| Message ID | 20240722-qx1050-feature-expansion-v1-6-c4d486435b96@riseup.net (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | F(x)tec Pro1X feature expansion | expand |
On 22.07.2024 9:10 AM, Dang Huynh wrote: > Fxtec Pro1x uses the same display (BOE BF060Y8M-AJ0) as Pro1. > > Signed-off-by: Dang Huynh <danct12@riseup.net> > --- [...] > + panel: panel@0 { > + compatible = "boe,bf060y8m-aj0"; > + reg = <0>; > + > + reset-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>; > + > + vddio-supply = <&pm6125_l9a>; > + > + pinctrl-names = "default"; > + pinctrl-0 = <&mdss_dsi_n &panel_en_n>; pinctrl-n pinctrl-names > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&mdss_dsi0_out>; > + }; > + }; > + }; > +}; > + > +&mdss_dsi0_out { > + data-lanes = <0 1 2 3>; > + remote-endpoint = <&panel_in>; > +}; > + > +&mdss_dsi0_phy { > + status = "okay"; No power supplies? Konrad
> > +&mdss_dsi0_phy { > > + status = "okay"; > > No power supplies? > > Konrad Doesn't seem to be defined anywhere on downstream, may be hardware controlled.
On 22.07.2024 11:17 AM, Dang Huynh wrote: >>> +&mdss_dsi0_phy { >>> + status = "okay"; >> >> No power supplies? >> >> Konrad > > Doesn't seem to be defined anywhere on downstream, may be hardware controlled. my downstream suggests L1b Konrad
diff --git a/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts b/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts index 42567545f56d..6148cc258164 100644 --- a/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts +++ b/arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts @@ -89,13 +89,16 @@ ts_vddio_supply: ts-vddio-supply { }; }; -&dispcc { - /* HACK: disable until a panel driver is ready to retain simplefb */ - status = "disabled"; +&gpi_dma0 { + status = "okay"; }; -&gpi_dma0 { +&gpu { status = "okay"; + + zap-shader { + firmware-name = "qcom/sm6115/Fxtec/QX1050/a610_zap.mbn"; + }; }; &i2c1 { @@ -132,6 +135,42 @@ touchscreen@14 { }; }; +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + vdda-supply = <&pm6125_l18a>; + status = "okay"; + + panel: panel@0 { + compatible = "boe,bf060y8m-aj0"; + reg = <0>; + + reset-gpios = <&tlmm 82 GPIO_ACTIVE_LOW>; + + vddio-supply = <&pm6125_l9a>; + + pinctrl-names = "default"; + pinctrl-0 = <&mdss_dsi_n &panel_en_n>; + + port { + panel_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + }; +}; + +&mdss_dsi0_out { + data-lanes = <0 1 2 3>; + remote-endpoint = <&panel_in>; +}; + +&mdss_dsi0_phy { + status = "okay"; +}; + &pm6125_gpios { vol_up_n: vol-up-n-state { pins = "gpio5"; @@ -340,6 +379,19 @@ key_camera_n: key-camera-n { bias-pull-up; }; + mdss_dsi_n: mdss-dsi-n { + pins = "gpio82"; + function = "gpio"; + drive-strength = <8>; + bias-disable; + }; + + panel_en_n: panel-en-n { + pins = "gpio65"; + function = "gpio"; + bias-disable; + }; + ts_int_n: ts-int-n { pins = "gpio80"; function = "gpio";
Fxtec Pro1x uses the same display (BOE BF060Y8M-AJ0) as Pro1. Signed-off-by: Dang Huynh <danct12@riseup.net> --- arch/arm64/boot/dts/qcom/sm6115-fxtec-pro1x.dts | 60 +++++++++++++++++++++++-- 1 file changed, 56 insertions(+), 4 deletions(-)