| Message ID | 20230330165322.118279-3-me@dylanvanassche.be (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | dts: qcom: arm64: sdm845: SLPI DSP enablement | expand |
On 30.03.2023 18:53, Dylan Van Assche wrote: > Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through > an allocated memory region to load files from the host filesystem > such as sensor configuration files. > > Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar to > downstream, to allow userspace to communicate with the SLPI via the > FastRPC interface for initializing the sensors on the SLPI. > > Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> > --- > arch/arm64/boot/dts/qcom/sdm845.dtsi | 24 ++++++++++++++++++++++++ > 1 file changed, 24 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi > index 3b547cb7aeb8..8ea4944f3ad6 100644 > --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi > +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi > @@ -878,6 +878,14 @@ mdata_mem: mpss-metadata { > size = <0 0x4000>; > no-map; > }; > + > + fastrpc_mem: fastrpc { > + compatible = "shared-dma-pool"; > + reusable; Please move it last to get a nice reverse-Christmas-tree layout. > + alloc-ranges = <0 0x00000000 0 0xffffffff>; Would there be any issues with it starting over (1<<31 - 1)? > + alignment = <0 0x400000>; Please use 0x0 for the 0 here, as it's essentially reg.size with size-cells = 2 > + size = <0 0x1000000>; Ditto > + }; > }; > > adsp_pas: remoteproc-adsp { > @@ -3344,6 +3352,22 @@ glink-edge { > label = "dsps"; > qcom,remote-pid = <3>; > mboxes = <&apss_shared 24>; > + > + fastrpc { > + compatible = "qcom,fastrpc"; > + qcom,glink-channels = "fastrpcglink-apps-dsp"; > + label = "sdsp"; > + qcom,non-secure-domain; > + qcom,vmids = <0x3 0xF 0x5 0x6>; Please use the recently-introduced header and depend on (and make a patch atop) https://lore.kernel.org/linux-arm-msm/8685b710-b74d-556a-815d-0ffef2b0eeff@linaro.org/T/#t Konrad > + memory-region = <&fastrpc_mem>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + compute-cb@0 { > + compatible = "qcom,fastrpc-compute-cb"; > + reg = <0>; > + }; > + }; > }; > }; >
Hi Konrad, On Fri, 2023-03-31 at 04:03 +0200, Konrad Dybcio wrote: > > > On 30.03.2023 18:53, Dylan Van Assche wrote: > > Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through > > an allocated memory region to load files from the host filesystem > > such as sensor configuration files. > > > > Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar > > to > > downstream, to allow userspace to communicate with the SLPI via the > > FastRPC interface for initializing the sensors on the SLPI. > > > > Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> > > --- > > arch/arm64/boot/dts/qcom/sdm845.dtsi | 24 ++++++++++++++++++++++++ > > 1 file changed, 24 insertions(+) > > > > diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi > > b/arch/arm64/boot/dts/qcom/sdm845.dtsi > > index 3b547cb7aeb8..8ea4944f3ad6 100644 > > --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi > > +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi > > @@ -878,6 +878,14 @@ mdata_mem: mpss-metadata { > > size = <0 0x4000>; > > no-map; > > }; > > + > > + fastrpc_mem: fastrpc { > > + compatible = "shared-dma-pool"; > > + reusable; > Please move it last to get a nice reverse-Christmas-tree layout. > Will fix in v4. > > + alloc-ranges = <0 0x00000000 0 0xffffffff>; > Would there be any issues with it starting over (1<<31 - 1)? > You mean a bigger region then, like the whole CMA region then? AFAIK, the SLPI always use the same region expecting it to be in this range. However, I cannot confirm more, as I have no insights in the firmware running on there, this all comes from finding out what it exactly does on downstream. > > + alignment = <0 0x400000>; > Please use 0x0 for the 0 here, as it's essentially reg.size with > size-cells = 2 Will fix in v4. > > > + size = <0 0x1000000>; > Ditto Will fix in v4. > > > + }; > > }; > > > > adsp_pas: remoteproc-adsp { > > @@ -3344,6 +3352,22 @@ glink-edge { > > label = "dsps"; > > qcom,remote-pid = <3>; > > mboxes = <&apss_shared 24>; > > + > > + fastrpc { > > + compatible = > > "qcom,fastrpc"; > > + qcom,glink-channels = > > "fastrpcglink-apps-dsp"; > > + label = "sdsp"; > > + qcom,non-secure-domain; > > + qcom,vmids = <0x3 0xF 0x5 > > 0x6>; > Please use the recently-introduced header and depend on (and > make a patch atop) > > https://lore.kernel.org/linux-arm-msm/8685b710-b74d-556a-815d-0ffef2b0eeff@linaro.org/T/#t > > Konrad > > > + memory-region = > > <&fastrpc_mem>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + compute-cb@0 { > > + compatible = > > "qcom,fastrpc-compute-cb"; > > + reg = <0>; > > + }; > > + }; > > }; > > }; > > Kind regards, Dylan
On 31.03.2023 11:36, Dylan Van Assche wrote: > Hi Konrad, > > On Fri, 2023-03-31 at 04:03 +0200, Konrad Dybcio wrote: >> >> >> On 30.03.2023 18:53, Dylan Van Assche wrote: >>> Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through >>> an allocated memory region to load files from the host filesystem >>> such as sensor configuration files. >>> >>> Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar >>> to >>> downstream, to allow userspace to communicate with the SLPI via the >>> FastRPC interface for initializing the sensors on the SLPI. >>> >>> Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> >>> --- >>> arch/arm64/boot/dts/qcom/sdm845.dtsi | 24 ++++++++++++++++++++++++ >>> 1 file changed, 24 insertions(+) >>> >>> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi >>> b/arch/arm64/boot/dts/qcom/sdm845.dtsi >>> index 3b547cb7aeb8..8ea4944f3ad6 100644 >>> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi >>> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi >>> @@ -878,6 +878,14 @@ mdata_mem: mpss-metadata { >>> size = <0 0x4000>; >>> no-map; >>> }; >>> + >>> + fastrpc_mem: fastrpc { >>> + compatible = "shared-dma-pool"; >>> + reusable; >> Please move it last to get a nice reverse-Christmas-tree layout. >> > > Will fix in v4. > >>> + alloc-ranges = <0 0x00000000 0 0xffffffff>; >> Would there be any issues with it starting over (1<<31 - 1)? >> > > You mean a bigger region then, like the whole CMA region then? AFAIK, > the SLPI always use the same region expecting it to be in this range. > However, I cannot confirm more, as I have no insights in the firmware > running on there, this all comes from finding out what it exactly does > on downstream. I was asking about the <.. 0 0xfff.f> part specifically, as that means it can't be allocated above 4 gigs. But I guess it's just how qcom envisioned it. Also, please use 0x0 in alloc-ranges as well, this is all addresses/ reg sizes. Konrad > >>> + alignment = <0 0x400000>; >> Please use 0x0 for the 0 here, as it's essentially reg.size with >> size-cells = 2 > > Will fix in v4. > >> >>> + size = <0 0x1000000>; >> Ditto > > Will fix in v4. > >> >>> + }; >>> }; >>> >>> adsp_pas: remoteproc-adsp { >>> @@ -3344,6 +3352,22 @@ glink-edge { >>> label = "dsps"; >>> qcom,remote-pid = <3>; >>> mboxes = <&apss_shared 24>; >>> + >>> + fastrpc { >>> + compatible = >>> "qcom,fastrpc"; >>> + qcom,glink-channels = >>> "fastrpcglink-apps-dsp"; >>> + label = "sdsp"; >>> + qcom,non-secure-domain; >>> + qcom,vmids = <0x3 0xF 0x5 >>> 0x6>; >> Please use the recently-introduced header and depend on (and >> make a patch atop) >> >> https://lore.kernel.org/linux-arm-msm/8685b710-b74d-556a-815d-0ffef2b0eeff@linaro.org/T/#t >> >> Konrad >> >>> + memory-region = >>> <&fastrpc_mem>; >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + compute-cb@0 { >>> + compatible = >>> "qcom,fastrpc-compute-cb"; >>> + reg = <0>; >>> + }; >>> + }; >>> }; >>> }; >>> > > Kind regards, > Dylan
On Fri, 2023-03-31 at 14:20 +0200, Konrad Dybcio wrote: > > > On 31.03.2023 11:36, Dylan Van Assche wrote: > > Hi Konrad, > > > > On Fri, 2023-03-31 at 04:03 +0200, Konrad Dybcio wrote: > > > > > > > > > On 30.03.2023 18:53, Dylan Van Assche wrote: > > > > Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC > > > > through > > > > an allocated memory region to load files from the host > > > > filesystem > > > > such as sensor configuration files. > > > > > > > > Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, > > > > similar > > > > to > > > > downstream, to allow userspace to communicate with the SLPI via > > > > the > > > > FastRPC interface for initializing the sensors on the SLPI. > > > > > > > > Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> > > > > --- > > > > arch/arm64/boot/dts/qcom/sdm845.dtsi | 24 > > > > ++++++++++++++++++++++++ > > > > 1 file changed, 24 insertions(+) > > > > > > > > diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi > > > > b/arch/arm64/boot/dts/qcom/sdm845.dtsi > > > > index 3b547cb7aeb8..8ea4944f3ad6 100644 > > > > --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi > > > > +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi > > > > @@ -878,6 +878,14 @@ mdata_mem: mpss-metadata { > > > > size = <0 0x4000>; > > > > no-map; > > > > }; > > > > + > > > > + fastrpc_mem: fastrpc { > > > > + compatible = "shared-dma-pool"; > > > > + reusable; > > > Please move it last to get a nice reverse-Christmas-tree layout. > > > > > > > Will fix in v4. > > > > > > + alloc-ranges = <0 0x00000000 0 > > > > 0xffffffff>; > > > Would there be any issues with it starting over (1<<31 - 1)? > > > > > > > You mean a bigger region then, like the whole CMA region then? > > AFAIK, > > the SLPI always use the same region expecting it to be in this > > range. > > However, I cannot confirm more, as I have no insights in the > > firmware > > running on there, this all comes from finding out what it exactly > > does > > on downstream. > I was asking about the <.. 0 0xfff.f> part specifically, as that > means > it can't be allocated above 4 gigs. But I guess it's just how qcom > envisioned it. > I think it is limited by qcom, but I cannot be entirely sure :) In any case, for v4, do I keep 0xffffffff? > Also, please use 0x0 in alloc-ranges as well, this is all addresses/ > reg sizes. > > Konrad Yes, will use 0x0 instead of 0. Dylan > > > > > > + alignment = <0 0x400000>; > > > Please use 0x0 for the 0 here, as it's essentially reg.size with > > > size-cells = 2 > > > > Will fix in v4. > > > > > > > > > + size = <0 0x1000000>; > > > Ditto > > > > Will fix in v4. > > > > > > > > > + }; > > > > }; > > > > > > > > adsp_pas: remoteproc-adsp { > > > > @@ -3344,6 +3352,22 @@ glink-edge { > > > > label = "dsps"; > > > > qcom,remote-pid = <3>; > > > > mboxes = <&apss_shared 24>; > > > > + > > > > + fastrpc { > > > > + compatible = > > > > "qcom,fastrpc"; > > > > + qcom,glink-channels = > > > > "fastrpcglink-apps-dsp"; > > > > + label = "sdsp"; > > > > + qcom,non-secure-domain; > > > > + qcom,vmids = <0x3 0xF > > > > 0x5 > > > > 0x6>; > > > Please use the recently-introduced header and depend on (and > > > make a patch atop) > > > > > > https://lore.kernel.org/linux-arm-msm/8685b710-b74d-556a-815d-0ffef2b0eeff@linaro.org/T/#t > > > > > > Konrad > > > > > > > + memory-region = > > > > <&fastrpc_mem>; > > > > + #address-cells = <1>; > > > > + #size-cells = <0>; > > > > + > > > > + compute-cb@0 { > > > > + compatible = > > > > "qcom,fastrpc-compute-cb"; > > > > + reg = <0>; > > > > + }; > > > > + }; > > > > }; > > > > }; > > > > > > > > Kind regards, > > Dylan
On 31.03.2023 15:14, Dylan Van Assche wrote: > On Fri, 2023-03-31 at 14:20 +0200, Konrad Dybcio wrote: >> >> >> On 31.03.2023 11:36, Dylan Van Assche wrote: >>> Hi Konrad, >>> >>> On Fri, 2023-03-31 at 04:03 +0200, Konrad Dybcio wrote: >>>> >>>> >>>> On 30.03.2023 18:53, Dylan Van Assche wrote: >>>>> Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC >>>>> through >>>>> an allocated memory region to load files from the host >>>>> filesystem >>>>> such as sensor configuration files. >>>>> >>>>> Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, >>>>> similar >>>>> to >>>>> downstream, to allow userspace to communicate with the SLPI via >>>>> the >>>>> FastRPC interface for initializing the sensors on the SLPI. >>>>> >>>>> Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> >>>>> --- >>>>> arch/arm64/boot/dts/qcom/sdm845.dtsi | 24 >>>>> ++++++++++++++++++++++++ >>>>> 1 file changed, 24 insertions(+) >>>>> >>>>> diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi >>>>> b/arch/arm64/boot/dts/qcom/sdm845.dtsi >>>>> index 3b547cb7aeb8..8ea4944f3ad6 100644 >>>>> --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi >>>>> +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi >>>>> @@ -878,6 +878,14 @@ mdata_mem: mpss-metadata { >>>>> size = <0 0x4000>; >>>>> no-map; >>>>> }; >>>>> + >>>>> + fastrpc_mem: fastrpc { >>>>> + compatible = "shared-dma-pool"; >>>>> + reusable; >>>> Please move it last to get a nice reverse-Christmas-tree layout. >>>> >>> >>> Will fix in v4. >>> >>>>> + alloc-ranges = <0 0x00000000 0 >>>>> 0xffffffff>; >>>> Would there be any issues with it starting over (1<<31 - 1)? >>>> >>> >>> You mean a bigger region then, like the whole CMA region then? >>> AFAIK, >>> the SLPI always use the same region expecting it to be in this >>> range. >>> However, I cannot confirm more, as I have no insights in the >>> firmware >>> running on there, this all comes from finding out what it exactly >>> does >>> on downstream. >> I was asking about the <.. 0 0xfff.f> part specifically, as that >> means >> it can't be allocated above 4 gigs. But I guess it's just how qcom >> envisioned it. >> > > I think it is limited by qcom, but I cannot be entirely sure :) > In any case, for v4, do I keep 0xffffffff? Yep, let's not stray into the unknown.. Konrad > >> Also, please use 0x0 in alloc-ranges as well, this is all addresses/ >> reg sizes. >> >> Konrad > > Yes, will use 0x0 instead of 0. > > Dylan > >>> >>>>> + alignment = <0 0x400000>; >>>> Please use 0x0 for the 0 here, as it's essentially reg.size with >>>> size-cells = 2 >>> >>> Will fix in v4. >>> >>>> >>>>> + size = <0 0x1000000>; >>>> Ditto >>> >>> Will fix in v4. >>> >>>> >>>>> + }; >>>>> }; >>>>> >>>>> adsp_pas: remoteproc-adsp { >>>>> @@ -3344,6 +3352,22 @@ glink-edge { >>>>> label = "dsps"; >>>>> qcom,remote-pid = <3>; >>>>> mboxes = <&apss_shared 24>; >>>>> + >>>>> + fastrpc { >>>>> + compatible = >>>>> "qcom,fastrpc"; >>>>> + qcom,glink-channels = >>>>> "fastrpcglink-apps-dsp"; >>>>> + label = "sdsp"; >>>>> + qcom,non-secure-domain; >>>>> + qcom,vmids = <0x3 0xF >>>>> 0x5 >>>>> 0x6>; >>>> Please use the recently-introduced header and depend on (and >>>> make a patch atop) >>>> >>>> https://lore.kernel.org/linux-arm-msm/8685b710-b74d-556a-815d-0ffef2b0eeff@linaro.org/T/#t >>>> >>>> Konrad >>>> >>>>> + memory-region = >>>>> <&fastrpc_mem>; >>>>> + #address-cells = <1>; >>>>> + #size-cells = <0>; >>>>> + >>>>> + compute-cb@0 { >>>>> + compatible = >>>>> "qcom,fastrpc-compute-cb"; >>>>> + reg = <0>; >>>>> + }; >>>>> + }; >>>>> }; >>>>> }; >>>>> >>> >>> Kind regards, >>> Dylan >
diff --git a/arch/arm64/boot/dts/qcom/sdm845.dtsi b/arch/arm64/boot/dts/qcom/sdm845.dtsi index 3b547cb7aeb8..8ea4944f3ad6 100644 --- a/arch/arm64/boot/dts/qcom/sdm845.dtsi +++ b/arch/arm64/boot/dts/qcom/sdm845.dtsi @@ -878,6 +878,14 @@ mdata_mem: mpss-metadata { size = <0 0x4000>; no-map; }; + + fastrpc_mem: fastrpc { + compatible = "shared-dma-pool"; + reusable; + alloc-ranges = <0 0x00000000 0 0xffffffff>; + alignment = <0 0x400000>; + size = <0 0x1000000>; + }; }; adsp_pas: remoteproc-adsp { @@ -3344,6 +3352,22 @@ glink-edge { label = "dsps"; qcom,remote-pid = <3>; mboxes = <&apss_shared 24>; + + fastrpc { + compatible = "qcom,fastrpc"; + qcom,glink-channels = "fastrpcglink-apps-dsp"; + label = "sdsp"; + qcom,non-secure-domain; + qcom,vmids = <0x3 0xF 0x5 0x6>; + memory-region = <&fastrpc_mem>; + #address-cells = <1>; + #size-cells = <0>; + + compute-cb@0 { + compatible = "qcom,fastrpc-compute-cb"; + reg = <0>; + }; + }; }; };
Qualcomm SDM845 SoC features a SLPI DSP which uses FastRPC through an allocated memory region to load files from the host filesystem such as sensor configuration files. Add a FastRPC node at /dev/fastrpc-sdsp and a DMA region, similar to downstream, to allow userspace to communicate with the SLPI via the FastRPC interface for initializing the sensors on the SLPI. Signed-off-by: Dylan Van Assche <me@dylanvanassche.be> --- arch/arm64/boot/dts/qcom/sdm845.dtsi | 24 ++++++++++++++++++++++++ 1 file changed, 24 insertions(+)