| Message ID | 20240417-drm-msm-initial-dualpipe-dsc-fixes-v1-1-78ae3ee9a697@somainline.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | drm/msm: Initial fixes for DUALPIPE (+DSC) topology | expand |
On Wed, 17 Apr 2024 at 02:57, Marijn Suijten <marijn.suijten@somainline.org> wrote: > > When dual-DSI (bonded DSI) was added in commit ed9976a09b48 > ("drm/msm/dsi: adjust dsi timing for dual dsi mode") some DBG() prints > were not updated, leading to print the original mode->clock rather > than the adjusted (typically the mode clock divided by two, though more > recently also adjusted for DSC compression) msm_host->pixel_clk_rate > which is passed to clk_set_rate() just below. Fix that by printing the > actual pixel_clk_rate that is being set. > > Fixes: ed9976a09b48 ("drm/msm/dsi: adjust dsi timing for dual dsi mode") > Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> > --- > drivers/gpu/drm/msm/dsi/dsi_host.c | 10 +++++----- > 1 file changed, 5 insertions(+), 5 deletions(-) Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
diff --git a/drivers/gpu/drm/msm/dsi/dsi_host.c b/drivers/gpu/drm/msm/dsi/dsi_host.c index 9d86a6aca6f2..c80be74cf10b 100644 --- a/drivers/gpu/drm/msm/dsi/dsi_host.c +++ b/drivers/gpu/drm/msm/dsi/dsi_host.c @@ -356,8 +356,8 @@ int dsi_link_clk_set_rate_6g(struct msm_dsi_host *msm_host) { int ret; - DBG("Set clk rates: pclk=%d, byteclk=%lu", - msm_host->mode->clock, msm_host->byte_clk_rate); + DBG("Set clk rates: pclk=%lu, byteclk=%lu", + msm_host->pixel_clk_rate, msm_host->byte_clk_rate); ret = dev_pm_opp_set_rate(&msm_host->pdev->dev, msm_host->byte_clk_rate); @@ -430,9 +430,9 @@ int dsi_link_clk_set_rate_v2(struct msm_dsi_host *msm_host) { int ret; - DBG("Set clk rates: pclk=%d, byteclk=%lu, esc_clk=%lu, dsi_src_clk=%lu", - msm_host->mode->clock, msm_host->byte_clk_rate, - msm_host->esc_clk_rate, msm_host->src_clk_rate); + DBG("Set clk rates: pclk=%lu, byteclk=%lu, esc_clk=%lu, dsi_src_clk=%lu", + msm_host->pixel_clk_rate, msm_host->byte_clk_rate, + msm_host->esc_clk_rate, msm_host->src_clk_rate); ret = clk_set_rate(msm_host->byte_clk, msm_host->byte_clk_rate); if (ret) {
When dual-DSI (bonded DSI) was added in commit ed9976a09b48 ("drm/msm/dsi: adjust dsi timing for dual dsi mode") some DBG() prints were not updated, leading to print the original mode->clock rather than the adjusted (typically the mode clock divided by two, though more recently also adjusted for DSC compression) msm_host->pixel_clk_rate which is passed to clk_set_rate() just below. Fix that by printing the actual pixel_clk_rate that is being set. Fixes: ed9976a09b48 ("drm/msm/dsi: adjust dsi timing for dual dsi mode") Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org> --- drivers/gpu/drm/msm/dsi/dsi_host.c | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)