| Message ID | 20241112-msm8917-v5-8-3ca34d33191b@mainlining.org (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add MSM8917/PM8937/Redmi 5A | expand |
On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: > From: Otto Pflüger <otto.pflueger@abscue.de> > > Add initial support for MSM8917 SoC. > > Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> > [reword commit, rebase, fix schema errors] > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> > --- > arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 +++++++++++++++++++++++++++++++++ > 1 file changed, 1974 insertions(+) > > diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi b/arch/arm64/boot/dts/qcom/msm8917.dtsi > new file mode 100644 > index 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 > --- /dev/null > +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi > @@ -0,0 +1,1974 @@ > [...] > + domain-idle-states { > + cluster_sleep_0: cluster-sleep-0 { > + compatible = "domain-idle-state"; > + arm,psci-suspend-param = <0x41000023>; > + entry-latency-us = <700>; > + exit-latency-us = <650>; > + min-residency-us = <1972>; > + }; > + > + cluster_sleep_1: cluster-sleep-1 { > + compatible = "domain-idle-state"; > + arm,psci-suspend-param = <0x41000043>; > + entry-latency-us = <240>; > + exit-latency-us = <280>; > + min-residency-us = <806>; > + }; I think my comment here is still open: This is strange, the deeper sleep state has lower timings than the previous one? > + > + cluster_sleep_2: cluster-sleep-2 { > + compatible = "domain-idle-state"; > + arm,psci-suspend-param = <0x41000053>; > + entry-latency-us = <700>; > + exit-latency-us = <1000>; > + min-residency-us = <6500>; > + }; > + }; > + > [...] > + restart@4ab000 { > + compatible = "qcom,pshold"; > + reg = <0x004ab000 0x4>; > + }; This one too: You have PSCI for shutting down, do you actually need this? > + > + tlmm: pinctrl@1000000 { > + compatible = "qcom,msm8917-pinctrl"; > + reg = <0x01000000 0x300000>; > + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + gpio-ranges = <&tlmm 0 0 134>; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + > [...] > + sdc1_clk_on: sdc1-clk-on-state { > + pins = "sdc1_clk"; > + bias-disable; > + drive-strength = <16>; > + }; > + > + sdc1_clk_off: sdc1-clk-off-state { > + pins = "sdc1_clk"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + sdc1_cmd_on: sdc1-cmd-on-state { > + pins = "sdc1_cmd"; > + bias-disable; > + drive-strength = <10>; > + }; > + > + sdc1_cmd_off: sdc1-cmd-off-state { > + pins = "sdc1_cmd"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + sdc1_data_on: sdc1-data-on-state { > + pins = "sdc1_data"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + sdc1_data_off: sdc1-data-off-state { > + pins = "sdc1_data"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > + sdc1_rclk_on: sdc1-rclk-on-state { > + pins = "sdc1_rclk"; > + bias-pull-down; > + }; > + > + sdc1_rclk_off: sdc1-rclk-off-state { > + pins = "sdc1_rclk"; > + bias-pull-down; > + }; > + > + sdc2_clk_on: sdc2-clk-on-state { > + pins = "sdc2_clk"; > + drive-strength = <16>; > + bias-disable; > + }; > + > + sdc2_clk_off: sdc2-clk-off-state { > + pins = "sdc2_clk"; > + bias-disable; > + drive-strength = <2>; > + }; > + > + sdc2_cmd_on: sdc2-cmd-on-state { > + pins = "sdc2_cmd"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + sdc2_cmd_off: sdc2-cmd-off-state { > + pins = "sdc2_cmd"; > + bias-pull-up; > + drive-strength = <2>; > + }; These are not referenced anywhere? Not here in the sdhc_X nodes, and also not in your msm8917-xiaomi-riva.dts. Would also recommend consolidating these to a single node like in msm8916.dtsi, see commit c943e4c58b2f ("arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl"). https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c943e4c58b2ffb0dcd497f8b12f284f5e8fc477e > + > + sdc2_cd_on: cd-on-state { > + pins = "gpio67"; > + function = "gpio"; > + drive-strength = <2>; > + bias-pull-up; > + }; > + > + sdc2_cd_off: cd-off-state { > + pins = "gpio67"; > + function = "gpio"; > + drive-strength = <2>; > + bias-disable; > + }; It does not make sense to have different on/off states for the card detect (CD) pin of the SD card. It needs to work even when the SD card is suspended so we can detect insertions/removals. Also should be placed in the board-specific DT part. See commit dfbda20dabaa ("arm64: dts: qcom: msm8916/39: Fix SD card detect pinctrl"). https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dfbda20dabaa1f284abd550035db5887384c8e4c > + > + sdc2_data_on: sdc2-data-on-state { > + pins = "sdc2_data"; > + bias-pull-up; > + drive-strength = <10>; > + }; > + > + sdc2_data_off: sdc2-data-off-state { > + pins = "sdc2_data"; > + bias-pull-up; > + drive-strength = <2>; > + }; > + > [...] > + blsp1_i2c4: i2c@78b8000 { > + compatible = "qcom,i2c-qup-v2.2.1"; > + reg = <0x078b8000 0x500>; > + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, > + <&gcc GCC_BLSP1_AHB_CLK>; > + clock-names = "core", "iface"; > + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; > + dma-names = "tx", "rx"; > + pinctrl-0 = <&blsp1_i2c4_default>; > + pinctrl-1 = <&blsp1_i2c4_sleep>; > + pinctrl-names = "default", "sleep"; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + blsp2_i2c5: i2c@7af5000 { This is actually blsp2_i2c1 if you look at the clock name below: > + compatible = "qcom,i2c-qup-v2.2.1"; > + reg = <0x07af5000 0x600>; > + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, here ^ But I realize now that the pinctrl functions are consecutively numbered without the BLSP number. Sorry for the confusion. Basically: - blsp1_i2c2 == blsp_i2c2 - blsp2_i2c1 == blsp_i2c5 Looking at some other examples upstream I guess you can choose between one of the following options: 1. msm8974/msm8976/msm8996/msm8998: Use &blspX_i2cY labels for the i2c@ node and pinctrl and only have the slightly confusing pinctrl function. E.g. this in msm8976.dtsi: /* 4 (not 6!) interfaces per QUP, BLSP2 indexes are numbered (n)+4 */ blsp2_i2c2_default: blsp2-i2c2-default-state { pins = "gpio22", "gpio23"; function = "blsp_i2c6"; drive-strength = <2>; bias-disable; }; Note how blsp2_i2c2 == blsp_i2c6. 2. msm8994: Use &blspX_i2cY labels for the i2c@ node, but keep pinctrl named &i2cN_default. E.g. this in msm8994.dtsi: blsp2_i2c1: i2c@f9963000 { /* ... */ pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c7_default>; pinctrl-1 = <&i2c7_sleep>; /* ... */ }; Note how blsp2_i2c1 == i2c7_default here. 3. msm8953: Use &i2c_N labels everywhere like on downstream. E.g. this in msm8953.dtsi. This is pretty much what you had originally: i2c_5: i2c@7af5000 { /* ... */ pinctrl-names = "default", "sleep"; pinctrl-0 = <&i2c_5_default>; pinctrl-1 = <&i2c_5_sleep>; /* ... */ }; All of these are fine for me. Feel free to pick the one you prefer. But let's not introduce a new confusing variant of this. :-) Thanks, Stephan
On 2024-11-12 18:27, Stephan Gerhold wrote: > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: >> From: Otto Pflüger <otto.pflueger@abscue.de> >> >> Add initial support for MSM8917 SoC. >> >> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> >> [reword commit, rebase, fix schema errors] >> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> >> --- >> arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 >> +++++++++++++++++++++++++++++++++ >> 1 file changed, 1974 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi >> b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> new file mode 100644 >> index >> 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> @@ -0,0 +1,1974 @@ >> [...] >> + domain-idle-states { >> + cluster_sleep_0: cluster-sleep-0 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000023>; >> + entry-latency-us = <700>; >> + exit-latency-us = <650>; >> + min-residency-us = <1972>; >> + }; >> + >> + cluster_sleep_1: cluster-sleep-1 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000043>; >> + entry-latency-us = <240>; >> + exit-latency-us = <280>; >> + min-residency-us = <806>; >> + }; > > I think my comment here is still open: > > This is strange, the deeper sleep state has lower timings than the > previous one? > >> + >> + cluster_sleep_2: cluster-sleep-2 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000053>; >> + entry-latency-us = <700>; >> + exit-latency-us = <1000>; >> + min-residency-us = <6500>; >> + }; >> + }; >> + >> [...] >> + restart@4ab000 { >> + compatible = "qcom,pshold"; >> + reg = <0x004ab000 0x4>; >> + }; > > This one too: > > You have PSCI for shutting down, do you actually need this? Yes, power off is not working without this. > >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,msm8917-pinctrl"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + gpio-ranges = <&tlmm 0 0 134>; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> [...] >> + sdc1_clk_on: sdc1-clk-on-state { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <16>; >> + }; >> + >> + sdc1_clk_off: sdc1-clk-off-state { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_cmd_on: sdc1-cmd-on-state { >> + pins = "sdc1_cmd"; >> + bias-disable; >> + drive-strength = <10>; >> + }; >> + >> + sdc1_cmd_off: sdc1-cmd-off-state { >> + pins = "sdc1_cmd"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_data_on: sdc1-data-on-state { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc1_data_off: sdc1-data-off-state { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_rclk_on: sdc1-rclk-on-state { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + >> + sdc1_rclk_off: sdc1-rclk-off-state { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + >> + sdc2_clk_on: sdc2-clk-on-state { >> + pins = "sdc2_clk"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + sdc2_clk_off: sdc2-clk-off-state { >> + pins = "sdc2_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc2_cmd_on: sdc2-cmd-on-state { >> + pins = "sdc2_cmd"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc2_cmd_off: sdc2-cmd-off-state { >> + pins = "sdc2_cmd"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; > > These are not referenced anywhere? Not here in the sdhc_X nodes, and > also not in your msm8917-xiaomi-riva.dts. Would also recommend > consolidating these to a single node like in msm8916.dtsi, see commit > c943e4c58b2f ("arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl"). > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c943e4c58b2ffb0dcd497f8b12f284f5e8fc477e > >> + >> + sdc2_cd_on: cd-on-state { >> + pins = "gpio67"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-pull-up; >> + }; >> + >> + sdc2_cd_off: cd-off-state { >> + pins = "gpio67"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; > > It does not make sense to have different on/off states for the card > detect (CD) pin of the SD card. It needs to work even when the SD card > is suspended so we can detect insertions/removals. Also should be > placed > in the board-specific DT part. > > See commit dfbda20dabaa ("arm64: dts: qcom: msm8916/39: Fix SD card > detect pinctrl"). > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dfbda20dabaa1f284abd550035db5887384c8e4c > > >> + >> + sdc2_data_on: sdc2-data-on-state { >> + pins = "sdc2_data"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc2_data_off: sdc2-data-off-state { >> + pins = "sdc2_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> [...] >> + blsp1_i2c4: i2c@78b8000 { >> + compatible = "qcom,i2c-qup-v2.2.1"; >> + reg = <0x078b8000 0x500>; >> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, >> + <&gcc GCC_BLSP1_AHB_CLK>; >> + clock-names = "core", "iface"; >> + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; >> + dma-names = "tx", "rx"; >> + pinctrl-0 = <&blsp1_i2c4_default>; >> + pinctrl-1 = <&blsp1_i2c4_sleep>; >> + pinctrl-names = "default", "sleep"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + status = "disabled"; >> + }; >> + >> + blsp2_i2c5: i2c@7af5000 { > > This is actually blsp2_i2c1 if you look at the clock name below: > >> + compatible = "qcom,i2c-qup-v2.2.1"; >> + reg = <0x07af5000 0x600>; >> + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, > > here ^ > > But I realize now that the pinctrl functions are consecutively numbered > without the BLSP number. Sorry for the confusion. > > Basically: > - blsp1_i2c2 == blsp_i2c2 > - blsp2_i2c1 == blsp_i2c5 > > Looking at some other examples upstream I guess you can choose between > one of the following options: > > 1. msm8974/msm8976/msm8996/msm8998: Use &blspX_i2cY labels for the > i2c@ > node and pinctrl and only have the slightly confusing pinctrl > function. E.g. this in msm8976.dtsi: > > /* 4 (not 6!) interfaces per QUP, BLSP2 indexes are numbered (n)+4 > */ > blsp2_i2c2_default: blsp2-i2c2-default-state { > pins = "gpio22", "gpio23"; > function = "blsp_i2c6"; > drive-strength = <2>; > bias-disable; > }; > > Note how blsp2_i2c2 == blsp_i2c6. > > 2. msm8994: Use &blspX_i2cY labels for the i2c@ node, but keep pinctrl > named &i2cN_default. E.g. this in msm8994.dtsi: > > blsp2_i2c1: i2c@f9963000 { > /* ... */ > pinctrl-names = "default", "sleep"; > pinctrl-0 = <&i2c7_default>; > pinctrl-1 = <&i2c7_sleep>; > /* ... */ > }; > > Note how blsp2_i2c1 == i2c7_default here. > > 3. msm8953: Use &i2c_N labels everywhere like on downstream. E.g. this > in msm8953.dtsi. This is pretty much what you had originally: > > i2c_5: i2c@7af5000 { > /* ... */ > pinctrl-names = "default", "sleep"; > pinctrl-0 = <&i2c_5_default>; > pinctrl-1 = <&i2c_5_sleep>; > /* ... */ > }; > > All of these are fine for me. Feel free to pick the one you prefer. But > let's not introduce a new confusing variant of this. :-) > > Thanks, > Stephan
On 2024-11-12 18:27, Stephan Gerhold wrote: > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: >> From: Otto Pflüger <otto.pflueger@abscue.de> >> >> Add initial support for MSM8917 SoC. >> >> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> >> [reword commit, rebase, fix schema errors] >> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> >> --- >> arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 >> +++++++++++++++++++++++++++++++++ >> 1 file changed, 1974 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi >> b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> new file mode 100644 >> index >> 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> @@ -0,0 +1,1974 @@ >> [...] >> + domain-idle-states { >> + cluster_sleep_0: cluster-sleep-0 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000023>; >> + entry-latency-us = <700>; >> + exit-latency-us = <650>; >> + min-residency-us = <1972>; >> + }; >> + >> + cluster_sleep_1: cluster-sleep-1 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000043>; >> + entry-latency-us = <240>; >> + exit-latency-us = <280>; >> + min-residency-us = <806>; >> + }; > > I think my comment here is still open: > > This is strange, the deeper sleep state has lower timings than the > previous one? > >> + >> + cluster_sleep_2: cluster-sleep-2 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000053>; >> + entry-latency-us = <700>; >> + exit-latency-us = <1000>; >> + min-residency-us = <6500>; >> + }; >> + }; >> + >> [...] >> + restart@4ab000 { >> + compatible = "qcom,pshold"; >> + reg = <0x004ab000 0x4>; >> + }; > > This one too: > > You have PSCI for shutting down, do you actually need this? > >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,msm8917-pinctrl"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + gpio-ranges = <&tlmm 0 0 134>; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> [...] >> + sdc1_clk_on: sdc1-clk-on-state { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <16>; >> + }; >> + >> + sdc1_clk_off: sdc1-clk-off-state { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_cmd_on: sdc1-cmd-on-state { >> + pins = "sdc1_cmd"; >> + bias-disable; >> + drive-strength = <10>; >> + }; >> + >> + sdc1_cmd_off: sdc1-cmd-off-state { >> + pins = "sdc1_cmd"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_data_on: sdc1-data-on-state { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc1_data_off: sdc1-data-off-state { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_rclk_on: sdc1-rclk-on-state { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + >> + sdc1_rclk_off: sdc1-rclk-off-state { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + >> + sdc2_clk_on: sdc2-clk-on-state { >> + pins = "sdc2_clk"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + sdc2_clk_off: sdc2-clk-off-state { >> + pins = "sdc2_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc2_cmd_on: sdc2-cmd-on-state { >> + pins = "sdc2_cmd"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc2_cmd_off: sdc2-cmd-off-state { >> + pins = "sdc2_cmd"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; > > These are not referenced anywhere? Not here in the sdhc_X nodes, and > also not in your msm8917-xiaomi-riva.dts. Would also recommend > consolidating these to a single node like in msm8916.dtsi, see commit > c943e4c58b2f ("arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl"). > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c943e4c58b2ffb0dcd497f8b12f284f5e8fc477e > >> + >> + sdc2_cd_on: cd-on-state { >> + pins = "gpio67"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-pull-up; >> + }; >> + >> + sdc2_cd_off: cd-off-state { >> + pins = "gpio67"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; > > It does not make sense to have different on/off states for the card > detect (CD) pin of the SD card. It needs to work even when the SD card > is suspended so we can detect insertions/removals. Also should be > placed > in the board-specific DT part. I have made these based on this https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.9.6.2.r1-04800-89xx.0/arch/arm64/boot/dts/qcom/msm8917-pinctrl.dtsi > > See commit dfbda20dabaa ("arm64: dts: qcom: msm8916/39: Fix SD card > detect pinctrl"). > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dfbda20dabaa1f284abd550035db5887384c8e4c > > >> + >> + sdc2_data_on: sdc2-data-on-state { >> + pins = "sdc2_data"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc2_data_off: sdc2-data-off-state { >> + pins = "sdc2_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> [...] >> + blsp1_i2c4: i2c@78b8000 { >> + compatible = "qcom,i2c-qup-v2.2.1"; >> + reg = <0x078b8000 0x500>; >> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, >> + <&gcc GCC_BLSP1_AHB_CLK>; >> + clock-names = "core", "iface"; >> + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; >> + dma-names = "tx", "rx"; >> + pinctrl-0 = <&blsp1_i2c4_default>; >> + pinctrl-1 = <&blsp1_i2c4_sleep>; >> + pinctrl-names = "default", "sleep"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + status = "disabled"; >> + }; >> + >> + blsp2_i2c5: i2c@7af5000 { > > This is actually blsp2_i2c1 if you look at the clock name below: > >> + compatible = "qcom,i2c-qup-v2.2.1"; >> + reg = <0x07af5000 0x600>; >> + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, > > here ^ > > But I realize now that the pinctrl functions are consecutively numbered > without the BLSP number. Sorry for the confusion. > > Basically: > - blsp1_i2c2 == blsp_i2c2 > - blsp2_i2c1 == blsp_i2c5 > > Looking at some other examples upstream I guess you can choose between > one of the following options: > > 1. msm8974/msm8976/msm8996/msm8998: Use &blspX_i2cY labels for the > i2c@ > node and pinctrl and only have the slightly confusing pinctrl > function. E.g. this in msm8976.dtsi: > > /* 4 (not 6!) interfaces per QUP, BLSP2 indexes are numbered (n)+4 > */ > blsp2_i2c2_default: blsp2-i2c2-default-state { > pins = "gpio22", "gpio23"; > function = "blsp_i2c6"; > drive-strength = <2>; > bias-disable; > }; > > Note how blsp2_i2c2 == blsp_i2c6. > > 2. msm8994: Use &blspX_i2cY labels for the i2c@ node, but keep pinctrl > named &i2cN_default. E.g. this in msm8994.dtsi: > > blsp2_i2c1: i2c@f9963000 { > /* ... */ > pinctrl-names = "default", "sleep"; > pinctrl-0 = <&i2c7_default>; > pinctrl-1 = <&i2c7_sleep>; > /* ... */ > }; > > Note how blsp2_i2c1 == i2c7_default here. > > 3. msm8953: Use &i2c_N labels everywhere like on downstream. E.g. this > in msm8953.dtsi. This is pretty much what you had originally: > > i2c_5: i2c@7af5000 { > /* ... */ > pinctrl-names = "default", "sleep"; > pinctrl-0 = <&i2c_5_default>; > pinctrl-1 = <&i2c_5_sleep>; > /* ... */ > }; > > All of these are fine for me. Feel free to pick the one you prefer. But > let's not introduce a new confusing variant of this. :-) > > Thanks, > Stephan
On 2024-11-12 18:27, Stephan Gerhold wrote: > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: >> From: Otto Pflüger <otto.pflueger@abscue.de> >> >> Add initial support for MSM8917 SoC. >> >> Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> >> [reword commit, rebase, fix schema errors] >> Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> >> --- >> arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 >> +++++++++++++++++++++++++++++++++ >> 1 file changed, 1974 insertions(+) >> >> diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi >> b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> new file mode 100644 >> index >> 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> @@ -0,0 +1,1974 @@ >> [...] >> + domain-idle-states { >> + cluster_sleep_0: cluster-sleep-0 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000023>; >> + entry-latency-us = <700>; >> + exit-latency-us = <650>; >> + min-residency-us = <1972>; >> + }; >> + >> + cluster_sleep_1: cluster-sleep-1 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000043>; >> + entry-latency-us = <240>; >> + exit-latency-us = <280>; >> + min-residency-us = <806>; >> + }; > > I think my comment here is still open: > > This is strange, the deeper sleep state has lower timings than the > previous one? I was reordering based on Konrad comments when i have renamed the nodes maybe it is not correct then. I am searching for how to validate these levels, i have find these https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/arch/arm64/boot/dts/qcom/msm8917-pm.dtsi#L45-91 Do you know where can i find psci-suspend-param-s? Should I also add wfi level? > >> + >> + cluster_sleep_2: cluster-sleep-2 { >> + compatible = "domain-idle-state"; >> + arm,psci-suspend-param = <0x41000053>; >> + entry-latency-us = <700>; >> + exit-latency-us = <1000>; >> + min-residency-us = <6500>; >> + }; >> + }; >> + >> [...] >> + restart@4ab000 { >> + compatible = "qcom,pshold"; >> + reg = <0x004ab000 0x4>; >> + }; > > This one too: > > You have PSCI for shutting down, do you actually need this? > >> + >> + tlmm: pinctrl@1000000 { >> + compatible = "qcom,msm8917-pinctrl"; >> + reg = <0x01000000 0x300000>; >> + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; >> + gpio-controller; >> + gpio-ranges = <&tlmm 0 0 134>; >> + #gpio-cells = <2>; >> + interrupt-controller; >> + #interrupt-cells = <2>; >> + >> [...] >> + sdc1_clk_on: sdc1-clk-on-state { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <16>; >> + }; >> + >> + sdc1_clk_off: sdc1-clk-off-state { >> + pins = "sdc1_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_cmd_on: sdc1-cmd-on-state { >> + pins = "sdc1_cmd"; >> + bias-disable; >> + drive-strength = <10>; >> + }; >> + >> + sdc1_cmd_off: sdc1-cmd-off-state { >> + pins = "sdc1_cmd"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_data_on: sdc1-data-on-state { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc1_data_off: sdc1-data-off-state { >> + pins = "sdc1_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> + sdc1_rclk_on: sdc1-rclk-on-state { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + >> + sdc1_rclk_off: sdc1-rclk-off-state { >> + pins = "sdc1_rclk"; >> + bias-pull-down; >> + }; >> + >> + sdc2_clk_on: sdc2-clk-on-state { >> + pins = "sdc2_clk"; >> + drive-strength = <16>; >> + bias-disable; >> + }; >> + >> + sdc2_clk_off: sdc2-clk-off-state { >> + pins = "sdc2_clk"; >> + bias-disable; >> + drive-strength = <2>; >> + }; >> + >> + sdc2_cmd_on: sdc2-cmd-on-state { >> + pins = "sdc2_cmd"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc2_cmd_off: sdc2-cmd-off-state { >> + pins = "sdc2_cmd"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; > > These are not referenced anywhere? Not here in the sdhc_X nodes, and > also not in your msm8917-xiaomi-riva.dts. Would also recommend > consolidating these to a single node like in msm8916.dtsi, see commit > c943e4c58b2f ("arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl"). > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c943e4c58b2ffb0dcd497f8b12f284f5e8fc477e > >> + >> + sdc2_cd_on: cd-on-state { >> + pins = "gpio67"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-pull-up; >> + }; >> + >> + sdc2_cd_off: cd-off-state { >> + pins = "gpio67"; >> + function = "gpio"; >> + drive-strength = <2>; >> + bias-disable; >> + }; > > It does not make sense to have different on/off states for the card > detect (CD) pin of the SD card. It needs to work even when the SD card > is suspended so we can detect insertions/removals. Also should be > placed > in the board-specific DT part. > > See commit dfbda20dabaa ("arm64: dts: qcom: msm8916/39: Fix SD card > detect pinctrl"). > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dfbda20dabaa1f284abd550035db5887384c8e4c > > >> + >> + sdc2_data_on: sdc2-data-on-state { >> + pins = "sdc2_data"; >> + bias-pull-up; >> + drive-strength = <10>; >> + }; >> + >> + sdc2_data_off: sdc2-data-off-state { >> + pins = "sdc2_data"; >> + bias-pull-up; >> + drive-strength = <2>; >> + }; >> + >> [...] >> + blsp1_i2c4: i2c@78b8000 { >> + compatible = "qcom,i2c-qup-v2.2.1"; >> + reg = <0x078b8000 0x500>; >> + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, >> + <&gcc GCC_BLSP1_AHB_CLK>; >> + clock-names = "core", "iface"; >> + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; >> + dma-names = "tx", "rx"; >> + pinctrl-0 = <&blsp1_i2c4_default>; >> + pinctrl-1 = <&blsp1_i2c4_sleep>; >> + pinctrl-names = "default", "sleep"; >> + #address-cells = <1>; >> + #size-cells = <0>; >> + status = "disabled"; >> + }; >> + >> + blsp2_i2c5: i2c@7af5000 { > > This is actually blsp2_i2c1 if you look at the clock name below: > >> + compatible = "qcom,i2c-qup-v2.2.1"; >> + reg = <0x07af5000 0x600>; >> + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, > > here ^ > > But I realize now that the pinctrl functions are consecutively numbered > without the BLSP number. Sorry for the confusion. > > Basically: > - blsp1_i2c2 == blsp_i2c2 > - blsp2_i2c1 == blsp_i2c5 > > Looking at some other examples upstream I guess you can choose between > one of the following options: > > 1. msm8974/msm8976/msm8996/msm8998: Use &blspX_i2cY labels for the > i2c@ > node and pinctrl and only have the slightly confusing pinctrl > function. E.g. this in msm8976.dtsi: > > /* 4 (not 6!) interfaces per QUP, BLSP2 indexes are numbered (n)+4 > */ > blsp2_i2c2_default: blsp2-i2c2-default-state { > pins = "gpio22", "gpio23"; > function = "blsp_i2c6"; > drive-strength = <2>; > bias-disable; > }; > > Note how blsp2_i2c2 == blsp_i2c6. > > 2. msm8994: Use &blspX_i2cY labels for the i2c@ node, but keep pinctrl > named &i2cN_default. E.g. this in msm8994.dtsi: > > blsp2_i2c1: i2c@f9963000 { > /* ... */ > pinctrl-names = "default", "sleep"; > pinctrl-0 = <&i2c7_default>; > pinctrl-1 = <&i2c7_sleep>; > /* ... */ > }; > > Note how blsp2_i2c1 == i2c7_default here. > > 3. msm8953: Use &i2c_N labels everywhere like on downstream. E.g. this > in msm8953.dtsi. This is pretty much what you had originally: > > i2c_5: i2c@7af5000 { > /* ... */ > pinctrl-names = "default", "sleep"; > pinctrl-0 = <&i2c_5_default>; > pinctrl-1 = <&i2c_5_sleep>; > /* ... */ > }; > > All of these are fine for me. Feel free to pick the one you prefer. But > let's not introduce a new confusing variant of this. :-) > > Thanks, > Stephan
On Tue, Nov 12, 2024 at 06:38:04PM +0100, barnabas.czeman@mainlining.org wrote: > On 2024-11-12 18:27, Stephan Gerhold wrote: > > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: > > > From: Otto Pflüger <otto.pflueger@abscue.de> > > > > > > Add initial support for MSM8917 SoC. > > > > > > Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> > > > [reword commit, rebase, fix schema errors] > > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> > > > --- > > > arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 > > > +++++++++++++++++++++++++++++++++ > > > 1 file changed, 1974 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi > > > b/arch/arm64/boot/dts/qcom/msm8917.dtsi > > > new file mode 100644 > > > index 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 > > > --- /dev/null > > > +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi > > > @@ -0,0 +1,1974 @@ > [...] > > > + sdc1_clk_on: sdc1-clk-on-state { > > > + pins = "sdc1_clk"; > > > + bias-disable; > > > + drive-strength = <16>; > > > + }; > > > + > > > + sdc1_clk_off: sdc1-clk-off-state { > > > + pins = "sdc1_clk"; > > > + bias-disable; > > > + drive-strength = <2>; > > > + }; > > > + > > > + sdc1_cmd_on: sdc1-cmd-on-state { > > > + pins = "sdc1_cmd"; > > > + bias-disable; > > > + drive-strength = <10>; > > > + }; > > > + > > > + sdc1_cmd_off: sdc1-cmd-off-state { > > > + pins = "sdc1_cmd"; > > > + bias-disable; > > > + drive-strength = <2>; > > > + }; > > > + > > > + sdc1_data_on: sdc1-data-on-state { > > > + pins = "sdc1_data"; > > > + bias-pull-up; > > > + drive-strength = <10>; > > > + }; > > > + > > > + sdc1_data_off: sdc1-data-off-state { > > > + pins = "sdc1_data"; > > > + bias-pull-up; > > > + drive-strength = <2>; > > > + }; > > > + > > > + sdc1_rclk_on: sdc1-rclk-on-state { > > > + pins = "sdc1_rclk"; > > > + bias-pull-down; > > > + }; > > > + > > > + sdc1_rclk_off: sdc1-rclk-off-state { > > > + pins = "sdc1_rclk"; > > > + bias-pull-down; > > > + }; > > > + > > > + sdc2_clk_on: sdc2-clk-on-state { > > > + pins = "sdc2_clk"; > > > + drive-strength = <16>; > > > + bias-disable; > > > + }; > > > + > > > + sdc2_clk_off: sdc2-clk-off-state { > > > + pins = "sdc2_clk"; > > > + bias-disable; > > > + drive-strength = <2>; > > > + }; > > > + > > > + sdc2_cmd_on: sdc2-cmd-on-state { > > > + pins = "sdc2_cmd"; > > > + bias-pull-up; > > > + drive-strength = <10>; > > > + }; > > > + > > > + sdc2_cmd_off: sdc2-cmd-off-state { > > > + pins = "sdc2_cmd"; > > > + bias-pull-up; > > > + drive-strength = <2>; > > > + }; > > > > These are not referenced anywhere? Not here in the sdhc_X nodes, and > > also not in your msm8917-xiaomi-riva.dts. Would also recommend > > consolidating these to a single node like in msm8916.dtsi, see commit > > c943e4c58b2f ("arm64: dts: qcom: msm8916/39: Consolidate SDC pinctrl"). > > > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=c943e4c58b2ffb0dcd497f8b12f284f5e8fc477e > > > > > + > > > + sdc2_cd_on: cd-on-state { > > > + pins = "gpio67"; > > > + function = "gpio"; > > > + drive-strength = <2>; > > > + bias-pull-up; > > > + }; > > > + > > > + sdc2_cd_off: cd-off-state { > > > + pins = "gpio67"; > > > + function = "gpio"; > > > + drive-strength = <2>; > > > + bias-disable; > > > + }; > > > > It does not make sense to have different on/off states for the card > > detect (CD) pin of the SD card. It needs to work even when the SD card > > is suspended so we can detect insertions/removals. Also should be placed > > in the board-specific DT part. > I have made these based on this https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.9.6.2.r1-04800-89xx.0/arch/arm64/boot/dts/qcom/msm8917-pinctrl.dtsi Yes, msm8916-pinctrl.dtsi also has this in the downstream sources, but as I explain in the commit linked below I don't think this is right. You can probably just change it to bias-disable like I did for most of the boards. There is usually external pull up that keeps it working even in the "cd-off-state". > > > > See commit dfbda20dabaa ("arm64: dts: qcom: msm8916/39: Fix SD card > > detect pinctrl"). > > > > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=dfbda20dabaa1f284abd550035db5887384c8e4c > > Thanks, Stephan
On Tue, Nov 12, 2024 at 07:49:18PM +0100, barnabas.czeman@mainlining.org wrote: > On 2024-11-12 18:27, Stephan Gerhold wrote: > > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: > > > From: Otto Pflüger <otto.pflueger@abscue.de> > > > > > > Add initial support for MSM8917 SoC. > > > > > > Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> > > > [reword commit, rebase, fix schema errors] > > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> > > > --- > > > arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 > > > +++++++++++++++++++++++++++++++++ > > > 1 file changed, 1974 insertions(+) > > > > > > diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi > > > b/arch/arm64/boot/dts/qcom/msm8917.dtsi > > > new file mode 100644 > > > index 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 > > > --- /dev/null > > > +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi > > > @@ -0,0 +1,1974 @@ > > > [...] > > > + domain-idle-states { > > > + cluster_sleep_0: cluster-sleep-0 { > > > + compatible = "domain-idle-state"; > > > + arm,psci-suspend-param = <0x41000023>; > > > + entry-latency-us = <700>; > > > + exit-latency-us = <650>; > > > + min-residency-us = <1972>; > > > + }; > > > + > > > + cluster_sleep_1: cluster-sleep-1 { > > > + compatible = "domain-idle-state"; > > > + arm,psci-suspend-param = <0x41000043>; > > > + entry-latency-us = <240>; > > > + exit-latency-us = <280>; > > > + min-residency-us = <806>; > > > + }; > > > > I think my comment here is still open: > > > > This is strange, the deeper sleep state has lower timings than the > > previous one? > I was reordering based on Konrad comments when i have renamed the nodes > maybe it is not correct then. > I am searching for how to validate these levels, i have find these > https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/arch/arm64/boot/dts/qcom/msm8917-pm.dtsi#L45-91 I think you translated them correctly. It feels like downstream is weird or even wrong here. Usually a higher psci-mode (retention = 2, gdhs = 4) also implies a deeper idle state. But at some point the perf-l2-retention and perf-l2-gdhs state were swapped downstream: https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/dea262a17a9e80dacb86b7c2f269bcc7b4df3a13 I don't know if this is intended or just an oversight. If no one can clarify why this change was done I guess we can just choose between the following two options: 1. Describe it exactly like it was done downstream. In that case I would suggest swapping the node order back to what you had in v1. Even if that means that a lower idle state has the higher psci-mode (arm,psci-suspend-param). That should match what downstream did. OR 2. Omit cluster-sleep-0 and cluster-sleep-1. I doubt anyone will notice the minor difference in power consumption. The most important idle state is the deepest "power collapse" (PC) state. @Konrad: Do you have any opinion here? > Do you know where can i find psci-suspend-param-s? You need to translate it like in this code here: https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/drivers/cpuidle/lpm-levels.c#L1337-1340 Roughly described: - Set BIT(30) if the CPU state has qcom,is-reset - Affinity level is the hierarchy level that goes idle. In your case: CPU = 0, L2 cache/cluster = 1. Shift that to bit 24 (1 << 24 for cache/cluster) - For the state itself you need to combine the qcom,psci-cpu-mode and qcom,psci-mode according to the qcom,psci-mode-shift. E.g. for the "perf-l2-pc" state, combined with the deepest CPU state ("pc"): - BIT(30) is set because of qcom,is-reset - (1 << 24) because it's a L2 cache/cluster idle state - (qcom,psci-cpu-mode = <3>) << (qcom,psci-mode-shift = <0>) = (3 << 0) - (qcom,psci-mode = <5>) << (qcom,psci-mode-shift = <4>) = (5 << 4) All that combined: BIT(30) | (1 << 24) | (3 << 0) | (5 << 4) = 0x41000053 Which is what you have for cluster-sleep-2. The ones you have look correct to me. :-) > Should I also add wfi level? I think we usually omit those for the CPU at least. Not sure about the cache/cluster one. As I mentioned, at the end the most important idle state to have is the deepest ones. Those will get used during suspend and when you don't use the device. The others are more minor optimization for light usage, which will be less noticeable. Thanks, Stephan
On 2024-11-13 10:10, Stephan Gerhold wrote: > On Tue, Nov 12, 2024 at 07:49:18PM +0100, > barnabas.czeman@mainlining.org wrote: >> On 2024-11-12 18:27, Stephan Gerhold wrote: >> > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote: >> > > From: Otto Pflüger <otto.pflueger@abscue.de> >> > > >> > > Add initial support for MSM8917 SoC. >> > > >> > > Signed-off-by: Otto Pflüger <otto.pflueger@abscue.de> >> > > [reword commit, rebase, fix schema errors] >> > > Signed-off-by: Barnabás Czémán <barnabas.czeman@mainlining.org> >> > > --- >> > > arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974 >> > > +++++++++++++++++++++++++++++++++ >> > > 1 file changed, 1974 insertions(+) >> > > >> > > diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi >> > > b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> > > new file mode 100644 >> > > index 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 >> > > --- /dev/null >> > > +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi >> > > @@ -0,0 +1,1974 @@ >> > > [...] >> > > + domain-idle-states { >> > > + cluster_sleep_0: cluster-sleep-0 { >> > > + compatible = "domain-idle-state"; >> > > + arm,psci-suspend-param = <0x41000023>; >> > > + entry-latency-us = <700>; >> > > + exit-latency-us = <650>; >> > > + min-residency-us = <1972>; >> > > + }; >> > > + >> > > + cluster_sleep_1: cluster-sleep-1 { >> > > + compatible = "domain-idle-state"; >> > > + arm,psci-suspend-param = <0x41000043>; >> > > + entry-latency-us = <240>; >> > > + exit-latency-us = <280>; >> > > + min-residency-us = <806>; >> > > + }; >> > >> > I think my comment here is still open: >> > >> > This is strange, the deeper sleep state has lower timings than the >> > previous one? >> I was reordering based on Konrad comments when i have renamed the >> nodes >> maybe it is not correct then. >> I am searching for how to validate these levels, i have find these >> https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/arch/arm64/boot/dts/qcom/msm8917-pm.dtsi#L45-91 > > I think you translated them correctly. It feels like downstream is > weird > or even wrong here. Usually a higher psci-mode (retention = 2, gdhs = > 4) > also implies a deeper idle state. But at some point the > perf-l2-retention and perf-l2-gdhs state were swapped downstream: > > https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/dea262a17a9e80dacb86b7c2f269bcc7b4df3a13 > > I don't know if this is intended or just an oversight. If no one can > clarify why this change was done I guess we can just choose between the > following two options: > > 1. Describe it exactly like it was done downstream. In that case I > would suggest swapping the node order back to what you had in v1. > Even if that means that a lower idle state has the higher psci-mode > (arm,psci-suspend-param). That should match what downstream did. > > OR > > 2. Omit cluster-sleep-0 and cluster-sleep-1. I doubt anyone will > notice > the minor difference in power consumption. The most important idle > state is the deepest "power collapse" (PC) state. > > @Konrad: Do you have any opinion here? > >> Do you know where can i find psci-suspend-param-s? > > You need to translate it like in this code here: > https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/drivers/cpuidle/lpm-levels.c#L1337-1340 > > Roughly described: > - Set BIT(30) if the CPU state has qcom,is-reset > - Affinity level is the hierarchy level that goes idle. > In your case: CPU = 0, L2 cache/cluster = 1. > Shift that to bit 24 (1 << 24 for cache/cluster) > - For the state itself you need to combine the qcom,psci-cpu-mode and > qcom,psci-mode according to the qcom,psci-mode-shift. > > E.g. for the "perf-l2-pc" state, combined with the deepest CPU state > ("pc"): > > - BIT(30) is set because of qcom,is-reset > - (1 << 24) because it's a L2 cache/cluster idle state > - (qcom,psci-cpu-mode = <3>) << (qcom,psci-mode-shift = <0>) = (3 << > 0) > - (qcom,psci-mode = <5>) << (qcom,psci-mode-shift = <4>) = (5 << 4) > > All that combined: BIT(30) | (1 << 24) | (3 << 0) | (5 << 4) > = 0x41000053 > Thanks a lot this is a very useful description. > Which is what you have for cluster-sleep-2. The ones you have look > correct to me. :-) > >> Should I also add wfi level? > > I think we usually omit those for the CPU at least. Not sure about the > cache/cluster one. As I mentioned, at the end the most important idle > state to have is the deepest ones. Those will get used during suspend > and when you don't use the device. The others are more minor > optimization for light usage, which will be less noticeable. > > Thanks, > Stephan
diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi b/arch/arm64/boot/dts/qcom/msm8917.dtsi new file mode 100644 index 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50 --- /dev/null +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi @@ -0,0 +1,1974 @@ +// SPDX-License-Identifier: GPL-2.0-only + +#include <dt-bindings/clock/qcom,gcc-msm8917.h> +#include <dt-bindings/clock/qcom,rpmcc.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/power/qcom-rpmpd.h> +#include <dt-bindings/soc/qcom,apr.h> +#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h> +#include <dt-bindings/thermal/thermal.h> + +/ { + interrupt-parent = <&intc>; + + #address-cells = <2>; + #size-cells = <2>; + + chosen { }; + + clocks { + sleep_clk: sleep-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + xo_board: xo-board { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu@100 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x100>; + next-level-cache = <&l2_0>; + enable-method = "psci"; + clocks = <&apcs>; + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + power-domains = <&cpu_pd0>; + power-domain-names = "psci"; + }; + + l2_0: l2-cache { + compatible = "cache"; + cache-level = <2>; + cache-unified; + }; + + cpu1: cpu@101 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x101>; + next-level-cache = <&l2_0>; + enable-method = "psci"; + clocks = <&apcs>; + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + power-domains = <&cpu_pd1>; + power-domain-names = "psci"; + }; + + cpu2: cpu@102 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x102>; + next-level-cache = <&l2_0>; + enable-method = "psci"; + clocks = <&apcs>; + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + power-domains = <&cpu_pd2>; + power-domain-names = "psci"; + }; + + cpu3: cpu@103 { + device_type = "cpu"; + compatible = "arm,cortex-a53"; + reg = <0x103>; + next-level-cache = <&l2_0>; + enable-method = "psci"; + clocks = <&apcs>; + operating-points-v2 = <&cpu_opp_table>; + #cooling-cells = <2>; + power-domains = <&cpu_pd3>; + power-domain-names = "psci"; + }; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + + core1 { + cpu = <&cpu1>; + }; + + core2 { + cpu = <&cpu2>; + }; + + core3 { + cpu = <&cpu3>; + }; + }; + }; + + domain-idle-states { + cluster_sleep_0: cluster-sleep-0 { + compatible = "domain-idle-state"; + arm,psci-suspend-param = <0x41000023>; + entry-latency-us = <700>; + exit-latency-us = <650>; + min-residency-us = <1972>; + }; + + cluster_sleep_1: cluster-sleep-1 { + compatible = "domain-idle-state"; + arm,psci-suspend-param = <0x41000043>; + entry-latency-us = <240>; + exit-latency-us = <280>; + min-residency-us = <806>; + }; + + cluster_sleep_2: cluster-sleep-2 { + compatible = "domain-idle-state"; + arm,psci-suspend-param = <0x41000053>; + entry-latency-us = <700>; + exit-latency-us = <1000>; + min-residency-us = <6500>; + }; + }; + + idle-states { + entry-method = "psci"; + + cpu_sleep_0: cpu-sleep-0 { + compatible = "arm,idle-state"; + idle-state-name = "standalone-power-collapse"; + arm,psci-suspend-param = <0x40000003>; + entry-latency-us = <125>; + exit-latency-us = <180>; + min-residency-us = <595>; + local-timer-stop; + }; + }; + + cpu_opp_table: opp-table-cpu { + compatible = "operating-points-v2"; + opp-shared; + + opp-960000000 { + opp-hz = /bits/ 64 <960000000>; + }; + + opp-1094400000 { + opp-hz = /bits/ 64 <1094400000>; + }; + + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + }; + + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + }; + }; + }; + + firmware { + scm: scm { + compatible = "qcom,scm-msm8916", "qcom,scm"; + clocks = <&gcc GCC_CRYPTO_CLK>, + <&gcc GCC_CRYPTO_AXI_CLK>, + <&gcc GCC_CRYPTO_AHB_CLK>; + clock-names = "core", "bus", "iface"; + #reset-cells = <1>; + + qcom,dload-mode = <&tcsr 0x6100>; + }; + }; + + memory@80000000 { + device_type = "memory"; + /* We expect the bootloader to fill in the reg */ + reg = <0 0x80000000 0 0>; + }; + + pmu { + compatible = "arm,cortex-a53-pmu"; + interrupts = <GIC_PPI 7 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + }; + + psci { + compatible = "arm,psci-1.0"; + method = "smc"; + + cluster_pd: power-domain-cluster { + #power-domain-cells = <0>; + domain-idle-states = <&cluster_sleep_0>, + <&cluster_sleep_1>, + <&cluster_sleep_2>; + }; + + cpu_pd0: power-domain-cpu0 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd>; + domain-idle-states = <&cpu_sleep_0>; + }; + + cpu_pd1: power-domain-cpu1 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd>; + domain-idle-states = <&cpu_sleep_0>; + }; + + cpu_pd2: power-domain-cpu2 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd>; + domain-idle-states = <&cpu_sleep_0>; + }; + + cpu_pd3: power-domain-cpu3 { + #power-domain-cells = <0>; + power-domains = <&cluster_pd>; + domain-idle-states = <&cpu_sleep_0>; + }; + }; + + rpm: remoteproc { + compatible = "qcom,msm8917-rpm-proc", "qcom,rpm-proc"; + + smd-edge { + interrupts = <GIC_SPI 168 IRQ_TYPE_EDGE_RISING>; + qcom,ipc = <&apcs 8 0>; + qcom,smd-edge = <15>; + + rpm_requests: rpm-requests { + compatible = "qcom,rpm-msm8917", "qcom,smd-rpm"; + qcom,smd-channels = "rpm_requests"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-msm8917", "qcom,rpmcc"; + #clock-cells = <1>; + clocks = <&xo_board>; + clock-names = "xo"; + }; + + rpmpd: power-controller { + compatible = "qcom,msm8917-rpmpd"; + #power-domain-cells = <1>; + operating-points-v2 = <&rpmpd_opp_table>; + + rpmpd_opp_table: opp-table { + compatible = "operating-points-v2"; + + rpmpd_opp_ret: opp1 { + opp-level = <RPM_SMD_LEVEL_RETENTION>; + }; + + rpmpd_opp_ret_plus: opp2 { + opp-level = <RPM_SMD_LEVEL_RETENTION_PLUS>; + }; + + rpmpd_opp_min_svs: opp3 { + opp-level = <RPM_SMD_LEVEL_MIN_SVS>; + }; + + rpmpd_opp_low_svs: opp4 { + opp-level = <RPM_SMD_LEVEL_LOW_SVS>; + }; + + rpmpd_opp_svs: opp5 { + opp-level = <RPM_SMD_LEVEL_SVS>; + }; + + rpmpd_opp_svs_plus: opp6 { + opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; + }; + + rpmpd_opp_nom: opp7 { + opp-level = <RPM_SMD_LEVEL_NOM>; + }; + + rpmpd_opp_nom_plus: opp8 { + opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; + }; + + rpmpd_opp_turbo: opp9 { + opp-level = <RPM_SMD_LEVEL_TURBO>; + }; + }; + }; + }; + }; + }; + + reserved-memory { + #address-cells = <2>; + #size-cells = <2>; + ranges; + + qseecom_mem: qseecom@85b00000 { + reg = <0x0 0x85b00000 0x0 0x800000>; + no-map; + }; + + smem@86300000 { + compatible = "qcom,smem"; + reg = <0x0 0x86300000 0x0 0x100000>; + no-map; + + hwlocks = <&tcsr_mutex 3>; + qcom,rpm-msg-ram = <&rpm_msg_ram>; + }; + + reserved@86400000 { + reg = <0x0 0x86400000 0x0 0x400000>; + no-map; + }; + + rmtfs@92100000 { + compatible = "qcom,rmtfs-mem"; + reg = <0x0 0x92100000 0x0 0x180000>; + no-map; + + qcom,client-id = <1>; + }; + + adsp_mem: adsp { + size = <0x0 0x1100000>; + alignment = <0x0 0x100000>; + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>; + no-map; + status = "disabled"; + }; + + mba_mem: mba { + size = <0x0 0x100000>; + alignment = <0x0 0x100000>; + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>; + no-map; + status = "disabled"; + }; + + venus_mem: venus { + size = <0x0 0x400000>; + alignment = <0x0 0x100000>; + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>; + no-map; + status = "disabled"; + }; + + wcnss_mem: wcnss { + size = <0x0 0x700000>; + alignment = <0x0 0x100000>; + alloc-ranges = <0x0 0x86800000 0x0 0x8000000>; + no-map; + status = "disabled"; + }; + }; + + smp2p-adsp { + compatible = "qcom,smp2p"; + qcom,smem = <443>, <429>; + + interrupts = <GIC_SPI 291 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs 10>; + + qcom,local-pid = <0>; + qcom,remote-pid = <2>; + + adsp_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + adsp_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-modem { + compatible = "qcom,smp2p"; + qcom,smem = <435>, <428>; + + interrupts = <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs 14>; + + qcom,local-pid = <0>; + qcom,remote-pid = <1>; + + modem_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + modem_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smp2p-wcnss { + compatible = "qcom,smp2p"; + qcom,smem = <451>, <431>; + + interrupts = <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs 18>; + + qcom,local-pid = <0>; + qcom,remote-pid = <4>; + + wcnss_smp2p_out: master-kernel { + qcom,entry-name = "master-kernel"; + + #qcom,smem-state-cells = <1>; + }; + + wcnss_smp2p_in: slave-kernel { + qcom,entry-name = "slave-kernel"; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + smsm { + compatible = "qcom,smsm"; + + #address-cells = <1>; + #size-cells = <0>; + + mboxes = <0>, <&apcs 13>, <0>, <&apcs 19>; + + apps_smsm: apps@0 { + reg = <0>; + + #qcom,smem-state-cells = <1>; + }; + + hexagon_smsm: hexagon@1 { + reg = <1>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + wcnss_smsm: wcnss@6 { + reg = <6>; + interrupts = <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + }; + + soc: soc@0 { + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0 0xffffffff>; + compatible = "simple-bus"; + + rpm_msg_ram: sram@60000 { + compatible = "qcom,rpm-msg-ram"; + reg = <0x00060000 0x8000>; + }; + + usb_hs_phy: phy@6c000 { + compatible = "qcom,usb-hs-28nm-femtophy"; + reg = <0x0006c000 0x200>; + #phy-cells = <0>; + clocks = <&xo_board>, + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, + <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "ahb", "sleep"; + resets = <&gcc GCC_QUSB2_PHY_BCR>, + <&gcc GCC_USB2_HS_PHY_ONLY_BCR>; + reset-names = "phy", "por"; + status = "disabled"; + }; + + qfprom: qfprom@a4000 { + compatible = "qcom,msm8917-qfprom", "qcom,qfprom"; + reg = <0x000a4000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + + tsens_base1: base1@1d8 { + reg = <0x1d8 1>; + bits = <0 8>; + }; + + tsens_s5_p1: s5-p1@1d9 { + reg = <0x1d9 1>; + bits = <0 6>; + }; + + tsens_s5_p2: s5-p2@1d9 { + reg = <0x1d9 2>; + bits = <6 6>; + }; + + tsens_s6_p1: s6-p1@1da { + reg = <0x1da 2>; + bits = <4 6>; + }; + + tsens_s6_p2: s6-p2@1db { + reg = <0x1db 1>; + bits = <2 6>; + }; + + tsens_s7_p1: s7-p1@1dc { + reg = <0x1dc 1>; + bits = <0 6>; + }; + + tsens_s7_p2: s7-p2@1dc { + reg = <0x1dc 2>; + bits = <6 6>; + }; + + tsens_s8_p1: s8-p1@1dd { + reg = <0x1dd 2>; + bits = <4 6>; + }; + + tsens_s8_p2: s8-p2@1de { + reg = <0x1de 1>; + bits = <2 6>; + }; + + tsens_base2: base2@1df { + reg = <0x1df 1>; + bits = <0 8>; + }; + + tsens_mode: mode@210 { + reg = <0x210 1>; + bits = <0 3>; + }; + + tsens_s0_p1: s0-p1@210 { + reg = <0x210 2>; + bits = <3 6>; + }; + + tsens_s0_p2: s0-p2@211 { + reg = <0x211 1>; + bits = <1 6>; + }; + + tsens_s1_p1: s1-p1@211 { + reg = <0x211 2>; + bits = <7 6>; + }; + + tsens_s1_p2: s1-p2@212 { + reg = <0x212 2>; + bits = <5 6>; + }; + + tsens_s2_p1: s2-p1@213 { + reg = <0x213 2>; + bits = <3 6>; + }; + + tsens_s2_p2: s2-p2@214 { + reg = <0x214 1>; + bits = <1 6>; + }; + + tsens_s3_p1: s3-p1@214 { + reg = <0x214 2>; + bits = <7 6>; + }; + + tsens_s3_p2: s3-p2@215 { + reg = <0x215 2>; + bits = <5 6>; + }; + + tsens_s4_p1: s4-p1@216 { + reg = <0x216 2>; + bits = <3 6>; + }; + + tsens_s4_p2: s4-p2@217 { + reg = <0x217 1>; + bits = <1 6>; + }; + + tsens_s9_p1: s9-p1@230{ + reg = <0x230 1>; + bits = <0 6>; + }; + + tsens_s9_p2: s9-p2@230 { + reg = <0x230 2>; + bits = <6 6>; + }; + + tsens_s10_p1: s10-p1@231 { + reg = <0x231 2>; + bits = <4 6>; + }; + + tsens_s10_p2: s10-p2@232 { + reg = <0x232 1>; + bits = <2 6>; + }; + }; + + rng@e3000 { + compatible = "qcom,prng"; + reg = <0x000e3000 0x1000>; + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "core"; + }; + + tsens: thermal-sensor@4a9000 { + compatible = "qcom,msm8937-tsens", "qcom,tsens-v1"; + reg = <0x004a9000 0x1000>, + <0x004a8000 0x1000>; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "uplow"; + nvmem-cells = <&tsens_mode>, + <&tsens_base1>, <&tsens_base2>, + <&tsens_s0_p1>, <&tsens_s0_p2>, + <&tsens_s1_p1>, <&tsens_s1_p2>, + <&tsens_s2_p1>, <&tsens_s2_p2>, + <&tsens_s3_p1>, <&tsens_s3_p2>, + <&tsens_s4_p1>, <&tsens_s4_p2>, + <&tsens_s5_p1>, <&tsens_s5_p2>, + <&tsens_s6_p1>, <&tsens_s6_p2>, + <&tsens_s7_p1>, <&tsens_s7_p2>, + <&tsens_s8_p1>, <&tsens_s8_p2>, + <&tsens_s9_p1>, <&tsens_s9_p2>, + <&tsens_s10_p1>, <&tsens_s10_p2>; + nvmem-cell-names = "mode", + "base1", "base2", + "s0_p1", "s0_p2", + "s1_p1", "s1_p2", + "s2_p1", "s2_p2", + "s3_p1", "s3_p2", + "s4_p1", "s4_p2", + "s5_p1", "s5_p2", + "s6_p1", "s6_p2", + "s7_p1", "s7_p2", + "s8_p1", "s8_p2", + "s9_p1", "s9_p2", + "s10_p1", "s10_p2"; + #qcom,sensors = <11>; + #thermal-sensor-cells = <1>; + }; + + restart@4ab000 { + compatible = "qcom,pshold"; + reg = <0x004ab000 0x4>; + }; + + tlmm: pinctrl@1000000 { + compatible = "qcom,msm8917-pinctrl"; + reg = <0x01000000 0x300000>; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&tlmm 0 0 134>; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + + blsp1_i2c2_default: blsp1-i2c2-default-state { + pins = "gpio6", "gpio7"; + function = "blsp_i2c2"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c2_sleep: blsp1-i2c2-sleep-state { + pins = "gpio6", "gpio7"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c3_default: blsp1-i2c3-default-state { + pins = "gpio10", "gpio11"; + function = "blsp_i2c3"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c3_sleep: blsp1-i2c3-sleep-state { + pins = "gpio10", "gpio11"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c4_default: blsp1-i2c4-default-state { + pins = "gpio14", "gpio15"; + function = "blsp_i2c4"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_i2c4_sleep: blsp1-i2c4-sleep-state { + pins = "gpio14", "gpio15"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c5_default: i2c5-default-state { + pins = "gpio18", "gpio19"; + function = "blsp_i2c5"; + drive-strength = <2>; + bias-disable; + }; + + blsp2_i2c5_sleep: i2c5-sleep-state { + pins = "gpio18", "gpio19"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_spi3_default: blsp1-spi3-default-state { + cs-pins { + pins = "gpio10"; + function = "blsp_spi3"; + drive-strength = <2>; + bias-disable; + }; + + spi-pins { + pins = "gpio8", "gpio9", "gpio11"; + function = "blsp_spi3"; + drive-strength = <12>; + bias-disable; + }; + }; + + blsp1_spi3_sleep: blsp1-spi3-sleep-state { + cs-pins { + pins = "gpio10"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + spi-pins { + pins = "gpio8", "gpio9", "gpio11"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + blsp2_spi6_default: blsp2-spi6-default-state { + cs0-pins { + pins = "gpio47"; + function = "blsp_spi6"; + drive-strength = <16>; + bias-disable; + }; + + cs1-pins { + pins = "gpio22"; + function = "blsp_spi6"; + drive-strength = <16>; + bias-disable; + }; + + spi-pins { + pins = "gpio20", "gpio21", "gpio23"; + function = "blsp_spi6"; + drive-strength = <16>; + bias-disable; + }; + }; + + blsp2_spi6_sleep: blsp2-spi6-sleep-state { + cs0-pins { + pins = "gpio47"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + cs1-pins { + pins = "gpio22"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + spi-pins { + pins = "gpio20", "gpio21", "gpio23"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + blsp1_uart1_default: blsp1-uart1-default-state { + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + function = "blsp_uart1"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_uart1_sleep: blsp1-uart1-sleep-state { + pins = "gpio0", "gpio1", "gpio2", "gpio3"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_uart2_default: blsp1-uart2-default-state { + pins = "gpio4", "gpio5"; + function = "blsp_uart2"; + drive-strength = <2>; + bias-disable; + }; + + blsp1_uart2_sleep: blsp1-uart2-sleep-state { + pins = "gpio4", "gpio5"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + + sdc1_clk_on: sdc1-clk-on-state { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <16>; + }; + + sdc1_clk_off: sdc1-clk-off-state { + pins = "sdc1_clk"; + bias-disable; + drive-strength = <2>; + }; + + sdc1_cmd_on: sdc1-cmd-on-state { + pins = "sdc1_cmd"; + bias-disable; + drive-strength = <10>; + }; + + sdc1_cmd_off: sdc1-cmd-off-state { + pins = "sdc1_cmd"; + bias-disable; + drive-strength = <2>; + }; + + sdc1_data_on: sdc1-data-on-state { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sdc1_data_off: sdc1-data-off-state { + pins = "sdc1_data"; + bias-pull-up; + drive-strength = <2>; + }; + + sdc1_rclk_on: sdc1-rclk-on-state { + pins = "sdc1_rclk"; + bias-pull-down; + }; + + sdc1_rclk_off: sdc1-rclk-off-state { + pins = "sdc1_rclk"; + bias-pull-down; + }; + + sdc2_clk_on: sdc2-clk-on-state { + pins = "sdc2_clk"; + drive-strength = <16>; + bias-disable; + }; + + sdc2_clk_off: sdc2-clk-off-state { + pins = "sdc2_clk"; + bias-disable; + drive-strength = <2>; + }; + + sdc2_cmd_on: sdc2-cmd-on-state { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <10>; + }; + + sdc2_cmd_off: sdc2-cmd-off-state { + pins = "sdc2_cmd"; + bias-pull-up; + drive-strength = <2>; + }; + + sdc2_cd_on: cd-on-state { + pins = "gpio67"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + + sdc2_cd_off: cd-off-state { + pins = "gpio67"; + function = "gpio"; + drive-strength = <2>; + bias-disable; + }; + + sdc2_data_on: sdc2-data-on-state { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <10>; + }; + + sdc2_data_off: sdc2-data-off-state { + pins = "sdc2_data"; + bias-pull-up; + drive-strength = <2>; + }; + + wcnss_pin_a: wcnss-active-state { + wcss-wlan-pins { + pins = "gpio79", "gpio80"; + function = "wcss_wlan"; + drive-strength = <6>; + bias-pull-up; + + }; + + wcss-wlan0-pins { + pins = "gpio78"; + function = "wcss_wlan0"; + drive-strength = <6>; + bias-pull-up; + + }; + + wcss-wlan1-pins { + pins = "gpio77"; + function = "wcss_wlan1"; + drive-strength = <6>; + bias-pull-up; + + }; + + wcss-wlan2-pins { + pins = "gpio76"; + function = "wcss_wlan2"; + drive-strength = <6>; + bias-pull-up; + + }; + }; + }; + + gcc: clock-controller@1800000 { + compatible = "qcom,gcc-msm8917"; + #clock-cells = <1>; + #reset-cells = <1>; + #power-domain-cells = <1>; + reg = <0x01800000 0x80000>; + clocks = <&xo_board>, + <&sleep_clk>, + <&mdss_dsi0_phy 1>, + <&mdss_dsi0_phy 0>; + clock-names = "xo", + "sleep_clk", + "dsi0pll", + "dsi0pllbyte"; + }; + + tcsr_mutex: hwlock@1905000 { + compatible = "qcom,tcsr-mutex"; + reg = <0x01905000 0x20000>; + #hwlock-cells = <1>; + }; + + tcsr: syscon@1937000 { + compatible = "qcom,tcsr-msm8917", "syscon"; + reg = <0x01937000 0x30000>; + }; + + mdss: display-subsystem@1a00000 { + compatible = "qcom,mdss"; + reg = <0x01a00000 0x1000>, + <0x01ab0000 0x1040>; + reg-names = "mdss_phys", "vbif_phys"; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface", + "bus", + "vsync"; + + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + interrupt-controller; + #interrupt-cells = <1>; + + #address-cells = <1>; + #size-cells = <1>; + ranges; + + status = "disabled"; + + mdp: display-controller@1a01000 { + compatible = "qcom,msm8917-mdp5", "qcom,mdp5"; + reg = <0x01a01000 0x89000>; + reg-names = "mdp_phys"; + + interrupt-parent = <&mdss>; + interrupts = <0>; + + power-domains = <&gcc MDSS_GDSC>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_VSYNC_CLK>; + clock-names = "iface", + "bus", + "core", + "vsync"; + + iommus = <&apps_iommu 0x15>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mdp5_intf1_out: endpoint { + remote-endpoint = <&mdss_dsi0_in>; + }; + }; + }; + }; + + mdss_dsi0: dsi@1a94000 { + compatible = "qcom,mdss-dsi-ctrl"; + reg = <0x01a94000 0x300>; + reg-names = "dsi_ctrl"; + + interrupt-parent = <&mdss>; + interrupts = <4>; + + assigned-clocks = <&gcc BYTE0_CLK_SRC>, + <&gcc PCLK0_CLK_SRC>; + assigned-clock-parents = <&mdss_dsi0_phy 0>, + <&mdss_dsi0_phy 1>; + + clocks = <&gcc GCC_MDSS_MDP_CLK>, + <&gcc GCC_MDSS_AHB_CLK>, + <&gcc GCC_MDSS_AXI_CLK>, + <&gcc GCC_MDSS_BYTE0_CLK>, + <&gcc GCC_MDSS_PCLK0_CLK>, + <&gcc GCC_MDSS_ESC0_CLK>; + clock-names = "mdp_core", + "iface", + "bus", + "byte", + "pixel", + "core"; + phys = <&mdss_dsi0_phy>; + + operating-points-v2 = <&mdss_dsi0_opp_table>; + power-domains = <&rpmpd MSM8917_VDDCX>; + + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mdss_dsi0_in: endpoint { + remote-endpoint = <&mdp5_intf1_out>; + }; + }; + + port@1 { + reg = <1>; + + mdss_dsi0_out: endpoint { + }; + }; + }; + + mdss_dsi0_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-125000000 { + opp-hz = /bits/ 64 <125000000>; + required-opps = <&rpmpd_opp_svs>; + }; + + opp-187500000 { + opp-hz = /bits/ 64 <187500000>; + required-opps = <&rpmpd_opp_nom>; + }; + }; + }; + + mdss_dsi0_phy: phy@1a94a00 { + compatible = "qcom,dsi-phy-28nm-8937"; + reg = <0x01a94a00 0xd4>, + <0x01a94400 0x280>, + <0x01a94b80 0x30>; + reg-names = "dsi_pll", + "dsi_phy", + "dsi_phy_regulator"; + + #clock-cells = <1>; + #phy-cells = <0>; + + clocks = <&gcc GCC_MDSS_AHB_CLK>, + <&xo_board>; + clock-names = "iface", "ref"; + }; + }; + + apps_iommu: iommu@1e20000 { + #address-cells = <1>; + #size-cells = <1>; + #iommu-cells = <1>; + compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1"; + ranges = <0 0x01e20000 0x20000>; + + clocks = <&gcc GCC_SMMU_CFG_CLK>, + <&gcc GCC_APSS_TCU_CLK>; + clock-names = "iface", "bus"; + + qcom,iommu-secure-id = <17>; + + /* VFE */ + iommu-ctx@14000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x14000 0x1000>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; + }; + + /* MDP_0 */ + iommu-ctx@15000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x15000 0x1000>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; + }; + + /* VENUS_NS */ + iommu-ctx@16000 { + compatible = "qcom,msm-iommu-v1-ns"; + reg = <0x16000 0x1000>; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpu_iommu: iommu@1f08000 { + #address-cells = <1>; + #size-cells = <1>; + #iommu-cells = <1>; + + compatible = "qcom,msm8917-iommu", "qcom,msm-iommu-v1"; + + ranges = <0 0x01f08000 0x10000>; + clocks = <&gcc GCC_SMMU_CFG_CLK>, + <&gcc GCC_GFX_TCU_CLK>; + clock-names = "iface", "bus"; + qcom,iommu-secure-id = <18>; + + iommu-ctx@0 { + compatible = "qcom,msm-iommu-v2-ns"; + reg = <0 0x1000>; + interrupts = <GIC_SPI 240 IRQ_TYPE_LEVEL_HIGH>; + }; + }; + + gpu: gpu@1c00000 { + compatible = "qcom,adreno-306.32", "qcom,adreno"; + reg = <0x01c00000 0x20000>; + reg-names = "kgsl_3d0_reg_memory"; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "kgsl_3d0_irq"; + clock-names = "core", + "iface", + "mem_iface", + "alt_mem_iface", + "gfx3d"; + clocks = <&gcc GCC_OXILI_GFX3D_CLK>, + <&gcc GCC_OXILI_AHB_CLK>, + <&gcc GCC_BIMC_GFX_CLK>, + <&gcc GCC_BIMC_GPU_CLK>, + <&gcc GFX3D_CLK_SRC>; + power-domains = <&gcc OXILI_GX_GDSC>; + operating-points-v2 = <&gpu_opp_table>; + #cooling-cells = <2>; + + iommus = <&gpu_iommu 0>; + + status = "disabled"; + + gpu_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-598000000 { + opp-hz = /bits/ 64 <598000000>; + }; + + opp-523200000 { + opp-hz = /bits/ 64 <523200000>; + }; + + opp-484800000 { + opp-hz = /bits/ 64 <484800000>; + }; + + opp-400000000 { + opp-hz = /bits/ 64 <400000000>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + }; + + opp-19200000 { + opp-hz = /bits/ 64 <19200000>; + }; + }; + }; + + spmi_bus: spmi@200f000 { + compatible = "qcom,spmi-pmic-arb"; + reg = <0x0200f000 0x001000>, + <0x02400000 0x800000>, + <0x02c00000 0x800000>, + <0x03800000 0x200000>, + <0x0200a000 0x002100>; + reg-names = "core", + "chnls", + "obsrvr", + "intr", + "cnfg"; + interrupt-names = "periph_irq"; + interrupts = <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; + qcom,ee = <0>; + qcom,channel = <0>; + #address-cells = <2>; + #size-cells = <0>; + interrupt-controller; + #interrupt-cells = <4>; + }; + + bam_dmux_dma: dma-controller@4044000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x04044000 0x19000>; + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + qcom,ee = <0>; + + num-channels = <6>; + qcom,num-ees = <1>; + qcom,powered-remotely; + + status = "disabled"; + }; + + sdhc_1: mmc@7824900 { + compatible = "qcom,sdhci-msm-v4"; + reg = <0x07824900 0x500>, + <0x07824000 0x800>; + reg-names = "hc", "core"; + + interrupts = <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + clocks = <&gcc GCC_SDCC1_AHB_CLK>, + <&gcc GCC_SDCC1_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + power-domains = <&rpmpd MSM8917_VDDCX>; + mmc-hs200-1_8v; + mmc-hs400-1_8v; + mmc-ddr-1_8v; + bus-width = <8>; + non-removable; + status = "disabled"; + }; + + sdhc_2: mmc@7864900 { + compatible = "qcom,sdhci-msm-v4"; + reg = <0x07864900 0x500>, + <0x07864000 0x800>; + reg-names = "hc", "core"; + + interrupts = <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 221 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "hc_irq", "pwr_irq"; + clocks = <&gcc GCC_SDCC2_AHB_CLK>, + <&gcc GCC_SDCC2_APPS_CLK>, + <&xo_board>; + clock-names = "iface", "core", "xo"; + power-domains = <&rpmpd MSM8917_VDDCX>; + bus-width = <4>; + status = "disabled"; + }; + + blsp1_dma: dma-controller@7884000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x07884000 0x1f000>; + interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "bam_clk"; + qcom,controlled-remotely; + #dma-cells = <1>; + num-channels = <12>; + qcom,num-ees = <4>; + qcom,ee = <0>; + }; + + blsp2_dma: dma-controller@7ac4000 { + compatible = "qcom,bam-v1.7.0"; + reg = <0x07ac4000 0x1d000>; + interrupts = <GIC_SPI 239 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + qcom,controlled-remotely; + #dma-cells = <1>; + num-channels = <10>; + qcom,num-ees = <4>; + qcom,ee = <0>; + }; + + blsp1_uart1: serial@78af000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078af000 0x200>; + interrupts = <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART1_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 0>, <&blsp1_dma 1>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp1_uart1_default>; + pinctrl-1 = <&blsp1_uart1_sleep>; + pinctrl-names = "default", "sleep"; + status = "disabled"; + }; + + blsp1_uart2: serial@78b0000 { + compatible = "qcom,msm-uartdm-v1.4", "qcom,msm-uartdm"; + reg = <0x078b0000 0x200>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 2>, <&blsp1_dma 3>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp1_uart2_default>; + pinctrl-1 = <&blsp1_uart2_sleep>; + pinctrl-names = "default", "sleep"; + status = "disabled"; + }; + + blsp1_i2c2: i2c@78b6000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b6000 0x600>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP2_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 6>, <&blsp1_dma 7>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp1_i2c2_default>; + pinctrl-1 = <&blsp1_i2c2_sleep>; + pinctrl-names = "default", "sleep"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c3: i2c@78b7000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b7000 0x600>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP3_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp1_i2c3_default>; + pinctrl-1 = <&blsp1_i2c3_sleep>; + pinctrl-names = "default", "sleep"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_spi3: spi@78b7000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x078b7000 0x600>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP3_SPI_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 8>, <&blsp1_dma 9>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp1_spi3_default>; + pinctrl-1 = <&blsp1_spi3_sleep>; + pinctrl-names = "default", "sleep"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp1_i2c4: i2c@78b8000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x078b8000 0x500>; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP1_QUP4_I2C_APPS_CLK>, + <&gcc GCC_BLSP1_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp1_dma 10>, <&blsp1_dma 11>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp1_i2c4_default>; + pinctrl-1 = <&blsp1_i2c4_sleep>; + pinctrl-names = "default", "sleep"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_i2c5: i2c@7af5000 { + compatible = "qcom,i2c-qup-v2.2.1"; + reg = <0x07af5000 0x600>; + interrupts = <GIC_SPI 299 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_QUP1_I2C_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp2_dma 4>, <&blsp2_dma 5>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp2_i2c5_default>; + pinctrl-1 = <&blsp2_i2c5_sleep>; + pinctrl-names = "default", "sleep"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + blsp2_spi6: spi@7af6000 { + compatible = "qcom,spi-qup-v2.2.1"; + reg = <0x07af6000 0x600>; + interrupts = <GIC_SPI 300 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_BLSP2_QUP2_SPI_APPS_CLK>, + <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "core", "iface"; + dmas = <&blsp2_dma 6>, <&blsp2_dma 7>; + dma-names = "tx", "rx"; + pinctrl-0 = <&blsp2_spi6_default>; + pinctrl-1 = <&blsp2_spi6_sleep>; + pinctrl-names = "default", "sleep"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + usb: usb@78db000 { + compatible = "qcom,ci-hdrc"; + reg = <0x078db000 0x200>, + <0x078db200 0x200>; + interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gcc GCC_USB_HS_AHB_CLK>, + <&gcc GCC_USB_HS_SYSTEM_CLK>; + clock-names = "iface", "core"; + assigned-clocks = <&gcc GCC_USB_HS_SYSTEM_CLK>; + assigned-clock-rates = <80000000>; + resets = <&gcc GCC_USB_HS_BCR>; + reset-names = "core"; + phy_type = "ulpi"; + dr_mode = "otg"; + hnp-disable; + srp-disable; + adp-disable; + ahb-burst-config = <0>; + phy-names = "usb-phy"; + phys = <&usb_hs_phy>; + status = "disabled"; + #reset-cells = <1>; + }; + + wcnss: remoteproc@a204000 { + compatible = "qcom,pronto-v3-pil", "qcom,pronto"; + reg = <0x0a204000 0x2000>, + <0x0a202000 0x1000>, + <0x0a21b000 0x3000>; + reg-names = "ccu", "dxe", "pmu"; + + memory-region = <&wcnss_mem>; + + interrupts-extended = <&intc GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 0 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 1 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 2 IRQ_TYPE_EDGE_RISING>, + <&wcnss_smp2p_in 3 IRQ_TYPE_EDGE_RISING>; + interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack"; + + power-domains = <&rpmpd MSM8917_VDDCX>, + <&rpmpd MSM8917_VDDMX>; + power-domain-names = "cx", "mx"; + + qcom,smem-states = <&wcnss_smp2p_out 0>; + qcom,smem-state-names = "stop"; + + pinctrl-0 = <&wcnss_pin_a>; + pinctrl-names = "default"; + + status = "disabled"; + + wcnss_iris: iris { + clocks = <&rpmcc RPM_SMD_RF_CLK2>; + clock-names = "xo"; + }; + + smd-edge { + interrupts = <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>; + + mboxes = <&apcs 17>; + qcom,smd-edge = <6>; + qcom,remote-pid = <4>; + + label = "pronto"; + + wcnss_ctrl: wcnss { + compatible = "qcom,wcnss"; + qcom,smd-channels = "WCNSS_CTRL"; + + qcom,mmio = <&wcnss>; + + wcnss_bt: bluetooth { + compatible = "qcom,wcnss-bt"; + }; + + wcnss_wifi: wifi { + compatible = "qcom,wcnss-wlan"; + + interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "tx", "rx"; + + qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>; + qcom,smem-state-names = "tx-enable", + "tx-rings-empty"; + }; + }; + }; + }; + + intc: interrupt-controller@b000000 { + compatible = "qcom,msm-qgic2"; + interrupt-controller; + #interrupt-cells = <3>; + reg = <0x0b000000 0x1000>, + <0x0b002000 0x1000>; + }; + + apcs: mailbox@b011000 { + compatible = "qcom,msm8939-apcs-kpss-global", "syscon"; + reg = <0x0b011000 0x1000>; + #mbox-cells = <1>; + clocks = <&a53pll>, <&gcc GPLL0_EARLY>, <&rpmcc RPM_SMD_XO_CLK_SRC>; + clock-names = "pll", "aux", "ref"; + #clock-cells = <0>; + }; + + a53pll: clock@b016000 { + compatible = "qcom,msm8939-a53pll"; + reg = <0x0b016000 0x40>; + clocks = <&xo_board>; + clock-names = "xo"; + #clock-cells = <0>; + operating-points-v2 = <&pll_opp_table>; + + pll_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-960000000 { + opp-hz = /bits/ 64 <960000000>; + }; + + opp-1094400000 { + opp-hz = /bits/ 64 <1094400000>; + }; + + opp-1248000000 { + opp-hz = /bits/ 64 <1248000000>; + }; + + opp-1401600000 { + opp-hz = /bits/ 64 <1401600000>; + }; + }; + }; + + watchdog@b017000 { + compatible = "qcom,apss-wdt-qcs404", "qcom,kpss-wdt"; + reg = <0x0b017000 0x1000>; + clocks = <&sleep_clk>; + }; + + timer@b120000 { + #address-cells = <1>; + #size-cells = <1>; + ranges; + compatible = "arm,armv7-timer-mem"; + reg = <0x0b120000 0x1000>; + + frame@b121000 { + frame-number = <0>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b121000 0x1000>, + <0x0b122000 0x1000>; + }; + + frame@b123000 { + frame-number = <1>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b123000 0x1000>; + status = "disabled"; + }; + + frame@b124000 { + frame-number = <2>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b124000 0x1000>; + status = "disabled"; + }; + + frame@b125000 { + frame-number = <3>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b125000 0x1000>; + status = "disabled"; + }; + + frame@b126000 { + frame-number = <4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b126000 0x1000>; + status = "disabled"; + }; + + frame@b127000 { + frame-number = <5>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b127000 0x1000>; + status = "disabled"; + }; + + frame@b128000 { + frame-number = <6>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x0b128000 0x1000>; + status = "disabled"; + }; + }; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 4 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; + }; + + thermal_zones: thermal-zones { + aoss-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 0>; + + trips { + aoss_alert0: trip-point0 { + temperature = <85000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + camera-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 3>; + + trips { + camera_alert0: trip-point0 { + temperature = <85000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + cpuss1-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 4>; + + cooling-maps { + map0 { + trip = <&cpuss1_alert0>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + cpuss1_alert0: trip-point0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpuss1_alert1: trip-point1 { + temperature = <85000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpuss1_crit: cpuss1-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu0-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 5>; + + cooling-maps { + map0 { + trip = <&cpu0_alert1>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + cpu0_alert0: trip-point0 { + temperature = <75000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu0_alert1: trip-point1 { + temperature = <85000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpu0_crit: cpu-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu1-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 6>; + + cooling-maps { + map0 { + trip = <&cpu1_alert1>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + cpu1_alert0: trip-point0 { + temperature = <75000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpu1_alert1: trip-point1 { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu1_crit: cpu-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu2-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 7>; + + cooling-maps { + map0 { + trip = <&cpu2_alert1>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + cpu2_alert0: trip-point0 { + temperature = <75000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpu2_alert1: trip-point1 { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu2_crit: cpu-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + cpu3-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 8>; + + cooling-maps { + map0 { + trip = <&cpu3_alert1>; + cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, + <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + cpu3_alert0: trip-point0 { + temperature = <75000>; + hysteresis = <2000>; + type = "hot"; + }; + + cpu3_alert1: trip-point1 { + temperature = <85000>; + hysteresis = <2000>; + type = "passive"; + }; + + cpu3_crit: cpu-crit { + temperature = <100000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + }; + + gpu-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 9>; + + cooling-maps { + map0 { + trip = <&gpu_alert>; + cooling-device = <&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; + }; + }; + + trips { + gpu_alert: trip-point0 { + temperature = <70000>; + hysteresis = <2000>; + type = "passive"; + }; + + gpu_crit: gpu-crit { + temperature = <90000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + }; + + mdm-core-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 1>; + + trips { + mdm_core_alert0: trip-point0 { + temperature = <85000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + + q6-thermal { + polling-delay-passive = <250>; + + thermal-sensors = <&tsens 2>; + + trips { + q6_alert0: trip-point0 { + temperature = <85000>; + hysteresis = <2000>; + type = "hot"; + }; + }; + }; + }; +};