diff mbox series

[14/14] arm64: dts: qcom: sdm845: Fix cheza qspi pin config

Message ID 20230323102605.14.I82951106ab8170f973a4c1c7d9b034655bbe2f60@changeid (mailing list archive)
State Accepted
Headers show
Series Control Quad SPI pinctrl better on Qualcomm Chromebooks | expand

Commit Message

Doug Anderson March 23, 2023, 5:30 p.m. UTC
Cheza's SPI flash hookups (qspi) are exactly the same as trogdor's.
Apply the same solution that's described in the patch ("arm64: dts:
qcom: sc7180: Fix trogdor qspi pin config")

Signed-off-by: Douglas Anderson <dianders@chromium.org>
---
I think cheza is only very lightly used today (it was never sold, but
there are various people still using the dev boards) and I'm not
personally setup to test this. It's fairly straightforward but has
only been compile-tested.

 arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi | 34 +++++++++++++++++-----
 arch/arm64/boot/dts/qcom/sdm845.dtsi       |  9 ++++--
 2 files changed, 34 insertions(+), 9 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
index 588165ee74b3..64ad8d1ed433 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-cheza.dtsi
@@ -319,8 +319,9 @@  venus_mem: memory@96000000 {
 
 &qspi {
 	status = "okay";
-	pinctrl-names = "default";
-	pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
+	pinctrl-names = "default", "sleep";
+	pinctrl-0 = <&qspi_clk>, <&qspi_cs0>, <&qspi_data0>, <&qspi_data1>;
+	pinctrl-1 = <&qspi_sleep>;
 
 	flash@0 {
 		compatible = "jedec,spi-nor";
@@ -995,16 +996,19 @@  &wifi {
 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 
 &qspi_cs0 {
-	bias-disable;
+	bias-disable;		/* External pullup */
 };
 
 &qspi_clk {
-	bias-disable;
+	bias-disable;		/* Rely on Cr50 internal pulldown */
 };
 
-&qspi_data01 {
-	/* High-Z when no transfers; nice to park the lines */
-	bias-pull-up;
+&qspi_data0 {
+	bias-disable;		/* Rely on Cr50 internal pulldown */
+};
+
+&qspi_data1 {
+	bias-pull-down;
 };
 
 &qup_i2c3_default {
@@ -1233,6 +1237,22 @@  pen_rst_l: pen-rst-l-state {
 		output-high;
 	};
 
+	qspi_sleep: qspi-sleep-state {
+		pins = "gpio90", "gpio91", "gpio92", "gpio95";
+
+		/*
+		 * When we're not actively transferring we want pins as GPIOs
+		 * with output disabled so that the quad SPI IP block stops
+		 * driving them. We rely on the normal pulls configured in
+		 * the active state and don't redefine them here. Also note
+		 * that we don't need the reverse (output-enable) in the
+		 * normal mode since the "output-enable" only matters for
+		 * GPIO function.
+		 */
+		function = "gpio";
+		output-disable;
+	};
+
 	sdc2_clk: sdc2-clk-state {
 		pins = "sdc2_clk";
 		bias-disable;
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi
index aafc7cc7edd8..dce2cb29347b 100644
--- a/arch/arm64/boot/dts/qcom/sdm845.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi
@@ -2758,8 +2758,13 @@  qspi_cs1: qspi-cs1-state {
 				function = "qspi_cs";
 			};
 
-			qspi_data01: qspi-data01-state {
-				pins = "gpio91", "gpio92";
+			qspi_data0: qspi-data0-state {
+				pins = "gpio91";
+				function = "qspi_data";
+			};
+
+			qspi_data1: qspi-data1-state {
+				pins = "gpio92";
 				function = "qspi_data";
 			};