@@ -58,10 +58,13 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt86518.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt86528.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-wingtech-wt88047.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8916-yiming-uz801v3.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8929-wingtech-wt82918hd.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8939-huawei-kiwi.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8939-longcheer-l9100.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8939-samsung-a7.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8939-sony-xperia-kanuti-tulip.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8939-wingtech-wt82918.dtb
+dtb-$(CONFIG_ARCH_QCOM) += msm8939-wingtech-wt82918hd.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-motorola-potter.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-daisy.dtb
dtb-$(CONFIG_ARCH_QCOM) += msm8953-xiaomi-mido.dtb
new file mode 100644
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * msm8929-pm8916.dtsi describes common properties (e.g. regulator connections)
+ * that apply to most devices that make use of the MSM8929 SoC and PM8916 PMIC.
+ * Many regulators have a fixed purpose in the original reference design and
+ * were rarely re-used for different purposes. Devices that deviate from the
+ * typical reference design should not make use of this include and instead add
+ * the necessary properties in the board-specific device tree.
+ */
+
+#include "msm8929.dtsi"
+#include "pm8916.dtsi"
+
+&mdss_dsi0 {
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l6>;
+};
+
+&mdss_dsi0_phy {
+ vddio-supply = <&pm8916_l6>;
+};
+
+&mdss_dsi1 {
+ vdda-supply = <&pm8916_l2>;
+ vddio-supply = <&pm8916_l6>;
+};
+
+&mdss_dsi1_phy {
+ vddio-supply = <&pm8916_l6>;
+};
+
+&mpss {
+ pll-supply = <&pm8916_l7>;
+};
+
+&pm8916_codec {
+ vdd-cdc-io-supply = <&pm8916_l5>;
+ vdd-cdc-tx-rx-cx-supply = <&pm8916_l5>;
+ vdd-micbias-supply = <&pm8916_l13>;
+};
+
+&rpm_requests {
+ pm8916_rpm_regulators: regulators {
+ compatible = "qcom,rpm-pm8916-regulators";
+ vdd_l1_l2_l3-supply = <&pm8916_s3>;
+ vdd_l4_l5_l6-supply = <&pm8916_s4>;
+ vdd_l7-supply = <&pm8916_s4>;
+
+ /* pm8916_s1 is managed by rpmpd (MSM8939_VDDMDCX) */
+ /* pm8916_s2 is managed by rpmpd (MSM8939_VDDCX) */
+ pm8916_s3: s3 {
+ regulator-min-microvolt = <1250000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on; /* Needed for L2 */
+ };
+ pm8916_s4: s4 {
+ regulator-min-microvolt = <1850000>;
+ regulator-max-microvolt = <2150000>;
+ regulator-always-on; /* Needed for L5/L7 */
+ };
+
+ /*
+ * Some of the regulators are unused or managed by another
+ * processor (e.g. the modem). We should still define nodes for
+ * them to ensure the vote from the application processor can be
+ * dropped in case the regulators are already on during boot.
+ *
+ * The labels for these nodes are omitted on purpose because
+ * boards should configure a proper voltage before using them.
+ */
+ l1 {};
+
+ pm8916_l2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on; /* Needed for LPDDR RAM */
+ };
+
+ /* pm8916_l3 is managed by rpmpd (MSM8939_VDDMX) */
+
+ l4 {};
+
+ pm8916_l5: l5 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on; /* Needed for most digital I/O */
+ };
+
+ pm8916_l6: l6 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ pm8916_l7: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on; /* Needed for CPU PLL */
+ };
+
+ pm8916_l8: l8 {
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ };
+
+ pm8916_l9: l9 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ l10 {};
+
+ pm8916_l11: l11 {
+ regulator-min-microvolt = <2950000>;
+ regulator-max-microvolt = <2950000>;
+ regulator-allow-set-load;
+ regulator-system-load = <200000>;
+ };
+
+ pm8916_l12: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2950000>;
+ };
+
+ pm8916_l13: l13 {
+ regulator-min-microvolt = <3075000>;
+ regulator-max-microvolt = <3075000>;
+ };
+
+ l14 {};
+ l15 {};
+ l16 {};
+ l17 {};
+ l18 {};
+ };
+};
+
+&sdhc_1 {
+ vmmc-supply = <&pm8916_l8>;
+ vqmmc-supply = <&pm8916_l5>;
+};
+
+&sdhc_2 {
+ vmmc-supply = <&pm8916_l11>;
+ vqmmc-supply = <&pm8916_l12>;
+};
+
+&usb_hs_phy {
+ v1p8-supply = <&pm8916_l7>;
+ v3p3-supply = <&pm8916_l13>;
+};
+
+&wcnss {
+ vddpx-supply = <&pm8916_l7>;
+};
+
+&wcnss_iris {
+ vddxo-supply = <&pm8916_l7>;
+ vddrfa-supply = <&pm8916_s3>;
+ vddpa-supply = <&pm8916_l9>;
+ vdddig-supply = <&pm8916_l5>;
+};
+
new file mode 100644
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8929-pm8916.dtsi"
+#include "msm8939-wingtech-wt82918.dtsi"
+
+/ {
+ model = "Lenovo Vibe K5 (HD) (Wingtech WT82918)";
+ compatible = "wingtech,wt82918hd", "qcom,msm8929";
+ chassis-type = "handset";
+};
+
+&touchscreen {
+ touchscreen-size-x = <720>;
+ touchscreen-size-y = <1280>;
+};
new file mode 100644
@@ -0,0 +1,7 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8939.dtsi"
+
+&opp_table {
+ /delete-node/ opp-550000000;
+};
new file mode 100644
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8939-pm8916.dtsi"
+#include "msm8939-wingtech-wt82918.dtsi"
+
+/ {
+ model = "Lenovo Vibe K5 (Wingtech WT82918)";
+ compatible = "wingtech,wt82918", "qcom,msm8939";
+ chassis-type = "handset";
+};
+
+&touchscreen {
+ touchscreen-size-x = <1080>;
+ touchscreen-size-y = <1920>;
+};
new file mode 100644
@@ -0,0 +1,252 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-modem-qdsp6.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+
+/ {
+ aliases {
+ mmc0 = &sdhc_1; /* eMMC */
+ mmc1 = &sdhc_2; /* SD card */
+ serial0 = &blsp_uart2;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pm8916_pwm 0 100000>;
+ brightness-levels = <0 255>;
+ num-interpolated-steps = <255>;
+ default-brightness-level = <128>;
+ };
+
+ flash-led-controller {
+ compatible = "sgmicro,sgm3140";
+ enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+ flash-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&camera_front_flash_default>;
+ pinctrl-names = "default";
+
+ flash_led: led {
+ function = LED_FUNCTION_FLASH;
+ color = <LED_COLOR_ID_WHITE>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&gpio_keys_default>;
+ pinctrl-names = "default";
+
+ label = "GPIO Buttons";
+
+ button-volume-up {
+ label = "Volume Up";
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_VOLUMEUP>;
+ };
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ pinctrl-0 = <&gpio_leds_default>;
+ pinctrl-names = "default";
+
+ led-0 {
+ gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
+ function = LED_FUNCTION_CHARGING;
+ color = <LED_COLOR_ID_RED>;
+ default-state = "off";
+ retain-state-suspended;
+ };
+
+ led-1 {
+ gpios = <&tlmm 36 GPIO_ACTIVE_HIGH>;
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_GREEN>;
+ default-state = "off";
+ retain-state-suspended;
+ };
+ };
+
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb_id_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c2 {
+ status = "okay";
+
+ accelerometer@68 {
+ compatible = "invensense,icm20608";
+ reg = <0x68>;
+
+ interrupts-extended = <&tlmm 115 IRQ_TYPE_EDGE_FALLING>;
+
+ pinctrl-0 = <&accelerometer_default>;
+ pinctrl-names = "default";
+
+ vdd-supply = <&pm8916_l17>;
+ vddio-supply = <&pm8916_l6>;
+
+ mount-matrix = "-1", "0", "0",
+ "0", "1", "0",
+ "0", "0", "1";
+ };
+};
+
+&blsp_i2c5 {
+ status = "okay";
+
+ touchscreen: touchscreen@38 {
+ compatible = "edt,edt-ft5306";
+ reg = <0x38>;
+
+ interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-0 = <&touchscreen_default>;
+ pinctrl-names = "default";
+
+ vcc-supply = <&pm8916_l17>;
+ iovcc-supply = <&pm8916_l6>;
+
+ reset-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&blsp_uart2 {
+ status = "okay";
+};
+
+&mpss_mem {
+ reg = <0x0 0x86800000 0x0 0x5500000>;
+};
+
+&pm8916_pwm {
+ pinctrl-0 = <&pwm_out>;
+ pinctrl-names = "default";
+ status = "okay";
+};
+
+&pm8916_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+ status = "okay";
+};
+
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <2850000>;
+ regulator-max-microvolt = <2850000>;
+ };
+};
+
+&pm8916_vib {
+ status = "okay";
+};
+
+&sdhc_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_default>;
+ pinctrl-1 = <&sdc2_sleep>;
+ pinctrl-names = "default", "sleep";
+ non-removable;
+ status = "okay";
+};
+
+&usb {
+ extcon = <&usb_id>, <&usb_id>;
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
+
+&wcnss {
+ status = "okay";
+};
+
+&wcnss_iris {
+ compatible = "qcom,wcn3620";
+};
+
+&wcnss_mem {
+ status = "okay";
+};
+
+&tlmm {
+ accelerometer_default: accelerometer-default-state {
+ pins = "gpio115";
+ function = "gpio";
+ drive-strength = <6>;
+ bias-pull-up;
+ };
+
+ camera_front_flash_default: camera-front-flash-default-state {
+ pins = "gpio31", "gpio32";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ gpio_keys_default: gpio-keys-default-state {
+ pins = "gpio107";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ gpio_leds_default: gpio-leds-default-state {
+ pins = "gpio36", "gpio69";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ touchscreen_default: touchscreen-default-state {
+ reset-pins {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ touchscreen-pins {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ usb_id_default: usb-id-default-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&pm8916_mpps {
+ pwm_out: mpp4-state {
+ pins = "mpp4";
+ function = "digital";
+ power-source = <PM8916_MPP_VPH>;
+ output-low;
+ qcom,dtest = <1>;
+ };
+};
new file mode 100644
@@ -0,0 +1,17 @@
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8939-pm8916.dtsi"
+#include "msm8939-wingtech-wt82918.dtsi"
+
+/ {
+ model = "Lenovo Vibe K5 (HD) (Wingtech WT82918)";
+ compatible = "wingtech,wt82918hdhw39", "qcom,msm8939";
+ chassis-type = "handset";
+};
+
+&touchscreen {
+ touchscreen-size-x = <720>;
+ touchscreen-size-y = <1280>;
+};