diff mbox series

[v2] arm64: dts: qcom: msm8953: Add BLSP DMAs for I2C

Message ID 20230422-msm8953-blsp-dma-v2-1-076134481b1b@z3ntu.xyz (mailing list archive)
State Changes Requested
Headers show
Series [v2] arm64: dts: qcom: msm8953: Add BLSP DMAs for I2C | expand

Commit Message

Luca Weiss May 23, 2023, 8:36 p.m. UTC 
MSM8953 has two DMA controllers for the various I2C, SPI and UART
busses. Add the nodes and configure all the I2C nodes so that the driver
can use the DMA.

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
---
Changes in v2:
- Fix subject line, add "msm8953" (thanks Alexey)
- Pick up tags
- Link to v1: https://lore.kernel.org/r/20230422-msm8953-blsp-dma-v1-1-0024801bb587@z3ntu.xyz
---
 arch/arm64/boot/dts/qcom/msm8953.dtsi | 48 +++++++++++++++++++++++++++++++++++
 1 file changed, 48 insertions(+)


---
base-commit: 99e988f2970e39d0859908c3adc2ff689172496a
change-id: 20230422-msm8953-blsp-dma-1174277859f2

Best regards,

Comments

Stephan Gerhold May 24, 2023, 6:14 p.m. UTC | #1 
On Tue, May 23, 2023 at 10:36:49PM +0200, Luca Weiss wrote:
> MSM8953 has two DMA controllers for the various I2C, SPI and UART
> busses. Add the nodes and configure all the I2C nodes so that the driver
> can use the DMA.
> 
> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
> Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
> ---
> Changes in v2:
> - Fix subject line, add "msm8953" (thanks Alexey)
> - Pick up tags
> - Link to v1: https://lore.kernel.org/r/20230422-msm8953-blsp-dma-v1-1-0024801bb587@z3ntu.xyz
> ---
>  arch/arm64/boot/dts/qcom/msm8953.dtsi | 48 +++++++++++++++++++++++++++++++++++
>  1 file changed, 48 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
> index 602cb188a635..c9b589353918 100644
> --- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
> +++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
> @@ -1274,6 +1274,19 @@ opp-200000000 {
>  			};
>  		};
>  
> +		blsp1_dma: dma-controller@7884000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07884000 0x1f000>;
> +			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			num-channels = <12>;
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +			qcom,num-ees = <4>;

You can omit num-channels/qcom,num-ees here if you have a clock.

"dmaengine: qcom: bam_dma: allow omitting num-{channels,ees}" [1] helps
with doing this, although it also works without the patch. (The patch
just avoids a non-critical error in dmesg...)

[1]: https://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine.git/commit/?id=8975dd41a9dbca3b47f7b8dac5bc4dfb23011000

> +		blsp2_dma: dma-controller@7ac4000 {
> +			compatible = "qcom,bam-v1.7.0";
> +			reg = <0x07ac4000 0x1f000>;
> +			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
> +			clock-names = "bam_clk";
> +			num-channels = <12>;
> +			#dma-cells = <1>;
> +			qcom,ee = <0>;
> +			qcom,num-ees = <4>;

Same here.

Thanks,
Stephan
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/msm8953.dtsi b/arch/arm64/boot/dts/qcom/msm8953.dtsi
index 602cb188a635..c9b589353918 100644
--- a/arch/arm64/boot/dts/qcom/msm8953.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8953.dtsi
@@ -1274,6 +1274,19 @@  opp-200000000 {
 			};
 		};
 
+		blsp1_dma: dma-controller@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x1f000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			num-channels = <12>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,num-ees = <4>;
+			qcom,controlled-remotely;
+		};
+
 		uart_0: serial@78af000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x078af000 0x200>;
@@ -1292,6 +1305,8 @@  i2c_1: i2c@78b5000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP1_QUP1_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
+			dmas = <&blsp1_dma 4>, <&blsp1_dma 5>;
+			dma-names = "tx", "rx";
 
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_1_default>;
@@ -1310,6 +1325,8 @@  i2c_2: i2c@78b6000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
+			dmas = <&blsp1_dma 6>, <&blsp1_dma 7>;
+			dma-names = "tx", "rx";
 
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_2_default>;
@@ -1328,6 +1345,9 @@  i2c_3: i2c@78b7000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
+			dmas = <&blsp1_dma 8>, <&blsp1_dma 9>;
+			dma-names = "tx", "rx";
+
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_3_default>;
 			pinctrl-1 = <&i2c_3_sleep>;
@@ -1345,6 +1365,9 @@  i2c_4: i2c@78b8000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP1_AHB_CLK>;
+			dmas = <&blsp2_dma 10>, <&blsp2_dma 11>;
+			dma-names = "tx", "rx";
+
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_4_default>;
 			pinctrl-1 = <&i2c_4_sleep>;
@@ -1355,6 +1378,19 @@  i2c_4: i2c@78b8000 {
 			status = "disabled";
 		};
 
+		blsp2_dma: dma-controller@7ac4000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07ac4000 0x1f000>;
+			interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP2_AHB_CLK>;
+			clock-names = "bam_clk";
+			num-channels = <12>;
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+			qcom,num-ees = <4>;
+			qcom,controlled-remotely;
+		};
+
 		i2c_5: i2c@7af5000 {
 			compatible = "qcom,i2c-qup-v2.2.1";
 			reg = <0x07af5000 0x600>;
@@ -1362,6 +1398,9 @@  i2c_5: i2c@7af5000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP2_AHB_CLK>;
+			dmas = <&blsp2_dma 4>, <&blsp2_dma 5>;
+			dma-names = "tx", "rx";
+
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_5_default>;
 			pinctrl-1 = <&i2c_5_sleep>;
@@ -1379,6 +1418,9 @@  i2c_6: i2c@7af6000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP2_QUP2_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP2_AHB_CLK>;
+			dmas = <&blsp2_dma 6>, <&blsp2_dma 7>;
+			dma-names = "tx", "rx";
+
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_6_default>;
 			pinctrl-1 = <&i2c_6_sleep>;
@@ -1396,6 +1438,9 @@  i2c_7: i2c@7af7000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP2_QUP3_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP2_AHB_CLK>;
+			dmas = <&blsp2_dma 8>, <&blsp2_dma 9>;
+			dma-names = "tx", "rx";
+
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_7_default>;
 			pinctrl-1 = <&i2c_7_sleep>;
@@ -1413,6 +1458,9 @@  i2c_8: i2c@7af8000 {
 			clock-names = "core", "iface";
 			clocks = <&gcc GCC_BLSP2_QUP4_I2C_APPS_CLK>,
 				 <&gcc GCC_BLSP2_AHB_CLK>;
+			dmas = <&blsp2_dma 10>, <&blsp2_dma 11>;
+			dma-names = "tx", "rx";
+
 			pinctrl-names = "default", "sleep";
 			pinctrl-0 = <&i2c_8_default>;
 			pinctrl-1 = <&i2c_8_sleep>;