| Message ID | 20241002022015.867031-7-alexey.klimov@linaro.org (mailing list archive) |
|---|---|
| State | New |
| Headers | show |
| Series | qrb4210-rb2: add HDMI audio playback support | expand |
On 02/10/2024 04:20, Alexey Klimov wrote: > This is required to enable to HDMI audio playback on > QRB4210 RB2 board. > > Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> > --- > arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 36 ++++++++++++++++++++++++ > 1 file changed, 36 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts > index 1888d99d398b..7731681688d5 100644 > --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts > +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts > @@ -634,6 +634,42 @@ sdc2_card_det_n: sd-card-det-n-state { > }; > }; > > +&lpass_tlmm { > + lpi_i2s2_active: lpi-i2s2-active-state { > + sck-pin { It does not look like you tested the DTS against bindings. Please run `make dtbs_check W=1` (see Documentation/devicetree/bindings/writing-schema.rst or https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/ for instructions). Best regards, Krzysztof
diff --git a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts index 1888d99d398b..7731681688d5 100644 --- a/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts +++ b/arch/arm64/boot/dts/qcom/qrb4210-rb2.dts @@ -634,6 +634,42 @@ sdc2_card_det_n: sd-card-det-n-state { }; }; +&lpass_tlmm { + lpi_i2s2_active: lpi-i2s2-active-state { + sck-pin { + pins = "gpio10"; + function = "i2s2_clk"; + bias-disable; + drive-strength = <8>; + output-high; + }; + + ws-pins { + pins = "gpio11"; + function = "i2s2_ws"; + bias-disable; + drive-strength = <8>; + output-high; + }; + + data-pins { + pins = "gpio12"; + function = "i2s2_data"; + bias-disable; + drive-strength = <8>; + output-high; + }; + + ext-mclk1 { + pins = "gpio18"; + function = "ext_mclk1_a"; + bias-disable; + drive-strength = <16>; + output-high; + }; + }; +}; + &uart3 { interrupts-extended = <&intc GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>, <&tlmm 11 IRQ_TYPE_LEVEL_HIGH>;
This is required to enable to HDMI audio playback on QRB4210 RB2 board. Signed-off-by: Alexey Klimov <alexey.klimov@linaro.org> --- arch/arm64/boot/dts/qcom/qrb4210-rb2.dts | 36 ++++++++++++++++++++++++ 1 file changed, 36 insertions(+)