| Message ID | 20240731191723.3050932-1-quic_abhinavk@quicinc.com (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
| Series | drm/msm/dpu: move dpu_encoder's connector assignment to atomic_enable() | expand |
On Wed, Jul 31, 2024 at 12:17:22PM GMT, Abhinav Kumar wrote: > For cases where the crtc's connectors_changed was set without enable/active > getting toggled , there is an atomic_enable() call followed by an > atomic_disable() but without an atomic_mode_set(). > > This results in a NULL ptr access for the dpu_encoder_get_drm_fmt() call in > the atomic_enable() as the dpu_encoder's connector was cleared in the > atomic_disable() but not re-assigned as there was no atomic_mode_set() call. > > Fix the NULL ptr access by moving the assignment for atomic_enable() and also > use drm_atomic_get_new_connector_for_encoder() to get the connector from > the atomic_state. > > Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support") > Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> > Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> > --- > drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 4 ++-- > 1 file changed, 2 insertions(+), 2 deletions(-) Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> # SM8350-HDK Thanks a lot!
diff --git a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c index 34c56e855af7..3b171bf227d1 100644 --- a/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c +++ b/drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c @@ -1171,8 +1171,6 @@ static void dpu_encoder_virt_atomic_mode_set(struct drm_encoder *drm_enc, cstate->num_mixers = num_lm; - dpu_enc->connector = conn_state->connector; - for (i = 0; i < dpu_enc->num_phys_encs; i++) { struct dpu_encoder_phys *phys = dpu_enc->phys_encs[i]; @@ -1270,6 +1268,8 @@ static void dpu_encoder_virt_atomic_enable(struct drm_encoder *drm_enc, dpu_enc->commit_done_timedout = false; + dpu_enc->connector = drm_atomic_get_new_connector_for_encoder(state, drm_enc); + cur_mode = &dpu_enc->base.crtc->state->adjusted_mode; dpu_enc->wide_bus_en = dpu_encoder_is_widebus_enabled(drm_enc);
For cases where the crtc's connectors_changed was set without enable/active getting toggled , there is an atomic_enable() call followed by an atomic_disable() but without an atomic_mode_set(). This results in a NULL ptr access for the dpu_encoder_get_drm_fmt() call in the atomic_enable() as the dpu_encoder's connector was cleared in the atomic_disable() but not re-assigned as there was no atomic_mode_set() call. Fix the NULL ptr access by moving the assignment for atomic_enable() and also use drm_atomic_get_new_connector_for_encoder() to get the connector from the atomic_state. Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support") Reported-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Suggested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com> --- drivers/gpu/drm/msm/disp/dpu1/dpu_encoder.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-)