new file mode 100644
@@ -0,0 +1,114 @@
+What: /sys/bus/platform/devices/.../trigger
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This is the sysfs interface for manual software
+ triggers.The user can simply enter a 1 against
+ the sysfs file and enable a manual trigger.
+ Example:
+ echo 1 > /sys/bus/platform/devices/.../trigger
+
+What: /sys/bus/platform/devices/.../enable
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This sysfs interface is used for enabling the
+ the dcc hardware.Without this being set to 1,
+ the dcc hardware ceases to function.
+ Example:
+ echo 0 > /sys/bus/platform/devices/.../enable
+ (disable interface)
+ echo 1 > /sys/bus/platform/devices/.../enable
+ (enable interface)
+
+What: /sys/bus/platform/devices/.../config
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This is the most commonly used sysfs interface
+ file and this basically stores the addresses of
+ the registers which needs to be read in case of
+ a hardware crash or manual software triggers.
+ Example:
+ echo 0x80000010 10 > /sys/bus/platform/devices/../config
+ This specifies that 10 words starting from address
+ 0x80000010 is to be read.In case there are no words to be
+ specified we can simply enter the address.
+
+What: /sys/bus/platform/devices/.../config_write
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This file allows user to write a value to the register
+ address given as argument.The values are entered in the
+ form of <register_address> <value>.The reason for this
+ feature of dcc is that for accessing certain registers
+ it is necessary to set some bits of soe other register.
+ That is achievable by giving DCC this privelege.
+ Example:
+ echo 0x80000000 0xFF > /sys/bus/platform/devices/.../config_write
+
+What: /sys/bus/platform/devices/.../config_reset
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This file is used to reset the configuration of
+ a dcc driver to the default configuration.
+ Example:
+ echo 1 > /sys/bus/platform/devices/.../config_reset
+
+What: /sys/bus/platform/devices/.../loop
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This file is used to enter the loop count as dcc
+ driver gives the option to loop multiple times on
+ the same register and store the values for each
+ loop.This is done to capture the changing values
+ of a register with time which comes handy for
+ debugging purposes.
+ Example:
+ echo 10 > /sys/bus/platform/devices/10a2000.dcc/loop
+ (Setting the loop count to 10)
+ echo 0x80000010 10 > /sys/bus/platform/devices/.../config
+ (Read 10 words starting from address 0x80000010O)
+ echo 1 > /sys/bus/platform/devices/.../loop
+ (Terminate the loop by writing a count of 1 to the loop sysfs node)
+
+What: /sys/bus/platform/devices/.../rd_mod_wr
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This file is used to read the value of the register
+ and then write the value given as an argument to the
+ register address in config.The address argument should
+ be given of the form <mask> <value>.For debugging
+ purposes sometimes we need to first read from a register
+ and then set some values to the register.
+ Example:
+ echo 0x80000000 > /sys/bus/platform/devices/.../config
+ (Set the address in config file)
+ echo 0xF 0xA > /sys/bus/platform/devices/.../rd_mod_wr
+ (Provide the mask and the value to write)
+
+What: /sys/bus/platform/devices/.../ready
+Date: March 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This file is used to check the status of the dcc
+ hardware if it's ready to take the inputs.
+ Example:
+ cat /sys/bus/platform/devices/.../ready
+
+What: /sys/bus/platform/devices/.../curr_list
+Date: February 2021
+Contact: Souradeep Chowdhury <schowdhu@codeaurora.org>
+Description:
+ This attribute is used to enter the linklist to be
+ used while appending addresses.The range of values
+ for this can be from 0 to 3.This feature is given in
+ order to use certain linkedlist for certain debugging
+ purposes.
+ Example:
+ echo 0 > /sys/bus/platform/devices/10a2000.dcc/curr_list
+
The DCC is a DMA engine designed to store register values either in case of a system crash or in case of software triggers manually done by the user.Using DCC hardware and the sysfs interface of the driver the user can exploit various functionalities of DCC.The user can specify the register addresses,the values of which is stored by DCC in it's dedicated SRAM.The register addresses can be used either to read from, write to,first read and store value and then write or to loop.All these options can be exploited using the sysfs interface given to the user. Following are the sysfs interfaces exposed in DCC driver which are documented 1)trigger 2)config 3)config_write 4)config_reset 5)enable 6)rd_mod_wr 7)loop Signed-off-by: Souradeep Chowdhury <schowdhu@codeaurora.org> --- Documentation/ABI/testing/sysfs-driver-dcc | 114 +++++++++++++++++++++++++++++ 1 file changed, 114 insertions(+) create mode 100644 Documentation/ABI/testing/sysfs-driver-dcc