| Message ID | 20240326-rb3gen2-ufs-v1-1-8c5c2dae1e64@quicinc.com (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | arm64: dts: qcom: qcs6490-rb3gen2: Enable UFS | expand |
On 26.03.2024 7:02 PM, Bjorn Andersson wrote: > The rb3gen2 has UFS memory, adjust the necessary supply voltage and add > the controller and phy nodes to enable this. > > Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> > --- > arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 23 +++++++++++++++++++++-- > 1 file changed, 21 insertions(+), 2 deletions(-) > > diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts > index 63ebe0774f1d..0177d93ecd1d 100644 > --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts > +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts > @@ -221,8 +221,8 @@ vreg_l6b_1p2: ldo6 { > > vreg_l7b_2p952: ldo7 { > regulator-name = "vreg_l7b_2p952"; > - regulator-min-microvolt = <2400000>; > - regulator-max-microvolt = <3544000>; > + regulator-min-microvolt = <2952000>; > + regulator-max-microvolt = <2952000>; > regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > }; > > @@ -508,6 +508,25 @@ &usb_1_qmpphy { > status = "okay"; > }; > > +&ufs_mem_hc { > + reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>; > + vcc-supply = <&vreg_l7b_2p952>; > + vcc-max-microamp = <800000>; > + vccq-supply = <&vreg_l9b_1p2>; > + vccq-max-microamp = <900000>; > + vccq2-supply = <&vreg_l9b_1p2>; > + vccq2-max-microamp = <900000>; This probably requires adding supported modes and allow-set-mode to these regs Konrad
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts index 63ebe0774f1d..0177d93ecd1d 100644 --- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts +++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts @@ -221,8 +221,8 @@ vreg_l6b_1p2: ldo6 { vreg_l7b_2p952: ldo7 { regulator-name = "vreg_l7b_2p952"; - regulator-min-microvolt = <2400000>; - regulator-max-microvolt = <3544000>; + regulator-min-microvolt = <2952000>; + regulator-max-microvolt = <2952000>; regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; }; @@ -508,6 +508,25 @@ &usb_1_qmpphy { status = "okay"; }; +&ufs_mem_hc { + reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>; + vcc-supply = <&vreg_l7b_2p952>; + vcc-max-microamp = <800000>; + vccq-supply = <&vreg_l9b_1p2>; + vccq-max-microamp = <900000>; + vccq2-supply = <&vreg_l9b_1p2>; + vccq2-max-microamp = <900000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l10c_0p88>; + vdda-pll-supply = <&vreg_l6b_1p2>; + + status = "okay"; +}; + &wifi { memory-region = <&wlan_fw_mem>; };
The rb3gen2 has UFS memory, adjust the necessary supply voltage and add the controller and phy nodes to enable this. Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com> --- arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 23 +++++++++++++++++++++-- 1 file changed, 21 insertions(+), 2 deletions(-) --- base-commit: 084c8e315db34b59d38d06e684b1a0dd07d30287 change-id: 20240326-rb3gen2-ufs-7ddb07157556 Best regards,