diff mbox series

[1/2] scsi: ufs: ufs-qcom: Update PHY settings only when scaling to higher gears

Message ID 20230908145329.154024-1-manivannan.sadhasivam@linaro.org (mailing list archive)
State Not Applicable
Headers show
Series [1/2] scsi: ufs: ufs-qcom: Update PHY settings only when scaling to higher gears | expand

Commit Message

Manivannan Sadhasivam Sept. 8, 2023, 2:53 p.m. UTC
The "hs_gear" variable is used to program the PHY settings (submode) during
ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
agreed gear changes. Due to this, if the gear got downscaled before suspend
(runtime/system), then while resuming, the PHY settings for the lower gear
will be applied first and later when scaling to max gear with REINIT, the
PHY settings for the max gear will be applied.

This adds a latency while resuming and also really not needed as the PHY
gear settings are backwards compatible i.e., we can continue using the PHY
settings for max gear with lower gear speed.

So let's update the "hs_gear" variable _only_ when the agreed gear is
greater than the current one. This guarantees that the PHY settings will be
changed only during probe time and fatal error condition.

Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
when the PM operation is in progress.

Cc: stable@vger.kernel.org
Fixes: 96a7141da332 ("scsi: ufs: core: Add support for reinitializing the UFS device")
Reported-by: Can Guo <quic_cang@quicinc.com>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/ufs/core/ufshcd.c   | 3 ++-
 drivers/ufs/host/ufs-qcom.c | 9 +++++++--
 2 files changed, 9 insertions(+), 3 deletions(-)

Comments

Konrad Dybcio Sept. 9, 2023, 11:04 a.m. UTC | #1
On 8.09.2023 16:53, Manivannan Sadhasivam wrote:
> The "hs_gear" variable is used to program the PHY settings (submode) during
> ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
> agreed gear changes. Due to this, if the gear got downscaled before suspend
> (runtime/system), then while resuming, the PHY settings for the lower gear
> will be applied first and later when scaling to max gear with REINIT, the
> PHY settings for the max gear will be applied.
> 
> This adds a latency while resuming and also really not needed as the PHY
> gear settings are backwards compatible i.e., we can continue using the PHY
> settings for max gear with lower gear speed.
> 
> So let's update the "hs_gear" variable _only_ when the agreed gear is
> greater than the current one. This guarantees that the PHY settings will be
> changed only during probe time and fatal error condition.
> 
> Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
> when the PM operation is in progress.
> 
> Cc: stable@vger.kernel.org
> Fixes: 96a7141da332 ("scsi: ufs: core: Add support for reinitializing the UFS device")
> Reported-by: Can Guo <quic_cang@quicinc.com>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
Would that not increase power consumption?

I'd presume that the PHY needs to work harder at higher gear
settings to preserve signal integrity with more data flow.

And if so, would that power consumption increase be measurable?
Or is it so small that it doesn't matter?

Konrad
Manivannan Sadhasivam Sept. 9, 2023, 1:58 p.m. UTC | #2
On Sat, Sep 09, 2023 at 01:04:52PM +0200, Konrad Dybcio wrote:
> On 8.09.2023 16:53, Manivannan Sadhasivam wrote:
> > The "hs_gear" variable is used to program the PHY settings (submode) during
> > ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
> > agreed gear changes. Due to this, if the gear got downscaled before suspend
> > (runtime/system), then while resuming, the PHY settings for the lower gear
> > will be applied first and later when scaling to max gear with REINIT, the
> > PHY settings for the max gear will be applied.
> > 
> > This adds a latency while resuming and also really not needed as the PHY
> > gear settings are backwards compatible i.e., we can continue using the PHY
> > settings for max gear with lower gear speed.
> > 
> > So let's update the "hs_gear" variable _only_ when the agreed gear is
> > greater than the current one. This guarantees that the PHY settings will be
> > changed only during probe time and fatal error condition.
> > 
> > Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
> > when the PM operation is in progress.
> > 
> > Cc: stable@vger.kernel.org
> > Fixes: 96a7141da332 ("scsi: ufs: core: Add support for reinitializing the UFS device")
> > Reported-by: Can Guo <quic_cang@quicinc.com>
> > Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> > ---
> Would that not increase power consumption?
> 
> I'd presume that the PHY needs to work harder at higher gear
> settings to preserve signal integrity with more data flow.
> 
> And if so, would that power consumption increase be measurable?
> Or is it so small that it doesn't matter?
> 

Well, the power consumption won't be much. Currently the PHY driver supports
only 2 PHY init sequence, default one (G3/G4) and G4/G5. When ufshcd decides to
run at G4/G5, second sequence would be used and for rest of the gears, first one
would be used. So even today, the G3/G4 sequence is used when ufshcd decides to
downscale to lowest gear G1.

Moreover, on future SoCs the init sequence won't be compatible i.e., we cannot
switch between them. For these reasons, it makes sense to stick to the init
sequence of max gear.

- Mani

> Konrad
Can Guo Sept. 11, 2023, 5:55 a.m. UTC | #3
On 9/8/2023 10:53 PM, Manivannan Sadhasivam wrote:
> The "hs_gear" variable is used to program the PHY settings (submode) during
> ufs_qcom_power_up_sequence(). Currently, it is being updated every time the
> agreed gear changes. Due to this, if the gear got downscaled before suspend
> (runtime/system), then while resuming, the PHY settings for the lower gear
> will be applied first and later when scaling to max gear with REINIT, the
> PHY settings for the max gear will be applied.
>
> This adds a latency while resuming and also really not needed as the PHY
> gear settings are backwards compatible i.e., we can continue using the PHY
> settings for max gear with lower gear speed.
>
> So let's update the "hs_gear" variable _only_ when the agreed gear is
> greater than the current one. This guarantees that the PHY settings will be
> changed only during probe time and fatal error condition.
>
> Due to this, UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH can now be skipped
> when the PM operation is in progress.
>
> Cc: stable@vger.kernel.org
> Fixes: 96a7141da332 ("scsi: ufs: core: Add support for reinitializing the UFS device")
> Reported-by: Can Guo <quic_cang@quicinc.com>
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> ---
>   drivers/ufs/core/ufshcd.c   | 3 ++-
>   drivers/ufs/host/ufs-qcom.c | 9 +++++++--
>   2 files changed, 9 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/ufs/core/ufshcd.c b/drivers/ufs/core/ufshcd.c
> index 34472871610d..1f0a9d96e613 100644
> --- a/drivers/ufs/core/ufshcd.c
> +++ b/drivers/ufs/core/ufshcd.c
> @@ -8782,7 +8782,8 @@ static int ufshcd_probe_hba(struct ufs_hba *hba, bool init_dev_params)
>   	if (ret)
>   		goto out;
>   
> -	if (hba->quirks & UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH) {
> +	if (!hba->pm_op_in_progress &&
> +	    (hba->quirks & UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH)) {
>   		/* Reset the device and controller before doing reinit */
>   		ufshcd_device_reset(hba);
>   		ufshcd_hba_stop(hba);
> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
> index 78689d3479e4..ebb8054a3b3e 100644
> --- a/drivers/ufs/host/ufs-qcom.c
> +++ b/drivers/ufs/host/ufs-qcom.c
> @@ -909,8 +909,13 @@ static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
>   			return ret;
>   		}
>   
> -		/* Use the agreed gear */
> -		host->hs_gear = dev_req_params->gear_tx;
> +		/*
> +		 * Update hs_gear only when the gears are scaled to a higher value. This is because,
> +		 * the PHY gear settings are backwards compatible and we only need to change the PHY
> +		 * settings while scaling to higher gears.
> +		 */
> +		if (dev_req_params->gear_tx > host->hs_gear)
> +			host->hs_gear = dev_req_params->gear_tx;
>   
>   		/* enable the device ref clock before changing to HS mode */
>   		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&

Reviewed-by: Can Guo <quic_cang@quicinc.com>

Tested-by: Can Guo <quic_cang@quicinc.com>
Martin K. Petersen Sept. 14, 2023, 1:21 a.m. UTC | #4
Manivannan,

> The "hs_gear" variable is used to program the PHY settings (submode)
> during ufs_qcom_power_up_sequence(). Currently, it is being updated
> every time the agreed gear changes. Due to this, if the gear got
> downscaled before suspend (runtime/system), then while resuming, the
> PHY settings for the lower gear will be applied first and later when
> scaling to max gear with REINIT, the PHY settings for the max gear
> will be applied.

Applied to 6.7/scsi-staging, thanks!
diff mbox series

Patch

diff --git a/drivers/ufs/core/ufshcd.c b/drivers/ufs/core/ufshcd.c
index 34472871610d..1f0a9d96e613 100644
--- a/drivers/ufs/core/ufshcd.c
+++ b/drivers/ufs/core/ufshcd.c
@@ -8782,7 +8782,8 @@  static int ufshcd_probe_hba(struct ufs_hba *hba, bool init_dev_params)
 	if (ret)
 		goto out;
 
-	if (hba->quirks & UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH) {
+	if (!hba->pm_op_in_progress &&
+	    (hba->quirks & UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH)) {
 		/* Reset the device and controller before doing reinit */
 		ufshcd_device_reset(hba);
 		ufshcd_hba_stop(hba);
diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
index 78689d3479e4..ebb8054a3b3e 100644
--- a/drivers/ufs/host/ufs-qcom.c
+++ b/drivers/ufs/host/ufs-qcom.c
@@ -909,8 +909,13 @@  static int ufs_qcom_pwr_change_notify(struct ufs_hba *hba,
 			return ret;
 		}
 
-		/* Use the agreed gear */
-		host->hs_gear = dev_req_params->gear_tx;
+		/*
+		 * Update hs_gear only when the gears are scaled to a higher value. This is because,
+		 * the PHY gear settings are backwards compatible and we only need to change the PHY
+		 * settings while scaling to higher gears.
+		 */
+		if (dev_req_params->gear_tx > host->hs_gear)
+			host->hs_gear = dev_req_params->gear_tx;
 
 		/* enable the device ref clock before changing to HS mode */
 		if (!ufshcd_is_hs_mode(&hba->pwr_info) &&