[v4,6/8] serial: qcom-geni: Just set the watermark level once

Commit Message

Doug Anderson June 10, 2024, 10:24 p.m. UTC

There's no reason to set the TX watermark level to 0 when we disable
TX since we're disabling the interrupt anyway. Just set the watermark
level once at init time and leave it alone.

Signed-off-by: Douglas Anderson <[e-mail]>
---

(no changes since v2)

Changes in v2:
- New

 drivers/tty/serial/qcom_geni_serial.c | 5 +----
 1 file changed, 1 insertion(+), 4 deletions(-)

Patch

diff --git a/drivers/tty/serial/qcom_geni_serial.c b/drivers/tty/serial/qcom_geni_serial.c
index bd03b998ed04..132669a2da34 100644
--- a/drivers/tty/serial/qcom_geni_serial.c
+++ b/drivers/tty/serial/qcom_geni_serial.c
@@ -391,7 +391,6 @@  static int qcom_geni_serial_get_char(struct uart_port *uport)
 static void qcom_geni_serial_poll_put_char(struct uart_port *uport,
 							unsigned char c)
 {
-	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
 	qcom_geni_serial_setup_tx(uport, 1);
 	WARN_ON(!qcom_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
 						M_TX_FIFO_WATERMARK_EN, true));
@@ -435,7 +434,6 @@  __qcom_geni_serial_console_write(struct uart_port *uport, const char *s,
 			bytes_to_send++;
 	}
 
-	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
 	qcom_geni_serial_setup_tx(uport, bytes_to_send);
 	for (i = 0; i < count; ) {
 		size_t chars_to_write = 0;
@@ -663,7 +661,6 @@  static void qcom_geni_serial_start_tx_fifo(struct uart_port *uport)
 	irq_en = readl(uport->membase +	SE_GENI_M_IRQ_EN);
 	irq_en |= M_TX_FIFO_WATERMARK_EN | M_CMD_DONE_EN;
 
-	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
 	writel(irq_en, uport->membase +	SE_GENI_M_IRQ_EN);
 }
 
@@ -674,7 +671,6 @@  static void qcom_geni_serial_stop_tx_fifo(struct uart_port *uport)
 
 	irq_en = readl(uport->membase + SE_GENI_M_IRQ_EN);
 	irq_en &= ~(M_CMD_DONE_EN | M_TX_FIFO_WATERMARK_EN);
-	writel(0, uport->membase + SE_GENI_TX_WATERMARK_REG);
 	writel(irq_en, uport->membase + SE_GENI_M_IRQ_EN);
 	/* Possible stop tx is called multiple times. */
 	if (!qcom_geni_serial_main_active(uport))
@@ -1126,6 +1122,7 @@  static int qcom_geni_serial_port_setup(struct uart_port *uport)
 			       false, true, true);
 	geni_se_init(&port->se, UART_RX_WM, port->rx_fifo_depth - 2);
 	geni_se_select_mode(&port->se, port->dev_data->mode);
+	writel(DEF_TX_WM, uport->membase + SE_GENI_TX_WATERMARK_REG);
 	qcom_geni_serial_start_rx(uport);
 	port->setup = true;