| Message ID | 20231025-b4-rb1-usb-host-v1-1-522616c575ef@linaro.org (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | e0cee8dc6757f9f18718eec553be9fffa503e103 |
| Headers | show |
| Series | arm64: dts: qcom: qrb2210-rb1: use USB host mode | expand |
On 10/25/23 13:58, Caleb Connolly wrote: > The default for the QCM2290 platform that this board is based on is OTG > mode, however the role detection logic is not hooked up for this board > and the dwc3 driver is configured to not allow role switching from > userspace. > > Force this board to host mode as this is the preferred usecase until we > get role switching hooked up. Does that not kill usb internet and similar? Konrad
On 26/10/2023 19:56, Konrad Dybcio wrote: > > > On 10/25/23 13:58, Caleb Connolly wrote: >> The default for the QCM2290 platform that this board is based on is OTG >> mode, however the role detection logic is not hooked up for this board >> and the dwc3 driver is configured to not allow role switching from >> userspace. >> >> Force this board to host mode as this is the preferred usecase until we >> get role switching hooked up. > Does that not kill usb internet and similar? like rndis gadget? yes, it does kill that. But in return you get real ethernet ;P This is the preferred default configuration for these boards (I sent a similar patch for rb2 before). The usb_role framework does have support for letting userspace change the role via sysfs, but it's disabled for dwc3. The plan is to enable role switching properly by reading the DIP switch state in the future. > > Konrad
On 10/26/23 21:04, Caleb Connolly wrote: > > > On 26/10/2023 19:56, Konrad Dybcio wrote: >> >> >> On 10/25/23 13:58, Caleb Connolly wrote: >>> The default for the QCM2290 platform that this board is based on is OTG >>> mode, however the role detection logic is not hooked up for this board >>> and the dwc3 driver is configured to not allow role switching from >>> userspace. >>> >>> Force this board to host mode as this is the preferred usecase until we >>> get role switching hooked up. >> Does that not kill usb internet and similar? > > like rndis gadget? yes, it does kill that. But in return you get real > ethernet ;P > > This is the preferred default configuration for these boards (I sent a > similar patch for rb2 before). The usb_role framework does have support > for letting userspace change the role via sysfs, but it's disabled for > dwc3. The plan is to enable role switching properly by reading the DIP > switch state in the future. Ok all that sounds reasonable Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org> Konrad
On Wed, 25 Oct 2023 at 14:58, Caleb Connolly <caleb.connolly@linaro.org> wrote: > > The default for the QCM2290 platform that this board is based on is OTG > mode, however the role detection logic is not hooked up for this board > and the dwc3 driver is configured to not allow role switching from > userspace. > > Force this board to host mode as this is the preferred usecase until we > get role switching hooked up. > > Fixes: e18771961336 ("arm64: dts: qcom: Add initial QTI RB1 device tree") > Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> As a side note, I think we should drop maximum-speed and dr_mode from qcm2290's usb_dwc3 device node. > --- > base-commit: 05d3ef8bba77c1b5f98d941d8b2d4aeab8118ef1 > > // Caleb (they/them) > --- > arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 4 ++++ > 1 file changed, 4 insertions(+)
On Wed, 25 Oct 2023 12:58:00 +0100, Caleb Connolly wrote: > The default for the QCM2290 platform that this board is based on is OTG > mode, however the role detection logic is not hooked up for this board > and the dwc3 driver is configured to not allow role switching from > userspace. > > Force this board to host mode as this is the preferred usecase until we > get role switching hooked up. > > [...] Applied, thanks! [1/1] arm64: dts: qcom: qrb2210-rb1: use USB host mode commit: e0cee8dc6757f9f18718eec553be9fffa503e103 Best regards,
diff --git a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts index eadba066972e..f1961a07c9a3 100644 --- a/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts +++ b/arch/arm64/boot/dts/qcom/qrb2210-rb1.dts @@ -366,6 +366,10 @@ &usb { status = "okay"; }; +&usb_dwc3 { + dr_mode = "host"; +}; + &usb_hsphy { vdd-supply = <&pm2250_l12>; vdda-pll-supply = <&pm2250_l13>;
The default for the QCM2290 platform that this board is based on is OTG mode, however the role detection logic is not hooked up for this board and the dwc3 driver is configured to not allow role switching from userspace. Force this board to host mode as this is the preferred usecase until we get role switching hooked up. Fixes: e18771961336 ("arm64: dts: qcom: Add initial QTI RB1 device tree") Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> --- base-commit: 05d3ef8bba77c1b5f98d941d8b2d4aeab8118ef1 // Caleb (they/them) --- arch/arm64/boot/dts/qcom/qrb2210-rb1.dts | 4 ++++ 1 file changed, 4 insertions(+)