diff mbox series

[1/3] arm64: dts: qcom: sdm845-xiaomi-beryllium-common: add touchscreen related nodes

Message ID 20241007-pocof1-touchscreen-support-v1-1-db31b21818c5@joelselvaraj.com (mailing list archive)
State New
Headers show
Series Add Xiaomi Poco F1 touchscreen support | expand

Commit Message

Joel Selvaraj via B4 Relay Oct. 8, 2024, 2:59 a.m. UTC 
From: Joel Selvaraj <joelselvaraj.oss@gmail.com>

Enable qupv3_id_1 and gpi_dma1 as they are required for configuring
touchscreen. Also add pinctrl configurations needed for touchscreen.
These are common for both the tianma and ebbg touchscreen variant.
In the subsequent patches, we will enable support for the Novatek NT36672a
touchscreen and FocalTech FT8719 touchscreen that are used in the Poco F1
Tianma and EBBG panel variant respectively. This is done in preparation
for that.

Signed-off-by: Joel Selvaraj <foss@joelselvaraj.com>
---
 .../dts/qcom/sdm845-xiaomi-beryllium-common.dtsi   | 39 ++++++++++++++++++++++
 1 file changed, 39 insertions(+)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
index 617b17b2d7d9d..6773a7ddb9a33 100644
--- a/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
+++ b/arch/arm64/boot/dts/qcom/sdm845-xiaomi-beryllium-common.dtsi
@@ -243,6 +243,10 @@  &gmu {
 	status = "okay";
 };
 
+&gpi_dma1 {
+	status = "okay";
+};
+
 &gpu {
 	status = "okay";
 
@@ -408,6 +412,10 @@  &qupv3_id_0 {
 	status = "okay";
 };
 
+&qupv3_id_1 {
+	status = "okay";
+};
+
 &sdhc_2 {
 	status = "okay";
 
@@ -513,6 +521,37 @@  sdc2_card_det_n: sd-card-det-n-state {
 		function = "gpio";
 		bias-pull-up;
 	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-pull-down;
+		input-enable;
+	};
+
+	ts_reset_default: ts-reset-default-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <16>;
+		output-high;
+	};
+
+	ts_int_sleep: ts-int-sleep-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+		input-enable;
+	};
+
+	ts_reset_sleep: ts-reset-sleep-state {
+		pins = "gpio32";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
 };
 
 &uart6 {