| Message ID | 20240306123006.724934-2-amadeus@jmu.edu.cn (mailing list archive) |
|---|---|
| State | Changes Requested |
| Headers | show |
| Series | arm64: dts: qcom: ipq6018: add sdhci node | expand |
On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@jmu.edu.cn> wrote: > > Add node to support mmc controller inside of IPQ6018. > This controller supports both eMMC and SD cards. > > Tested with: > eMMC (HS200) > SD Card (SDR50/SDR104) > > Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> > --- > arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ > 1 file changed, 19 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > index 322eced0b876..420c192bccd9 100644 > --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { > }; > }; > > + sdhc: mmc@7804000 { > + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; > + reg = <0x0 0x07804000 0x0 0x1000>, > + <0x0 0x07805000 0x0 0x1000>; > + reg-names = "hc", "cqhci"; > + > + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-names = "hc_irq", "pwr_irq"; > + > + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > + <&gcc GCC_SDCC1_APPS_CLK>, > + <&xo>; > + clock-names = "iface", "core", "xo"; > + resets = <&gcc GCC_SDCC1_BCR>; > + max-frequency = <192000000>; If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up to 384 MHz, but here you are limiting it to 192 MHz. Why is it so? > + status = "disabled"; > + }; > + > blsp_dma: dma-controller@7884000 { > compatible = "qcom,bam-v1.7.0"; > reg = <0x0 0x07884000 0x0 0x2b000>; > -- > 2.25.1 > >
On 06. 03. 2024. 20:43, Dmitry Baryshkov wrote: > On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@jmu.edu.cn> wrote: >> Add node to support mmc controller inside of IPQ6018. >> This controller supports both eMMC and SD cards. >> >> Tested with: >> eMMC (HS200) >> SD Card (SDR50/SDR104) >> >> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> >> --- >> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ >> 1 file changed, 19 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi >> index 322eced0b876..420c192bccd9 100644 >> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi >> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi >> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { >> }; >> }; >> >> + sdhc: mmc@7804000 { >> + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; >> + reg = <0x0 0x07804000 0x0 0x1000>, >> + <0x0 0x07805000 0x0 0x1000>; >> + reg-names = "hc", "cqhci"; >> + >> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, >> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; >> + interrupt-names = "hc_irq", "pwr_irq"; >> + >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >> + <&gcc GCC_SDCC1_APPS_CLK>, >> + <&xo>; >> + clock-names = "iface", "core", "xo"; >> + resets = <&gcc GCC_SDCC1_BCR>; >> + max-frequency = <192000000>; > If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up > to 384 MHz, but here you are limiting it to 192 MHz. Why is it so? > > I am not sure that 384MHz is actually supported as IPQ6018 datasheet > clearly indicates that HS400 mode is not supported. > > Regards, > Robert > >> + status = "disabled"; >> + }; >> + >> blsp_dma: dma-controller@7884000 { >> compatible = "qcom,bam-v1.7.0"; >> reg = <0x0 0x07884000 0x0 0x2b000>; >> -- >> 2.25.1 >> >> >
On Wed, 6 Mar 2024 at 22:35, Robert Marko <robimarko@gmail.com> wrote: > > > On 06. 03. 2024. 20:43, Dmitry Baryshkov wrote: > > On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@jmu.edu.cn> wrote: > >> Add node to support mmc controller inside of IPQ6018. > >> This controller supports both eMMC and SD cards. > >> > >> Tested with: > >> eMMC (HS200) > >> SD Card (SDR50/SDR104) > >> > >> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> > >> --- > >> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ > >> 1 file changed, 19 insertions(+) > >> > >> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > >> index 322eced0b876..420c192bccd9 100644 > >> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > >> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > >> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { > >> }; > >> }; > >> > >> + sdhc: mmc@7804000 { > >> + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; > >> + reg = <0x0 0x07804000 0x0 0x1000>, > >> + <0x0 0x07805000 0x0 0x1000>; > >> + reg-names = "hc", "cqhci"; > >> + > >> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, > >> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > >> + interrupt-names = "hc_irq", "pwr_irq"; > >> + > >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > >> + <&gcc GCC_SDCC1_APPS_CLK>, > >> + <&xo>; > >> + clock-names = "iface", "core", "xo"; > >> + resets = <&gcc GCC_SDCC1_BCR>; > >> + max-frequency = <192000000>; > > If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up > > to 384 MHz, but here you are limiting it to 192 MHz. Why is it so? > > > > I am not sure that 384MHz is actually supported as IPQ6018 datasheet > > clearly indicates that HS400 mode is not supported. I didn't check the datasheet, I opened the gcc-ipq6018.c > > > > Regards, > > Robert > > > >> + status = "disabled"; > >> + }; > >> + > >> blsp_dma: dma-controller@7884000 { > >> compatible = "qcom,bam-v1.7.0"; > >> reg = <0x0 0x07884000 0x0 0x2b000>; > >> -- > >> 2.25.1 > >> > >> > >
On Thu, 7 Mar 2024 at 08:28, Dmitry Baryshkov <dmitry.baryshkov@linaro.org> wrote: > > On Wed, 6 Mar 2024 at 22:35, Robert Marko <robimarko@gmail.com> wrote: > > > > > > On 06. 03. 2024. 20:43, Dmitry Baryshkov wrote: > > > On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@jmu.edu.cn> wrote: > > >> Add node to support mmc controller inside of IPQ6018. > > >> This controller supports both eMMC and SD cards. > > >> > > >> Tested with: > > >> eMMC (HS200) > > >> SD Card (SDR50/SDR104) > > >> > > >> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> > > >> --- > > >> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ > > >> 1 file changed, 19 insertions(+) > > >> > > >> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > >> index 322eced0b876..420c192bccd9 100644 > > >> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > >> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > >> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { > > >> }; > > >> }; > > >> > > >> + sdhc: mmc@7804000 { > > >> + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; > > >> + reg = <0x0 0x07804000 0x0 0x1000>, > > >> + <0x0 0x07805000 0x0 0x1000>; > > >> + reg-names = "hc", "cqhci"; > > >> + > > >> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, > > >> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > > >> + interrupt-names = "hc_irq", "pwr_irq"; > > >> + > > >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > > >> + <&gcc GCC_SDCC1_APPS_CLK>, > > >> + <&xo>; > > >> + clock-names = "iface", "core", "xo"; > > >> + resets = <&gcc GCC_SDCC1_BCR>; > > >> + max-frequency = <192000000>; > > > If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up > > > to 384 MHz, but here you are limiting it to 192 MHz. Why is it so? > > > > > > I am not sure that 384MHz is actually supported as IPQ6018 datasheet > > > clearly indicates that HS400 mode is not supported. > > I didn't check the datasheet, I opened the gcc-ipq6018.c I understand that, I just pointed it out, it wouldn't surprise me if the frequency table was just copy/pasted from IPQ8074. Regards, Robert > > > > > > > Regards, > > > Robert > > > > > >> + status = "disabled"; > > >> + }; > > >> + > > >> blsp_dma: dma-controller@7884000 { > > >> compatible = "qcom,bam-v1.7.0"; > > >> reg = <0x0 0x07884000 0x0 0x2b000>; > > >> -- > > >> 2.25.1 > > >> > > >> > > > > > > > -- > With best wishes > Dmitry
On Thu, 7 Mar 2024 at 09:38, Robert Marko <robimarko@gmail.com> wrote: > > On Thu, 7 Mar 2024 at 08:28, Dmitry Baryshkov > <dmitry.baryshkov@linaro.org> wrote: > > > > On Wed, 6 Mar 2024 at 22:35, Robert Marko <robimarko@gmail.com> wrote: > > > > > > > > > On 06. 03. 2024. 20:43, Dmitry Baryshkov wrote: > > > > On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@jmu.edu.cn> wrote: > > > >> Add node to support mmc controller inside of IPQ6018. > > > >> This controller supports both eMMC and SD cards. > > > >> > > > >> Tested with: > > > >> eMMC (HS200) > > > >> SD Card (SDR50/SDR104) > > > >> > > > >> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> > > > >> --- > > > >> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ > > > >> 1 file changed, 19 insertions(+) > > > >> > > > >> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > > >> index 322eced0b876..420c192bccd9 100644 > > > >> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > > >> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi > > > >> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { > > > >> }; > > > >> }; > > > >> > > > >> + sdhc: mmc@7804000 { > > > >> + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; > > > >> + reg = <0x0 0x07804000 0x0 0x1000>, > > > >> + <0x0 0x07805000 0x0 0x1000>; > > > >> + reg-names = "hc", "cqhci"; > > > >> + > > > >> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, > > > >> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; > > > >> + interrupt-names = "hc_irq", "pwr_irq"; > > > >> + > > > >> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, > > > >> + <&gcc GCC_SDCC1_APPS_CLK>, > > > >> + <&xo>; > > > >> + clock-names = "iface", "core", "xo"; > > > >> + resets = <&gcc GCC_SDCC1_BCR>; > > > >> + max-frequency = <192000000>; > > > > If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up > > > > to 384 MHz, but here you are limiting it to 192 MHz. Why is it so? > > > > > > > > I am not sure that 384MHz is actually supported as IPQ6018 datasheet > > > > clearly indicates that HS400 mode is not supported. > > > > I didn't check the datasheet, I opened the gcc-ipq6018.c > > I understand that, I just pointed it out, it wouldn't surprise me if > the frequency table > was just copy/pasted from IPQ8074. Then it might be fixed instead, making the max-frequency property unnecessary. > > Regards, > Robert > > > > > > > > > > Regards, > > > > Robert > > > > > > > >> + status = "disabled"; > > > >> + }; > > > >> + > > > >> blsp_dma: dma-controller@7884000 { > > > >> compatible = "qcom,bam-v1.7.0"; > > > >> reg = <0x0 0x07884000 0x0 0x2b000>; > > > >> -- > > > >> 2.25.1 > > > >> > > > >> > > > > > > > > > > > > -- > > With best wishes > > Dmitry
On 3/7/24 08:50, Dmitry Baryshkov wrote: > On Thu, 7 Mar 2024 at 09:38, Robert Marko <robimarko@gmail.com> wrote: >> >> On Thu, 7 Mar 2024 at 08:28, Dmitry Baryshkov >> <dmitry.baryshkov@linaro.org> wrote: >>> >>> On Wed, 6 Mar 2024 at 22:35, Robert Marko <robimarko@gmail.com> wrote: >>>> >>>> >>>> On 06. 03. 2024. 20:43, Dmitry Baryshkov wrote: >>>>> On Wed, 6 Mar 2024 at 14:31, Chukun Pan <amadeus@jmu.edu.cn> wrote: >>>>>> Add node to support mmc controller inside of IPQ6018. >>>>>> This controller supports both eMMC and SD cards. >>>>>> >>>>>> Tested with: >>>>>> eMMC (HS200) >>>>>> SD Card (SDR50/SDR104) >>>>>> >>>>>> Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> >>>>>> --- >>>>>> arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ >>>>>> 1 file changed, 19 insertions(+) >>>>>> >>>>>> diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi >>>>>> index 322eced0b876..420c192bccd9 100644 >>>>>> --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi >>>>>> +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi >>>>>> @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { >>>>>> }; >>>>>> }; >>>>>> >>>>>> + sdhc: mmc@7804000 { >>>>>> + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; >>>>>> + reg = <0x0 0x07804000 0x0 0x1000>, >>>>>> + <0x0 0x07805000 0x0 0x1000>; >>>>>> + reg-names = "hc", "cqhci"; >>>>>> + >>>>>> + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, >>>>>> + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; >>>>>> + interrupt-names = "hc_irq", "pwr_irq"; >>>>>> + >>>>>> + clocks = <&gcc GCC_SDCC1_AHB_CLK>, >>>>>> + <&gcc GCC_SDCC1_APPS_CLK>, >>>>>> + <&xo>; >>>>>> + clock-names = "iface", "core", "xo"; >>>>>> + resets = <&gcc GCC_SDCC1_BCR>; >>>>>> + max-frequency = <192000000>; >>>>> If I understand correctly, GCC_SDCC1_APPS_CLK support frequencies up >>>>> to 384 MHz, but here you are limiting it to 192 MHz. Why is it so? >>>>> >>>>> I am not sure that 384MHz is actually supported as IPQ6018 datasheet >>>>> clearly indicates that HS400 mode is not supported. >>> >>> I didn't check the datasheet, I opened the gcc-ipq6018.c >> >> I understand that, I just pointed it out, it wouldn't surprise me if >> the frequency table >> was just copy/pasted from IPQ8074. > > Then it might be fixed instead, making the max-frequency property unnecessary. The clock driver contains clock settings that were either autogenerated or manually included, or copypasted. These settings, and particularly downstream, only describe the known-working clock rates and the minimum required voltage setting just to keep them ticking nicely (think running a car with the clutch pressed, no real load), a subset (which may be an improper subset) of which gets translated into the device OPPs (or frequency levels downstream). We should have an OPP table here. Konrad
diff --git a/arch/arm64/boot/dts/qcom/ipq6018.dtsi b/arch/arm64/boot/dts/qcom/ipq6018.dtsi index 322eced0b876..420c192bccd9 100644 --- a/arch/arm64/boot/dts/qcom/ipq6018.dtsi +++ b/arch/arm64/boot/dts/qcom/ipq6018.dtsi @@ -441,6 +441,25 @@ dwc_1: usb@7000000 { }; }; + sdhc: mmc@7804000 { + compatible = "qcom,ipq6018-sdhci", "qcom,sdhci-msm-v5"; + reg = <0x0 0x07804000 0x0 0x1000>, + <0x0 0x07805000 0x0 0x1000>; + reg-names = "hc", "cqhci"; + + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo>; + clock-names = "iface", "core", "xo"; + resets = <&gcc GCC_SDCC1_BCR>; + max-frequency = <192000000>; + status = "disabled"; + }; + blsp_dma: dma-controller@7884000 { compatible = "qcom,bam-v1.7.0"; reg = <0x0 0x07884000 0x0 0x2b000>;
Add node to support mmc controller inside of IPQ6018. This controller supports both eMMC and SD cards. Tested with: eMMC (HS200) SD Card (SDR50/SDR104) Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> --- arch/arm64/boot/dts/qcom/ipq6018.dtsi | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+)