| Message ID | 20230824123001.26778-3-quic_priyjain@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Enable tsens and thermal for sa8775p SoC | expand |
Gentle Reminder. Addressed the comments from previous v1 patch, Please review the v2 patch. On 8/24/2023 6:00 PM, Priyansh Jain wrote: > Add tsens and thermal devicetree node for sa8775p SoC. > > Signed-off-by: Priyansh Jain <quic_priyjain@quicinc.com> > --- > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 1096 +++++++++++++++++++++++++ > 1 file changed, 1096 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > index b130136acffe..abba42ea5946 100644 > --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi > +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > @@ -2306,6 +2306,1102 @@ > > #freq-domain-cells = <1>; > }; > + > + tsens0: thermal-sensor@c222000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c263000 0x0 0x1ff>, > + <0x0 0x0c222000 0x0 0x8>; > + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <12>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens1: thermal-sensor@c223000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c265000 0x0 0x1ff>, > + <0x0 0x0c223000 0x0 0x8>; > + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <12>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens2: thermal-sensor@c224000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c251000 0x0 0x1ff>, > + <0x0 0x0c224000 0x0 0x8>; > + interrupts = <GIC_SPI 572 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 609 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <13>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens3: thermal-sensor@c225000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c252000 0x0 0x1ff>, > + <0x0 0x0c225000 0x0 0x8>; > + interrupts = <GIC_SPI 573 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 610 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <13>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + thermal_zones: thermal-zones { > + aoss-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 0>; > + > + trips { > + aoss0_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + aoss0_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-0-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 1>; > + > + trips { > + cpu000_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu000_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-1-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 2>; > + > + trips { > + cpu010_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu010_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-2-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 3>; > + > + trips { > + cpu020_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu020_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-3-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 4>; > + > + trips { > + cpu030_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu030_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + gpuss-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 5>; > + > + trips { > + gpuss0_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + gpuss0_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + gpuss-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 6>; > + > + trips { > + gpuss1_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + gpuss1_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + gpuss-2-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 7>; > + > + trips { > + gpuss2_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + gpuss2_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + audio-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 8>; > + > + trips { > + audio_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + audio_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + camss-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 9>; > + > + trips { > + camss0_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + camss0_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + pcie-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 10>; > + > + trips { > + pcie0_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + pcie0_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpuss-0-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 11>; > + > + trips { > + cpuss00_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpuss00_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + aoss-1-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 0>; > + > + trips { > + aoss1_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + aoss1_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-0-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 1>; > + > + trips { > + cpu001_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu001_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-1-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 2>; > + > + trips { > + cpu011_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu011_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-2-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 3>; > + > + trips { > + cpu021_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu021_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-0-3-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 4>; > + > + trips { > + cpu031_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu031_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + gpuss-3-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 5>; > + > + trips { > + gpuss3_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + gpuss3_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + gpuss-4-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 6>; > + > + trips { > + gpuss4_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + gpuss4_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + gpuss-5-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 7>; > + > + trips { > + gpuss5_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + gpuss5_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + video-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 8>; > + > + trips { > + video_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + video_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + camss-1-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 9>; > + > + trips { > + camss1_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + camss1_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + pcie-1-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 10>; > + > + trips { > + pcie1_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + pcie1_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpuss-0-1-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens1 11>; > + > + trips { > + cpuss01_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpuss01_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + aoss-2-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 0>; > + > + trips { > + aoss2_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + aoss2_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-0-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 1>; > + > + trips { > + cpu100_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu100_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-1-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 2>; > + > + trips { > + cpu110_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu110_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-2-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 3>; > + > + trips { > + cpu120_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu120_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-3-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 4>; > + > + trips { > + cpu130_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu130_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-0-0-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 5>; > + > + trips { > + nsp000_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp000_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-0-1-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 6>; > + > + trips { > + nsp010_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp010_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-0-2-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 7>; > + > + trips { > + nsp020_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp020_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-1-0-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 8>; > + > + trips { > + nsp100_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp100_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-1-1-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 9>; > + > + trips { > + nsp110_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp110_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-1-2-0-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 10>; > + > + trips { > + nsp120_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp120_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + ddrss-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 11>; > + > + trips { > + ddrss0_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + ddrss0_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpuss-1-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens2 12>; > + > + trips { > + cpuss10_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpuss10_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + aoss-3-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 0>; > + > + trips { > + aoss3_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + aoss3_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-0-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 1>; > + > + trips { > + cpu101_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu101_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-1-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 2>; > + > + trips { > + cpu111_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu111_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-2-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 3>; > + > + trips { > + cpu121_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu121_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpu-1-3-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 4>; > + > + trips { > + cpu131_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpu131_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-0-0-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 5>; > + > + trips { > + nsp001_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp001_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-0-1-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 6>; > + > + trips { > + nsp011_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp011_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-0-2-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 7>; > + > + trips { > + nsp021_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp021_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-1-0-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 8>; > + > + trips { > + nsp101_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp101_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-1-1-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 9>; > + > + trips { > + nsp111_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp111_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + nsp-1-2-1-thermal { > + polling-delay-passive = <10>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 10>; > + > + trips { > + nsp121_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + nsp121_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + ddrss-1-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 11>; > + > + trips { > + ddrss1_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + ddrss1_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + > + cpuss-1-1-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens3 12>; > + > + trips { > + cpuss11_alert0: trip-point0 { > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + cpuss11_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + }; > }; > > arch_timer: timer {
On Thu, Aug 24, 2023 at 06:00:01PM +0530, Priyansh Jain wrote: > Add tsens and thermal devicetree node for sa8775p SoC. > > Signed-off-by: Priyansh Jain <quic_priyjain@quicinc.com> > --- > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 1096 +++++++++++++++++++++++++ > 1 file changed, 1096 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > index b130136acffe..abba42ea5946 100644 > --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi > +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > @@ -2306,6 +2306,1102 @@ > > #freq-domain-cells = <1>; I believe this would be the tail of the cpufreq_hw node, @0x18591000. > }; > + > + tsens0: thermal-sensor@c222000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c263000 0x0 0x1ff>, If so, then this is not inserted to maintain the sort order (by address) of the nodes under /soc. Please update the placement of this node. Also, the unit address above is c222000, but based on this cell it should be c263000. > + <0x0 0x0c222000 0x0 0x8>; > + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <12>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens1: thermal-sensor@c223000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c265000 0x0 0x1ff>, > + <0x0 0x0c223000 0x0 0x8>; > + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <12>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens2: thermal-sensor@c224000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c251000 0x0 0x1ff>, 0x0c251000 < 0x0c265000, please order them properly. > + <0x0 0x0c224000 0x0 0x8>; > + interrupts = <GIC_SPI 572 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 609 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <13>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + tsens3: thermal-sensor@c225000 { > + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; > + reg = <0x0 0x0c252000 0x0 0x1ff>, > + <0x0 0x0c225000 0x0 0x8>; > + interrupts = <GIC_SPI 573 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 610 IRQ_TYPE_LEVEL_HIGH>; > + #qcom,sensors = <13>; > + interrupt-names = "uplow", "critical"; > + #thermal-sensor-cells = <1>; > + }; > + > + thermal_zones: thermal-zones { This does not belong alongside the mmio-devices under /soc, move this out (and keep / sorted alphabetically on the node name). > + aoss-0-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + > + thermal-sensors = <&tsens0 0>; > + > + trips { > + aoss0_alert0: trip-point0 { Why does all these nodes have labels? > + temperature = <105000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + > + aoss0_alert1: trip-point1 { > + temperature = <115000>; > + hysteresis = <5000>; > + type = "passive"; > + }; > + }; > + }; > + [..] > + }; /soc does not end here anymore, please remember to rebase the change on v6.6-rc1. Thanks, Bjorn > }; > > arch_timer: timer { > -- > 2.17.1 >
diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi index b130136acffe..abba42ea5946 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi @@ -2306,6 +2306,1102 @@ #freq-domain-cells = <1>; }; + + tsens0: thermal-sensor@c222000 { + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; + reg = <0x0 0x0c263000 0x0 0x1ff>, + <0x0 0x0c222000 0x0 0x8>; + interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>; + #qcom,sensors = <12>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + tsens1: thermal-sensor@c223000 { + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; + reg = <0x0 0x0c265000 0x0 0x1ff>, + <0x0 0x0c223000 0x0 0x8>; + interrupts = <GIC_SPI 507 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 509 IRQ_TYPE_LEVEL_HIGH>; + #qcom,sensors = <12>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + tsens2: thermal-sensor@c224000 { + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; + reg = <0x0 0x0c251000 0x0 0x1ff>, + <0x0 0x0c224000 0x0 0x8>; + interrupts = <GIC_SPI 572 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 609 IRQ_TYPE_LEVEL_HIGH>; + #qcom,sensors = <13>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + tsens3: thermal-sensor@c225000 { + compatible = "qcom,sa8775p-tsens", "qcom,tsens-v2"; + reg = <0x0 0x0c252000 0x0 0x1ff>, + <0x0 0x0c225000 0x0 0x8>; + interrupts = <GIC_SPI 573 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 610 IRQ_TYPE_LEVEL_HIGH>; + #qcom,sensors = <13>; + interrupt-names = "uplow", "critical"; + #thermal-sensor-cells = <1>; + }; + + thermal_zones: thermal-zones { + aoss-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 0>; + + trips { + aoss0_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + aoss0_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-0-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 1>; + + trips { + cpu000_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu000_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-1-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 2>; + + trips { + cpu010_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu010_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-2-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 3>; + + trips { + cpu020_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu020_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-3-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 4>; + + trips { + cpu030_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu030_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + gpuss-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 5>; + + trips { + gpuss0_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + gpuss0_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + gpuss-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 6>; + + trips { + gpuss1_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + gpuss1_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + gpuss-2-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 7>; + + trips { + gpuss2_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + gpuss2_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + audio-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 8>; + + trips { + audio_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + audio_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + camss-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 9>; + + trips { + camss0_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + camss0_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + pcie-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 10>; + + trips { + pcie0_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + pcie0_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpuss-0-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens0 11>; + + trips { + cpuss00_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpuss00_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + aoss-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 0>; + + trips { + aoss1_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + aoss1_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-0-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 1>; + + trips { + cpu001_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu001_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-1-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 2>; + + trips { + cpu011_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu011_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-2-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 3>; + + trips { + cpu021_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu021_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-0-3-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 4>; + + trips { + cpu031_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu031_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + gpuss-3-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 5>; + + trips { + gpuss3_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + gpuss3_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + gpuss-4-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 6>; + + trips { + gpuss4_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + gpuss4_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + gpuss-5-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 7>; + + trips { + gpuss5_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + gpuss5_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + video-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 8>; + + trips { + video_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + video_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + camss-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 9>; + + trips { + camss1_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + camss1_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + pcie-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 10>; + + trips { + pcie1_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + pcie1_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpuss-0-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens1 11>; + + trips { + cpuss01_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpuss01_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + aoss-2-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 0>; + + trips { + aoss2_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + aoss2_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-0-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 1>; + + trips { + cpu100_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu100_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-1-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 2>; + + trips { + cpu110_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu110_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-2-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 3>; + + trips { + cpu120_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu120_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-3-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 4>; + + trips { + cpu130_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu130_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-0-0-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 5>; + + trips { + nsp000_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp000_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-0-1-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 6>; + + trips { + nsp010_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp010_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-0-2-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 7>; + + trips { + nsp020_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp020_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-1-0-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 8>; + + trips { + nsp100_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp100_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-1-1-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 9>; + + trips { + nsp110_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp110_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-1-2-0-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 10>; + + trips { + nsp120_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp120_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + ddrss-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 11>; + + trips { + ddrss0_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + ddrss0_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpuss-1-0-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens2 12>; + + trips { + cpuss10_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpuss10_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + aoss-3-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 0>; + + trips { + aoss3_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + aoss3_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-0-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 1>; + + trips { + cpu101_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu101_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-1-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 2>; + + trips { + cpu111_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu111_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-2-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 3>; + + trips { + cpu121_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu121_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpu-1-3-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 4>; + + trips { + cpu131_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpu131_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-0-0-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 5>; + + trips { + nsp001_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp001_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-0-1-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 6>; + + trips { + nsp011_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp011_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-0-2-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 7>; + + trips { + nsp021_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp021_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-1-0-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 8>; + + trips { + nsp101_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp101_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-1-1-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 9>; + + trips { + nsp111_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp111_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + nsp-1-2-1-thermal { + polling-delay-passive = <10>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 10>; + + trips { + nsp121_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + nsp121_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + ddrss-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 11>; + + trips { + ddrss1_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + ddrss1_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + + cpuss-1-1-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&tsens3 12>; + + trips { + cpuss11_alert0: trip-point0 { + temperature = <105000>; + hysteresis = <5000>; + type = "passive"; + }; + + cpuss11_alert1: trip-point1 { + temperature = <115000>; + hysteresis = <5000>; + type = "passive"; + }; + }; + }; + }; }; arch_timer: timer {
Add tsens and thermal devicetree node for sa8775p SoC. Signed-off-by: Priyansh Jain <quic_priyjain@quicinc.com> --- arch/arm64/boot/dts/qcom/sa8775p.dtsi | 1096 +++++++++++++++++++++++++ 1 file changed, 1096 insertions(+)