| Message ID | 20240508-otter-bringup-v1-2-c807d3d931f6@linaro.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | qcom: initial support for the SHIFTphone 8 | expand |
…
> Initial support includes:
…
How do you think about to use imperative wordings for improved change descriptions?
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/process/submitting-patches.rst?h=v6.9-rc7#n94
Regards,
Markus
Hi Caleb, On Wed May 8, 2024 at 1:28 AM CEST, Caleb Connolly wrote: > The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following > features: > > * 12GB of RAM, 512GB UFS storage > * 1080p display. > * Hardware kill switches for cameras and microphones > * UART access via type-c SBU pins (enabled by an internal switch) > > Initial support includes: > > * Framebuffer display > * UFS and sdcard storage > * Battery monitoring and USB role switching via pmic glink > * Bluetooth > * Thermals > > Wifi is not yet functional due to a crash in the remoteproc > firmware. > > Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> > --- > arch/arm64/boot/dts/qcom/Makefile | 1 + > arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++ > 2 files changed, 939 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile > index 7d40ec5e7d21..678e800ac797 100644 > --- a/arch/arm64/boot/dts/qcom/Makefile > +++ b/arch/arm64/boot/dts/qcom/Makefile > @@ -92,8 +92,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb > dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcm6490-fairphone-fp5.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb > +dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb > dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb > dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb > diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts > new file mode 100644 > index 000000000000..ceef8b9b2414 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts > @@ -0,0 +1,938 @@ > +// SPDX-License-Identifier: BSD-3-Clause > +/* > + * Based largely on Fairphone 5 DT. :) But not sure this needs to be in the file, in the commit message would be enough imo > + * > + * Copyright (c) 2023, Luca Weiss <luca.weiss@fairphone.com> > + * Copyright (c) 2024, Caleb Connolly <caleb.connolly@linaro.org> > + */ > + > +/dts-v1/; > + > +#define PM7250B_SID 8 > +#define PM7250B_SID1 9 > + > +#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h> > +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> > +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> > +#include "sc7280.dtsi" Sort the list of PMICs by alphabet? Also I guess you can keep the comments I have in fp5.dts which has the 'real' model of the PMIC > +#include "pmk8350.dtsi" /* PMK7325 */ > +#include "pm7325.dtsi" > +#include "pm8350c.dtsi" > +#include "pm7250b.dtsi" > + > +/* There is also a pmr735a */ This thing also exists on FP5 (named SDR-735-*), but I don't think it's accessible to Linux - or that Linux needs to do anything with it. Downstream I also didn't see something for it iirc. > + > +/delete-node/ &rmtfs_mem; > + > +/ { > + model = "SHIFT SHIFTphone 8"; > + compatible = "shift,otter", "qcom,qcm6490"; > + chassis-type = "handset"; > + > + aliases { > + serial0 = &uart5; > + serial1 = &uart7; > + }; > + > + chosen { > + #address-cells = <2>; > + #size-cells = <2>; > + ranges; > + > + stdout-path = "serial0:115200n8"; > + > + framebuffer0: framebuffer@a000000 { > + compatible = "simple-framebuffer"; > + reg = <0x0 0xe1000000 0x0 (2400 * 1080 * 4)>; > + width = <1080>; > + height = <2400>; > + stride = <(1080 * 4)>; > + format = "a8r8g8b8"; > + clocks = <&gcc GCC_DISP_HF_AXI_CLK>; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + pinctrl-0 = <&volume_down_default>; > + pinctrl-names = "default"; > + > + key-volume-up { > + label = "Volume up"; > + gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; > + linux,code = <KEY_VOLUMEUP>; > + debounce-interval = <15>; > + }; > + }; > + > + pmic-glink { > + compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink"; > + > + #address-cells = <1>; > + #size-cells = <0>; > + > + connector@0 { > + compatible = "usb-c-connector"; > + reg = <0>; > + power-role = "dual"; > + data-role = "dual"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + pmic_glink_hs_in: endpoint { > + remote-endpoint = <&usb_1_dwc3_hs>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + pmic_glink_ss_in: endpoint { > + remote-endpoint = <&usb_dp_qmpphy_out>; > + }; > + }; > + > + port@2 { > + reg = <2>; > + > + pmic_glink_sbu: endpoint { > + remote-endpoint = <&fsa4480_sbu_mux>; > + }; > + }; > + }; > + }; > + }; > + > + reserved-memory { > + cont_splash_mem: cont-splash@e1000000 { > + reg = <0x0 0xe1000000 0x0 0x2300000>; > + no-map; > + }; > + > + cdsp_mem: cdsp@88f00000 { > + reg = <0x0 0x88f00000 0x0 0x1e00000>; > + no-map; > + }; > + > + rmtfs_mem: memory@f8500000 { rmtfs@ > + compatible = "qcom,rmtfs-mem"; > + reg = <0x0 0xf8500000 0x0 0x600000>; > + no-map; > + > + qcom,client-id = <1>; > + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>, <QCOM_SCM_VMID_NAV>; > + }; > + }; > + > + thermal-zones { > + camera-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 2>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + chg-skin-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pm7250b_adc_tm 0>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + conn-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pm7250b_adc_tm 1>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + quiet-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 1>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + rear-cam-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 4>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + sdm-skin-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 3>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + > + xo-thermal { > + polling-delay-passive = <0>; > + polling-delay = <0>; > + thermal-sensors = <&pmk8350_adc_tm 0>; > + > + trips { > + active-config0 { > + temperature = <125000>; > + hysteresis = <1000>; > + type = "passive"; > + }; > + }; > + }; > + }; > +}; > + > +&apps_rsc { > + regulators-0 { > + compatible = "qcom,pm7325-rpmh-regulators"; > + qcom,pmic-id = "b"; > + > + vreg_s1b: smps1 { > + regulator-min-microvolt = <1840000>; > + regulator-max-microvolt = <2040000>; > + }; > + > + vreg_s7b: smps7 { > + regulator-min-microvolt = <535000>; > + regulator-max-microvolt = <1120000>; > + }; > + > + vreg_s8b: smps8 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1500000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>; > + }; > + > + vreg_l1b: ldo1 { > + regulator-min-microvolt = <825000>; > + regulator-max-microvolt = <925000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2b: ldo2 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3b: ldo3 { > + regulator-min-microvolt = <312000>; > + regulator-max-microvolt = <910000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6b: ldo6 { > + regulator-min-microvolt = <1140000>; > + regulator-max-microvolt = <1260000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7b: ldo7 { > + /* Constrained for UFS VCC, at least until UFS driver scales voltage */ > + regulator-min-microvolt = <2952000>; > + regulator-max-microvolt = <2952000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8b: ldo8 { > + regulator-min-microvolt = <870000>; > + regulator-max-microvolt = <970000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9b: ldo9 { > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11b: ldo11 { > + regulator-min-microvolt = <1504000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12b: ldo12 { > + regulator-min-microvolt = <751000>; > + regulator-max-microvolt = <824000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13b: ldo13 { > + regulator-min-microvolt = <530000>; > + regulator-max-microvolt = <824000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l14b: ldo14 { > + regulator-min-microvolt = <1080000>; > + regulator-max-microvolt = <1304000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l15b: ldo15 { > + regulator-min-microvolt = <765000>; > + regulator-max-microvolt = <1020000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l16b: ldo16 { > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l17b: ldo17 { > + regulator-min-microvolt = <1700000>; > + regulator-max-microvolt = <1900000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l18b: ldo18 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l19b: ldo19 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + }; > + > + regulators-1 { > + compatible = "qcom,pm8350c-rpmh-regulators"; > + qcom,pmic-id = "c"; > + > + vreg_s1c: smps1 { > + regulator-min-microvolt = <2190000>; > + regulator-max-microvolt = <2210000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_s9c: smps9 { > + regulator-min-microvolt = <1010000>; > + regulator-max-microvolt = <1170000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l1c: ldo1 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1980000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l2c: ldo2 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1950000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l3c: ldo3 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3400000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l4c: ldo4 { > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l5c: ldo5 { > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <3300000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l6c: ldo6 { > + regulator-min-microvolt = <1650000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l7c: ldo7 { > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l8c: ldo8 { > + regulator-min-microvolt = <1620000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l9c: ldo9 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l10c: ldo10 { > + regulator-min-microvolt = <720000>; > + regulator-max-microvolt = <1050000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l11c: ldo11 { > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l12c: ldo12 { > + regulator-min-microvolt = <1650000>; > + regulator-max-microvolt = <2000000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_l13c: ldo13 { > + regulator-min-microvolt = <2700000>; > + regulator-max-microvolt = <3544000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; > + }; > + > + vreg_bob: bob { > + regulator-min-microvolt = <3008000>; > + regulator-max-microvolt = <3960000>; > + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; > + }; > + }; > +}; > + > +&gcc { > + protected-clocks = <GCC_CFG_NOC_LPASS_CLK>, > + <GCC_EDP_CLKREF_EN>, > + <GCC_MSS_CFG_AHB_CLK>, > + <GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>, > + <GCC_MSS_OFFLINE_AXI_CLK>, > + <GCC_MSS_Q6SS_BOOT_CLK_SRC>, > + <GCC_MSS_Q6_MEMNOC_AXI_CLK>, > + <GCC_MSS_SNOC_AXI_CLK>, > + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, > + <GCC_QSPI_CORE_CLK>, > + <GCC_QSPI_CORE_CLK_SRC>, > + <GCC_SEC_CTRL_CLK_SRC>, > + <GCC_WPSS_AHB_BDG_MST_CLK>, > + <GCC_WPSS_AHB_CLK>, > + <GCC_WPSS_RSCP_CLK>; > +}; > + > +&gpi_dma0 { > + status = "okay"; > +}; > + > +&gpi_dma1 { > + status = "okay"; > +}; > + > +&gpu { > + status = "okay"; > +}; > + > +&gpu_zap_shader { > + firmware-name = "qcom/qcm6490/SHIFT/otter/a660_zap.mbn"; > +}; > + > +&i2c1 { > + status = "okay"; > + > + /* PM8008 PMIC @ 8 and 9 */ > + /* rtc6226 FM receiver @ 64 */ > + > + typec-mux@42 { > + compatible = "fcs,fsa4480"; > + reg = <0x42>; > + > + vcc-supply = <&vreg_bob>; > + > + mode-switch; > + orientation-switch; > + > + port { > + fsa4480_sbu_mux: endpoint { > + remote-endpoint = <&pmic_glink_sbu>; > + }; > + }; > + }; > +}; > + > +&i2c4 { > + status = "okay"; > + > + /* tas2563 audio codec @ 4d */ > +}; > + > +&i2c9 { > + status = "okay"; > + > + /* TMS(?) NFC @ 28 */ > + /* Ti drv2624 haptics @ 5a */ > +}; > + > +&i2c13 { > + status = "okay"; > + > + /* focaltech FT3658U @ 38 */ > +}; > + > +&ipa { > + qcom,gsi-loader = "self"; > + memory-region = <&ipa_fw_mem>; > + firmware-name = "qcom/qcm6490/SHIFT/otter/ipa_fws.mbn"; > + status = "okay"; > +}; > + > +&pm7250b_adc { > + channel@4d { > + reg = <ADC5_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "charger_skin_therm"; > + }; > + > + channel@4f { > + reg = <ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "conn_therm"; > + }; > +}; > + > +&pm7250b_adc_tm { > + status = "okay"; > + > + charger-skin-therm@0 { > + reg = <0>; > + io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + conn-therm@1 { > + reg = <1>; > + io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > +}; > + > +&pm7325_gpios { > + volume_down_default: volume-down-default-state { > + pins = "gpio6"; > + function = PMIC_GPIO_FUNC_NORMAL; > + power-source = <1>; > + bias-pull-up; > + input-enable; > + }; > +}; > + > +&pmk8350_adc_tm { > + status = "okay"; > + > + xo-therm@0 { > + reg = <0>; > + io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + quiet-therm@1 { > + reg = <1>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + cam-flash-therm@2 { > + reg = <2>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + sdm-skin-therm@3 { > + reg = <3>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > + > + wide-rfc-therm@4 { > + reg = <4>; > + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time-us = <200>; > + }; > +}; > + > +&pmk8350_rtc { > + status = "okay"; > +}; > + > +&pmk8350_vadc { > + status = "okay"; > + > + channel@44 { > + reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pmk8350_xo_therm"; > + }; > + > + channel@144 { > + reg = <PM7325_ADC7_AMUX_THM1_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_quiet_therm"; > + }; > + > + channel@145 { > + reg = <PM7325_ADC7_AMUX_THM2_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_cam_flash_therm"; > + }; > + > + channel@146 { > + reg = <PM7325_ADC7_AMUX_THM3_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_sdm_skin_therm"; > + }; > + > + channel@147 { > + reg = <PM7325_ADC7_AMUX_THM4_100K_PU>; > + qcom,ratiometric; > + qcom,hw-settle-time = <200>; > + qcom,pre-scaling = <1 1>; > + label = "pm7325_wide_rfc_therm"; > + }; > +}; > + > +&pon_pwrkey { > + status = "okay"; > +}; > + > +&pon_resin { > + linux,code = <KEY_VOLUMEDOWN>; > + status = "okay"; > +}; > + > +&qup_spi13_cs { > + drive-strength = <6>; > + bias-disable; > +}; > + > +&qup_spi13_data_clk { > + drive-strength = <6>; > + bias-disable; > +}; > + > +&qup_uart5_rx { > + drive-strength = <2>; > + bias-disable; > +}; > + > +&qup_uart5_tx { > + drive-strength = <2>; > + bias-disable; > +}; > + > +&qupv3_id_0 { > + status = "okay"; > +}; > + > +&qupv3_id_1 { > + status = "okay"; > +}; > + > +&remoteproc_adsp { > + firmware-name = "qcom/qcm6490/SHIFT/otter/adsp.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_cdsp { > + firmware-name = "qcom/qcm6490/SHIFT/otter/cdsp.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_mpss { > + firmware-name = "qcom/qcm6490/SHIFT/otter/modem.mbn"; > + status = "okay"; > +}; > + > +&remoteproc_wpss { > + firmware-name = "qcom/qcm6490/SHIFT/otter/wpss.mbn"; > + /* > + * FIXME: wpss remoteproc crashes during boot with: > + * qcom_q6v5_pas 8a00000.remoteproc: fatal error received: > + * cmnos_thread.c:4645:Asserted in > + * cmnos_allocram.c:cmnos_allocram_base_with_alignment_recurse:497 > + * with Args:0x3,0x3,0x0 > + */ > + status = "disabled"; > +}; > + > +&sdc2_clk { > + drive-strength = <16>; > + bias-disable; > +}; > + > +&sdc2_cmd { > + drive-strength = <10>; > + bias-pull-up; > +}; > + > +&sdc2_data { > + drive-strength = <10>; > + bias-pull-up; > +}; > + > +&sdhc_2 { > + vmmc-supply = <&vreg_l9c>; > + vqmmc-supply = <&vreg_l6c>; > + > + pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>; > + pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>; > + > + status = "okay"; > +}; > + > +&tlmm { > + /* > + * 48-52: protected by XPU, not sure why. > + */ > + gpio-reserved-ranges = <48 4>; If they really shouldn't be protected from firmware level (fingerprint reader or whatnot), somebody at SHIFT should patch TZ firmware and change the owner from TZ to HLOS. > + > + bluetooth_enable_default: bluetooth-enable-default-state { > + pins = "gpio85"; > + function = "gpio"; > + output-low; > + bias-disable; > + }; > + > + qup_uart7_sleep_cts: qup-uart7-sleep-cts-state { > + pins = "gpio28"; > + function = "gpio"; > + /* > + * Configure a bias-bus-hold on CTS to lower power > + * usage when Bluetooth is turned off. Bus hold will > + * maintain a low power state regardless of whether > + * the Bluetooth module drives the pin in either > + * direction or leaves the pin fully unpowered. > + */ > + bias-bus-hold; > + }; > + > + qup_uart7_sleep_rts: qup-uart7-sleep-rts-state { > + pins = "gpio29"; > + function = "gpio"; > + /* > + * Configure pull-down on RTS. As RTS is active low > + * signal, pull it low to indicate the BT SoC that it > + * can wakeup the system anytime from suspend state by > + * pulling RX low (by sending wakeup bytes). > + */ > + bias-pull-down; > + }; > + > + qup_uart7_sleep_tx: qup-uart7-sleep-tx-state { > + pins = "gpio30"; > + function = "gpio"; > + /* > + * Configure pull-up on TX when it isn't actively driven > + * to prevent BT SoC from receiving garbage during sleep. > + */ > + bias-pull-up; > + }; > + > + qup_uart7_sleep_rx: qup-uart7-sleep-rx-state { > + pins = "gpio31"; > + function = "gpio"; > + /* > + * Configure a pull-up on RX. This is needed to avoid > + * garbage data when the TX pin of the Bluetooth module > + * is floating which may cause spurious wakeups. > + */ > + bias-pull-up; > + }; > + > + sw_ctrl_default: sw-ctrl-default-state { > + pins = "gpio86"; > + function = "gpio"; > + bias-pull-down; > + }; > +}; > + > +&uart5 { > + compatible = "qcom,geni-debug-uart"; This should be redundant soon if the author resends anytime soon https://lore.kernel.org/linux-arm-msm/20240416105650.2626-1-quic_vdadhani@quicinc.com/ Don't see anything wrong with the rest Regards Luca > + status = "okay"; > +}; > + > +&uart7 { > + /delete-property/interrupts; > + interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, > + <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; > + > + pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; > + pinctrl-names = "default", "sleep"; > + > + status = "okay"; > + > + bluetooth: bluetooth { > + compatible = "qcom,wcn6750-bt"; > + > + pinctrl-0 = <&bluetooth_enable_default>, <&sw_ctrl_default>; > + pinctrl-names = "default"; > + > + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; > + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; > + > + vddio-supply = <&vreg_l19b>; > + vddaon-supply = <&vreg_s7b>; > + vddbtcxmx-supply = <&vreg_s7b>; > + vddrfacmn-supply = <&vreg_s7b>; > + vddrfa0p8-supply = <&vreg_s7b>; > + vddrfa1p7-supply = <&vreg_s1b>; > + vddrfa1p2-supply = <&vreg_s8b>; > + vddrfa2p2-supply = <&vreg_s1c>; > + vddasd-supply = <&vreg_l11c>; > + > + max-speed = <3200000>; > + }; > +}; > + > +&ufs_mem_hc { > + reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>; > + > + vcc-supply = <&vreg_l7b>; > + vcc-max-microamp = <800000>; > + /* > + * Technically l9b enables an eLDO (supplied by s1b) which then powers > + * VCCQ2 of the UFS. > + */ > + vccq-supply = <&vreg_l9b>; > + vccq-max-microamp = <900000>; > + > + status = "okay"; > +}; > + > +&ufs_mem_phy { > + vdda-phy-supply = <&vreg_l10c>; > + vdda-pll-supply = <&vreg_l6b>; > + > + status = "okay"; > +}; > + > +&usb_1 { > + status = "okay"; > +}; > + > +&usb_1_dwc3 { > + dr_mode = "otg"; > + usb-role-switch; > +}; > + > +&usb_1_dwc3_hs { > + remote-endpoint = <&pmic_glink_hs_in>; > +}; > + > +&usb_dp_qmpphy_out { > + remote-endpoint = <&pmic_glink_ss_in>; > +}; > + > +&usb_1_hsphy { > + vdda-pll-supply = <&vreg_l10c>; > + vdda18-supply = <&vreg_l1c>; > + vdda33-supply = <&vreg_l2b>; > + > + qcom,hs-crossover-voltage-microvolt = <28000>; > + qcom,hs-output-impedance-micro-ohms = <2600000>; > + qcom,hs-rise-fall-time-bp = <5430>; > + qcom,hs-disconnect-bp = <1743>; > + qcom,hs-amplitude-bp = <2430>; > + > + qcom,pre-emphasis-amplitude-bp = <20000>; > + qcom,pre-emphasis-duration-bp = <20000>; > + > + qcom,squelch-detector-bp = <(-2090)>; > + > + orientation-switch; > + > + status = "okay"; > +}; > + > +&usb_1_qmpphy { > + vdda-phy-supply = <&vreg_l6b>; > + vdda-pll-supply = <&vreg_l1b>; > + > + status = "okay"; > +}; > + > +&wifi { > + qcom,ath11k-calibration-variant = "SHIFTphone_8"; > + > + /* FIXME: wpss remoteproc crashes during init */ > + status = "disabled"; > +};
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile index 7d40ec5e7d21..678e800ac797 100644 --- a/arch/arm64/boot/dts/qcom/Makefile +++ b/arch/arm64/boot/dts/qcom/Makefile @@ -92,8 +92,9 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb dtb-$(CONFIG_ARCH_QCOM) += qcm6490-fairphone-fp5.dtb dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb +dtb-$(CONFIG_ARCH_QCOM) += qcm6490-shift-otter.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb dtb-$(CONFIG_ARCH_QCOM) += qcs6490-rb3gen2.dtb dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb diff --git a/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts new file mode 100644 index 000000000000..ceef8b9b2414 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts @@ -0,0 +1,938 @@ +// SPDX-License-Identifier: BSD-3-Clause +/* + * Based largely on Fairphone 5 DT. + * + * Copyright (c) 2023, Luca Weiss <luca.weiss@fairphone.com> + * Copyright (c) 2024, Caleb Connolly <caleb.connolly@linaro.org> + */ + +/dts-v1/; + +#define PM7250B_SID 8 +#define PM7250B_SID1 9 + +#include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h> +#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h> +#include "sc7280.dtsi" +#include "pmk8350.dtsi" /* PMK7325 */ +#include "pm7325.dtsi" +#include "pm8350c.dtsi" +#include "pm7250b.dtsi" + +/* There is also a pmr735a */ + +/delete-node/ &rmtfs_mem; + +/ { + model = "SHIFT SHIFTphone 8"; + compatible = "shift,otter", "qcom,qcm6490"; + chassis-type = "handset"; + + aliases { + serial0 = &uart5; + serial1 = &uart7; + }; + + chosen { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + stdout-path = "serial0:115200n8"; + + framebuffer0: framebuffer@a000000 { + compatible = "simple-framebuffer"; + reg = <0x0 0xe1000000 0x0 (2400 * 1080 * 4)>; + width = <1080>; + height = <2400>; + stride = <(1080 * 4)>; + format = "a8r8g8b8"; + clocks = <&gcc GCC_DISP_HF_AXI_CLK>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + pinctrl-0 = <&volume_down_default>; + pinctrl-names = "default"; + + key-volume-up { + label = "Volume up"; + gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + debounce-interval = <15>; + }; + }; + + pmic-glink { + compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink"; + + #address-cells = <1>; + #size-cells = <0>; + + connector@0 { + compatible = "usb-c-connector"; + reg = <0>; + power-role = "dual"; + data-role = "dual"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + pmic_glink_hs_in: endpoint { + remote-endpoint = <&usb_1_dwc3_hs>; + }; + }; + + port@1 { + reg = <1>; + + pmic_glink_ss_in: endpoint { + remote-endpoint = <&usb_dp_qmpphy_out>; + }; + }; + + port@2 { + reg = <2>; + + pmic_glink_sbu: endpoint { + remote-endpoint = <&fsa4480_sbu_mux>; + }; + }; + }; + }; + }; + + reserved-memory { + cont_splash_mem: cont-splash@e1000000 { + reg = <0x0 0xe1000000 0x0 0x2300000>; + no-map; + }; + + cdsp_mem: cdsp@88f00000 { + reg = <0x0 0x88f00000 0x0 0x1e00000>; + no-map; + }; + + rmtfs_mem: memory@f8500000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0xf8500000 0x0 0x600000>; + no-map; + + qcom,client-id = <1>; + qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>, <QCOM_SCM_VMID_NAV>; + }; + }; + + thermal-zones { + camera-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pmk8350_adc_tm 2>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + chg-skin-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm7250b_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + conn-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pm7250b_adc_tm 1>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + quiet-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pmk8350_adc_tm 1>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + rear-cam-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pmk8350_adc_tm 4>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + sdm-skin-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pmk8350_adc_tm 3>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + + xo-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + thermal-sensors = <&pmk8350_adc_tm 0>; + + trips { + active-config0 { + temperature = <125000>; + hysteresis = <1000>; + type = "passive"; + }; + }; + }; + }; +}; + +&apps_rsc { + regulators-0 { + compatible = "qcom,pm7325-rpmh-regulators"; + qcom,pmic-id = "b"; + + vreg_s1b: smps1 { + regulator-min-microvolt = <1840000>; + regulator-max-microvolt = <2040000>; + }; + + vreg_s7b: smps7 { + regulator-min-microvolt = <535000>; + regulator-max-microvolt = <1120000>; + }; + + vreg_s8b: smps8 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1500000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>; + }; + + vreg_l1b: ldo1 { + regulator-min-microvolt = <825000>; + regulator-max-microvolt = <925000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2b: ldo2 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3b: ldo3 { + regulator-min-microvolt = <312000>; + regulator-max-microvolt = <910000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6b: ldo6 { + regulator-min-microvolt = <1140000>; + regulator-max-microvolt = <1260000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7b: ldo7 { + /* Constrained for UFS VCC, at least until UFS driver scales voltage */ + regulator-min-microvolt = <2952000>; + regulator-max-microvolt = <2952000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8b: ldo8 { + regulator-min-microvolt = <870000>; + regulator-max-microvolt = <970000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9b: ldo9 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11b: ldo11 { + regulator-min-microvolt = <1504000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12b: ldo12 { + regulator-min-microvolt = <751000>; + regulator-max-microvolt = <824000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13b: ldo13 { + regulator-min-microvolt = <530000>; + regulator-max-microvolt = <824000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l14b: ldo14 { + regulator-min-microvolt = <1080000>; + regulator-max-microvolt = <1304000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l15b: ldo15 { + regulator-min-microvolt = <765000>; + regulator-max-microvolt = <1020000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l16b: ldo16 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l17b: ldo17 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l18b: ldo18 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l19b: ldo19 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + }; + + regulators-1 { + compatible = "qcom,pm8350c-rpmh-regulators"; + qcom,pmic-id = "c"; + + vreg_s1c: smps1 { + regulator-min-microvolt = <2190000>; + regulator-max-microvolt = <2210000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_s9c: smps9 { + regulator-min-microvolt = <1010000>; + regulator-max-microvolt = <1170000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l1c: ldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1980000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l2c: ldo2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1950000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l3c: ldo3 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3400000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l4c: ldo4 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l5c: ldo5 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <3300000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l6c: ldo6 { + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l7c: ldo7 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l8c: ldo8 { + regulator-min-microvolt = <1620000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l9c: ldo9 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l10c: ldo10 { + regulator-min-microvolt = <720000>; + regulator-max-microvolt = <1050000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l11c: ldo11 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l12c: ldo12 { + regulator-min-microvolt = <1650000>; + regulator-max-microvolt = <2000000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_l13c: ldo13 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3544000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; + }; + + vreg_bob: bob { + regulator-min-microvolt = <3008000>; + regulator-max-microvolt = <3960000>; + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; + }; + }; +}; + +&gcc { + protected-clocks = <GCC_CFG_NOC_LPASS_CLK>, + <GCC_EDP_CLKREF_EN>, + <GCC_MSS_CFG_AHB_CLK>, + <GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>, + <GCC_MSS_OFFLINE_AXI_CLK>, + <GCC_MSS_Q6SS_BOOT_CLK_SRC>, + <GCC_MSS_Q6_MEMNOC_AXI_CLK>, + <GCC_MSS_SNOC_AXI_CLK>, + <GCC_QSPI_CNOC_PERIPH_AHB_CLK>, + <GCC_QSPI_CORE_CLK>, + <GCC_QSPI_CORE_CLK_SRC>, + <GCC_SEC_CTRL_CLK_SRC>, + <GCC_WPSS_AHB_BDG_MST_CLK>, + <GCC_WPSS_AHB_CLK>, + <GCC_WPSS_RSCP_CLK>; +}; + +&gpi_dma0 { + status = "okay"; +}; + +&gpi_dma1 { + status = "okay"; +}; + +&gpu { + status = "okay"; +}; + +&gpu_zap_shader { + firmware-name = "qcom/qcm6490/SHIFT/otter/a660_zap.mbn"; +}; + +&i2c1 { + status = "okay"; + + /* PM8008 PMIC @ 8 and 9 */ + /* rtc6226 FM receiver @ 64 */ + + typec-mux@42 { + compatible = "fcs,fsa4480"; + reg = <0x42>; + + vcc-supply = <&vreg_bob>; + + mode-switch; + orientation-switch; + + port { + fsa4480_sbu_mux: endpoint { + remote-endpoint = <&pmic_glink_sbu>; + }; + }; + }; +}; + +&i2c4 { + status = "okay"; + + /* tas2563 audio codec @ 4d */ +}; + +&i2c9 { + status = "okay"; + + /* TMS(?) NFC @ 28 */ + /* Ti drv2624 haptics @ 5a */ +}; + +&i2c13 { + status = "okay"; + + /* focaltech FT3658U @ 38 */ +}; + +&ipa { + qcom,gsi-loader = "self"; + memory-region = <&ipa_fw_mem>; + firmware-name = "qcom/qcm6490/SHIFT/otter/ipa_fws.mbn"; + status = "okay"; +}; + +&pm7250b_adc { + channel@4d { + reg = <ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "charger_skin_therm"; + }; + + channel@4f { + reg = <ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "conn_therm"; + }; +}; + +&pm7250b_adc_tm { + status = "okay"; + + charger-skin-therm@0 { + reg = <0>; + io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + conn-therm@1 { + reg = <1>; + io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pm7325_gpios { + volume_down_default: volume-down-default-state { + pins = "gpio6"; + function = PMIC_GPIO_FUNC_NORMAL; + power-source = <1>; + bias-pull-up; + input-enable; + }; +}; + +&pmk8350_adc_tm { + status = "okay"; + + xo-therm@0 { + reg = <0>; + io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + quiet-therm@1 { + reg = <1>; + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + cam-flash-therm@2 { + reg = <2>; + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + sdm-skin-therm@3 { + reg = <3>; + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; + + wide-rfc-therm@4 { + reg = <4>; + io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time-us = <200>; + }; +}; + +&pmk8350_rtc { + status = "okay"; +}; + +&pmk8350_vadc { + status = "okay"; + + channel@44 { + reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pmk8350_xo_therm"; + }; + + channel@144 { + reg = <PM7325_ADC7_AMUX_THM1_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pm7325_quiet_therm"; + }; + + channel@145 { + reg = <PM7325_ADC7_AMUX_THM2_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pm7325_cam_flash_therm"; + }; + + channel@146 { + reg = <PM7325_ADC7_AMUX_THM3_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pm7325_sdm_skin_therm"; + }; + + channel@147 { + reg = <PM7325_ADC7_AMUX_THM4_100K_PU>; + qcom,ratiometric; + qcom,hw-settle-time = <200>; + qcom,pre-scaling = <1 1>; + label = "pm7325_wide_rfc_therm"; + }; +}; + +&pon_pwrkey { + status = "okay"; +}; + +&pon_resin { + linux,code = <KEY_VOLUMEDOWN>; + status = "okay"; +}; + +&qup_spi13_cs { + drive-strength = <6>; + bias-disable; +}; + +&qup_spi13_data_clk { + drive-strength = <6>; + bias-disable; +}; + +&qup_uart5_rx { + drive-strength = <2>; + bias-disable; +}; + +&qup_uart5_tx { + drive-strength = <2>; + bias-disable; +}; + +&qupv3_id_0 { + status = "okay"; +}; + +&qupv3_id_1 { + status = "okay"; +}; + +&remoteproc_adsp { + firmware-name = "qcom/qcm6490/SHIFT/otter/adsp.mbn"; + status = "okay"; +}; + +&remoteproc_cdsp { + firmware-name = "qcom/qcm6490/SHIFT/otter/cdsp.mbn"; + status = "okay"; +}; + +&remoteproc_mpss { + firmware-name = "qcom/qcm6490/SHIFT/otter/modem.mbn"; + status = "okay"; +}; + +&remoteproc_wpss { + firmware-name = "qcom/qcm6490/SHIFT/otter/wpss.mbn"; + /* + * FIXME: wpss remoteproc crashes during boot with: + * qcom_q6v5_pas 8a00000.remoteproc: fatal error received: + * cmnos_thread.c:4645:Asserted in + * cmnos_allocram.c:cmnos_allocram_base_with_alignment_recurse:497 + * with Args:0x3,0x3,0x0 + */ + status = "disabled"; +}; + +&sdc2_clk { + drive-strength = <16>; + bias-disable; +}; + +&sdc2_cmd { + drive-strength = <10>; + bias-pull-up; +}; + +&sdc2_data { + drive-strength = <10>; + bias-pull-up; +}; + +&sdhc_2 { + vmmc-supply = <&vreg_l9c>; + vqmmc-supply = <&vreg_l6c>; + + pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>; + pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>; + + status = "okay"; +}; + +&tlmm { + /* + * 48-52: protected by XPU, not sure why. + */ + gpio-reserved-ranges = <48 4>; + + bluetooth_enable_default: bluetooth-enable-default-state { + pins = "gpio85"; + function = "gpio"; + output-low; + bias-disable; + }; + + qup_uart7_sleep_cts: qup-uart7-sleep-cts-state { + pins = "gpio28"; + function = "gpio"; + /* + * Configure a bias-bus-hold on CTS to lower power + * usage when Bluetooth is turned off. Bus hold will + * maintain a low power state regardless of whether + * the Bluetooth module drives the pin in either + * direction or leaves the pin fully unpowered. + */ + bias-bus-hold; + }; + + qup_uart7_sleep_rts: qup-uart7-sleep-rts-state { + pins = "gpio29"; + function = "gpio"; + /* + * Configure pull-down on RTS. As RTS is active low + * signal, pull it low to indicate the BT SoC that it + * can wakeup the system anytime from suspend state by + * pulling RX low (by sending wakeup bytes). + */ + bias-pull-down; + }; + + qup_uart7_sleep_tx: qup-uart7-sleep-tx-state { + pins = "gpio30"; + function = "gpio"; + /* + * Configure pull-up on TX when it isn't actively driven + * to prevent BT SoC from receiving garbage during sleep. + */ + bias-pull-up; + }; + + qup_uart7_sleep_rx: qup-uart7-sleep-rx-state { + pins = "gpio31"; + function = "gpio"; + /* + * Configure a pull-up on RX. This is needed to avoid + * garbage data when the TX pin of the Bluetooth module + * is floating which may cause spurious wakeups. + */ + bias-pull-up; + }; + + sw_ctrl_default: sw-ctrl-default-state { + pins = "gpio86"; + function = "gpio"; + bias-pull-down; + }; +}; + +&uart5 { + compatible = "qcom,geni-debug-uart"; + status = "okay"; +}; + +&uart7 { + /delete-property/interrupts; + interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, + <&tlmm 31 IRQ_TYPE_EDGE_FALLING>; + + pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; + pinctrl-names = "default", "sleep"; + + status = "okay"; + + bluetooth: bluetooth { + compatible = "qcom,wcn6750-bt"; + + pinctrl-0 = <&bluetooth_enable_default>, <&sw_ctrl_default>; + pinctrl-names = "default"; + + enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; + swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; + + vddio-supply = <&vreg_l19b>; + vddaon-supply = <&vreg_s7b>; + vddbtcxmx-supply = <&vreg_s7b>; + vddrfacmn-supply = <&vreg_s7b>; + vddrfa0p8-supply = <&vreg_s7b>; + vddrfa1p7-supply = <&vreg_s1b>; + vddrfa1p2-supply = <&vreg_s8b>; + vddrfa2p2-supply = <&vreg_s1c>; + vddasd-supply = <&vreg_l11c>; + + max-speed = <3200000>; + }; +}; + +&ufs_mem_hc { + reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>; + + vcc-supply = <&vreg_l7b>; + vcc-max-microamp = <800000>; + /* + * Technically l9b enables an eLDO (supplied by s1b) which then powers + * VCCQ2 of the UFS. + */ + vccq-supply = <&vreg_l9b>; + vccq-max-microamp = <900000>; + + status = "okay"; +}; + +&ufs_mem_phy { + vdda-phy-supply = <&vreg_l10c>; + vdda-pll-supply = <&vreg_l6b>; + + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&usb_1_dwc3 { + dr_mode = "otg"; + usb-role-switch; +}; + +&usb_1_dwc3_hs { + remote-endpoint = <&pmic_glink_hs_in>; +}; + +&usb_dp_qmpphy_out { + remote-endpoint = <&pmic_glink_ss_in>; +}; + +&usb_1_hsphy { + vdda-pll-supply = <&vreg_l10c>; + vdda18-supply = <&vreg_l1c>; + vdda33-supply = <&vreg_l2b>; + + qcom,hs-crossover-voltage-microvolt = <28000>; + qcom,hs-output-impedance-micro-ohms = <2600000>; + qcom,hs-rise-fall-time-bp = <5430>; + qcom,hs-disconnect-bp = <1743>; + qcom,hs-amplitude-bp = <2430>; + + qcom,pre-emphasis-amplitude-bp = <20000>; + qcom,pre-emphasis-duration-bp = <20000>; + + qcom,squelch-detector-bp = <(-2090)>; + + orientation-switch; + + status = "okay"; +}; + +&usb_1_qmpphy { + vdda-phy-supply = <&vreg_l6b>; + vdda-pll-supply = <&vreg_l1b>; + + status = "okay"; +}; + +&wifi { + qcom,ath11k-calibration-variant = "SHIFTphone_8"; + + /* FIXME: wpss remoteproc crashes during init */ + status = "disabled"; +};
The SHIFTphone 8 is an upcoming QCM6490 smartphone, it has the following features: * 12GB of RAM, 512GB UFS storage * 1080p display. * Hardware kill switches for cameras and microphones * UART access via type-c SBU pins (enabled by an internal switch) Initial support includes: * Framebuffer display * UFS and sdcard storage * Battery monitoring and USB role switching via pmic glink * Bluetooth * Thermals Wifi is not yet functional due to a crash in the remoteproc firmware. Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org> --- arch/arm64/boot/dts/qcom/Makefile | 1 + arch/arm64/boot/dts/qcom/qcm6490-shift-otter.dts | 938 +++++++++++++++++++++++ 2 files changed, 939 insertions(+)