diff mbox series

[v3,1/2] PCI: qcom: reshuffle reset logic in 2_7_0 .init

Message ID 20240210-topic-8280_pcie-v3-1-ee7af6f892a0@linaro.org (mailing list archive)
State Not Applicable
Headers show
Series Qualcomm PCIe RC shutdown & reinit | expand

Commit Message

Konrad Dybcio March 27, 2024, 7:49 p.m. UTC
At least on SC8280XP, if the PCIe reset is asserted, the corresponding
AUX_CLK will be stuck at 'off'. This has not been an issue so far,
since the reset is both left de-asserted by the previous boot stages
and the driver only toggles it briefly in .init.

As part of the upcoming suspend procedure however, the reset will be
held asserted.

Assert the reset (which may end up being a NOP in some cases) and
de-assert it back *before* turning on the clocks in preparation for
introducing RC powerdown and reinitialization.

Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 18 ++++++++----------
 1 file changed, 8 insertions(+), 10 deletions(-)
diff mbox series

Patch

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 14772edcf0d3..d875a9b2b7be 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -925,27 +925,27 @@  static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
 		return ret;
 	}
 
-	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
-	if (ret < 0)
-		goto err_disable_regulators;
-
+	/* Assert the reset to hold the RC in a known state */
 	ret = reset_control_assert(res->rst);
 	if (ret) {
 		dev_err(dev, "reset assert failed (%d)\n", ret);
-		goto err_disable_clocks;
+		goto err_disable_regulators;
 	}
-
 	usleep_range(1000, 1500);
 
+	/* GCC_PCIE_n_AUX_CLK won't come up if the reset is asserted */
 	ret = reset_control_deassert(res->rst);
 	if (ret) {
 		dev_err(dev, "reset deassert failed (%d)\n", ret);
-		goto err_disable_clocks;
+		goto err_disable_regulators;
 	}
-
 	/* Wait for reset to complete, required on SM8450 */
 	usleep_range(1000, 1500);
 
+	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
+	if (ret < 0)
+		goto err_disable_regulators;
+
 	/* configure PCIe to RC mode */
 	writel(DEVICE_TYPE_RC, pcie->parf + PARF_DEVICE_TYPE);
 
@@ -976,8 +976,6 @@  static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
 	writel(val, pcie->parf + PARF_AXI_MSTR_WR_ADDR_HALT_V2);
 
 	return 0;
-err_disable_clocks:
-	clk_bulk_disable_unprepare(res->num_clks, res->clks);
 err_disable_regulators:
 	regulator_bulk_disable(ARRAY_SIZE(res->supplies), res->supplies);