diff mbox series

[3/3] ARM: dts: qcom: Add MikroTik RB3011

Message ID 75390e66c9e6e36ddd42dc7f54cac28dfd7a24b9.1589824955.git.noodles@earth.li (mailing list archive)
State Accepted
Commit 5de14398b6611af89a253f3fa13c20a92d53a513
Headers show
Series Add initial support for MikroTik RB3011 | expand

Commit Message

Jonathan McDowell May 18, 2020, 6:10 p.m. UTC 
This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a
1U rackmount router based on the IPQ8064, supporting the serial UART,
dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED
device.

Signed-off-by: Jonathan McDowell <noodles@earth.li>
---
 arch/arm/boot/dts/Makefile                |   1 +
 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 308 ++++++++++++++++++++++
 2 files changed, 309 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts

Comments

Bjorn Andersson May 29, 2020, 3:20 a.m. UTC | #1 
On Mon 18 May 11:10 PDT 2020, Jonathan McDowell wrote:

> This patch adds a DTS file for the MikroTik RouterBoard 3011, which is a
> 1U rackmount router based on the IPQ8064, supporting the serial UART,
> dual QCA8337 Gigabit ethernet switches, boot loader NOR and user LED
> device.
> 
> Signed-off-by: Jonathan McDowell <noodles@earth.li>

Patch 2 and 3 picked up for 5.9

Thanks,
Bjorn

> ---
>  arch/arm/boot/dts/Makefile                |   1 +
>  arch/arm/boot/dts/qcom-ipq8064-rb3011.dts | 308 ++++++++++++++++++++++
>  2 files changed, 309 insertions(+)
>  create mode 100644 arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index e8dd99201397..e697a4bd7426 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -884,6 +884,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
>  	qcom-ipq4019-ap.dk07.1-c1.dtb \
>  	qcom-ipq4019-ap.dk07.1-c2.dtb \
>  	qcom-ipq8064-ap148.dtb \
> +	qcom-ipq8064-rb3011.dtb \
>  	qcom-msm8660-surf.dtb \
>  	qcom-msm8960-cdp.dtb \
>  	qcom-msm8974-fairphone-fp2.dtb \
> diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> new file mode 100644
> index 000000000000..282b89ce3d45
> --- /dev/null
> +++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> @@ -0,0 +1,308 @@
> +// SPDX-License-Identifier: GPL-2.0
> +#include "qcom-ipq8064.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> +	model = "MikroTik RB3011UiAS-RM";
> +	compatible = "mikrotik,rb3011";
> +
> +	aliases {
> +		serial0 = &gsbi7_serial;
> +		ethernet0 = &gmac0;
> +		ethernet1 = &gmac3;
> +		mdio-gpio0 = &mdio0;
> +		mdio-gpio1 = &mdio1;
> +	};
> +
> +	chosen {
> +		bootargs = "loglevel=8 console=ttyMSM0,115200";
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory@0 {
> +		reg = <0x42000000 0x3e000000>;
> +		device_type = "memory";
> +	};
> +
> +	mdio0: mdio@0 {
> +		status = "okay";
> +		compatible = "virtual,mdio-gpio";
> +		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
> +			<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pinctrl-0 = <&mdio0_pins>;
> +		pinctrl-names = "default";
> +
> +		switch0: switch@10 {
> +			compatible = "qca,qca8337";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			dsa,member = <0 0>;
> +
> +			pinctrl-0 = <&sw0_reset_pin>;
> +			pinctrl-names = "default";
> +
> +			reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
> +			reg = <0x10>;
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				switch0cpu: port@0 {
> +					reg = <0>;
> +					label = "cpu";
> +					ethernet = <&gmac0>;
> +					phy-mode = "rgmii-id";
> +					fixed-link {
> +						speed = <1000>;
> +						full-duplex;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +					label = "sw1";
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +					label = "sw2";
> +				};
> +
> +				port@3 {
> +					reg = <3>;
> +					label = "sw3";
> +				};
> +
> +				port@4 {
> +					reg = <4>;
> +					label = "sw4";
> +				};
> +
> +				port@5 {
> +					reg = <5>;
> +					label = "sw5";
> +				};
> +			};
> +		};
> +	};
> +
> +	mdio1: mdio@1 {
> +		status = "okay";
> +		compatible = "virtual,mdio-gpio";
> +		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
> +			<&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		pinctrl-0 = <&mdio1_pins>;
> +		pinctrl-names = "default";
> +
> +		switch1: switch@14 {
> +			compatible = "qca,qca8337";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			dsa,member = <1 0>;
> +
> +			pinctrl-0 = <&sw1_reset_pin>;
> +			pinctrl-names = "default";
> +
> +			reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
> +			reg = <0x10>;
> +
> +			ports {
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				switch1cpu: port@0 {
> +					reg = <0>;
> +					label = "cpu";
> +					ethernet = <&gmac3>;
> +					phy-mode = "sgmii";
> +					fixed-link {
> +						speed = <1000>;
> +						full-duplex;
> +					};
> +				};
> +
> +				port@1 {
> +					reg = <1>;
> +					label = "sw6";
> +				};
> +
> +				port@2 {
> +					reg = <2>;
> +					label = "sw7";
> +				};
> +
> +				port@3 {
> +					reg = <3>;
> +					label = "sw8";
> +				};
> +
> +				port@4 {
> +					reg = <4>;
> +					label = "sw9";
> +				};
> +
> +				port@5 {
> +					reg = <5>;
> +					label = "sw10";
> +				};
> +			};
> +		};
> +	};
> +
> +	soc {
> +		gsbi5: gsbi@1a200000 {
> +			qcom,mode = <GSBI_PROT_SPI>;
> +			status = "okay";
> +
> +			spi4: spi@1a280000 {
> +				status = "okay";
> +				spi-max-frequency = <50000000>;
> +
> +				pinctrl-0 = <&spi_pins>;
> +				pinctrl-names = "default";
> +
> +				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
> +
> +				norflash: s25fl016k@0 {
> +					compatible = "jedec,spi-nor";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +					spi-max-frequency = <50000000>;
> +					reg = <0>;
> +
> +					partition@0 {
> +						label = "RouterBoot";
> +						reg = <0x0 0x40000>;
> +					};
> +				};
> +			};
> +		};
> +
> +		gpio_keys {
> +			compatible = "gpio-keys";
> +			pinctrl-0 = <&buttons_pins>;
> +			pinctrl-names = "default";
> +
> +			button@1 {
> +				label = "reset";
> +				linux,code = <KEY_RESTART>;
> +				gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
> +				linux,input-type = <1>;
> +				debounce-interval = <60>;
> +			};
> +		};
> +
> +		leds {
> +			compatible = "gpio-leds";
> +			pinctrl-0 = <&leds_pins>;
> +			pinctrl-names = "default";
> +
> +			led@7 {
> +				label = "rb3011:green:user";
> +				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
> +				default-state = "off";
> +			};
> +		};
> +
> +	};
> +};
> +
> +&gmac0 {
> +	status = "okay";
> +
> +	phy-mode = "rgmii";
> +	qcom,id = <0>;
> +	phy-handle = <&switch0cpu>;
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> +
> +&gmac3 {
> +	status = "okay";
> +
> +	phy-mode = "sgmii";
> +	qcom,id = <3>;
> +	phy-handle = <&switch1cpu>;
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> +
> +&gsbi7 {
> +	status = "okay";
> +	qcom,mode = <GSBI_PROT_I2C_UART>;
> +};
> +
> +&gsbi7_serial {
> +	status = "okay";
> +};
> +
> +&qcom_pinmux {
> +	buttons_pins: buttons_pins {
> +		mux {
> +			pins = "gpio66";
> +			drive-strength = <16>;
> +			bias-disable;
> +		};
> +	};
> +
> +	leds_pins: leds_pins {
> +		mux {
> +			pins = "gpio33";
> +			drive-strength = <16>;
> +			bias-disable;
> +		};
> +	};
> +
> +	mdio0_pins: mdio0_pins {
> +		mux {
> +			pins = "gpio0", "gpio1";
> +			function = "gpio";
> +			drive-strength = <8>;
> +			bias-disable;
> +		};
> +	};
> +
> +	mdio1_pins: mdio1_pins {
> +		mux {
> +			pins = "gpio10", "gpio11";
> +			function = "gpio";
> +			drive-strength = <8>;
> +			bias-disable;
> +		};
> +	};
> +
> +	sw0_reset_pin: sw0_reset_pin {
> +		mux {
> +			pins = "gpio16";
> +			drive-strength = <16>;
> +			function = "gpio";
> +			bias-disable;
> +			input-disable;
> +		};
> +	};
> +
> +	sw1_reset_pin: sw1_reset_pin {
> +		mux {
> +			pins = "gpio17";
> +			drive-strength = <16>;
> +			function = "gpio";
> +			bias-disable;
> +			input-disable;
> +		};
> +	};
> +};
> -- 
> 2.20.1
>
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index e8dd99201397..e697a4bd7426 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -884,6 +884,7 @@  dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-ipq4019-ap.dk07.1-c1.dtb \
 	qcom-ipq4019-ap.dk07.1-c2.dtb \
 	qcom-ipq8064-ap148.dtb \
+	qcom-ipq8064-rb3011.dtb \
 	qcom-msm8660-surf.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8974-fairphone-fp2.dtb \
diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
new file mode 100644
index 000000000000..282b89ce3d45
--- /dev/null
+++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
@@ -0,0 +1,308 @@ 
+// SPDX-License-Identifier: GPL-2.0
+#include "qcom-ipq8064.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+	model = "MikroTik RB3011UiAS-RM";
+	compatible = "mikrotik,rb3011";
+
+	aliases {
+		serial0 = &gsbi7_serial;
+		ethernet0 = &gmac0;
+		ethernet1 = &gmac3;
+		mdio-gpio0 = &mdio0;
+		mdio-gpio1 = &mdio1;
+	};
+
+	chosen {
+		bootargs = "loglevel=8 console=ttyMSM0,115200";
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		reg = <0x42000000 0x3e000000>;
+		device_type = "memory";
+	};
+
+	mdio0: mdio@0 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio0_pins>;
+		pinctrl-names = "default";
+
+		switch0: switch@10 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsa,member = <0 0>;
+
+			pinctrl-0 = <&sw0_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 16 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch0cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac0>;
+					phy-mode = "rgmii-id";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw1";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw2";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw3";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw4";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw5";
+				};
+			};
+		};
+	};
+
+	mdio1: mdio@1 {
+		status = "okay";
+		compatible = "virtual,mdio-gpio";
+		gpios = <&qcom_pinmux 11 GPIO_ACTIVE_HIGH>,
+			<&qcom_pinmux 10 GPIO_ACTIVE_HIGH>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		pinctrl-0 = <&mdio1_pins>;
+		pinctrl-names = "default";
+
+		switch1: switch@14 {
+			compatible = "qca,qca8337";
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dsa,member = <1 0>;
+
+			pinctrl-0 = <&sw1_reset_pin>;
+			pinctrl-names = "default";
+
+			reset-gpios = <&qcom_pinmux 17 GPIO_ACTIVE_LOW>;
+			reg = <0x10>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				switch1cpu: port@0 {
+					reg = <0>;
+					label = "cpu";
+					ethernet = <&gmac3>;
+					phy-mode = "sgmii";
+					fixed-link {
+						speed = <1000>;
+						full-duplex;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					label = "sw6";
+				};
+
+				port@2 {
+					reg = <2>;
+					label = "sw7";
+				};
+
+				port@3 {
+					reg = <3>;
+					label = "sw8";
+				};
+
+				port@4 {
+					reg = <4>;
+					label = "sw9";
+				};
+
+				port@5 {
+					reg = <5>;
+					label = "sw10";
+				};
+			};
+		};
+	};
+
+	soc {
+		gsbi5: gsbi@1a200000 {
+			qcom,mode = <GSBI_PROT_SPI>;
+			status = "okay";
+
+			spi4: spi@1a280000 {
+				status = "okay";
+				spi-max-frequency = <50000000>;
+
+				pinctrl-0 = <&spi_pins>;
+				pinctrl-names = "default";
+
+				cs-gpios = <&qcom_pinmux 20 GPIO_ACTIVE_HIGH>;
+
+				norflash: s25fl016k@0 {
+					compatible = "jedec,spi-nor";
+					#address-cells = <1>;
+					#size-cells = <1>;
+					spi-max-frequency = <50000000>;
+					reg = <0>;
+
+					partition@0 {
+						label = "RouterBoot";
+						reg = <0x0 0x40000>;
+					};
+				};
+			};
+		};
+
+		gpio_keys {
+			compatible = "gpio-keys";
+			pinctrl-0 = <&buttons_pins>;
+			pinctrl-names = "default";
+
+			button@1 {
+				label = "reset";
+				linux,code = <KEY_RESTART>;
+				gpios = <&qcom_pinmux 66 GPIO_ACTIVE_LOW>;
+				linux,input-type = <1>;
+				debounce-interval = <60>;
+			};
+		};
+
+		leds {
+			compatible = "gpio-leds";
+			pinctrl-0 = <&leds_pins>;
+			pinctrl-names = "default";
+
+			led@7 {
+				label = "rb3011:green:user";
+				gpios = <&qcom_pinmux 33 GPIO_ACTIVE_HIGH>;
+				default-state = "off";
+			};
+		};
+
+	};
+};
+
+&gmac0 {
+	status = "okay";
+
+	phy-mode = "rgmii";
+	qcom,id = <0>;
+	phy-handle = <&switch0cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gmac3 {
+	status = "okay";
+
+	phy-mode = "sgmii";
+	qcom,id = <3>;
+	phy-handle = <&switch1cpu>;
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
+
+&gsbi7 {
+	status = "okay";
+	qcom,mode = <GSBI_PROT_I2C_UART>;
+};
+
+&gsbi7_serial {
+	status = "okay";
+};
+
+&qcom_pinmux {
+	buttons_pins: buttons_pins {
+		mux {
+			pins = "gpio66";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	leds_pins: leds_pins {
+		mux {
+			pins = "gpio33";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	mdio0_pins: mdio0_pins {
+		mux {
+			pins = "gpio0", "gpio1";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	mdio1_pins: mdio1_pins {
+		mux {
+			pins = "gpio10", "gpio11";
+			function = "gpio";
+			drive-strength = <8>;
+			bias-disable;
+		};
+	};
+
+	sw0_reset_pin: sw0_reset_pin {
+		mux {
+			pins = "gpio16";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+
+	sw1_reset_pin: sw1_reset_pin {
+		mux {
+			pins = "gpio17";
+			drive-strength = <16>;
+			function = "gpio";
+			bias-disable;
+			input-disable;
+		};
+	};
+};