diff mbox series

[v4,2/2] arm64: dts: qcom: sm8550: Add support for Samsung Galaxy Z Fold5

Message ID 20240407-samsung-galaxy-zfold5-q5q-v4-2-8b67b1813653@yahoo.com (mailing list archive)
State Superseded
Headers show
Series Samsung Galaxy Z Fold5 initial support | expand

Commit Message

Alexandru Marc Serdeliuc via B4 Relay April 7, 2024, 5:38 a.m. UTC 
From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>

Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone based on sm8550

Currently working features:
- Framebuffer
- UFS
- i2c
- Buttons

Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
---
 arch/arm64/boot/dts/qcom/Makefile               |   1 +
 arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts | 593 ++++++++++++++++++++++++
 2 files changed, 594 insertions(+)

Comments

Krzysztof Kozlowski April 7, 2024, 9:03 a.m. UTC | #1 
On 07/04/2024 07:38, Alexandru Marc Serdeliuc via B4 Relay wrote:
> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
> 
> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone based on sm8550
> 
> Currently working features:
> - Framebuffer
> - UFS
> - i2c
> - Buttons
> 
> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
> ---
>  arch/arm64/boot/dts/qcom/Makefile               |   1 +

Where is the changelog? This is v4 and nothing (neither here nor in
cover letter) explained what was happening with this patchset.

Tags were ignored, so maybe comments as well?

Please provide *full* and detailed changelog.

Best regards,
Krzysztof
Alexandru Serdeliuc April 7, 2024, 10:03 a.m. UTC | #2 
Hi, please excuse my lack of knowledge, I am still trying to figure out 
how to properly send a patch. Hopefully not wasting your time too much.


Here is what was changed, or I should send a v5 and add the 
modifications to cover letter?

- v4

   . removed a spurious new line

   . removed pcie_1_phy_aux_clk as requested

   . removed secondary pcie1 which does not exists on the device

   . changed firmware extension from .mbn to .mdt

   . added missing reserved memory regions required  by firmware to 
properly load


- v3

   . added b4 version 3

   . removed address and size cells in device description


- v2 added both but added an extra v2 in the subject line instead to b4 
subject header, was requested to send the patch again, along with 
following mods:

   . removed whole bootargs line

   . fixed underscores in reserved memory by removing all reserved 
memory regions

   . added missing idetation to  spash_screen remark

   . validated the dts with "dtbs_check"

   . removed all comments at the end of nodes

   . moved status of the node at the end of the node

   . reversed pin control name with control numbers

   . ordered the  nodes alphabetically


- The initial request was split in two patches sent due to the following 
checkpatch warning, was requested to re send them together:

WARNING: DT binding docs and includes should be a separate patch. See: 
Documentation/devicetree/bindings/submitting-patches.rst


On 7/4/24 11:03, Krzysztof Kozlowski wrote:
> On 07/04/2024 07:38, Alexandru Marc Serdeliuc via B4 Relay wrote:
>> From: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>>
>> Add support for Samsung Galaxy Z Fold5 (q5q) foldable phone based on sm8550
>>
>> Currently working features:
>> - Framebuffer
>> - UFS
>> - i2c
>> - Buttons
>>
>> Signed-off-by: Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
>> ---
>>   arch/arm64/boot/dts/qcom/Makefile               |   1 +
> Where is the changelog? This is v4 and nothing (neither here nor in
> cover letter) explained what was happening with this patchset.
>
> Tags were ignored, so maybe comments as well?
>
> Please provide *full* and detailed changelog.
>
> Best regards,
> Krzysztof
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 7d40ec5e7d21..a7503fd35b6c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -241,6 +241,7 @@  dtb-$(CONFIG_ARCH_QCOM)	+= sm8450-sony-xperia-nagara-pdx224.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-hdk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-qrd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= sm8550-samsung-q5q.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= sm8650-qrd.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-crd.dtb
diff --git a/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
new file mode 100644
index 000000000000..4654ae1364ba
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sm8550-samsung-q5q.dts
@@ -0,0 +1,593 @@ 
+// SPDX-License-cdsp_memIdentifier: BSD-3-Clause
+/*
+ * Copyright (c) 2024, Alexandru Marc Serdeliuc <serdeliuk@yahoo.com>
+ * Copyright (c) 2024, David Wronek <david@mainlining.org>
+ * Copyright (c) 2022, Linaro Limited
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "sm8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/delete-node/ &adspslpi_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &rmtfs_mem;
+
+/ {
+	model = "Samsung Galaxy Z Fold5";
+	compatible = "samsung,q5q", "qcom,sm8550";
+	chassis-type = "handset";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		framebuffer: framebuffer@b8000000 {
+			compatible = "simple-framebuffer";
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			width = <2176>;
+			height = <1812>;
+			stride = <(2176 * 4)>;
+			format = "a8r8g8b8";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&volume_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	vph_pwr: vph-pwr-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	reserved-memory {
+		adspslpi_mem: adspslpi@9ea00000 {
+			reg = <0x0 0x9ea00000 0x0 0x59b4000>;
+			no-map;
+		};
+
+		cdsp_mem: cdsp-region@9c900000 {
+			reg = <0 0x9c900000 0 0x2000000>;
+			no-map;
+		};
+
+		mpss_dsm_mem: mpss-dsm@d4d00000 {
+			reg = <0x0 0xd4d00000 0x0 0x3300000>;
+			no-map;
+		};
+
+		mpss_mem: mpss@8b400000 {
+			reg = <0x0 0x8b400000 0x0 0xfc00000>;
+			no-map;
+		};
+
+		rmtfs_mem: rmtfs-region@d4a80000 {
+			reg = <0x0 0xd4a80000 0x0 0x280000>;
+			no-map;
+		};
+
+		/*
+		 * The bootloader will only keep display hardware enabled
+		 * if this memory region is named exactly 'splash_region'
+		 */
+		splash_region@b8000000 {
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			no-map;
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_1p8: ldo7 {
+			regulator-name = "vreg_l7b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_1p8: ldo8 {
+			regulator-name = "vreg_l8b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b_1p2: ldo11 {
+			regulator-name = "vreg_l11b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p8: ldo12 {
+			regulator-name = "vreg_l12b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p2: ldo14 {
+			regulator-name = "vreg_l14b_3p2";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vreg_l3c_0p91: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vreg_s4e_0p9: smps4 {
+			regulator-name = "vreg_s4e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p1: smps5 {
+			regulator-name = "vreg_s5e_1p1";
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p91: ldo3 {
+			regulator-name = "vreg_l3f_0p91";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vreg_s1g_1p2: smps1 {
+			regulator-name = "vreg_s1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p8: smps2 {
+			regulator-name = "vreg_s2g_0p8";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p7: smps3 {
+			regulator-name = "vreg_s3g_0p7";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p3: smps4 {
+			regulator-name = "vreg_s4g_1p3";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p8: smps5 {
+			regulator-name = "vreg_s5g_0p8";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p8: smps6 {
+			regulator-name = "vreg_s6g_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2g_1p2: ldo2 {
+			regulator-name = "vreg_l2g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8010-rpmh-regulators";
+		qcom,pmic-id = "m";
+
+		vreg_l1m_1p056: ldo1 {
+			regulator-name = "vreg_l1m_1p056";
+			regulator-min-microvolt = <1056000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2m_1p056: ldo2 {
+			regulator-name = "vreg_l2m_1p056";
+			regulator-min-microvolt = <1056000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3m_2p8: ldo3 {
+			regulator-name = "vreg_l3m_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4m_2p8: ldo4 {
+			regulator-name = "vreg_l4m_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5m_1p8: ldo5 {
+			regulator-name = "vreg_l5m_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6m_1p8: ldo6 {
+			regulator-name = "vreg_l6m_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7m_2p9: ldo7 {
+			regulator-name = "vreg_l7m_2p9";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8010-rpmh-regulators";
+		qcom,pmic-id = "n";
+
+		vreg_l1n_1p1: ldo1 {
+			regulator-name = "vreg_l1n_1p1";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2n_1p1: ldo2 {
+			regulator-name = "vreg_l2n_1p1";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3n_2p8: ldo3 {
+			regulator-name = "vreg_l3n_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4n_2p8: ldo4 {
+			regulator-name = "vreg_l4n_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5n_1p8: ldo5 {
+			regulator-name = "vreg_l5n_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6n_3p3: ldo6 {
+			regulator-name = "vreg_l6n_3p3";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7n_2p96: ldo7 {
+			regulator-name = "vreg_l7n_2p96";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&dispcc {
+	status = "disabled";
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+};
+
+&pm8550_gpios {
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	status = "okay";
+	linux,code = <KEY_VOLUMEDOWN>;
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/adsp.mdt",
+			"qcom/sm8550/adsp_dtb.mdt";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8550/cdsp.mdt",
+			"qcom/sm8550/cdsp_dtb.mdt";
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sm8550/modem.mdt",
+			"qcom/sm8550/modem_dtb.mdt";
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32000>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <36 4>, <50 2>;
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	status = "okay";
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};