@@ -399,6 +399,65 @@ qfprom: efuse@780000 {
#size-cells = <1>;
};
+ sdhc_1: mmc@7c4000 {
+ compatible = "qcom,qcs615-sdhci", "qcom,sdhci-msm-v5";
+ reg = <0 0x7c4000 0 0x1000>,
+ <0 0x7c5000 0 0x1000>;
+ reg-names = "hc",
+ "cqhci";
+
+ interrupts = <GIC_SPI 641 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 644 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq",
+ "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC1_AHB_CLK>,
+ <&gcc GCC_SDCC1_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>,
+ <&gcc GCC_SDCC1_ICE_CORE_CLK>;
+ clock-names = "iface",
+ "core",
+ "xo",
+ "ice";
+
+ resets = <&gcc GCC_SDCC1_BCR>;
+
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&sdhc1_opp_table>;
+ iommus = <&apps_smmu 0x02c0 0x0>;
+ interconnects = <&aggre1_noc MASTER_SDCC_1 QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+ &config_noc SLAVE_SDCC_1 QCOM_ICC_TAG_ALWAYS>;
+ interconnect-names = "sdhc-ddr",
+ "cpu-sdhc";
+
+ bus-width = <8>;
+ qcom,dll-config = <0x000f642c>;
+ qcom,ddr-config = <0x80040868>;
+ supports-cqe;
+ dma-coherent;
+ mmc-ddr-1_8v;
+ mmc-hs200-1_8v;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ status = "disabled";
+
+ sdhc1_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_svs>;
+ };
+
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
+ };
+
qupv3_id_0: geniqup@8c0000 {
compatible = "qcom,geni-se-qup";
reg = <0x0 0x8c0000 0x0 0x6000>;
@@ -494,6 +553,145 @@ qup_uart0_rx: qup-uart0-rx-state {
pins = "gpio17";
function = "qup0";
};
+
+ sdc1_state_on: sdc1-on-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc1_state_off: sdc1-off-state {
+ clk-pins {
+ pins = "sdc1_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc1_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc1_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ rclk-pins {
+ pins = "sdc1_rclk";
+ bias-pull-down;
+ };
+ };
+
+ sdc2_state_on: sdc2-on-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <16>;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <10>;
+ };
+ };
+
+ sdc2_state_off: sdc2-off-state {
+ clk-pins {
+ pins = "sdc2_clk";
+ bias-disable;
+ drive-strength = <2>;
+ };
+
+ cmd-pins {
+ pins = "sdc2_cmd";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+
+ data-pins {
+ pins = "sdc2_data";
+ bias-pull-up;
+ drive-strength = <2>;
+ };
+ };
+ };
+
+ sdhc_2: mmc@8804000 {
+ compatible = "qcom,qcs615-sdhci","qcom,sdhci-msm-v5";
+ reg = <0x0 0x8804000 0x0 0x1000>;
+ reg-names = "hc";
+
+ interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 222 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "hc_irq",
+ "pwr_irq";
+
+ clocks = <&gcc GCC_SDCC2_AHB_CLK>,
+ <&gcc GCC_SDCC2_APPS_CLK>,
+ <&rpmhcc RPMH_CXO_CLK>;
+ clock-names = "iface",
+ "core",
+ "xo";
+
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ operating-points-v2 = <&sdhc2_opp_table>;
+ iommus = <&apps_smmu 0x02a0 0x0>;
+ resets = <&gcc GCC_SDCC2_BCR>;
+ interconnects = <&aggre1_noc MASTER_SDCC_2 QCOM_ICC_TAG_ALWAYS
+ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ALWAYS
+ &config_noc SLAVE_SDCC_2 QCOM_ICC_TAG_ALWAYS>;
+ interconnect-names = "sdhc-ddr",
+ "cpu-sdhc";
+
+ bus-width = <4>;
+ qcom,dll-config = <0x0007642c>;
+ qcom,ddr-config = <0x80040868>;
+ dma-coherent;
+ status = "disabled";
+
+ sdhc2_opp_table: opp-table {
+ compatible = "operating-points-v2";
+
+ opp-100000000 {
+ opp-hz = /bits/ 64 <100000000>;
+ required-opps = <&rpmhpd_opp_low_svs>;
+ };
+
+ opp-202000000 {
+ opp-hz = /bits/ 64 <202000000>;
+ required-opps = <&rpmhpd_opp_nom>;
+ };
+ };
};
dc_noc: interconnect@9160000 {
Add SD and emmc support to the QCS615 Ride platform. The SD controller and emmc controller of QCS615 are derived from SM6115. Include the relevant binding documents accordingly. Additionally, configure emmc-related and SD-related opp, power, and interconnect settings in the device tree. Signed-off-by: Yuanjie Yang <quic_yuanjiey@quicinc.com> --- arch/arm64/boot/dts/qcom/qcs615.dtsi | 198 +++++++++++++++++++++++++++ 1 file changed, 198 insertions(+)