interrupts = <28 IRQ_TYPE_EDGE_BOTH>; > + > + pinctrl-0 = <&codec_irq_default>; > + pinctrl-names = "default"; > + > + AVDD-supply = <&vreg_l15a_1p8>; > + MICVDD-supply = <®_codec_3p3>; > + VBAT-supply = <®_codec_3p3>; > + > + realtek,dmic1-data-pin = <1>; > + realtek,dmic1-clk-pin = <1>; > + realtek,jd-src = <1>; > + }; > +}; > + > +&i2c10 { > + clock-frequency = <400000>; > + status = "okay"; > + > + sn65dsi86_bridge: bridge@2c { > + compatible = "ti,sn65dsi86"; > + reg = <0x2c>; > + gpio-controller; > + #gpio-cells = <2>; > + #pwm-cells = <1>; > + > + interrupt-parent = <&tlmm>; > + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; > + > + enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; > + suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; > + > + pinctrl-0 = <&bridge_en_default>, > + <&edp_bridge_irq_default>, > + <&bridge_suspend_default>; Align entries. > + pinctrl-names = "default"; > + > + vpll-supply = <®_brij_1p8>; > + vccio-supply = <®_brij_1p8>; > + vcca-supply = <®_brij_1p2>; > + vcc-supply = <®_brij_1p2>; > + > + clocks = <&rpmhcc RPMH_LN_BB_CLK3>; > + clock-names = "refclk"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + sn65dsi86_in: endpoint { > + remote-endpoint = <&dsi0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + sn65dsi86_out: endpoint { > + data-lanes = <0 1>; > + remote-endpoint = <&panel_in_edp>; > + }; > + }; > + }; > + > + aux-bus { > + panel: panel { > + compatible = "edp-panel"; > + power-supply = <®_lcm_3p3>; > + backlight = <&backlight>; > + > + port { > + panel_in_edp: endpoint { > + remote-endpoint = <&sn65dsi86_out>; > + }; > + }; > + }; > + }; > + }; > +}; > + > +&gpu { > + status = "okay"; > + > + zap-shader { > + memory-region = <&zap_mem>; > + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn"; > + }; > +}; > + > +/* Seems like ADSP really insists on managing those itself */ > +&lpasscc { status = "disabled"; }; > +&lpass_hm { status = "disabled"; }; No wrapping. > + > +&mdp { > + status = "okay"; > +}; > + > +&mdss { > + status = "okay"; > +}; > + > +&pm6150_adc { > + thermistor@4e { > + reg = <ADC5_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + }; > + > + charger-thermistor@4f { > + reg = <ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + }; > +}; > + > +&pm6150_adc_tm { > + status = "okay"; > + > + charger-thermistor@0 { > + reg = <0>; > + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + thermistor@1 { > + reg = <1>; > + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > +}; > + > +&pm6150_pon { status = "disabled"; }; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&remoteproc_mpss { > + firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn"; > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-0 = <&sdc1_default>; > + pinctrl-1 = <&sdc1_sleep>; > + pinctrl-names = "default", "sleep"; > + vmmc-supply = <&vreg_l19a_2p9>; > + vqmmc-supply = <&vreg_l12a_1p8>; > + > + status = "okay"; > +}; > + > +&uart3 { > + /delete-property/interrupts; > + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, > + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; Looks not aligned. > + > + pinctrl-1 = <&qup_uart3_sleep>; > + pinctrl-names = "default", "sleep"; > + > + status = "okay"; > + > + bluetooth: bluetooth { > + compatible = "qcom,wcn3991-bt"; > + vddio-supply = <&vreg_l10a_1p8>; > + vddxo-supply = <&vreg_l1c_1p8>; > + vddrf-supply = <&vreg_l2c_1p3>; > + vddch0-supply = <&vreg_l10c_3p3>; > + max-speed = <3200000>; > + }; > +}; > + > +&uart8 { > + status = "okay"; > +}; > + > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "host"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + usb_hub_2_x: hub@1 { > + compatible = "usbbda,5411"; > + reg = <1>; > + peer-hub = <&usb_hub_3_x>; > + }; > + > + usb_hub_3_x: hub@2 { > + compatible = "usbbda,411"; > + reg = <2>; > + peer-hub = <&usb_hub_2_x>; > + }; > +}; > + > +&usb_1_hsphy { > + vdd-supply = <&vreg_l4a_0p8>; > + vdda-pll-supply = <&vreg_l11a_1p8>; > + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; > + qcom,imp-res-offset-value = <8>; > + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; > + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; > + qcom,bias-ctrl-value = <0x22>; > + qcom,charge-ctrl-value = <3>; > + qcom,hsdisc-trim-value = <0>; > + > + status = "okay"; > +}; > + > +&usb_1_qmpphy { > + vdda-phy-supply = <&vreg_l3c_1p2>; > + vdda-pll-supply = <&vreg_l4a_0p8>; > + status = "okay"; > +}; > + > +&venus { > + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn"; > +}; > + > +&wifi { > + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; > + vdd-1.8-xo-supply = <&vreg_l1c_1p8>; > + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; > + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; > + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; > + status = "okay"; > +}; > + > +&apps_rsc { > + pm6150-rpmh-regulators { regulators-0 We fixed it some time ago, so: Does not look like you tested the DTS against bindings. Please run `make dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). > + compatible = "qcom,pm6150-rpmh-regulators"; > + qcom,pmic-id = "a"; > + > + vreg_s1a_1p1: smps1 { > + regulator-min-microvolt = <1128000>; > + regulator-max-microvolt = <1128000>; > + }; > + > + vreg_l4a_0p8: ldo4 { > + regulator-min-microvolt = <824000>; > + regulator-max-microvolt = <928000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9a_0p6: ldo9 { > + regulator-min-microvolt = <488000>; > + regulator-max-microvolt = <800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10a_1p8: ldo10 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vreg_l11a_1p8: ldo11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12a_1p8: ldo12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13a_1p8: ldo13 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l14a_1p8: ldo14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l15a_1p8: ldo15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16a_2p7: ldo16 { > + regulator-min-microvolt = <2496000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l17a_3p0: ldo17 { > + regulator-min-microvolt = <2920000>; > + regulator-max-microvolt = <3232000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l18a_2p8: ldo18 { > + regulator-min-microvolt = <2496000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l19a_2p9: ldo19 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + pm6150l-rpmh-regulators { Does not look like you tested the DTS against bindings. Please run `make dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst for instructions). Best regards, Krzysztof
Krzysztof Kozlowski писал(а) 14.03.2023 13:26: > On 14/03/2023 07:43, Nikita Travkin wrote: >> Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform. >> >> The laptop design is similar to trogdor in the choice of primary >> components but the specifics on usage of those differ slightly. >> >> Add the devicetree for the laptop with support for most of the >> hardware present. >> > > Thank you for your patch. There is something to discuss/improve. > >> +/ { >> + model = "Acer Aspire 1"; >> + compatible = "acer,aspire1", "qcom,sc7180"; >> + chassis-type = "laptop"; >> + >> + reserved-memory { > > Wrong ordering. Top-level nodes go alphanumeric. > Oops, missed it. I will sort the DT spec nodes (this, aliases, chosen) but I would like to still keep them on top to separate them from devices. If you think the nodes must be sorted regardless of the semantics, please let me know. >> + zap_mem: zap-shader@80840000 { >> + reg = <0 0x80840000 0 0x2000>; >> + no-map; >> + }; >> + >> + venus_mem: venus@85b00000 { >> + reg = <0 0x85b00000 0 0x500000>; >> + no-map; >> + }; >> + >> + mpss_mem: mpss@86000000 { >> + reg = <0x0 0x86000000 0x0 0x2000000>; >> + no-map; >> + }; >> + >> + adsp_mem: adsp@8e400000 { >> + reg = <0x0 0x8e400000 0x0 0x2800000>; >> + no-map; >> + }; >> + >> + wlan_mem: wlan@93900000 { >> + reg = <0x0 0x93900000 0x0 0x200000>; >> + no-map; >> + }; >> + }; >> + >> + aliases { >> + bluetooth0 = &bluetooth; >> + hsuart0 = &uart3; >> + serial0 = &uart8; >> + wifi0 = &wifi; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> + >> + max98357a: audio-codec-0 { > > Do you have second audio-codec? If not, drop -0. > There are two physical chips (L,R) but I think they are represented by a single node. I will check if I missed something while "inheriting" this but will probably drop the suffix. > >> + compatible = "maxim,max98357a"; >> + sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; >> + >> + pinctrl-0 = <&_sd_mode_default>; >> + pinctrl-names = "default"; >> + >> + #sound-dai-cells = <0>; >> + }; >> + >> + backlight: backlight { >> + compatible = "pwm-backlight"; >> + pwms = <&sn65dsi86_bridge 1000000>; >> + enable-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; >> + >> + pinctrl-0 = <&soc_bkoff_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + reg_brij_1p2: bridge-1p2-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "brij_1p2"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + >> + gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + >> + pinctrl-0 = <®_edp_1p2_en_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + reg_brij_1p8: bridge-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "brij_1p8"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + >> + vin-supply = <&vreg_l8c_1p8>; >> + >> + gpio = <&tlmm 20 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + >> + pinctrl-0 = <®_edp_1p8_en_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + reg_codec_3p3: codec-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "codec_3p3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + >> + gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + >> + pinctrl-0 = <®_audio_en_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + reg_lcm_3p3: panel-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "lcm_3p3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + > > /* > * Comment starts here > Will fix all comments, wraps and alignments. > >> + /* HACK: Display fails with >> + * >> + * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz >> + * *ERROR* Link training failed, link is off (-5) >> + * >> + * if the power to the panel was ever cut >> + */ > > >> +}; >> + >> +&camcc { status = "disabled"; }; > > Don't wrap nodes. > >> + >> +&dsi0 { >> + vdda-supply = <&vreg_l3c_1p2>; >> + status = "okay"; >> +}; >> + >> +&dsi0_out { >> + remote-endpoint = <&sn65dsi86_in>; >> + data-lanes = <0 1 2 3>; >> +}; >> + >> +&dsi_phy { >> + vdds-supply = <&vreg_l4a_0p8>; >> + status = "okay"; >> +}; >> + >> +&i2c2 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + /* embedded-controller@76 */ >> +}; >> + >> +&i2c4 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + /* >> + * NOTE: DSDT defines two possible touchpads, other one is >> + * >> + * reg = <0x15>; >> + * hid-descr-addr = <0x1>; >> + */ >> + >> + touchpad@2c { >> + compatible = "hid-over-i2c"; >> + reg = <0x2c>; >> + hid-descr-addr = <0x20>; >> + >> + vdd-supply = <®_tp_3p3>; >> + >> + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>; >> + >> + pinctrl-0 = <&hid_touchpad_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + keyboard@3a { >> + compatible = "hid-over-i2c"; >> + reg = <0x3a>; >> + hid-descr-addr = <0x1>; >> + >> + interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>; >> + >> + pinctrl-0 = <&hid_keyboard_default>; >> + pinctrl-names = "default"; >> + >> + wakeup-source; >> + }; >> +}; >> + >> +&i2c9 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + alc5682: codec@1a { >> + compatible = "realtek,rt5682i"; >> + reg = <0x1a>; >> + >> + #sound-dai-cells = <1>; >> + >> + interrupt-parent = <&tlmm>; >> + /* >> + * This will get ignored because the interrupt type >> + * is set in rt5682.c. > > Don't add Linux driver stuff to DTS. Not relevant, so drop the comment. > I think this was "inherited" from sc7180-trogdor.dtsi Will drop. >> + */ >> + interrupts = <28 IRQ_TYPE_EDGE_BOTH>; >> + >> + pinctrl-0 = <&codec_irq_default>; >> + pinctrl-names = "default"; >> + >> + AVDD-supply = <&vreg_l15a_1p8>; >> + MICVDD-supply = <®_codec_3p3>; >> + VBAT-supply = <®_codec_3p3>; >> + >> + realtek,dmic1-data-pin = <1>; >> + realtek,dmic1-clk-pin = <1>; >> + realtek,jd-src = <1>; >> + }; >> +}; >> + >> +&i2c10 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + sn65dsi86_bridge: bridge@2c { >> + compatible = "ti,sn65dsi86"; >> + reg = <0x2c>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + #pwm-cells = <1>; >> + >> + interrupt-parent = <&tlmm>; >> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; >> + >> + enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; >> + suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; >> + >> + pinctrl-0 = <&bridge_en_default>, >> + <&edp_bridge_irq_default>, >> + <&bridge_suspend_default>; > > Align entries. > >> + pinctrl-names = "default"; >> + >> + vpll-supply = <®_brij_1p8>; >> + vccio-supply = <®_brij_1p8>; >> + vcca-supply = <®_brij_1p2>; >> + vcc-supply = <®_brij_1p2>; >> + >> + clocks = <&rpmhcc RPMH_LN_BB_CLK3>; >> + clock-names = "refclk"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + sn65dsi86_in: endpoint { >> + remote-endpoint = <&dsi0_out>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + sn65dsi86_out: endpoint { >> + data-lanes = <0 1>; >> + remote-endpoint = <&panel_in_edp>; >> + }; >> + }; >> + }; >> + >> + aux-bus { >> + panel: panel { >> + compatible = "edp-panel"; >> + power-supply = <®_lcm_3p3>; >> + backlight = <&backlight>; >> + >> + port { >> + panel_in_edp: endpoint { >> + remote-endpoint = <&sn65dsi86_out>; >> + }; >> + }; >> + }; >> + }; >> + }; >> +}; >> + >> +&gpu { >> + status = "okay"; >> + >> + zap-shader { >> + memory-region = <&zap_mem>; >> + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn"; >> + }; >> +}; >> + >> +/* Seems like ADSP really insists on managing those itself */ >> +&lpasscc { status = "disabled"; }; >> +&lpass_hm { status = "disabled"; }; > > No wrapping. > >> + >> +&mdp { >> + status = "okay"; >> +}; >> + >> +&mdss { >> + status = "okay"; >> +}; >> + >> +&pm6150_adc { >> + thermistor@4e { >> + reg = <ADC5_AMUX_THM2_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time = <200>; >> + }; >> + >> + charger-thermistor@4f { >> + reg = <ADC5_AMUX_THM3_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time = <200>; >> + }; >> +}; >> + >> +&pm6150_adc_tm { >> + status = "okay"; >> + >> + charger-thermistor@0 { >> + reg = <0>; >> + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time-us = <200>; >> + }; >> + >> + thermistor@1 { >> + reg = <1>; >> + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time-us = <200>; >> + }; >> +}; >> + >> +&pm6150_pon { status = "disabled"; }; >> + >> +&qupv3_id_0 { >> + status = "okay"; >> +}; >> + >> +&qupv3_id_1 { >> + status = "okay"; >> +}; >> + >> +&remoteproc_mpss { >> + firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn"; >> + status = "okay"; >> +}; >> + >> +&sdhc_1 { >> + pinctrl-0 = <&sdc1_default>; >> + pinctrl-1 = <&sdc1_sleep>; >> + pinctrl-names = "default", "sleep"; >> + vmmc-supply = <&vreg_l19a_2p9>; >> + vqmmc-supply = <&vreg_l12a_1p8>; >> + >> + status = "okay"; >> +}; >> + >> +&uart3 { >> + /delete-property/interrupts; >> + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, >> + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; > > Looks not aligned. > >> + >> + pinctrl-1 = <&qup_uart3_sleep>; >> + pinctrl-names = "default", "sleep"; >> + >> + status = "okay"; >> + >> + bluetooth: bluetooth { >> + compatible = "qcom,wcn3991-bt"; >> + vddio-supply = <&vreg_l10a_1p8>; >> + vddxo-supply = <&vreg_l1c_1p8>; >> + vddrf-supply = <&vreg_l2c_1p3>; >> + vddch0-supply = <&vreg_l10c_3p3>; >> + max-speed = <3200000>; >> + }; >> +}; >> + >> +&uart8 { >> + status = "okay"; >> +}; >> + >> +&usb_1 { >> + status = "okay"; >> +}; >> + >> +&usb_1_dwc3 { >> + dr_mode = "host"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + usb_hub_2_x: hub@1 { >> + compatible = "usbbda,5411"; >> + reg = <1>; >> + peer-hub = <&usb_hub_3_x>; >> + }; >> + >> + usb_hub_3_x: hub@2 { >> + compatible = "usbbda,411"; >> + reg = <2>; >> + peer-hub = <&usb_hub_2_x>; >> + }; >> +}; >> + >> +&usb_1_hsphy { >> + vdd-supply = <&vreg_l4a_0p8>; >> + vdda-pll-supply = <&vreg_l11a_1p8>; >> + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; >> + qcom,imp-res-offset-value = <8>; >> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; >> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; >> + qcom,bias-ctrl-value = <0x22>; >> + qcom,charge-ctrl-value = <3>; >> + qcom,hsdisc-trim-value = <0>; >> + >> + status = "okay"; >> +}; >> + >> +&usb_1_qmpphy { >> + vdda-phy-supply = <&vreg_l3c_1p2>; >> + vdda-pll-supply = <&vreg_l4a_0p8>; >> + status = "okay"; >> +}; >> + >> +&venus { >> + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn"; >> +}; >> + >> +&wifi { >> + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; >> + vdd-1.8-xo-supply = <&vreg_l1c_1p8>; >> + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; >> + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; >> + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; >> + status = "okay"; >> +}; >> + >> +&apps_rsc { >> + pm6150-rpmh-regulators { > > regulators-0 > Oops, I guess I've missed this warning, will do. Thanks for the review! Nikita > We fixed it some time ago, so: > Does not look like you tested the DTS against bindings. Please run `make > dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst > for instructions). > >> + compatible = "qcom,pm6150-rpmh-regulators"; >> + qcom,pmic-id = "a"; >> + >> + vreg_s1a_1p1: smps1 { >> + regulator-min-microvolt = <1128000>; >> + regulator-max-microvolt = <1128000>; >> + }; >> + >> + vreg_l4a_0p8: ldo4 { >> + regulator-min-microvolt = <824000>; >> + regulator-max-microvolt = <928000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l9a_0p6: ldo9 { >> + regulator-min-microvolt = <488000>; >> + regulator-max-microvolt = <800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l10a_1p8: ldo10 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + >> + regulator-always-on; >> + regulator-boot-on; >> + }; >> + >> + vreg_l11a_1p8: ldo11 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l12a_1p8: ldo12 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l13a_1p8: ldo13 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l14a_1p8: ldo14 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l15a_1p8: ldo15 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l16a_2p7: ldo16 { >> + regulator-min-microvolt = <2496000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l17a_3p0: ldo17 { >> + regulator-min-microvolt = <2920000>; >> + regulator-max-microvolt = <3232000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l18a_2p8: ldo18 { >> + regulator-min-microvolt = <2496000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l19a_2p9: ldo19 { >> + regulator-min-microvolt = <2960000>; >> + regulator-max-microvolt = <2960000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + pm6150l-rpmh-regulators { > > Does not look like you tested the DTS against bindings. Please run `make > dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst > for instructions). > > > > Best regards, > Krzysztof
On 14.03.2023 07:43, Nikita Travkin wrote: > Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform. > > The laptop design is similar to trogdor in the choice of primary > components but the specifics on usage of those differ slightly. > > Add the devicetree for the laptop with support for most of the > hardware present. > > Signed-off-by: Nikita Travkin <nikita@trvn.ru> > --- [...] > + /* HACK: Display fails with > + * > + * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz > + * *ERROR* Link training failed, link is off (-5) > + * > + * if the power to the panel was ever cut Your ACPI tables mention a single FSTATE where this regulator is off, may be worth looking into at some point, perhaps you need a more in-depth en-/disable sequence. Konrad > + */ > + regulator-always-on; > + > + gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + pinctrl-0 = <®_lcm_en_default>; > + pinctrl-names = "default"; > + }; > + > + reg_tp_3p3: touchpad-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "tp_3p3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + > + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + > + pinctrl-0 = <®_tp_en_default>; > + pinctrl-names = "default"; > + }; > +}; > + > +&camcc { status = "disabled"; }; > + > +&dsi0 { > + vdda-supply = <&vreg_l3c_1p2>; > + status = "okay"; > +}; > + > +&dsi0_out { > + remote-endpoint = <&sn65dsi86_in>; > + data-lanes = <0 1 2 3>; > +}; > + > +&dsi_phy { > + vdds-supply = <&vreg_l4a_0p8>; > + status = "okay"; > +}; > + > +&i2c2 { > + clock-frequency = <400000>; > + status = "okay"; > + > + /* embedded-controller@76 */ > +}; > + > +&i2c4 { > + clock-frequency = <400000>; > + status = "okay"; > + > + /* > + * NOTE: DSDT defines two possible touchpads, other one is > + * > + * reg = <0x15>; > + * hid-descr-addr = <0x1>; > + */ > + > + touchpad@2c { > + compatible = "hid-over-i2c"; > + reg = <0x2c>; > + hid-descr-addr = <0x20>; > + > + vdd-supply = <®_tp_3p3>; > + > + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-0 = <&hid_touchpad_default>; > + pinctrl-names = "default"; > + }; > + > + keyboard@3a { > + compatible = "hid-over-i2c"; > + reg = <0x3a>; > + hid-descr-addr = <0x1>; > + > + interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>; > + > + pinctrl-0 = <&hid_keyboard_default>; > + pinctrl-names = "default"; > + > + wakeup-source; > + }; > +}; > + > +&i2c9 { > + clock-frequency = <400000>; > + status = "okay"; > + > + alc5682: codec@1a { > + compatible = "realtek,rt5682i"; > + reg = <0x1a>; > + > + #sound-dai-cells = <1>; > + > + interrupt-parent = <&tlmm>; > + /* > + * This will get ignored because the interrupt type > + * is set in rt5682.c. > + */ > + interrupts = <28 IRQ_TYPE_EDGE_BOTH>; > + > + pinctrl-0 = <&codec_irq_default>; > + pinctrl-names = "default"; > + > + AVDD-supply = <&vreg_l15a_1p8>; > + MICVDD-supply = <®_codec_3p3>; > + VBAT-supply = <®_codec_3p3>; > + > + realtek,dmic1-data-pin = <1>; > + realtek,dmic1-clk-pin = <1>; > + realtek,jd-src = <1>; > + }; > +}; > + > +&i2c10 { > + clock-frequency = <400000>; > + status = "okay"; > + > + sn65dsi86_bridge: bridge@2c { > + compatible = "ti,sn65dsi86"; > + reg = <0x2c>; > + gpio-controller; > + #gpio-cells = <2>; > + #pwm-cells = <1>; > + > + interrupt-parent = <&tlmm>; > + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; > + > + enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; > + suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; > + > + pinctrl-0 = <&bridge_en_default>, > + <&edp_bridge_irq_default>, > + <&bridge_suspend_default>; > + pinctrl-names = "default"; > + > + vpll-supply = <®_brij_1p8>; > + vccio-supply = <®_brij_1p8>; > + vcca-supply = <®_brij_1p2>; > + vcc-supply = <®_brij_1p2>; > + > + clocks = <&rpmhcc RPMH_LN_BB_CLK3>; > + clock-names = "refclk"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + sn65dsi86_in: endpoint { > + remote-endpoint = <&dsi0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + sn65dsi86_out: endpoint { > + data-lanes = <0 1>; > + remote-endpoint = <&panel_in_edp>; > + }; > + }; > + }; > + > + aux-bus { > + panel: panel { > + compatible = "edp-panel"; > + power-supply = <®_lcm_3p3>; > + backlight = <&backlight>; > + > + port { > + panel_in_edp: endpoint { > + remote-endpoint = <&sn65dsi86_out>; > + }; > + }; > + }; > + }; > + }; > +}; > + > +&gpu { > + status = "okay"; > + > + zap-shader { > + memory-region = <&zap_mem>; > + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn"; > + }; > +}; > + > +/* Seems like ADSP really insists on managing those itself */ > +&lpasscc { status = "disabled"; }; > +&lpass_hm { status = "disabled"; }; > + > +&mdp { > + status = "okay"; > +}; > + > +&mdss { > + status = "okay"; > +}; > + > +&pm6150_adc { > + thermistor@4e { > + reg = <ADC5_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + }; > + > + charger-thermistor@4f { > + reg = <ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + }; > +}; > + > +&pm6150_adc_tm { > + status = "okay"; > + > + charger-thermistor@0 { > + reg = <0>; > + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + thermistor@1 { > + reg = <1>; > + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > +}; > + > +&pm6150_pon { status = "disabled"; }; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&remoteproc_mpss { > + firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn"; > + status = "okay"; > +}; > + > +&sdhc_1 { > + pinctrl-0 = <&sdc1_default>; > + pinctrl-1 = <&sdc1_sleep>; > + pinctrl-names = "default", "sleep"; > + vmmc-supply = <&vreg_l19a_2p9>; > + vqmmc-supply = <&vreg_l12a_1p8>; > + > + status = "okay"; > +}; > + > +&uart3 { > + /delete-property/interrupts; > + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, > + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; > + > + pinctrl-1 = <&qup_uart3_sleep>; > + pinctrl-names = "default", "sleep"; > + > + status = "okay"; > + > + bluetooth: bluetooth { > + compatible = "qcom,wcn3991-bt"; > + vddio-supply = <&vreg_l10a_1p8>; > + vddxo-supply = <&vreg_l1c_1p8>; > + vddrf-supply = <&vreg_l2c_1p3>; > + vddch0-supply = <&vreg_l10c_3p3>; > + max-speed = <3200000>; > + }; > +}; > + > +&uart8 { > + status = "okay"; > +}; > + > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "host"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + usb_hub_2_x: hub@1 { > + compatible = "usbbda,5411"; > + reg = <1>; > + peer-hub = <&usb_hub_3_x>; > + }; > + > + usb_hub_3_x: hub@2 { > + compatible = "usbbda,411"; > + reg = <2>; > + peer-hub = <&usb_hub_2_x>; > + }; > +}; > + > +&usb_1_hsphy { > + vdd-supply = <&vreg_l4a_0p8>; > + vdda-pll-supply = <&vreg_l11a_1p8>; > + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; > + qcom,imp-res-offset-value = <8>; > + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; > + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; > + qcom,bias-ctrl-value = <0x22>; > + qcom,charge-ctrl-value = <3>; > + qcom,hsdisc-trim-value = <0>; > + > + status = "okay"; > +}; > + > +&usb_1_qmpphy { > + vdda-phy-supply = <&vreg_l3c_1p2>; > + vdda-pll-supply = <&vreg_l4a_0p8>; > + status = "okay"; > +}; > + > +&venus { > + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn"; > +}; > + > +&wifi { > + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; > + vdd-1.8-xo-supply = <&vreg_l1c_1p8>; > + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; > + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; > + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; > + status = "okay"; > +}; > + > +&apps_rsc { > + pm6150-rpmh-regulators { > + compatible = "qcom,pm6150-rpmh-regulators"; > + qcom,pmic-id = "a"; > + > + vreg_s1a_1p1: smps1 { > + regulator-min-microvolt = <1128000>; > + regulator-max-microvolt = <1128000>; > + }; > + > + vreg_l4a_0p8: ldo4 { > + regulator-min-microvolt = <824000>; > + regulator-max-microvolt = <928000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9a_0p6: ldo9 { > + regulator-min-microvolt = <488000>; > + regulator-max-microvolt = <800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10a_1p8: ldo10 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + > + regulator-always-on; > + regulator-boot-on; > + }; > + > + vreg_l11a_1p8: ldo11 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12a_1p8: ldo12 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13a_1p8: ldo13 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l14a_1p8: ldo14 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l15a_1p8: ldo15 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16a_2p7: ldo16 { > + regulator-min-microvolt = <2496000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l17a_3p0: ldo17 { > + regulator-min-microvolt = <2920000>; > + regulator-max-microvolt = <3232000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l18a_2p8: ldo18 { > + regulator-min-microvolt = <2496000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l19a_2p9: ldo19 { > + regulator-min-microvolt = <2960000>; > + regulator-max-microvolt = <2960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + pm6150l-rpmh-regulators { > + compatible = "qcom,pm6150l-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vreg_s8c_1p3: smps8 { > + regulator-min-microvolt = <1120000>; > + regulator-max-microvolt = <1408000>; > + }; > + > + vreg_l1c_1p8: ldo1 { > + regulator-min-microvolt = <1616000>; > + regulator-max-microvolt = <1984000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2c_1p3: ldo2 { > + regulator-min-microvolt = <1168000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3c_1p2: ldo3 { > + regulator-min-microvolt = <1144000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4c_1p8: ldo4 { > + regulator-min-microvolt = <1648000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; > + }; > + > + vreg_l5c_1p8: ldo5 { > + regulator-min-microvolt = <1648000>; > + regulator-max-microvolt = <3304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; > + }; > + > + vreg_l6c_2p9: ldo6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2950000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7c_3p0: ldo7 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3312000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; > + }; > + > + vreg_l8c_1p8: ldo8 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9c_2p9: ldo9 { > + regulator-min-microvolt = <2952000>; > + regulator-max-microvolt = <2952000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10c_3p3: ldo10 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3400000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11c_3p3: ldo11 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3400000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > + }; > + }; > +}; > + > +&qup_i2c2_default { > + drive-strength = <2>; > + > + /* Has external pullup */ > + bias-disable; > +}; > + > +&qup_i2c4_default { > + drive-strength = <2>; > + > + /* Has external pullup */ > + bias-disable; > +}; > + > +&qup_i2c9_default { > + drive-strength = <2>; > + > + /* Has external pullup */ > + bias-disable; > +}; > + > +&qup_i2c10_default { > + drive-strength = <2>; > + > + /* Has external pullup */ > + bias-disable; > +}; > + > +&tlmm { > + /* > + * The TZ seem to protect those because some boards can have > + * fingerprint sensor connected to this range. Not connected > + * on this board > + */ > + gpio-reserved-ranges = <58 5>; > + > + amp_sd_mode_default: amp-sd-mode-deault-state { > + pins = "gpio23"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + bridge_en_default: bridge-en-default-state { > + pins = "gpio51"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + bridge_suspend_default: bridge-suspend-default-state { > + pins = "gpio22"; > + function = "gpio"; > + drive-strength = <16>; > + bias-pull-up; > + }; > + > + codec_irq_default: codec-irq-deault-state { > + pins = "gpio28"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + edp_bridge_irq_default: edp-bridge-irq-default-state { > + pins = "gpio11"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-down; > + }; > + > + hid_keyboard_default: hid-keyboard-default-state { > + pins = "gpio33"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + hid_touchpad_default: hid-touchpad-default-state { > + pins = "gpio94"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + qup_uart3_sleep: qup-uart3-sleep-state { > + cts-pins { > + /* > + * Configure a pull-down on CTS to match the pull of > + * the Bluetooth module. > + */ > + pins = "gpio38"; > + function = "gpio"; > + bias-pull-down; > + }; > + > + rts-pins { > + /* > + * Configure pull-down on RTS. As RTS is active low > + * signal, pull it low to indicate the BT SoC that it > + * can wakeup the system anytime from suspend state by > + * pulling RX low (by sending wakeup bytes). > + */ > + pins = "gpio39"; > + function = "gpio"; > + bias-pull-down; > + }; > + > + tx-pins { > + /* > + * Configure pull-up on TX when it isn't actively driven > + * to prevent BT SoC from receiving garbage during sleep. > + */ > + pins = "gpio40"; > + function = "gpio"; > + bias-pull-up; > + }; > + > + rx-pins { > + /* > + * Configure a pull-up on RX. This is needed to avoid > + * garbage data when the TX pin of the Bluetooth module > + * is floating which may cause spurious wakeups. > + */ > + pins = "gpio41"; > + function = "gpio"; > + bias-pull-up; > + }; > + }; > + > + reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state { > + pins = "gpio19"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state { > + pins = "gpio20"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + reg_lcm_en_default: reg-lcm-en-deault-state { > + pins = "gpio26"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + reg_audio_en_default: reg-audio-en-deault-state { > + pins = "gpio83"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + reg_tp_en_default: reg-tp-en-deault-state { > + pins = "gpio25"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; > + > + soc_bkoff_default: soc-bkoff-deault-state { > + pins = "gpio10"; > + function = "gpio"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + sdc1_default: sdc1-default-state { > + clk-pins { > + pins = "sdc1_clk"; > + bias-disable; > + drive-strength = <16>; > + }; > + > + cmd-pins { > + pins = "sdc1_cmd"; > + bias-pull-up; > + drive-strength = <16>; > + }; > + > + data-pins { > + pins = "sdc1_data"; > + bias-pull-up; > + drive-strength = <16>; > + }; > + > + rclk-pins { > + pins = "sdc1_rclk"; > + bias-pull-down; > + }; > + }; > + > + sdc1_sleep: sdc1-sleep-state { > + clk-pins { > + pins = "sdc1_clk"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + cmd-pins { > + pins = "sdc1_cmd"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + data-pins { > + pins = "sdc1_data"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + rclk-pins { > + pins = "sdc1_rclk"; > + bias-pull-down; > + }; > + }; > + > + ter_mi2s_active: ter-mi2s-active-state { > + pins = "gpio63", "gpio64", "gpio65"; > + function = "mi2s_2"; > + }; > +};
Konrad Dybcio писал(а) 14.03.2023 15:24: > On 14.03.2023 07:43, Nikita Travkin wrote: >> Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform. >> >> The laptop design is similar to trogdor in the choice of primary >> components but the specifics on usage of those differ slightly. >> >> Add the devicetree for the laptop with support for most of the >> hardware present. >> >> Signed-off-by: Nikita Travkin <nikita@trvn.ru> >> --- > [...] >> + /* HACK: Display fails with >> + * >> + * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz >> + * *ERROR* Link training failed, link is off (-5) >> + * >> + * if the power to the panel was ever cut > Your ACPI tables mention a single FSTATE where this regulator is > off, may be worth looking into at some point, perhaps you need > a more in-depth en-/disable sequence. > Yes, I want to get to the bottom of this eventually, thus making it clear this is a hack. Thanks for looking at it! Nikita > Konrad >> + */ >> + regulator-always-on; >> + >> + gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + >> + pinctrl-0 = <®_lcm_en_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + reg_tp_3p3: touchpad-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "tp_3p3"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + >> + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; >> + enable-active-high; >> + >> + pinctrl-0 = <®_tp_en_default>; >> + pinctrl-names = "default"; >> + }; >> +}; >> + >> +&camcc { status = "disabled"; }; >> + >> +&dsi0 { >> + vdda-supply = <&vreg_l3c_1p2>; >> + status = "okay"; >> +}; >> + >> +&dsi0_out { >> + remote-endpoint = <&sn65dsi86_in>; >> + data-lanes = <0 1 2 3>; >> +}; >> + >> +&dsi_phy { >> + vdds-supply = <&vreg_l4a_0p8>; >> + status = "okay"; >> +}; >> + >> +&i2c2 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + /* embedded-controller@76 */ >> +}; >> + >> +&i2c4 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + /* >> + * NOTE: DSDT defines two possible touchpads, other one is >> + * >> + * reg = <0x15>; >> + * hid-descr-addr = <0x1>; >> + */ >> + >> + touchpad@2c { >> + compatible = "hid-over-i2c"; >> + reg = <0x2c>; >> + hid-descr-addr = <0x20>; >> + >> + vdd-supply = <®_tp_3p3>; >> + >> + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>; >> + >> + pinctrl-0 = <&hid_touchpad_default>; >> + pinctrl-names = "default"; >> + }; >> + >> + keyboard@3a { >> + compatible = "hid-over-i2c"; >> + reg = <0x3a>; >> + hid-descr-addr = <0x1>; >> + >> + interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>; >> + >> + pinctrl-0 = <&hid_keyboard_default>; >> + pinctrl-names = "default"; >> + >> + wakeup-source; >> + }; >> +}; >> + >> +&i2c9 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + alc5682: codec@1a { >> + compatible = "realtek,rt5682i"; >> + reg = <0x1a>; >> + >> + #sound-dai-cells = <1>; >> + >> + interrupt-parent = <&tlmm>; >> + /* >> + * This will get ignored because the interrupt type >> + * is set in rt5682.c. >> + */ >> + interrupts = <28 IRQ_TYPE_EDGE_BOTH>; >> + >> + pinctrl-0 = <&codec_irq_default>; >> + pinctrl-names = "default"; >> + >> + AVDD-supply = <&vreg_l15a_1p8>; >> + MICVDD-supply = <®_codec_3p3>; >> + VBAT-supply = <®_codec_3p3>; >> + >> + realtek,dmic1-data-pin = <1>; >> + realtek,dmic1-clk-pin = <1>; >> + realtek,jd-src = <1>; >> + }; >> +}; >> + >> +&i2c10 { >> + clock-frequency = <400000>; >> + status = "okay"; >> + >> + sn65dsi86_bridge: bridge@2c { >> + compatible = "ti,sn65dsi86"; >> + reg = <0x2c>; >> + gpio-controller; >> + #gpio-cells = <2>; >> + #pwm-cells = <1>; >> + >> + interrupt-parent = <&tlmm>; >> + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; >> + >> + enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; >> + suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; >> + >> + pinctrl-0 = <&bridge_en_default>, >> + <&edp_bridge_irq_default>, >> + <&bridge_suspend_default>; >> + pinctrl-names = "default"; >> + >> + vpll-supply = <®_brij_1p8>; >> + vccio-supply = <®_brij_1p8>; >> + vcca-supply = <®_brij_1p2>; >> + vcc-supply = <®_brij_1p2>; >> + >> + clocks = <&rpmhcc RPMH_LN_BB_CLK3>; >> + clock-names = "refclk"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + port@0 { >> + reg = <0>; >> + >> + sn65dsi86_in: endpoint { >> + remote-endpoint = <&dsi0_out>; >> + }; >> + }; >> + >> + port@1 { >> + reg = <1>; >> + >> + sn65dsi86_out: endpoint { >> + data-lanes = <0 1>; >> + remote-endpoint = <&panel_in_edp>; >> + }; >> + }; >> + }; >> + >> + aux-bus { >> + panel: panel { >> + compatible = "edp-panel"; >> + power-supply = <®_lcm_3p3>; >> + backlight = <&backlight>; >> + >> + port { >> + panel_in_edp: endpoint { >> + remote-endpoint = <&sn65dsi86_out>; >> + }; >> + }; >> + }; >> + }; >> + }; >> +}; >> + >> +&gpu { >> + status = "okay"; >> + >> + zap-shader { >> + memory-region = <&zap_mem>; >> + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn"; >> + }; >> +}; >> + >> +/* Seems like ADSP really insists on managing those itself */ >> +&lpasscc { status = "disabled"; }; >> +&lpass_hm { status = "disabled"; }; >> + >> +&mdp { >> + status = "okay"; >> +}; >> + >> +&mdss { >> + status = "okay"; >> +}; >> + >> +&pm6150_adc { >> + thermistor@4e { >> + reg = <ADC5_AMUX_THM2_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time = <200>; >> + }; >> + >> + charger-thermistor@4f { >> + reg = <ADC5_AMUX_THM3_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time = <200>; >> + }; >> +}; >> + >> +&pm6150_adc_tm { >> + status = "okay"; >> + >> + charger-thermistor@0 { >> + reg = <0>; >> + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time-us = <200>; >> + }; >> + >> + thermistor@1 { >> + reg = <1>; >> + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; >> + qcom,ratiometric; >> + qcom,hw-settle-time-us = <200>; >> + }; >> +}; >> + >> +&pm6150_pon { status = "disabled"; }; >> + >> +&qupv3_id_0 { >> + status = "okay"; >> +}; >> + >> +&qupv3_id_1 { >> + status = "okay"; >> +}; >> + >> +&remoteproc_mpss { >> + firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn"; >> + status = "okay"; >> +}; >> + >> +&sdhc_1 { >> + pinctrl-0 = <&sdc1_default>; >> + pinctrl-1 = <&sdc1_sleep>; >> + pinctrl-names = "default", "sleep"; >> + vmmc-supply = <&vreg_l19a_2p9>; >> + vqmmc-supply = <&vreg_l12a_1p8>; >> + >> + status = "okay"; >> +}; >> + >> +&uart3 { >> + /delete-property/interrupts; >> + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, >> + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; >> + >> + pinctrl-1 = <&qup_uart3_sleep>; >> + pinctrl-names = "default", "sleep"; >> + >> + status = "okay"; >> + >> + bluetooth: bluetooth { >> + compatible = "qcom,wcn3991-bt"; >> + vddio-supply = <&vreg_l10a_1p8>; >> + vddxo-supply = <&vreg_l1c_1p8>; >> + vddrf-supply = <&vreg_l2c_1p3>; >> + vddch0-supply = <&vreg_l10c_3p3>; >> + max-speed = <3200000>; >> + }; >> +}; >> + >> +&uart8 { >> + status = "okay"; >> +}; >> + >> +&usb_1 { >> + status = "okay"; >> +}; >> + >> +&usb_1_dwc3 { >> + dr_mode = "host"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + usb_hub_2_x: hub@1 { >> + compatible = "usbbda,5411"; >> + reg = <1>; >> + peer-hub = <&usb_hub_3_x>; >> + }; >> + >> + usb_hub_3_x: hub@2 { >> + compatible = "usbbda,411"; >> + reg = <2>; >> + peer-hub = <&usb_hub_2_x>; >> + }; >> +}; >> + >> +&usb_1_hsphy { >> + vdd-supply = <&vreg_l4a_0p8>; >> + vdda-pll-supply = <&vreg_l11a_1p8>; >> + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; >> + qcom,imp-res-offset-value = <8>; >> + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; >> + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; >> + qcom,bias-ctrl-value = <0x22>; >> + qcom,charge-ctrl-value = <3>; >> + qcom,hsdisc-trim-value = <0>; >> + >> + status = "okay"; >> +}; >> + >> +&usb_1_qmpphy { >> + vdda-phy-supply = <&vreg_l3c_1p2>; >> + vdda-pll-supply = <&vreg_l4a_0p8>; >> + status = "okay"; >> +}; >> + >> +&venus { >> + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn"; >> +}; >> + >> +&wifi { >> + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; >> + vdd-1.8-xo-supply = <&vreg_l1c_1p8>; >> + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; >> + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; >> + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; >> + status = "okay"; >> +}; >> + >> +&apps_rsc { >> + pm6150-rpmh-regulators { >> + compatible = "qcom,pm6150-rpmh-regulators"; >> + qcom,pmic-id = "a"; >> + >> + vreg_s1a_1p1: smps1 { >> + regulator-min-microvolt = <1128000>; >> + regulator-max-microvolt = <1128000>; >> + }; >> + >> + vreg_l4a_0p8: ldo4 { >> + regulator-min-microvolt = <824000>; >> + regulator-max-microvolt = <928000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l9a_0p6: ldo9 { >> + regulator-min-microvolt = <488000>; >> + regulator-max-microvolt = <800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l10a_1p8: ldo10 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + >> + regulator-always-on; >> + regulator-boot-on; >> + }; >> + >> + vreg_l11a_1p8: ldo11 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l12a_1p8: ldo12 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l13a_1p8: ldo13 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l14a_1p8: ldo14 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l15a_1p8: ldo15 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l16a_2p7: ldo16 { >> + regulator-min-microvolt = <2496000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l17a_3p0: ldo17 { >> + regulator-min-microvolt = <2920000>; >> + regulator-max-microvolt = <3232000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l18a_2p8: ldo18 { >> + regulator-min-microvolt = <2496000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l19a_2p9: ldo19 { >> + regulator-min-microvolt = <2960000>; >> + regulator-max-microvolt = <2960000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + }; >> + >> + pm6150l-rpmh-regulators { >> + compatible = "qcom,pm6150l-rpmh-regulators"; >> + qcom,pmic-id = "c"; >> + >> + vreg_s8c_1p3: smps8 { >> + regulator-min-microvolt = <1120000>; >> + regulator-max-microvolt = <1408000>; >> + }; >> + >> + vreg_l1c_1p8: ldo1 { >> + regulator-min-microvolt = <1616000>; >> + regulator-max-microvolt = <1984000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l2c_1p3: ldo2 { >> + regulator-min-microvolt = <1168000>; >> + regulator-max-microvolt = <1304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l3c_1p2: ldo3 { >> + regulator-min-microvolt = <1144000>; >> + regulator-max-microvolt = <1304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l4c_1p8: ldo4 { >> + regulator-min-microvolt = <1648000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; >> + }; >> + >> + vreg_l5c_1p8: ldo5 { >> + regulator-min-microvolt = <1648000>; >> + regulator-max-microvolt = <3304000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; >> + }; >> + >> + vreg_l6c_2p9: ldo6 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <2950000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l7c_3p0: ldo7 { >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3312000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; >> + }; >> + >> + vreg_l8c_1p8: ldo8 { >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l9c_2p9: ldo9 { >> + regulator-min-microvolt = <2952000>; >> + regulator-max-microvolt = <2952000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l10c_3p3: ldo10 { >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3400000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_l11c_3p3: ldo11 { >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3400000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; >> + }; >> + >> + vreg_bob: bob { >> + regulator-min-microvolt = <3008000>; >> + regulator-max-microvolt = <3960000>; >> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; >> + }; >> + }; >> +}; >> + >> +&qup_i2c2_default { >> + drive-strength = <2>; >> + >> + /* Has external pullup */ >> + bias-disable; >> +}; >> + >> +&qup_i2c4_default { >> + drive-strength = <2>; >> + >> + /* Has external pullup */ >> + bias-disable; >> +}; >> + >> +&qup_i2c9_default { >> + drive-strength = <2>; >> + >> + /* Has external pullup */ >> + bias-disable; >> +}; >> + >> +&qup_i2c10_default { >> + drive-strength = <2>; >> + >> + /* Has external pullup */ >> + bias-disable; >> +}; >> + >> +&tlmm { >> + /* >> + * The TZ seem to protect those because some boards can have >> + * fingerprint sensor connected to this range. Not connected >> + * on this board >> + */ >> + gpio-reserved-ranges = <58 5>; >> + >> + amp_sd_mode_default: amp-sd-mode-deault-state { >> + pins = "gpio23"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + bridge_en_default: bridge-en-default-state { >> + pins = "gpio51"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + bridge_suspend_default: bridge-suspend-default-state { >> + pins = "gpio22"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-pull-up; >> + }; >> + >> + codec_irq_default: codec-irq-deault-state { >> + pins = "gpio28"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + edp_bridge_irq_default: edp-bridge-irq-default-state { >> + pins = "gpio11"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-pull-down; >> + }; >> + >> + hid_keyboard_default: hid-keyboard-default-state { >> + pins = "gpio33"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + hid_touchpad_default: hid-touchpad-default-state { >> + pins = "gpio94"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + qup_uart3_sleep: qup-uart3-sleep-state { >> + cts-pins { >> + /* >> + * Configure a pull-down on CTS to match the pull of >> + * the Bluetooth module. >> + */ >> + pins = "gpio38"; >> + function = "gpio"; >> + bias-pull-down; >> + }; >> + >> + rts-pins { >> + /* >> + * Configure pull-down on RTS. As RTS is active low >> + * signal, pull it low to indicate the BT SoC that it >> + * can wakeup the system anytime from suspend state by >> + * pulling RX low (by sending wakeup bytes). >> + */ >> + pins = "gpio39"; >> + function = "gpio"; >> + bias-pull-down; >> + }; >> + >> + tx-pins { >> + /* >> + * Configure pull-up on TX when it isn't actively driven >> + * to prevent BT SoC from receiving garbage during sleep. >> + */ >> + pins = "gpio40"; >> + function = "gpio"; >> + bias-pull-up; >> + }; >> + >> + rx-pins { >> + /* >> + * Configure a pull-up on RX. This is needed to avoid >> + * garbage data when the TX pin of the Bluetooth module >> + * is floating which may cause spurious wakeups. >> + */ >> + pins = "gpio41"; >> + function = "gpio"; >> + bias-pull-up; >> + }; >> + }; >> + >> + reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state { >> + pins = "gpio19"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state { >> + pins = "gpio20"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + reg_lcm_en_default: reg-lcm-en-deault-state { >> + pins = "gpio26"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + reg_audio_en_default: reg-audio-en-deault-state { >> + pins = "gpio83"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + reg_tp_en_default: reg-tp-en-deault-state { >> + pins = "gpio25"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; >> + >> + soc_bkoff_default: soc-bkoff-deault-state { >> + pins = "gpio10"; >> + function = "gpio"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + sdc1_default: sdc1-default-state { >> + clk-pins { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <16>; >> + }; >> + >> + cmd-pins { >> + pins = "sdc1_cmd"; >> + bias-pull-up; >> + drive-strength = <16>; >> + }; >> + >> + data-pins { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <16>; >> + }; >> + >> + rclk-pins { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + }; >> + >> + sdc1_sleep: sdc1-sleep-state { >> + clk-pins { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + cmd-pins { >> + pins = "sdc1_cmd"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> + data-pins { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> + rclk-pins { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + }; >> + >> + ter_mi2s_active: ter-mi2s-active-state { >> + pins = "gpio63", "gpio64", "gpio65"; >> + function = "mi2s_2"; >> + }; >> +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 31aa54f0428c..8f0ffe35ca92 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -75,6 +75,7 @@ dtb-$(CONFIG_ARCH_QCOM) += qru1000-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += sa8155p-adp.dtb dtb-$(CONFIG_ARCH_QCOM) += sa8295p-adp.dtb dtb-$(CONFIG_ARCH_QCOM) += sa8540p-ride.dtb +dtb-$(CONFIG_ARCH_QCOM) += sc7180-acer-aspire1.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-idp.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1.dtb dtb-$(CONFIG_ARCH_QCOM) += sc7180-trogdor-coachz-r1-lte.dtb diff --git a/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts b/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts new file mode 100644 index 000000000000..2cd7c63d16f1 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts @@ -0,0 +1,867 @@ +// SPDX-License-Identifier: BSD-3-Clause + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> + +#include "sc7180.dtsi" + +#include "pm6150.dtsi" +#include "pm6150l.dtsi" + +/delete-node/ &tz_mem; +/delete-node/ &ipa_fw_mem; + +/ { + model = "Acer Aspire 1"; + compatible = "acer,aspire1", "qcom,sc7180"; + chassis-type = "laptop"; + + reserved-memory { + zap_mem: zap-shader@80840000 { + reg = <0 0x80840000 0 0x2000>; + no-map; + }; + + venus_mem: venus@85b00000 { + reg = <0 0x85b00000 0 0x500000>; + no-map; + }; + + mpss_mem: mpss@86000000 { + reg = <0x0 0x86000000 0x0 0x2000000>; + no-map; + }; + + adsp_mem: adsp@8e400000 { + reg = <0x0 0x8e400000 0x0 0x2800000>; + no-map; + }; + + wlan_mem: wlan@93900000 { + reg = <0x0 0x93900000 0x0 0x200000>; + no-map; + }; + }; + + aliases { + bluetooth0 = &bluetooth; + hsuart0 = &uart3; + serial0 = &uart8; + wifi0 = &wifi; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + max98357a: audio-codec-0 { + compatible = "maxim,max98357a"; + sdmode-gpios = <&tlmm 23 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&_sd_mode_default>; + pinctrl-names = "default"; + + #sound-dai-cells = <0>; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&sn65dsi86_bridge 1000000>; + enable-gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>; + + pinctrl-0 = <&soc_bkoff_default>; + pinctrl-names = "default"; + }; + + reg_brij_1p2: bridge-1p2-regulator { + compatible = "regulator-fixed"; + regulator-name = "brij_1p2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + + gpio = <&tlmm 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <®_edp_1p2_en_default>; + pinctrl-names = "default"; + }; + + reg_brij_1p8: bridge-regulator { + compatible = "regulator-fixed"; + regulator-name = "brij_1p8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + vin-supply = <&vreg_l8c_1p8>; + + gpio = <&tlmm 20 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <®_edp_1p8_en_default>; + pinctrl-names = "default"; + }; + + reg_codec_3p3: codec-regulator { + compatible = "regulator-fixed"; + regulator-name = "codec_3p3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 83 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <®_audio_en_default>; + pinctrl-names = "default"; + }; + + reg_lcm_3p3: panel-regulator { + compatible = "regulator-fixed"; + regulator-name = "lcm_3p3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + /* HACK: Display fails with + * + * *ERROR* Unexpected max rate (0x0); assuming 5.4 GHz + * *ERROR* Link training failed, link is off (-5) + * + * if the power to the panel was ever cut + */ + regulator-always-on; + + gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <®_lcm_en_default>; + pinctrl-names = "default"; + }; + + reg_tp_3p3: touchpad-regulator { + compatible = "regulator-fixed"; + regulator-name = "tp_3p3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>; + enable-active-high; + + pinctrl-0 = <®_tp_en_default>; + pinctrl-names = "default"; + }; +}; + +&camcc { status = "disabled"; }; + +&dsi0 { + vdda-supply = <&vreg_l3c_1p2>; + status = "okay"; +}; + +&dsi0_out { + remote-endpoint = <&sn65dsi86_in>; + data-lanes = <0 1 2 3>; +}; + +&dsi_phy { + vdds-supply = <&vreg_l4a_0p8>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <400000>; + status = "okay"; + + /* embedded-controller@76 */ +}; + +&i2c4 { + clock-frequency = <400000>; + status = "okay"; + + /* + * NOTE: DSDT defines two possible touchpads, other one is + * + * reg = <0x15>; + * hid-descr-addr = <0x1>; + */ + + touchpad@2c { + compatible = "hid-over-i2c"; + reg = <0x2c>; + hid-descr-addr = <0x20>; + + vdd-supply = <®_tp_3p3>; + + interrupts-extended = <&tlmm 94 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&hid_touchpad_default>; + pinctrl-names = "default"; + }; + + keyboard@3a { + compatible = "hid-over-i2c"; + reg = <0x3a>; + hid-descr-addr = <0x1>; + + interrupts-extended = <&tlmm 33 IRQ_TYPE_LEVEL_LOW>; + + pinctrl-0 = <&hid_keyboard_default>; + pinctrl-names = "default"; + + wakeup-source; + }; +}; + +&i2c9 { + clock-frequency = <400000>; + status = "okay"; + + alc5682: codec@1a { + compatible = "realtek,rt5682i"; + reg = <0x1a>; + + #sound-dai-cells = <1>; + + interrupt-parent = <&tlmm>; + /* + * This will get ignored because the interrupt type + * is set in rt5682.c. + */ + interrupts = <28 IRQ_TYPE_EDGE_BOTH>; + + pinctrl-0 = <&codec_irq_default>; + pinctrl-names = "default"; + + AVDD-supply = <&vreg_l15a_1p8>; + MICVDD-supply = <®_codec_3p3>; + VBAT-supply = <®_codec_3p3>; + + realtek,dmic1-data-pin = <1>; + realtek,dmic1-clk-pin = <1>; + realtek,jd-src = <1>; + }; +}; + +&i2c10 { + clock-frequency = <400000>; + status = "okay"; + + sn65dsi86_bridge: bridge@2c { + compatible = "ti,sn65dsi86"; + reg = <0x2c>; + gpio-controller; + #gpio-cells = <2>; + #pwm-cells = <1>; + + interrupt-parent = <&tlmm>; + interrupts = <11 IRQ_TYPE_LEVEL_HIGH>; + + enable-gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; + suspend-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + + pinctrl-0 = <&bridge_en_default>, + <&edp_bridge_irq_default>, + <&bridge_suspend_default>; + pinctrl-names = "default"; + + vpll-supply = <®_brij_1p8>; + vccio-supply = <®_brij_1p8>; + vcca-supply = <®_brij_1p2>; + vcc-supply = <®_brij_1p2>; + + clocks = <&rpmhcc RPMH_LN_BB_CLK3>; + clock-names = "refclk"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + sn65dsi86_in: endpoint { + remote-endpoint = <&dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + + sn65dsi86_out: endpoint { + data-lanes = <0 1>; + remote-endpoint = <&panel_in_edp>; + }; + }; + }; + + aux-bus { + panel: panel { + compatible = "edp-panel"; + power-supply = <®_lcm_3p3>; + backlight = <&backlight>; + + port { + panel_in_edp: endpoint { + remote-endpoint = <&sn65dsi86_out>; + }; + }; + }; + }; + }; +}; + +&gpu { + status = "okay"; + + zap-shader { + memory-region = <&zap_mem>; + firmware-name = "qcom/sc7180-acer-aspire1/qcdxkmsuc7180.mbn"; + }; +}; + +/* Seems like ADSP really insists on managing those itself */ +&lpasscc { status = "disabled"; }; +&lpass_hm { status = "disabled"; }; + +&mdp { + status = "okay"; +}; + +&mdss { + status = "okay"; +}; + +&pm6150_adc { + thermistor@4e { + reg = <ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; + + charger-thermistor@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + }; +}; + +&pm6150_adc_tm { + status = "okay"; + + charger-thermistor@0 { + reg = <0>; + io-channels = <&pm6150_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + thermistor@1 { + reg = <1>; + io-channels = <&pm6150_adc ADC5_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm6150_pon { status = "disabled"; }; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_mpss { + firmware-name = "qcom/sc7180-acer-aspire1/qcmpss7180_nm.mbn"; + status = "okay"; +}; + +&sdhc_1 { + pinctrl-0 = <&sdc1_default>; + pinctrl-1 = <&sdc1_sleep>; + pinctrl-names = "default", "sleep"; + vmmc-supply = <&vreg_l19a_2p9>; + vqmmc-supply = <&vreg_l12a_1p8>; + + status = "okay"; +}; + +&uart3 { + /delete-property/interrupts; + interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 41 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-1 = <&qup_uart3_sleep>; + pinctrl-names = "default", "sleep"; + + status = "okay"; + + bluetooth: bluetooth { + compatible = "qcom,wcn3991-bt"; + vddio-supply = <&vreg_l10a_1p8>; + vddxo-supply = <&vreg_l1c_1p8>; + vddrf-supply = <&vreg_l2c_1p3>; + vddch0-supply = <&vreg_l10c_3p3>; + max-speed = <3200000>; + }; +}; + +&uart8 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "host"; + #address-cells = <1>; + #size-cells = <0>; + + usb_hub_2_x: hub@1 { + compatible = "usbbda,5411"; + reg = <1>; + peer-hub = <&usb_hub_3_x>; + }; + + usb_hub_3_x: hub@2 { + compatible = "usbbda,411"; + reg = <2>; + peer-hub = <&usb_hub_2_x>; + }; +}; + +&usb_1_hsphy { + vdd-supply = <&vreg_l4a_0p8>; + vdda-pll-supply = <&vreg_l11a_1p8>; + vdda-phy-dpdm-supply = <&vreg_l17a_3p0>; + qcom,imp-res-offset-value = <8>; + qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>; + qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>; + qcom,bias-ctrl-value = <0x22>; + qcom,charge-ctrl-value = <3>; + qcom,hsdisc-trim-value = <0>; + + status = "okay"; +}; + +&usb_1_qmpphy { + vdda-phy-supply = <&vreg_l3c_1p2>; + vdda-pll-supply = <&vreg_l4a_0p8>; + status = "okay"; +}; + +&venus { + firmware-name = "qcom/sc7180-acer-aspire1/qcvss7180.mbn"; +}; + +&wifi { + vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>; + vdd-1.8-xo-supply = <&vreg_l1c_1p8>; + vdd-1.3-rfa-supply = <&vreg_l2c_1p3>; + vdd-3.3-ch0-supply = <&vreg_l10c_3p3>; + vdd-3.3-ch1-supply = <&vreg_l11c_3p3>; + status = "okay"; +}; + +&apps_rsc { + pm6150-rpmh-regulators { + compatible = "qcom,pm6150-rpmh-regulators"; + qcom,pmic-id = "a"; + + vreg_s1a_1p1: smps1 { + regulator-min-microvolt = <1128000>; + regulator-max-microvolt = <1128000>; + }; + + vreg_l4a_0p8: ldo4 { + regulator-min-microvolt = <824000>; + regulator-max-microvolt = <928000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9a_0p6: ldo9 { + regulator-min-microvolt = <488000>; + regulator-max-microvolt = <800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10a_1p8: ldo10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + + regulator-always-on; + regulator-boot-on; + }; + + vreg_l11a_1p8: ldo11 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12a_1p8: ldo12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13a_1p8: ldo13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14a_1p8: ldo14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15a_1p8: ldo15 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16a_2p7: ldo16 { + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17a_3p0: ldo17 { + regulator-min-microvolt = <2920000>; + regulator-max-microvolt = <3232000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18a_2p8: ldo18 { + regulator-min-microvolt = <2496000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l19a_2p9: ldo19 { + regulator-min-microvolt = <2960000>; + regulator-max-microvolt = <2960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + pm6150l-rpmh-regulators { + compatible = "qcom,pm6150l-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s8c_1p3: smps8 { + regulator-min-microvolt = <1120000>; + regulator-max-microvolt = <1408000>; + }; + + vreg_l1c_1p8: ldo1 { + regulator-min-microvolt = <1616000>; + regulator-max-microvolt = <1984000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c_1p3: ldo2 { + regulator-min-microvolt = <1168000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c_1p2: ldo3 { + regulator-min-microvolt = <1144000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c_1p8: ldo4 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l5c_1p8: ldo5 { + regulator-min-microvolt = <1648000>; + regulator-max-microvolt = <3304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l6c_2p9: ldo6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c_3p0: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3312000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>; + }; + + vreg_l8c_1p8: ldo8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c_2p9: ldo9 { + regulator-min-microvolt = <2952000>; + regulator-max-microvolt = <2952000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c_3p3: ldo10 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c_3p3: ldo11 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + }; +}; + +&qup_i2c2_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c4_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c9_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&qup_i2c10_default { + drive-strength = <2>; + + /* Has external pullup */ + bias-disable; +}; + +&tlmm { + /* + * The TZ seem to protect those because some boards can have + * fingerprint sensor connected to this range. Not connected + * on this board + */ + gpio-reserved-ranges = <58 5>; + + amp_sd_mode_default: amp-sd-mode-deault-state { + pins = "gpio23"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + bridge_en_default: bridge-en-default-state { + pins = "gpio51"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + bridge_suspend_default: bridge-suspend-default-state { + pins = "gpio22"; + function = "gpio"; + drive-strength = <16>; + bias-pull-up; + }; + + codec_irq_default: codec-irq-deault-state { + pins = "gpio28"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + edp_bridge_irq_default: edp-bridge-irq-default-state { + pins = "gpio11"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + hid_keyboard_default: hid-keyboard-default-state { + pins = "gpio33"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + hid_touchpad_default: hid-touchpad-default-state { + pins = "gpio94"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + qup_uart3_sleep: qup-uart3-sleep-state { + cts-pins { + /* + * Configure a pull-down on CTS to match the pull of + * the Bluetooth module. + */ + pins = "gpio38"; + function = "gpio"; + bias-pull-down; + }; + + rts-pins { + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + pins = "gpio39"; + function = "gpio"; + bias-pull-down; + }; + + tx-pins { + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + pins = "gpio40"; + function = "gpio"; + bias-pull-up; + }; + + rx-pins { + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ + pins = "gpio41"; + function = "gpio"; + bias-pull-up; + }; + }; + + reg_edp_1p2_en_default: reg-edp-1p2-en-deault-state { + pins = "gpio19"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + reg_edp_1p8_en_default: reg-edp-1p8-en-deault-state { + pins = "gpio20"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + reg_lcm_en_default: reg-lcm-en-deault-state { + pins = "gpio26"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + reg_audio_en_default: reg-audio-en-deault-state { + pins = "gpio83"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + reg_tp_en_default: reg-tp-en-deault-state { + pins = "gpio25"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + soc_bkoff_default: soc-bkoff-deault-state { + pins = "gpio10"; + function = "gpio"; + drive-strength = <16>; + bias-disable; + }; + + sdc1_default: sdc1-default-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <16>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <16>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + sdc1_sleep: sdc1-sleep-state { + clk-pins { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + cmd-pins { + pins = "sdc1_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + data-pins { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + rclk-pins { + pins = "sdc1_rclk"; + bias-pull-down; + }; + }; + + ter_mi2s_active: ter-mi2s-active-state { + pins = "gpio63", "gpio64", "gpio65"; + function = "mi2s_2"; + }; +};
Acer Aspire 1 is a WoA laptop based on Snapdragon 7c gen1 platform. The laptop design is similar to trogdor in the choice of primary components but the specifics on usage of those differ slightly. Add the devicetree for the laptop with support for most of the hardware present. Signed-off-by: Nikita Travkin <nikita@trvn.ru> --- Notable features absent from this patch: - Sound While the dedicated sound components are defined, since the ADSP must be used, sound requires additions of that remoteproc as well some extra "glue" to connect the i2s outputs to it. I was able to hack together some sound based on sm8250 stuff but it needs more work. - Embedded Controller The laptop has a dedicated EC that controls, notably, battery/charger and notifies the device about the USB-C DisplayPort HPD events. As per this patch, there is no battery status indication and external display support. Also, due to the EC defaults, the fn key is disabled. I have an experimental driver that implements all of that, which needs more work and will be submitted at a later date. --- arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sc7180-acer-aspire1.dts | 867 ++++++++++++++++++ 2 files changed, 868 insertions(+) create mode 100644 arch/arm64/boot/dts/qcom/sc7180-acer-aspire1.dts