@@ -878,77 +878,10 @@ static void sd_config_write_same(struct scsi_disk *sdkp)
sdkp->zeroing_mode = SD_ZERO_WRITE;
out:
- blk_queue_max_write_same_sectors(q, sdkp->max_ws_blocks *
- (logical_block_size >> 9));
blk_queue_max_write_zeroes_sectors(q, sdkp->max_ws_blocks *
(logical_block_size >> 9));
}
-/**
- * sd_setup_write_same_cmnd - write the same data to multiple blocks
- * @cmd: command to prepare
- *
- * Will issue either WRITE SAME(10) or WRITE SAME(16) depending on
- * preference indicated by target device.
- **/
-static int sd_setup_write_same_cmnd(struct scsi_cmnd *cmd)
-{
- struct request *rq = cmd->request;
- struct scsi_device *sdp = cmd->device;
- struct scsi_disk *sdkp = scsi_disk(rq->rq_disk);
- struct bio *bio = rq->bio;
- sector_t sector = blk_rq_pos(rq);
- unsigned int nr_sectors = blk_rq_sectors(rq);
- unsigned int nr_bytes = blk_rq_bytes(rq);
- int ret;
-
- if (sdkp->device->no_write_same)
- return BLKPREP_INVALID;
-
- BUG_ON(bio_offset(bio) || bio_iovec(bio).bv_len != sdp->sector_size);
-
- if (sd_is_zoned(sdkp)) {
- ret = sd_zbc_setup_write_cmnd(cmd);
- if (ret != BLKPREP_OK)
- return ret;
- }
-
- sector >>= ilog2(sdp->sector_size) - 9;
- nr_sectors >>= ilog2(sdp->sector_size) - 9;
-
- rq->timeout = SD_WRITE_SAME_TIMEOUT;
-
- if (sdkp->ws16 || sector > 0xffffffff || nr_sectors > 0xffff) {
- cmd->cmd_len = 16;
- cmd->cmnd[0] = WRITE_SAME_16;
- put_unaligned_be64(sector, &cmd->cmnd[2]);
- put_unaligned_be32(nr_sectors, &cmd->cmnd[10]);
- } else {
- cmd->cmd_len = 10;
- cmd->cmnd[0] = WRITE_SAME;
- put_unaligned_be32(sector, &cmd->cmnd[2]);
- put_unaligned_be16(nr_sectors, &cmd->cmnd[7]);
- }
-
- cmd->transfersize = sdp->sector_size;
- cmd->allowed = SD_MAX_RETRIES;
-
- /*
- * For WRITE SAME the data transferred via the DATA OUT buffer is
- * different from the amount of data actually written to the target.
- *
- * We set up __data_len to the amount of data transferred via the
- * DATA OUT buffer so that blk_rq_map_sg sets up the proper S/G list
- * to transfer a single sector of data first, but then reset it to
- * the amount of data to be written right after so that the I/O path
- * knows how much to actually write.
- */
- rq->__data_len = sdp->sector_size;
- ret = scsi_init_io(cmd);
- rq->__data_len = nr_bytes;
- return ret;
-}
-
static int sd_setup_flush_cmnd(struct scsi_cmnd *cmd)
{
struct request *rq = cmd->request;
@@ -1232,8 +1165,6 @@ static int sd_init_command(struct scsi_cmnd *cmd)
}
case REQ_OP_WRITE_ZEROES:
return sd_setup_write_zeroes_cmnd(cmd);
- case REQ_OP_WRITE_SAME:
- return sd_setup_write_same_cmnd(cmd);
case REQ_OP_FLUSH:
return sd_setup_flush_cmnd(cmd);
case REQ_OP_READ:
@@ -1872,7 +1803,6 @@ static int sd_done(struct scsi_cmnd *SCpnt)
switch (req_op(req)) {
case REQ_OP_DISCARD:
case REQ_OP_WRITE_ZEROES:
- case REQ_OP_WRITE_SAME:
case REQ_OP_ZONE_RESET:
if (!result) {
good_bytes = blk_rq_bytes(req);
@@ -330,7 +330,6 @@ void sd_zbc_complete(struct scsi_cmnd *cmd,
switch (req_op(rq)) {
case REQ_OP_WRITE:
case REQ_OP_WRITE_ZEROES:
- case REQ_OP_WRITE_SAME:
case REQ_OP_ZONE_RESET:
/* Unlock the zone */
There are no more end-users of REQ_OP_WRITE_SAME left, so we can start deleting it. Signed-off-by: Christoph Hellwig <hch@lst.de> --- drivers/scsi/sd.c | 70 --------------------------------------------------- drivers/scsi/sd_zbc.c | 1 - 2 files changed, 71 deletions(-)