diff mbox series

[V3] arm64: dts: qcom: ipq9574: add few device nodes

Message ID 20230517072806.13170-1-quic_kathirav@quicinc.com (mailing list archive)
State Accepted
Headers show
Series [V3] arm64: dts: qcom: ipq9574: add few device nodes | expand

Commit Message

Kathiravan Thirumoorthy May 17, 2023, 7:28 a.m. UTC 
Add QUP(SPI / I2C) peripheral, PRNG, WDOG and the remaining UART nodes.
While at it, enable the SPI NOR in RDP433 board.

Signed-off-by: Kathiravan T <quic_kathirav@quicinc.com>
---
Changed since V2:
	- V2 didn't apply properly on below series, fixed it now
Changes since V1:
	- Dropped the WDT binding patch, since it is already part of
	  linux-next
	- Rebased on the below series
	  https://lore.kernel.org/linux-arm-msm/75a408c2-3d41-95a3-5c48-a68c84ba4f57@quicinc.com/T/#t

 arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts |  21 ++
 arch/arm64/boot/dts/qcom/ipq9574.dtsi       | 202 ++++++++++++++++++++
 2 files changed, 223 insertions(+)

Comments

Bjorn Andersson May 25, 2023, 4:54 a.m. UTC | #1 
On Wed, 17 May 2023 12:58:06 +0530, Kathiravan T wrote:
> Add QUP(SPI / I2C) peripheral, PRNG, WDOG and the remaining UART nodes.
> While at it, enable the SPI NOR in RDP433 board.
> 
> 

Applied, thanks!

[1/1] arm64: dts: qcom: ipq9574: add few device nodes
      commit: 9ef42640504e09ecc79530b6e532ebf48305516b

Best regards,
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
index 2ce8e09e7565..7be578017bf7 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
+++ b/arch/arm64/boot/dts/qcom/ipq9574-rdp433.dts
@@ -29,6 +29,20 @@ 
 	status = "okay";
 };
 
+&blsp1_spi0 {
+	pinctrl-0 = <&spi_0_pins>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	flash@0 {
+		compatible = "micron,n25q128a11", "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		spi-max-frequency = <50000000>;
+	};
+};
+
 &sdhc_1 {
 	pinctrl-0 = <&sdc_default_state>;
 	pinctrl-names = "default";
@@ -77,6 +91,13 @@ 
 			bias-pull-down;
 		};
 	};
+
+	spi_0_pins: spi-0-state {
+		pins = "gpio11", "gpio12", "gpio13", "gpio14";
+		function = "blsp0_spi";
+		drive-strength = <8>;
+		bias-disable;
+	};
 };
 
 &xo_board_clk {
diff --git a/arch/arm64/boot/dts/qcom/ipq9574.dtsi b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
index ccf70bafabab..fea15f3cf910 100644
--- a/arch/arm64/boot/dts/qcom/ipq9574.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq9574.dtsi
@@ -116,6 +116,13 @@ 
 		#size-cells = <1>;
 		ranges = <0 0 0 0xffffffff>;
 
+		rng: rng@e3000 {
+			compatible = "qcom,prng-ee";
+			reg = <0x000e3000 0x1000>;
+			clocks = <&gcc GCC_PRNG_AHB_CLK>;
+			clock-names = "core";
+		};
+
 		tlmm: pinctrl@1000000 {
 			compatible = "qcom,ipq9574-tlmm";
 			reg = <0x01000000 0x300000>;
@@ -178,6 +185,36 @@ 
 			status = "disabled";
 		};
 
+		blsp_dma: dma-controller@7884000 {
+			compatible = "qcom,bam-v1.7.0";
+			reg = <0x07884000 0x2b000>;
+			interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "bam_clk";
+			#dma-cells = <1>;
+			qcom,ee = <0>;
+		};
+
+		blsp1_uart0: serial@78af000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078af000 0x200>;
+			interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart1: serial@78b0000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b0000 0x200>;
+			interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
 		blsp1_uart2: serial@78b1000 {
 			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
 			reg = <0x078b1000 0x200>;
@@ -188,6 +225,163 @@ 
 			status = "disabled";
 		};
 
+		blsp1_uart3: serial@78b2000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b2000 0x200>;
+			interrupts = <GIC_SPI 307 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART4_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart4: serial@78b3000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b3000 0x200>;
+			interrupts = <GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART5_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_uart5: serial@78b4000 {
+			compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm";
+			reg = <0x078b4000 0x200>;
+			interrupts = <GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_UART6_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			status = "disabled";
+		};
+
+		blsp1_spi0: spi@78b5000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b5000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP1_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 12>, <&blsp_dma 13>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_i2c1: i2c@78b6000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b6000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_spi1: spi@78b6000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b6000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP2_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 14>, <&blsp_dma 15>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_i2c2: i2c@78b7000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b7000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_spi2: spi@78b7000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b7000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 16>, <&blsp_dma 17>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_i2c3: i2c@78b8000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b8000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 18>, <&blsp_dma 19>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_spi3: spi@78b8000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b8000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			spi-max-frequency = <50000000>;
+			clocks = <&gcc GCC_BLSP1_QUP4_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 18>, <&blsp_dma 19>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_i2c4: i2c@78b9000 {
+			compatible = "qcom,i2c-qup-v2.2.1";
+			reg = <0x078b9000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_I2C_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 20>, <&blsp_dma 21>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		blsp1_spi4: spi@78b9000 {
+			compatible = "qcom,spi-qup-v2.2.1";
+			reg = <0x078b9000 0x600>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&gcc GCC_BLSP1_QUP5_SPI_APPS_CLK>,
+				 <&gcc GCC_BLSP1_AHB_CLK>;
+			clock-names = "core", "iface";
+			dmas = <&blsp_dma 20>, <&blsp_dma 21>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
 		intc: interrupt-controller@b000000 {
 			compatible = "qcom,msm-qgic2";
 			reg = <0x0b000000 0x1000>,  /* GICD */
@@ -220,6 +414,14 @@ 
 			};
 		};
 
+		watchdog: watchdog@b017000 {
+			compatible = "qcom,apss-wdt-ipq9574", "qcom,kpss-wdt";
+			reg = <0x0b017000 0x1000>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>;
+			clocks = <&sleep_clk>;
+			timeout-sec = <30>;
+		};
+
 		timer@b120000 {
 			compatible = "arm,armv7-timer-mem";
 			reg = <0x0b120000 0x1000>;