diff mbox series

[v1,2/7] spi: dt-bindings: Document DT properties for QUP firmware loading

Message ID 20241204150326.1470749-3-quic_vdadhani@quicinc.com (mailing list archive)
State Not Applicable
Headers show
Series Add support to load QUP SE firmware from | expand

Commit Message

Viken Dadhaniya Dec. 4, 2024, 3:03 p.m. UTC 
Document the 'qcom,load-firmware' and 'qcom,xfer-mode' properties to
support SE(Serial Engine) firmware loading from the protocol driver and
to select the data transfer mode, either GPI DMA (Generic Packet Interface)
or non-GPI mode (PIO/CPU DMA).

SPI controller can operate in one of two modes based on the
'qcom,xfer-mode' property, and the firmware is loaded accordingly.

Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
---
 .../devicetree/bindings/spi/qcom,spi-geni-qcom.yaml   | 11 +++++++++++
 1 file changed, 11 insertions(+)

Comments

Krzysztof Kozlowski Dec. 4, 2024, 3:07 p.m. UTC | #1 
On 04/12/2024 16:03, Viken Dadhaniya wrote:
> Document the 'qcom,load-firmware' and 'qcom,xfer-mode' properties to
> support SE(Serial Engine) firmware loading from the protocol driver and
> to select the data transfer mode, either GPI DMA (Generic Packet Interface)
> or non-GPI mode (PIO/CPU DMA).
> 
> SPI controller can operate in one of two modes based on the
> 'qcom,xfer-mode' property, and the firmware is loaded accordingly.
> 
> Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
> Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@quicinc.com>
> Signed-off-by: Viken Dadhaniya <quic_vdadhani@quicinc.com>
> ---

My comments from I2C patch apply here, but let's keep discussion there.
Responding here just for formality.

Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml
index 2e20ca313ec1..7038981f54ff 100644
--- a/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml
+++ b/Documentation/devicetree/bindings/spi/qcom,spi-geni-qcom.yaml
@@ -66,6 +66,15 @@  properties:
   reg:
     maxItems: 1
 
+  qcom,load-firmware:
+    type: boolean
+    description: Optional property to load SE (serial engine) Firmware from protocol driver.
+
+  qcom,xfer-mode:
+    description: Value 1,2 and 3 represents FIFO, CPU DMA and GSI DMA mode respectively.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 3]
+
 required:
   - compatible
   - clocks
@@ -97,6 +106,8 @@  examples:
         interconnects = <&qup_virt MASTER_QUP_CORE_0 0 &qup_virt SLAVE_QUP_CORE_0 0>,
                         <&gem_noc MASTER_APPSS_PROC 0 &config_noc SLAVE_QUP_0 0>;
         interconnect-names = "qup-core", "qup-config";
+        qcom,load-firmware;
+        qcom,xfer-mode = <1>;
     };
 
   - |