| Message ID | 20230605115607.921308-1-abel.vesa@linaro.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | regulator: qcom-rpmh: Fix regulators for PM8550 | expand |
On 6/5/2023 5:26 PM, Abel Vesa wrote: > The PM8550 uses only NLDOs 515 and the LDO 6 through 8 are low voltage > type, so fix accordingly. I was seeing a bunch of LDO initialization's fail while bringing up an upcoming SoC/Board which uses these same set of PMIC's, some of those are fixed with this patch, but I still have a couple more failing due to the voltage that I try to init them to being out of range based on their voltage range, can you pls check if those are of the right type? The ones now failing are, ldo12 from pm8550 and smps4 from pm8550ve. > > Fixes: e6e3776d682d ("regulator: qcom-rpmh: Add support for PM8550 regulators") > Signed-off-by: Abel Vesa <abel.vesa@linaro.org> > --- > drivers/regulator/qcom-rpmh-regulator.c | 30 ++++++++++++------------- > 1 file changed, 15 insertions(+), 15 deletions(-) > > diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c > index b0a58c62b1e2..f3b280af0773 100644 > --- a/drivers/regulator/qcom-rpmh-regulator.c > +++ b/drivers/regulator/qcom-rpmh-regulator.c > @@ -1057,21 +1057,21 @@ static const struct rpmh_vreg_init_data pm8450_vreg_data[] = { > }; > > static const struct rpmh_vreg_init_data pm8550_vreg_data[] = { > - RPMH_VREG("ldo1", "ldo%s1", &pmic5_pldo, "vdd-l1-l4-l10"), > + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo515, "vdd-l1-l4-l10"), > RPMH_VREG("ldo2", "ldo%s2", &pmic5_pldo, "vdd-l2-l13-l14"), > - RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3"), > - RPMH_VREG("ldo4", "ldo%s4", &pmic5_nldo, "vdd-l1-l4-l10"), > + RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo515, "vdd-l3"), > + RPMH_VREG("ldo4", "ldo%s4", &pmic5_nldo515, "vdd-l1-l4-l10"), > RPMH_VREG("ldo5", "ldo%s5", &pmic5_pldo, "vdd-l5-l16"), > - RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo_lv, "vdd-l6-l7"), > - RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo_lv, "vdd-l6-l7"), > - RPMH_VREG("ldo8", "ldo%s8", &pmic5_pldo_lv, "vdd-l8-l9"), > + RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l6-l7"), > + RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo, "vdd-l6-l7"), > + RPMH_VREG("ldo8", "ldo%s8", &pmic5_pldo, "vdd-l8-l9"), > RPMH_VREG("ldo9", "ldo%s9", &pmic5_pldo, "vdd-l8-l9"), > - RPMH_VREG("ldo10", "ldo%s10", &pmic5_nldo, "vdd-l1-l4-l10"), > - RPMH_VREG("ldo11", "ldo%s11", &pmic5_nldo, "vdd-l11"), > + RPMH_VREG("ldo10", "ldo%s10", &pmic5_nldo515, "vdd-l1-l4-l10"), > + RPMH_VREG("ldo11", "ldo%s11", &pmic5_nldo515, "vdd-l11"), > RPMH_VREG("ldo12", "ldo%s12", &pmic5_pldo, "vdd-l12"), > RPMH_VREG("ldo13", "ldo%s13", &pmic5_pldo, "vdd-l2-l13-l14"), > RPMH_VREG("ldo14", "ldo%s14", &pmic5_pldo, "vdd-l2-l13-l14"), > - RPMH_VREG("ldo15", "ldo%s15", &pmic5_pldo, "vdd-l15"), > + RPMH_VREG("ldo15", "ldo%s15", &pmic5_nldo515, "vdd-l15"), > RPMH_VREG("ldo16", "ldo%s16", &pmic5_pldo, "vdd-l5-l16"), > RPMH_VREG("ldo17", "ldo%s17", &pmic5_pldo, "vdd-l17"), > RPMH_VREG("bob1", "bob%s1", &pmic5_bob, "vdd-bob1"), > @@ -1086,9 +1086,9 @@ static const struct rpmh_vreg_init_data pm8550vs_vreg_data[] = { > RPMH_VREG("smps4", "smp%s4", &pmic5_ftsmps525_lv, "vdd-s4"), > RPMH_VREG("smps5", "smp%s5", &pmic5_ftsmps525_lv, "vdd-s5"), > RPMH_VREG("smps6", "smp%s6", &pmic5_ftsmps525_mv, "vdd-s6"), > - RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo, "vdd-l1"), > - RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo, "vdd-l2"), > - RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3"), > + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo515, "vdd-l1"), > + RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo515, "vdd-l2"), > + RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo515, "vdd-l3"), > {} > }; > > @@ -1101,9 +1101,9 @@ static const struct rpmh_vreg_init_data pm8550ve_vreg_data[] = { > RPMH_VREG("smps6", "smp%s6", &pmic5_ftsmps525_lv, "vdd-s6"), > RPMH_VREG("smps7", "smp%s7", &pmic5_ftsmps525_lv, "vdd-s7"), > RPMH_VREG("smps8", "smp%s8", &pmic5_ftsmps525_lv, "vdd-s8"), > - RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo, "vdd-l1"), > - RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo, "vdd-l2"), > - RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3"), > + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo515, "vdd-l1"), > + RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo515, "vdd-l2"), > + RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo515, "vdd-l3"), > {} > }; >
On Mon, 05 Jun 2023 14:56:07 +0300, Abel Vesa wrote: > The PM8550 uses only NLDOs 515 and the LDO 6 through 8 are low voltage > type, so fix accordingly. > > Applied to https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git for-next Thanks! [1/1] regulator: qcom-rpmh: Fix regulators for PM8550 commit: b00de0000a69579f4d730077fe3ea8ca31404255 All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted. You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed. If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced. Please add any relevant lists and maintainers to the CCs when replying to this mail. Thanks, Mark
diff --git a/drivers/regulator/qcom-rpmh-regulator.c b/drivers/regulator/qcom-rpmh-regulator.c index b0a58c62b1e2..f3b280af0773 100644 --- a/drivers/regulator/qcom-rpmh-regulator.c +++ b/drivers/regulator/qcom-rpmh-regulator.c @@ -1057,21 +1057,21 @@ static const struct rpmh_vreg_init_data pm8450_vreg_data[] = { }; static const struct rpmh_vreg_init_data pm8550_vreg_data[] = { - RPMH_VREG("ldo1", "ldo%s1", &pmic5_pldo, "vdd-l1-l4-l10"), + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo515, "vdd-l1-l4-l10"), RPMH_VREG("ldo2", "ldo%s2", &pmic5_pldo, "vdd-l2-l13-l14"), - RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3"), - RPMH_VREG("ldo4", "ldo%s4", &pmic5_nldo, "vdd-l1-l4-l10"), + RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo515, "vdd-l3"), + RPMH_VREG("ldo4", "ldo%s4", &pmic5_nldo515, "vdd-l1-l4-l10"), RPMH_VREG("ldo5", "ldo%s5", &pmic5_pldo, "vdd-l5-l16"), - RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo_lv, "vdd-l6-l7"), - RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo_lv, "vdd-l6-l7"), - RPMH_VREG("ldo8", "ldo%s8", &pmic5_pldo_lv, "vdd-l8-l9"), + RPMH_VREG("ldo6", "ldo%s6", &pmic5_pldo, "vdd-l6-l7"), + RPMH_VREG("ldo7", "ldo%s7", &pmic5_pldo, "vdd-l6-l7"), + RPMH_VREG("ldo8", "ldo%s8", &pmic5_pldo, "vdd-l8-l9"), RPMH_VREG("ldo9", "ldo%s9", &pmic5_pldo, "vdd-l8-l9"), - RPMH_VREG("ldo10", "ldo%s10", &pmic5_nldo, "vdd-l1-l4-l10"), - RPMH_VREG("ldo11", "ldo%s11", &pmic5_nldo, "vdd-l11"), + RPMH_VREG("ldo10", "ldo%s10", &pmic5_nldo515, "vdd-l1-l4-l10"), + RPMH_VREG("ldo11", "ldo%s11", &pmic5_nldo515, "vdd-l11"), RPMH_VREG("ldo12", "ldo%s12", &pmic5_pldo, "vdd-l12"), RPMH_VREG("ldo13", "ldo%s13", &pmic5_pldo, "vdd-l2-l13-l14"), RPMH_VREG("ldo14", "ldo%s14", &pmic5_pldo, "vdd-l2-l13-l14"), - RPMH_VREG("ldo15", "ldo%s15", &pmic5_pldo, "vdd-l15"), + RPMH_VREG("ldo15", "ldo%s15", &pmic5_nldo515, "vdd-l15"), RPMH_VREG("ldo16", "ldo%s16", &pmic5_pldo, "vdd-l5-l16"), RPMH_VREG("ldo17", "ldo%s17", &pmic5_pldo, "vdd-l17"), RPMH_VREG("bob1", "bob%s1", &pmic5_bob, "vdd-bob1"), @@ -1086,9 +1086,9 @@ static const struct rpmh_vreg_init_data pm8550vs_vreg_data[] = { RPMH_VREG("smps4", "smp%s4", &pmic5_ftsmps525_lv, "vdd-s4"), RPMH_VREG("smps5", "smp%s5", &pmic5_ftsmps525_lv, "vdd-s5"), RPMH_VREG("smps6", "smp%s6", &pmic5_ftsmps525_mv, "vdd-s6"), - RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo, "vdd-l1"), - RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo, "vdd-l2"), - RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3"), + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo515, "vdd-l1"), + RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo515, "vdd-l2"), + RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo515, "vdd-l3"), {} }; @@ -1101,9 +1101,9 @@ static const struct rpmh_vreg_init_data pm8550ve_vreg_data[] = { RPMH_VREG("smps6", "smp%s6", &pmic5_ftsmps525_lv, "vdd-s6"), RPMH_VREG("smps7", "smp%s7", &pmic5_ftsmps525_lv, "vdd-s7"), RPMH_VREG("smps8", "smp%s8", &pmic5_ftsmps525_lv, "vdd-s8"), - RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo, "vdd-l1"), - RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo, "vdd-l2"), - RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo, "vdd-l3"), + RPMH_VREG("ldo1", "ldo%s1", &pmic5_nldo515, "vdd-l1"), + RPMH_VREG("ldo2", "ldo%s2", &pmic5_nldo515, "vdd-l2"), + RPMH_VREG("ldo3", "ldo%s3", &pmic5_nldo515, "vdd-l3"), {} };
The PM8550 uses only NLDOs 515 and the LDO 6 through 8 are low voltage type, so fix accordingly. Fixes: e6e3776d682d ("regulator: qcom-rpmh: Add support for PM8550 regulators") Signed-off-by: Abel Vesa <abel.vesa@linaro.org> --- drivers/regulator/qcom-rpmh-regulator.c | 30 ++++++++++++------------- 1 file changed, 15 insertions(+), 15 deletions(-)