diff mbox series

[v6,1/3] arm64: dts: qcom: x1e80100-vivobook-s15: Use the samsung,atna33xc20 panel driver

Message ID 20241204-asus_qcom_display-v6-1-91079cd8234e@hotmail.com (mailing list archive)
State New
Headers show
Series Asus vivobook s15 improvements | expand

Commit Message

Maud Spierings via B4 Relay Dec. 4, 2024, 12:26 p.m. UTC 
From: Maud Spierings <maud_spierings@hotmail.com>

The Asus vivobook s15 uses the ATNA56AC03 panel.
This panel is controlled by the atna33xc20 driver instead of the generic
edp-panel driver

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Maud Spierings <maud_spierings@hotmail.com>
---
 .../boot/dts/qcom/x1e80100-asus-vivobook-s15.dts      | 19 ++++++++++++++++++-
 1 file changed, 18 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts b/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts
index f25991b887de3fca0092c5f81c881c5d8bd71aac..d909167dc7119fba56e0240f6f24fd1a803fa94c 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-asus-vivobook-s15.dts
@@ -8,6 +8,7 @@ 
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 
 #include "x1e80100.dtsi"
 #include "x1e80100-pmics.dtsi"
@@ -407,9 +408,13 @@  &mdss_dp3 {
 
 	aux-bus {
 		panel {
-			compatible = "edp-panel";
+			compatible = "samsung,atna56ac03", "samsung,atna33xc20";
+			enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
 			power-supply = <&vreg_edp_3p3>;
 
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
 			port {
 				edp_panel_in: endpoint {
 					remote-endpoint = <&mdss_dp3_out>;
@@ -475,6 +480,18 @@  &pcie6a_phy {
 	status = "okay";
 };
 
+&pmc8380_3_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>;
+		bias-pull-down;
+		input-disable;
+		output-enable;
+	};
+};
+
 &qupv3_0 {
 	status = "okay";
 };