diff mbox series

[v4,3/3] arm64: dts: qcom: msm8916-thwc: Add initial device trees

Message ID tencent_AB776DFEB1B993E8B3F0BD5A4BF420600407@qq.com (mailing list archive)
State Queued
Headers show
Series [v4,1/3] dt-bindings: vendor-prefixes: add thwc | expand

Commit Message

Yang Xiwen Jan. 14, 2023, 6:38 a.m. UTC
This commit adds support for the ufi-001C and uf896 WiFi/LTE dongle made by
Tong Heng Wei Chuang based on MSM8916.
uf896 is another variant for the usb stick. The board design
differs by using different gpios for the keys and leds.

Note: The original firmware does not support 64-bit OS. It is necessary
to flash 64-bit TZ firmware to boot arm64.

Currently supported:
- All CPU cores
- Buttons
- LEDs
- Modem
- SDHC
- USB Device Mode
- UART

Co-developed-by: Jaime Breva <jbreva@nayarsystems.com>
Signed-off-by: Jaime Breva <jbreva@nayarsystems.com>
Co-developed-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   2 +
 .../boot/dts/qcom/msm8916-thwc-uf896.dts      |  39 +++
 .../boot/dts/qcom/msm8916-thwc-ufi001c.dts    |  39 +++
 arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi     | 250 ++++++++++++++++++
 4 files changed, 330 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
 create mode 100644 arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi

Comments

Konrad Dybcio Jan. 14, 2023, 8:54 p.m. UTC | #1
On 14.01.2023 07:38, Yang Xiwen wrote:
> This commit adds support for the ufi-001C and uf896 WiFi/LTE dongle made by
> Tong Heng Wei Chuang based on MSM8916.
> uf896 is another variant for the usb stick. The board design
> differs by using different gpios for the keys and leds.
> 
> Note: The original firmware does not support 64-bit OS. It is necessary
> to flash 64-bit TZ firmware to boot arm64.
> 
> Currently supported:
> - All CPU cores
> - Buttons
> - LEDs
> - Modem
> - SDHC
> - USB Device Mode
> - UART
> 
> Co-developed-by: Jaime Breva <jbreva@nayarsystems.com>
> Signed-off-by: Jaime Breva <jbreva@nayarsystems.com>
> Co-developed-by: Nikita Travkin <nikita@trvn.ru>
> Signed-off-by: Nikita Travkin <nikita@trvn.ru>
> Signed-off-by: Yang Xiwen <forbidden405@foxmail.com>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad
>  arch/arm64/boot/dts/qcom/Makefile             |   2 +
>  .../boot/dts/qcom/msm8916-thwc-uf896.dts      |  39 +++
>  .../boot/dts/qcom/msm8916-thwc-ufi001c.dts    |  39 +++
>  arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi     | 250 ++++++++++++++++++
>  4 files changed, 330 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
>  create mode 100644 arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index e442a81895d04..d83e02c84d42c 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -22,6 +22,8 @@ dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-e7.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-grandmax.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-j5.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-serranove.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-thwc-uf896.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-thwc-ufi001c.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-potter.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-daisy.dtb
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
> new file mode 100644
> index 0000000000000..c492db8561904
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
> @@ -0,0 +1,39 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/dts-v1/;
> +
> +#include "msm8916-ufi.dtsi"
> +
> +/ {
> +	model = "uf896 4G Modem Stick";
> +	compatible = "thwc,uf896", "qcom,msm8916";
> +};
> +
> +&button_restart {
> +	gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
> +};
> +
> +&led_r {
> +	gpios = <&msmgpio 82 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_g {
> +	gpios = <&msmgpio 83 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_b {
> +	gpios = <&msmgpio 81 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&button_default {
> +	pins = "gpio35";
> +	bias-pull-up;
> +};
> +
> +&gpio_leds_default {
> +	pins = "gpio81", "gpio82", "gpio83";
> +};
> +
> +&sim_ctrl_default {
> +	pins = "gpio1", "gpio2";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
> new file mode 100644
> index 0000000000000..700cf81cbf8c0
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
> @@ -0,0 +1,39 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +/dts-v1/;
> +
> +#include "msm8916-ufi.dtsi"
> +
> +/ {
> +	model = "ufi-001c/ufi-001b 4G Modem Stick";
> +	compatible = "thwc,ufi001c", "qcom,msm8916";
> +};
> +
> +&button_restart {
> +	gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_r {
> +	gpios = <&msmgpio 22 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_g {
> +	gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&led_b {
> +	gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>;
> +};
> +
> +&button_default {
> +	pins = "gpio37";
> +	bias-pull-down;
> +};
> +
> +&gpio_leds_default {
> +	pins = "gpio20", "gpio21", "gpio22";
> +};
> +
> +&sim_ctrl_default {
> +	pins = "gpio1", "gpio2";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
> new file mode 100644
> index 0000000000000..790a9696da9de
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
> @@ -0,0 +1,250 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +
> +#include "msm8916-pm8916.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +
> +/ {
> +	chassis-type = "embedded";
> +
> +	aliases {
> +		serial0 = &blsp1_uart2;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0";
> +	};
> +
> +	reserved-memory {
> +		mpss_mem: mpss@86800000 {
> +			reg = <0x0 0x86800000 0x0 0x5500000>;
> +			no-map;
> +		};
> +
> +		gps_mem: gps@8bd00000 {
> +			reg = <0x0 0x8bd00000 0x0 0x200000>;
> +			no-map;
> +		};
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		pinctrl-0 = <&button_default>;
> +		pinctrl-names = "default";
> +
> +		label = "GPIO Buttons";
> +
> +		/* GPIO is board-specific */
> +		button_restart: button-restart {
> +			label = "Restart";
> +			linux,code = <KEY_RESTART>;
> +		};
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		pinctrl-0 = <&gpio_leds_default>;
> +		pinctrl-names = "default";
> +
> +		/*
> +		 * GPIOs are board-specific.
> +		 * Functions and default-states defined here are fallbacks.
> +		 * Feel free to override them if your board is different.
> +		 */
> +		led_r: led-r {
> +			color = <LED_COLOR_ID_RED>;
> +			default-state = "on";
> +			function = LED_FUNCTION_POWER;
> +		};
> +
> +		led_g: led-g {
> +			color = <LED_COLOR_ID_GREEN>;
> +			default-state = "off";
> +			function = LED_FUNCTION_WLAN;
> +		};
> +
> +		led_b: led-b {
> +			color = <LED_COLOR_ID_BLUE>;
> +			default-state = "off";
> +			function = LED_FUNCTION_WAN;
> +		};
> +	};
> +};
> +
> +&bam_dmux {
> +	status = "okay";
> +};
> +
> +&bam_dmux_dma {
> +	status = "okay";
> +};
> +
> +&blsp1_uart2 {
> +	status = "okay";
> +};
> +
> +/* Remove &dsi_phy0 from clocks to make sure that gcc probes with display disabled */
> +&gcc {
> +	clocks = <&xo_board>, <&sleep_clk>, <0>, <0>, <0>, <0>, <0>;
> +};
> +
> +&mpss {
> +	pinctrl-0 = <&sim_ctrl_default>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +};
> +
> +&pm8916_usbin {
> +	status = "okay";
> +};
> +
> +&pronto {
> +	status = "okay";
> +};
> +
> +&sdhc_1 {
> +	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
> +	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
> +	pinctrl-names = "default", "sleep";
> +
> +	status = "okay";
> +};
> +
> +&usb {
> +	extcon = <&pm8916_usbin>;
> +	dr_mode = "peripheral";
> +
> +	status = "okay";
> +};
> +
> +&usb_hs_phy {
> +	extcon = <&pm8916_usbin>;
> +};
> +
> +&smd_rpm_regulators {
> +	vdd_l1_l2_l3-supply = <&pm8916_s3>;
> +	vdd_l4_l5_l6-supply = <&pm8916_s4>;
> +	vdd_l7-supply = <&pm8916_s4>;
> +
> +	s3 {
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1300000>;
> +	};
> +
> +	s4 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <2100000>;
> +	};
> +
> +	l1 {
> +		regulator-min-microvolt = <1225000>;
> +		regulator-max-microvolt = <1225000>;
> +	};
> +
> +	l2 {
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +	};
> +
> +	l4 {
> +		regulator-min-microvolt = <2050000>;
> +		regulator-max-microvolt = <2050000>;
> +	};
> +
> +	l5 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	l6 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	l7 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	l8 {
> +		regulator-min-microvolt = <2850000>;
> +		regulator-max-microvolt = <2900000>;
> +	};
> +
> +	l9 {
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l10 {
> +		regulator-min-microvolt = <2700000>;
> +		regulator-max-microvolt = <2800000>;
> +	};
> +
> +	l11 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <2950000>;
> +		regulator-system-load = <200000>;
> +		regulator-allow-set-load;
> +	};
> +
> +	l12 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <2950000>;
> +	};
> +
> +	l13 {
> +		regulator-min-microvolt = <3075000>;
> +		regulator-max-microvolt = <3075000>;
> +	};
> +
> +	l14 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l15 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l16 {
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	l17 {
> +		regulator-min-microvolt = <2850000>;
> +		regulator-max-microvolt = <2850000>;
> +	};
> +
> +	l18 {
> +		regulator-min-microvolt = <2700000>;
> +		regulator-max-microvolt = <2700000>;
> +	};
> +};
> +
> +&msmgpio {
> +	/* pins are board-specific */
> +	button_default: button-default-state {
> +		function = "gpio";
> +		drive-strength = <2>;
> +	};
> +
> +	gpio_leds_default: gpio-leds-default-state {
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	sim_ctrl_default: sim-ctrl-default-state {
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +		output-low;
> +	};
> +};
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index e442a81895d04..d83e02c84d42c 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -22,6 +22,8 @@  dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-e7.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-grandmax.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-j5.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-samsung-serranove.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-thwc-uf896.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-thwc-ufi001c.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8916-wingtech-wt88047.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-motorola-potter.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= msm8953-xiaomi-daisy.dtb
diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
new file mode 100644
index 0000000000000..c492db8561904
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-uf896.dts
@@ -0,0 +1,39 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-ufi.dtsi"
+
+/ {
+	model = "uf896 4G Modem Stick";
+	compatible = "thwc,uf896", "qcom,msm8916";
+};
+
+&button_restart {
+	gpios = <&msmgpio 35 GPIO_ACTIVE_LOW>;
+};
+
+&led_r {
+	gpios = <&msmgpio 82 GPIO_ACTIVE_HIGH>;
+};
+
+&led_g {
+	gpios = <&msmgpio 83 GPIO_ACTIVE_HIGH>;
+};
+
+&led_b {
+	gpios = <&msmgpio 81 GPIO_ACTIVE_HIGH>;
+};
+
+&button_default {
+	pins = "gpio35";
+	bias-pull-up;
+};
+
+&gpio_leds_default {
+	pins = "gpio81", "gpio82", "gpio83";
+};
+
+&sim_ctrl_default {
+	pins = "gpio1", "gpio2";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
new file mode 100644
index 0000000000000..700cf81cbf8c0
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-thwc-ufi001c.dts
@@ -0,0 +1,39 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+
+/dts-v1/;
+
+#include "msm8916-ufi.dtsi"
+
+/ {
+	model = "ufi-001c/ufi-001b 4G Modem Stick";
+	compatible = "thwc,ufi001c", "qcom,msm8916";
+};
+
+&button_restart {
+	gpios = <&msmgpio 37 GPIO_ACTIVE_HIGH>;
+};
+
+&led_r {
+	gpios = <&msmgpio 22 GPIO_ACTIVE_HIGH>;
+};
+
+&led_g {
+	gpios = <&msmgpio 21 GPIO_ACTIVE_HIGH>;
+};
+
+&led_b {
+	gpios = <&msmgpio 20 GPIO_ACTIVE_HIGH>;
+};
+
+&button_default {
+	pins = "gpio37";
+	bias-pull-down;
+};
+
+&gpio_leds_default {
+	pins = "gpio20", "gpio21", "gpio22";
+};
+
+&sim_ctrl_default {
+	pins = "gpio1", "gpio2";
+};
diff --git a/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
new file mode 100644
index 0000000000000..790a9696da9de
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/msm8916-ufi.dtsi
@@ -0,0 +1,250 @@ 
+// SPDX-License-Identifier: GPL-2.0-only
+
+#include "msm8916-pm8916.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+
+/ {
+	chassis-type = "embedded";
+
+	aliases {
+		serial0 = &blsp1_uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0";
+	};
+
+	reserved-memory {
+		mpss_mem: mpss@86800000 {
+			reg = <0x0 0x86800000 0x0 0x5500000>;
+			no-map;
+		};
+
+		gps_mem: gps@8bd00000 {
+			reg = <0x0 0x8bd00000 0x0 0x200000>;
+			no-map;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&button_default>;
+		pinctrl-names = "default";
+
+		label = "GPIO Buttons";
+
+		/* GPIO is board-specific */
+		button_restart: button-restart {
+			label = "Restart";
+			linux,code = <KEY_RESTART>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		pinctrl-0 = <&gpio_leds_default>;
+		pinctrl-names = "default";
+
+		/*
+		 * GPIOs are board-specific.
+		 * Functions and default-states defined here are fallbacks.
+		 * Feel free to override them if your board is different.
+		 */
+		led_r: led-r {
+			color = <LED_COLOR_ID_RED>;
+			default-state = "on";
+			function = LED_FUNCTION_POWER;
+		};
+
+		led_g: led-g {
+			color = <LED_COLOR_ID_GREEN>;
+			default-state = "off";
+			function = LED_FUNCTION_WLAN;
+		};
+
+		led_b: led-b {
+			color = <LED_COLOR_ID_BLUE>;
+			default-state = "off";
+			function = LED_FUNCTION_WAN;
+		};
+	};
+};
+
+&bam_dmux {
+	status = "okay";
+};
+
+&bam_dmux_dma {
+	status = "okay";
+};
+
+&blsp1_uart2 {
+	status = "okay";
+};
+
+/* Remove &dsi_phy0 from clocks to make sure that gcc probes with display disabled */
+&gcc {
+	clocks = <&xo_board>, <&sleep_clk>, <0>, <0>, <0>, <0>, <0>;
+};
+
+&mpss {
+	pinctrl-0 = <&sim_ctrl_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pm8916_usbin {
+	status = "okay";
+};
+
+&pronto {
+	status = "okay";
+};
+
+&sdhc_1 {
+	pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
+	pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
+	pinctrl-names = "default", "sleep";
+
+	status = "okay";
+};
+
+&usb {
+	extcon = <&pm8916_usbin>;
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&pm8916_usbin>;
+};
+
+&smd_rpm_regulators {
+	vdd_l1_l2_l3-supply = <&pm8916_s3>;
+	vdd_l4_l5_l6-supply = <&pm8916_s4>;
+	vdd_l7-supply = <&pm8916_s4>;
+
+	s3 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1300000>;
+	};
+
+	s4 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2100000>;
+	};
+
+	l1 {
+		regulator-min-microvolt = <1225000>;
+		regulator-max-microvolt = <1225000>;
+	};
+
+	l2 {
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+	};
+
+	l4 {
+		regulator-min-microvolt = <2050000>;
+		regulator-max-microvolt = <2050000>;
+	};
+
+	l5 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l6 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l7 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+	};
+
+	l8 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2900000>;
+	};
+
+	l9 {
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l10 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2800000>;
+	};
+
+	l11 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+		regulator-system-load = <200000>;
+		regulator-allow-set-load;
+	};
+
+	l12 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <2950000>;
+	};
+
+	l13 {
+		regulator-min-microvolt = <3075000>;
+		regulator-max-microvolt = <3075000>;
+	};
+
+	l14 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l15 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l16 {
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+	};
+
+	l17 {
+		regulator-min-microvolt = <2850000>;
+		regulator-max-microvolt = <2850000>;
+	};
+
+	l18 {
+		regulator-min-microvolt = <2700000>;
+		regulator-max-microvolt = <2700000>;
+	};
+};
+
+&msmgpio {
+	/* pins are board-specific */
+	button_default: button-default-state {
+		function = "gpio";
+		drive-strength = <2>;
+	};
+
+	gpio_leds_default: gpio-leds-default-state {
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sim_ctrl_default: sim-ctrl-default-state {
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+};