diff --git a/drivers/net/ethernet/qualcomm/ppe/Makefile b/drivers/net/ethernet/qualcomm/ppe/Makefile
index 63d50d3b4f2e..410a7bb54cfe 100644
--- a/drivers/net/ethernet/qualcomm/ppe/Makefile
+++ b/drivers/net/ethernet/qualcomm/ppe/Makefile
@@ -4,4 +4,4 @@
 #
 
 obj-$(CONFIG_QCOM_PPE) += qcom-ppe.o
-qcom-ppe-objs := ppe.o
+qcom-ppe-objs := ppe.o ppe_config.o
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe.c b/drivers/net/ethernet/qualcomm/ppe/ppe.c
index 40da7d240594..253de6a15466 100644
--- a/drivers/net/ethernet/qualcomm/ppe/ppe.c
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe.c
@@ -15,6 +15,7 @@
 #include <linux/reset.h>
 
 #include "ppe.h"
+#include "ppe_config.h"
 
 #define PPE_PORT_MAX		8
 #define PPE_CLK_RATE		353000000
@@ -194,6 +195,10 @@ static int qcom_ppe_probe(struct platform_device *pdev)
 	if (ret)
 		return dev_err_probe(dev, ret, "PPE clock config failed\n");
 
+	ret = ppe_hw_config(ppe_dev);
+	if (ret)
+		return dev_err_probe(dev, ret, "PPE HW config failed\n");
+
 	platform_set_drvdata(pdev, ppe_dev);
 
 	return 0;
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe_config.c b/drivers/net/ethernet/qualcomm/ppe/ppe_config.c
new file mode 100644
index 000000000000..18e9544a4e37
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe_config.c
@@ -0,0 +1,195 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/* PPE HW initialization configs such as BM(buffer management),
+ * QM(queue management) and scheduler configs.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+#include "ppe.h"
+#include "ppe_config.h"
+#include "ppe_regs.h"
+
+/**
+ * struct ppe_bm_port_config - PPE BM port configuration.
+ * @port_id_start: The fist BM port ID to configure.
+ * @port_id_end: The last BM port ID to configure.
+ * @pre_alloc: BM port dedicated buffer number.
+ * @in_fly_buf: Buffer number for receiving the packet after pause frame sent.
+ * @ceil: Ceil to generate the back pressure.
+ * @weight: Weight value.
+ * @resume_offset: Resume offset from the threshold value.
+ * @resume_ceil: Ceil to resume from the back pressure state.
+ * @dynamic: Dynamic threshold used or not.
+ *
+ * The is for configuring the threshold that impacts the port
+ * flow control.
+ */
+struct ppe_bm_port_config {
+	unsigned int port_id_start;
+	unsigned int port_id_end;
+	unsigned int pre_alloc;
+	unsigned int in_fly_buf;
+	unsigned int ceil;
+	unsigned int weight;
+	unsigned int resume_offset;
+	unsigned int resume_ceil;
+	bool dynamic;
+};
+
+/* Assign the share buffer number 1550 to group 0 by default. */
+static const int ipq9574_ppe_bm_group_config = 1550;
+
+/* The buffer configurations per PPE port. There are 15 BM ports and
+ * 4 BM groups supported by PPE. BM port (0-7) is for EDMA port 0,
+ * BM port (8-13) is for PPE physical port 1-6 and BM port 14 is for
+ * EIP port.
+ */
+static const struct ppe_bm_port_config ipq9574_ppe_bm_port_config[] = {
+	{
+		/* Buffer configuration for the BM port ID 0 of EDMA. */
+		.port_id_start	= 0,
+		.port_id_end	= 0,
+		.pre_alloc	= 0,
+		.in_fly_buf	= 100,
+		.ceil		= 1146,
+		.weight		= 7,
+		.resume_offset	= 8,
+		.resume_ceil	= 0,
+		.dynamic	= true,
+	},
+	{
+		/* Buffer configuration for the BM port ID 1-7 of EDMA. */
+		.port_id_start	= 1,
+		.port_id_end	= 7,
+		.pre_alloc	= 0,
+		.in_fly_buf	= 100,
+		.ceil		= 250,
+		.weight		= 4,
+		.resume_offset	= 36,
+		.resume_ceil	= 0,
+		.dynamic	= true,
+	},
+	{
+		/* Buffer configuration for the BM port ID 8-13 of PPE ports. */
+		.port_id_start	= 8,
+		.port_id_end	= 13,
+		.pre_alloc	= 0,
+		.in_fly_buf	= 128,
+		.ceil		= 250,
+		.weight		= 4,
+		.resume_offset	= 36,
+		.resume_ceil	= 0,
+		.dynamic	= true,
+	},
+	{
+		/* Buffer configuration for the BM port ID 14 of EIP. */
+		.port_id_start	= 14,
+		.port_id_end	= 14,
+		.pre_alloc	= 0,
+		.in_fly_buf	= 40,
+		.ceil		= 250,
+		.weight		= 4,
+		.resume_offset	= 36,
+		.resume_ceil	= 0,
+		.dynamic	= true,
+	},
+};
+
+static int ppe_config_bm_threshold(struct ppe_device *ppe_dev, int bm_port_id,
+				   const struct ppe_bm_port_config port_cfg)
+{
+	u32 reg, val, bm_fc_val[2];
+	int ret;
+
+	reg = PPE_BM_PORT_FC_CFG_TBL_ADDR + PPE_BM_PORT_FC_CFG_TBL_INC * bm_port_id;
+	ret = regmap_bulk_read(ppe_dev->regmap, reg,
+			       bm_fc_val, ARRAY_SIZE(bm_fc_val));
+	if (ret)
+		return ret;
+
+	/* Configure BM flow control related threshold. */
+	PPE_BM_PORT_FC_SET_WEIGHT(bm_fc_val, port_cfg.weight);
+	PPE_BM_PORT_FC_SET_RESUME_OFFSET(bm_fc_val, port_cfg.resume_offset);
+	PPE_BM_PORT_FC_SET_RESUME_THRESHOLD(bm_fc_val, port_cfg.resume_ceil);
+	PPE_BM_PORT_FC_SET_DYNAMIC(bm_fc_val, port_cfg.dynamic);
+	PPE_BM_PORT_FC_SET_REACT_LIMIT(bm_fc_val, port_cfg.in_fly_buf);
+	PPE_BM_PORT_FC_SET_PRE_ALLOC(bm_fc_val, port_cfg.pre_alloc);
+
+	/* Configure low/high bits of the ceiling for the BM port. */
+	val = FIELD_GET(GENMASK(2, 0), port_cfg.ceil);
+	PPE_BM_PORT_FC_SET_CEILING_LOW(bm_fc_val, val);
+	val = FIELD_GET(GENMASK(10, 3), port_cfg.ceil);
+	PPE_BM_PORT_FC_SET_CEILING_HIGH(bm_fc_val, val);
+
+	ret = regmap_bulk_write(ppe_dev->regmap, reg,
+				bm_fc_val, ARRAY_SIZE(bm_fc_val));
+	if (ret)
+		return ret;
+
+	/* Assign the default group ID 0 to the BM port. */
+	val = FIELD_PREP(PPE_BM_PORT_GROUP_ID_SHARED_GROUP_ID, 0);
+	reg = PPE_BM_PORT_GROUP_ID_ADDR + PPE_BM_PORT_GROUP_ID_INC * bm_port_id;
+	ret = regmap_update_bits(ppe_dev->regmap, reg,
+				 PPE_BM_PORT_GROUP_ID_SHARED_GROUP_ID,
+				 val);
+	if (ret)
+		return ret;
+
+	/* Enable BM port flow control. */
+	reg = PPE_BM_PORT_FC_MODE_ADDR + PPE_BM_PORT_FC_MODE_INC * bm_port_id;
+
+	return regmap_set_bits(ppe_dev->regmap, reg, PPE_BM_PORT_FC_MODE_EN);
+}
+
+/* Configure the buffer threshold for the port flow control function. */
+static int ppe_config_bm(struct ppe_device *ppe_dev)
+{
+	const struct ppe_bm_port_config *port_cfg;
+	unsigned int i, bm_port_id, port_cfg_cnt;
+	u32 reg, val;
+	int ret;
+
+	/* Configure the allocated buffer number only for group 0.
+	 * The buffer number of group 1-3 is already cleared to 0
+	 * after PPE reset during the probe of PPE driver.
+	 */
+	reg = PPE_BM_SHARED_GROUP_CFG_ADDR;
+	val = FIELD_PREP(PPE_BM_SHARED_GROUP_CFG_SHARED_LIMIT,
+			 ipq9574_ppe_bm_group_config);
+	ret = regmap_update_bits(ppe_dev->regmap, reg,
+				 PPE_BM_SHARED_GROUP_CFG_SHARED_LIMIT,
+				 val);
+	if (ret)
+		goto bm_config_fail;
+
+	/* Configure buffer thresholds for the BM ports. */
+	port_cfg = ipq9574_ppe_bm_port_config;
+	port_cfg_cnt = ARRAY_SIZE(ipq9574_ppe_bm_port_config);
+	for (i = 0; i < port_cfg_cnt; i++) {
+		for (bm_port_id = port_cfg[i].port_id_start;
+		     bm_port_id <= port_cfg[i].port_id_end; bm_port_id++) {
+			ret = ppe_config_bm_threshold(ppe_dev, bm_port_id,
+						      port_cfg[i]);
+			if (ret)
+				goto bm_config_fail;
+		}
+	}
+
+	return 0;
+
+bm_config_fail:
+	dev_err(ppe_dev->dev, "PPE BM config error %d\n", ret);
+	return ret;
+}
+
+int ppe_hw_config(struct ppe_device *ppe_dev)
+{
+	return ppe_config_bm(ppe_dev);
+}
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe_config.h b/drivers/net/ethernet/qualcomm/ppe/ppe_config.h
new file mode 100644
index 000000000000..7b2f6a71cd4c
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe_config.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-only
+ *
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#ifndef __PPE_CONFIG_H__
+#define __PPE_CONFIG_H__
+
+#include "ppe.h"
+
+int ppe_hw_config(struct ppe_device *ppe_dev);
+#endif
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe_regs.h b/drivers/net/ethernet/qualcomm/ppe/ppe_regs.h
new file mode 100644
index 000000000000..b00f77ec45fe
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe_regs.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only
+ *
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/* PPE hardware register and table declarations. */
+#ifndef __PPE_REGS_H__
+#define __PPE_REGS_H__
+
+#include <linux/bitfield.h>
+
+/* There are 15 BM ports and 4 BM groups supported by PPE.
+ * BM port (0-7) is for EDMA port 0, BM port (8-13) is for
+ * PPE physical port 1-6 and BM port 14 is for EIP port.
+ */
+#define PPE_BM_PORT_FC_MODE_ADDR		0x600100
+#define PPE_BM_PORT_FC_MODE_ENTRIES		15
+#define PPE_BM_PORT_FC_MODE_INC			0x4
+#define PPE_BM_PORT_FC_MODE_EN			BIT(0)
+
+#define PPE_BM_PORT_GROUP_ID_ADDR		0x600180
+#define PPE_BM_PORT_GROUP_ID_ENTRIES		15
+#define PPE_BM_PORT_GROUP_ID_INC		0x4
+#define PPE_BM_PORT_GROUP_ID_SHARED_GROUP_ID	GENMASK(1, 0)
+
+#define PPE_BM_SHARED_GROUP_CFG_ADDR		0x600290
+#define PPE_BM_SHARED_GROUP_CFG_ENTRIES		4
+#define PPE_BM_SHARED_GROUP_CFG_INC		0x4
+#define PPE_BM_SHARED_GROUP_CFG_SHARED_LIMIT	GENMASK(10, 0)
+
+#define PPE_BM_PORT_FC_CFG_TBL_ADDR		0x601000
+#define PPE_BM_PORT_FC_CFG_TBL_ENTRIES		15
+#define PPE_BM_PORT_FC_CFG_TBL_INC		0x10
+#define PPE_BM_PORT_FC_W0_REACT_LIMIT		GENMASK(8, 0)
+#define PPE_BM_PORT_FC_W0_RESUME_THRESHOLD	GENMASK(17, 9)
+#define PPE_BM_PORT_FC_W0_RESUME_OFFSET		GENMASK(28, 18)
+#define PPE_BM_PORT_FC_W0_CEILING_LOW		GENMASK(31, 29)
+#define PPE_BM_PORT_FC_W1_CEILING_HIGH		GENMASK(7, 0)
+#define PPE_BM_PORT_FC_W1_WEIGHT		GENMASK(10, 8)
+#define PPE_BM_PORT_FC_W1_DYNAMIC		BIT(11)
+#define PPE_BM_PORT_FC_W1_PRE_ALLOC		GENMASK(22, 12)
+
+#define PPE_BM_PORT_FC_SET_REACT_LIMIT(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_REACT_LIMIT)
+#define PPE_BM_PORT_FC_SET_RESUME_THRESHOLD(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_RESUME_THRESHOLD)
+#define PPE_BM_PORT_FC_SET_RESUME_OFFSET(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_RESUME_OFFSET)
+#define PPE_BM_PORT_FC_SET_CEILING_LOW(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_CEILING_LOW)
+#define PPE_BM_PORT_FC_SET_CEILING_HIGH(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_CEILING_HIGH)
+#define PPE_BM_PORT_FC_SET_WEIGHT(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_WEIGHT)
+#define PPE_BM_PORT_FC_SET_DYNAMIC(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_DYNAMIC)
+#define PPE_BM_PORT_FC_SET_PRE_ALLOC(tbl_cfg, value)	\
+	u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_PRE_ALLOC)
+#endif
