diff mbox series

[V10,1/8] block, bfq: split sync bfq_queues on a per-actuator basis

Message ID 20221209094442.36896-2-paolo.valente@linaro.org (mailing list archive)
State New, archived
Headers show
Series block, bfq: extend bfq to support multi-actuator drives | expand

Commit Message

Paolo Valente Dec. 9, 2022, 9:44 a.m. UTC
Single-LUN multi-actuator SCSI drives, as well as all multi-actuator
SATA drives appear as a single device to the I/O subsystem [1].  Yet
they address commands to different actuators internally, as a function
of Logical Block Addressing (LBAs). A given sector is reachable by
only one of the actuators. For example, Seagate’s Serial Advanced
Technology Attachment (SATA) version contains two actuators and maps
the lower half of the SATA LBA space to the lower actuator and the
upper half to the upper actuator.

Evidently, to fully utilize actuators, no actuator must be left idle
or underutilized while there is pending I/O for it. The block layer
must somehow control the load of each actuator individually. This
commit lays the ground for allowing BFQ to provide such a per-actuator
control.

BFQ associates an I/O-request sync bfq_queue with each process doing
synchronous I/O, or with a group of processes, in case of queue
merging. Then BFQ serves one bfq_queue at a time. While in service, a
bfq_queue is emptied in request-position order. Yet the same process,
or group of processes, may generate I/O for different actuators. In
this case, different streams of I/O (each for a different actuator)
get all inserted into the same sync bfq_queue. So there is basically
no individual control on when each stream is served, i.e., on when the
I/O requests of the stream are picked from the bfq_queue and
dispatched to the drive.

This commit enables BFQ to control the service of each actuator
individually for synchronous I/O, by simply splitting each sync
bfq_queue into N queues, one for each actuator. In other words, a sync
bfq_queue is now associated to a pair (process, actuator). As a
consequence of this split, the per-queue proportional-share policy
implemented by BFQ will guarantee that the sync I/O generated for each
actuator, by each process, receives its fair share of service.

This is just a preparatory patch. If the I/O of the same process
happens to be sent to different queues, then each of these queues may
undergo queue merging. To handle this event, the bfq_io_cq data
structure must be properly extended. In addition, stable merging must
be disabled to avoid loss of control on individual actuators. Finally,
also async queues must be split. These issues are described in detail
and addressed in next commits. As for this commit, although multiple
per-process bfq_queues are provided, the I/O of each process or group
of processes is still sent to only one queue, regardless of the
actuator the I/O is for. The forwarding to distinct bfq_queues will be
enabled after addressing the above issues.

[1] https://www.linaro.org/blog/budget-fair-queueing-bfq-linux-io-scheduler-optimizations-for-multi-actuator-sata-hard-drives/

Signed-off-by: Gabriele Felici <felicigb@gmail.com>
Signed-off-by: Carmine Zaccagnino <carmine@carminezacc.com>
Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
---
 block/bfq-cgroup.c  |  92 ++++++++++++++------------
 block/bfq-iosched.c | 158 +++++++++++++++++++++++++++++---------------
 block/bfq-iosched.h |  51 +++++++++++---
 3 files changed, 195 insertions(+), 106 deletions(-)

Comments

Damien Le Moal Dec. 16, 2022, midnight UTC | #1
On 12/9/22 18:44, Paolo Valente wrote:
> Single-LUN multi-actuator SCSI drives, as well as all multi-actuator
> SATA drives appear as a single device to the I/O subsystem [1].  Yet
> they address commands to different actuators internally, as a function
> of Logical Block Addressing (LBAs). A given sector is reachable by
> only one of the actuators. For example, Seagate’s Serial Advanced
> Technology Attachment (SATA) version contains two actuators and maps
> the lower half of the SATA LBA space to the lower actuator and the
> upper half to the upper actuator.
> 
> Evidently, to fully utilize actuators, no actuator must be left idle
> or underutilized while there is pending I/O for it. The block layer
> must somehow control the load of each actuator individually. This
> commit lays the ground for allowing BFQ to provide such a per-actuator
> control.
> 
> BFQ associates an I/O-request sync bfq_queue with each process doing
> synchronous I/O, or with a group of processes, in case of queue
> merging. Then BFQ serves one bfq_queue at a time. While in service, a
> bfq_queue is emptied in request-position order. Yet the same process,
> or group of processes, may generate I/O for different actuators. In
> this case, different streams of I/O (each for a different actuator)
> get all inserted into the same sync bfq_queue. So there is basically
> no individual control on when each stream is served, i.e., on when the
> I/O requests of the stream are picked from the bfq_queue and
> dispatched to the drive.
> 
> This commit enables BFQ to control the service of each actuator
> individually for synchronous I/O, by simply splitting each sync
> bfq_queue into N queues, one for each actuator. In other words, a sync
> bfq_queue is now associated to a pair (process, actuator). As a
> consequence of this split, the per-queue proportional-share policy
> implemented by BFQ will guarantee that the sync I/O generated for each
> actuator, by each process, receives its fair share of service.
> 
> This is just a preparatory patch. If the I/O of the same process
> happens to be sent to different queues, then each of these queues may
> undergo queue merging. To handle this event, the bfq_io_cq data
> structure must be properly extended. In addition, stable merging must
> be disabled to avoid loss of control on individual actuators. Finally,
> also async queues must be split. These issues are described in detail
> and addressed in next commits. As for this commit, although multiple
> per-process bfq_queues are provided, the I/O of each process or group
> of processes is still sent to only one queue, regardless of the
> actuator the I/O is for. The forwarding to distinct bfq_queues will be
> enabled after addressing the above issues.
> 
> [1] https://www.linaro.org/blog/budget-fair-queueing-bfq-linux-io-scheduler-optimizations-for-multi-actuator-sata-hard-drives/
> 
> Signed-off-by: Gabriele Felici <felicigb@gmail.com>
> Signed-off-by: Carmine Zaccagnino <carmine@carminezacc.com>
> Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
> ---
>  block/bfq-cgroup.c  |  92 ++++++++++++++------------
>  block/bfq-iosched.c | 158 +++++++++++++++++++++++++++++---------------
>  block/bfq-iosched.h |  51 +++++++++++---
>  3 files changed, 195 insertions(+), 106 deletions(-)
> 
> diff --git a/block/bfq-cgroup.c b/block/bfq-cgroup.c
> index 7d624a3a3f0f..7ea77f994424 100644
> --- a/block/bfq-cgroup.c
> +++ b/block/bfq-cgroup.c
> @@ -704,6 +704,47 @@ void bfq_bfqq_move(struct bfq_data *bfqd, struct bfq_queue *bfqq,
>  	bfq_put_queue(bfqq);
>  }
>  
> +static void bfq_sync_bfqq_move(struct bfq_data *bfqd,
> +			       struct bfq_queue *sync_bfqq,
> +			       struct bfq_io_cq *bic,
> +			       struct bfq_group *bfqg,
> +			       unsigned int act_idx)
> +{
> +	struct bfq_queue *bfqq;
> +
> +	if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
> +		/* We are the only user of this bfqq, just move it */
> +		if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
> +			bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
> +		return;
> +	}
> +
> +	/*
> +	 * The queue was merged to a different queue. Check
> +	 * that the merge chain still belongs to the same
> +	 * cgroup.
> +	 */
> +	for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
> +		if (bfqq->entity.sched_data !=
> +		    &bfqg->sched_data)

Already commented on this one: please do not split this line. The code
looks silly like this.

> +			break;
> +	if (bfqq) {
> +		/*
> +		 * Some queue changed cgroup so the merge is not valid
> +		 * anymore. We cannot easily just cancel the merge (by
> +		 * clearing new_bfqq) as there may be other processes
> +		 * using this queue and holding refs to all queues
> +		 * below sync_bfqq->new_bfqq. Similarly if the merge
> +		 * already happened, we need to detach from bfqq now
> +		 * so that we cannot merge bio to a request from the
> +		 * old cgroup.
> +		 */
> +		bfq_put_cooperator(sync_bfqq);
> +		bfq_release_process_ref(bfqd, sync_bfqq);
> +		bic_set_bfqq(bic, NULL, true, act_idx);
> +	}
> +}
> +
>  /**
>   * __bfq_bic_change_cgroup - move @bic to @bfqg.
>   * @bfqd: the queue descriptor.
> @@ -718,53 +759,20 @@ static void *__bfq_bic_change_cgroup(struct bfq_data *bfqd,
>  				     struct bfq_io_cq *bic,
>  				     struct bfq_group *bfqg)
>  {
> -	struct bfq_queue *async_bfqq = bic_to_bfqq(bic, 0);
> -	struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, 1);
> -	struct bfq_entity *entity;
> +	unsigned int act_idx;
>  
> -	if (async_bfqq) {
> -		entity = &async_bfqq->entity;
> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
> +		struct bfq_queue *async_bfqq = bic_to_bfqq(bic, false, act_idx);
> +		struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, true, act_idx);
>  
> -		if (entity->sched_data != &bfqg->sched_data) {
> -			bic_set_bfqq(bic, NULL, 0);
> +		if (async_bfqq &&
> +		    async_bfqq->entity.sched_data != &bfqg->sched_data) {
> +			bic_set_bfqq(bic, NULL, false, act_idx);
>  			bfq_release_process_ref(bfqd, async_bfqq);
>  		}
> -	}
>  
> -	if (sync_bfqq) {
> -		if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
> -			/* We are the only user of this bfqq, just move it */
> -			if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
> -				bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
> -		} else {
> -			struct bfq_queue *bfqq;
> -
> -			/*
> -			 * The queue was merged to a different queue. Check
> -			 * that the merge chain still belongs to the same
> -			 * cgroup.
> -			 */
> -			for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
> -				if (bfqq->entity.sched_data !=
> -				    &bfqg->sched_data)
> -					break;
> -			if (bfqq) {
> -				/*
> -				 * Some queue changed cgroup so the merge is
> -				 * not valid anymore. We cannot easily just
> -				 * cancel the merge (by clearing new_bfqq) as
> -				 * there may be other processes using this
> -				 * queue and holding refs to all queues below
> -				 * sync_bfqq->new_bfqq. Similarly if the merge
> -				 * already happened, we need to detach from
> -				 * bfqq now so that we cannot merge bio to a
> -				 * request from the old cgroup.
> -				 */
> -				bfq_put_cooperator(sync_bfqq);
> -				bfq_release_process_ref(bfqd, sync_bfqq);
> -				bic_set_bfqq(bic, NULL, 1);
> -			}
> -		}
> +		if (sync_bfqq)
> +			bfq_sync_bfqq_move(bfqd, sync_bfqq, bic, bfqg, act_idx);
>  	}
>  
>  	return bfqg;
> diff --git a/block/bfq-iosched.c b/block/bfq-iosched.c
> index 7ea427817f7f..16dbf52ce74b 100644
> --- a/block/bfq-iosched.c
> +++ b/block/bfq-iosched.c
> @@ -377,14 +377,21 @@ static const unsigned long bfq_late_stable_merging = 600;
>  #define RQ_BIC(rq)		((struct bfq_io_cq *)((rq)->elv.priv[0]))
>  #define RQ_BFQQ(rq)		((rq)->elv.priv[1])
>  
> -struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync)
> +struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync,
> +			      unsigned int actuator_idx)
>  {
> -	return bic->bfqq[is_sync];
> +	if (is_sync)
> +		return bic->bfqq[1][actuator_idx];
> +
> +	return bic->bfqq[0][actuator_idx];
>  }
>  
>  static void bfq_put_stable_ref(struct bfq_queue *bfqq);
>  
> -void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
> +void bic_set_bfqq(struct bfq_io_cq *bic,
> +		  struct bfq_queue *bfqq,
> +		  bool is_sync,
> +		  unsigned int actuator_idx)
>  {
>  	/*
>  	 * If bfqq != NULL, then a non-stable queue merge between
> @@ -399,7 +406,10 @@ void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
>  	 * we cancel the stable merge if
>  	 * bic->stable_merge_bfqq == bfqq.
>  	 */
> -	bic->bfqq[is_sync] = bfqq;
> +	if (is_sync)
> +		bic->bfqq[1][actuator_idx] = bfqq;
> +	else
> +		bic->bfqq[0][actuator_idx] = bfqq;
>  
>  	if (bfqq && bic->stable_merge_bfqq == bfqq) {
>  		/*
> @@ -672,9 +682,9 @@ static void bfq_limit_depth(blk_opf_t opf, struct blk_mq_alloc_data *data)
>  {
>  	struct bfq_data *bfqd = data->q->elevator->elevator_data;
>  	struct bfq_io_cq *bic = bfq_bic_lookup(data->q);
> -	struct bfq_queue *bfqq = bic ? bic_to_bfqq(bic, op_is_sync(opf)) : NULL;
>  	int depth;
>  	unsigned limit = data->q->nr_requests;
> +	unsigned int act_idx;
>  
>  	/* Sync reads have full depth available */
>  	if (op_is_sync(opf) && !op_is_write(opf)) {
> @@ -684,14 +694,21 @@ static void bfq_limit_depth(blk_opf_t opf, struct blk_mq_alloc_data *data)
>  		limit = (limit * depth) >> bfqd->full_depth_shift;
>  	}
>  
> -	/*
> -	 * Does queue (or any parent entity) exceed number of requests that
> -	 * should be available to it? Heavily limit depth so that it cannot
> -	 * consume more available requests and thus starve other entities.
> -	 */
> -	if (bfqq && bfqq_request_over_limit(bfqq, limit))
> -		depth = 1;
> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
> +		struct bfq_queue *bfqq =
> +			bic ? bic_to_bfqq(bic, op_is_sync(opf), act_idx) : NULL;

Commented already: why not add a "if (!bfqq) return NULL;" in
bic_to_bfqq() ?

>  
> +		/*
> +		 * Does queue (or any parent entity) exceed number of
> +		 * requests that should be available to it? Heavily
> +		 * limit depth so that it cannot consume more
> +		 * available requests and thus starve other entities.
> +		 */
> +		if (bfqq && bfqq_request_over_limit(bfqq, limit)) {
> +			depth = 1;
> +			break;
> +		}
> +	}
>  	bfq_log(bfqd, "[%s] wr_busy %d sync %d depth %u",
>  		__func__, bfqd->wr_busy_queues, op_is_sync(opf), depth);
>  	if (depth)
> @@ -1812,6 +1829,18 @@ static bool bfq_bfqq_higher_class_or_weight(struct bfq_queue *bfqq,
>  	return bfqq_weight > in_serv_weight;
>  }
>  
> +/*
> + * Get the index of the actuator that will serve bio.
> + */
> +static unsigned int bfq_actuator_index(struct bfq_data *bfqd, struct bio *bio)
> +{
> +	/*
> +	 * Multi-actuator support not complete yet, so always return 0
> +	 * for the moment (to keep incomplete mechanisms off).
> +	 */
> +	return 0;
> +}
> +
>  static bool bfq_better_to_idle(struct bfq_queue *bfqq);
>  
>  static void bfq_bfqq_handle_idle_busy_switch(struct bfq_data *bfqd,
> @@ -2142,7 +2171,7 @@ static void bfq_check_waker(struct bfq_data *bfqd, struct bfq_queue *bfqq,
>  	 * We reset waker detection logic also if too much time has passed
>   	 * since the first detection. If wakeups are rare, pointless idling
>  	 * doesn't hurt throughput that much. The condition below makes sure
> -	 * we do not uselessly idle blocking waker in more than 1/64 cases. 
> +	 * we do not uselessly idle blocking waker in more than 1/64 cases.
>  	 */
>  	if (bfqd->last_completed_rq_bfqq !=
>  	    bfqq->tentative_waker_bfqq ||
> @@ -2478,7 +2507,8 @@ static bool bfq_bio_merge(struct request_queue *q, struct bio *bio,
>  		 */
>  		bfq_bic_update_cgroup(bic, bio);
>  
> -		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf));
> +		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf),
> +					     bfq_actuator_index(bfqd, bio));
>  	} else {
>  		bfqd->bio_bfqq = NULL;
>  	}
> @@ -3174,7 +3204,7 @@ bfq_merge_bfqqs(struct bfq_data *bfqd, struct bfq_io_cq *bic,
>  	/*
>  	 * Merge queues (that is, let bic redirect its requests to new_bfqq)
>  	 */
> -	bic_set_bfqq(bic, new_bfqq, 1);
> +	bic_set_bfqq(bic, new_bfqq, true, bfqq->actuator_idx);
>  	bfq_mark_bfqq_coop(new_bfqq);
>  	/*
>  	 * new_bfqq now belongs to at least two bics (it is a shared queue):
> @@ -4808,11 +4838,8 @@ static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
>  	 */
>  	if (bfq_bfqq_wait_request(bfqq) ||
>  	    (bfqq->dispatched != 0 && bfq_better_to_idle(bfqq))) {
> -		struct bfq_queue *async_bfqq =
> -			bfqq->bic && bfqq->bic->bfqq[0] &&
> -			bfq_bfqq_busy(bfqq->bic->bfqq[0]) &&
> -			bfqq->bic->bfqq[0]->next_rq ?
> -			bfqq->bic->bfqq[0] : NULL;
> +		unsigned int act_idx = bfqq->actuator_idx;
> +		struct bfq_queue *async_bfqq = NULL;
>  		struct bfq_queue *blocked_bfqq =
>  			!hlist_empty(&bfqq->woken_list) ?
>  			container_of(bfqq->woken_list.first,
> @@ -4820,6 +4847,10 @@ static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
>  				     woken_list_node)
>  			: NULL;
>  
> +		if (bfqq->bic && bfqq->bic->bfqq[0][act_idx] &&
> +		    bfq_bfqq_busy(bfqq->bic->bfqq[0][act_idx]) &&
> +		    bfqq->bic->bfqq[0][act_idx]->next_rq)
> +			async_bfqq = bfqq->bic->bfqq[0][act_idx];
>  		/*
>  		 * The next four mutually-exclusive ifs decide
>  		 * whether to try injection, and choose the queue to
> @@ -4904,7 +4935,7 @@ static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
>  		    icq_to_bic(async_bfqq->next_rq->elv.icq) == bfqq->bic &&
>  		    bfq_serv_to_charge(async_bfqq->next_rq, async_bfqq) <=
>  		    bfq_bfqq_budget_left(async_bfqq))
> -			bfqq = bfqq->bic->bfqq[0];
> +			bfqq = bfqq->bic->bfqq[0][act_idx];
>  		else if (bfqq->waker_bfqq &&
>  			   bfq_bfqq_busy(bfqq->waker_bfqq) &&
>  			   bfqq->waker_bfqq->next_rq &&
> @@ -5365,49 +5396,55 @@ static void bfq_exit_bfqq(struct bfq_data *bfqd, struct bfq_queue *bfqq)
>  	bfq_release_process_ref(bfqd, bfqq);
>  }
>  
> -static void bfq_exit_icq_bfqq(struct bfq_io_cq *bic, bool is_sync)
> +static void bfq_exit_icq_bfqq(struct bfq_io_cq *bic, bool is_sync,
> +			      unsigned int actuator_idx)
>  {
> -	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync);
> +	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync, actuator_idx);
>  	struct bfq_data *bfqd;
>  
>  	if (bfqq)
>  		bfqd = bfqq->bfqd; /* NULL if scheduler already exited */
>  
>  	if (bfqq && bfqd) {
> -		unsigned long flags;
> -
> -		spin_lock_irqsave(&bfqd->lock, flags);
>  		bfqq->bic = NULL;
>  		bfq_exit_bfqq(bfqd, bfqq);
> -		bic_set_bfqq(bic, NULL, is_sync);
> -		spin_unlock_irqrestore(&bfqd->lock, flags);
> +		bic_set_bfqq(bic, NULL, is_sync, actuator_idx);
>  	}
>  }
>  
>  static void bfq_exit_icq(struct io_cq *icq)
>  {
>  	struct bfq_io_cq *bic = icq_to_bic(icq);
> +	struct bfq_data *bfqd = bic_to_bfqd(bic);
> +	unsigned long flags;
> +	unsigned int act_idx;
> +	/*
> +	 * If bfqd and thus bfqd->num_actuators is not available any
> +	 * longer, then cycle over all possible per-actuator bfqqs in
> +	 * next loop. We rely on bic being zeroed on creation, and
> +	 * therefore on its unused per-actuator fields being NULL.
> +	 */
> +	unsigned int num_actuators = BFQ_MAX_ACTUATORS;
>  
> -	if (bic->stable_merge_bfqq) {
> -		struct bfq_data *bfqd = bic->stable_merge_bfqq->bfqd;
> +	/*
> +	 * bfqd is NULL if scheduler already exited, and in that case
> +	 * this is the last time these queues are accessed.
> +	 */
> +	if (bfqd) {
> +		spin_lock_irqsave(&bfqd->lock, flags);
> +		num_actuators = bfqd->num_actuators;
> +	}
>  
> -		/*
> -		 * bfqd is NULL if scheduler already exited, and in
> -		 * that case this is the last time bfqq is accessed.
> -		 */
> -		if (bfqd) {
> -			unsigned long flags;
> +	if (bic->stable_merge_bfqq)
> +		bfq_put_stable_ref(bic->stable_merge_bfqq);
>  
> -			spin_lock_irqsave(&bfqd->lock, flags);
> -			bfq_put_stable_ref(bic->stable_merge_bfqq);
> -			spin_unlock_irqrestore(&bfqd->lock, flags);
> -		} else {
> -			bfq_put_stable_ref(bic->stable_merge_bfqq);
> -		}
> +	for (act_idx = 0; act_idx < num_actuators; act_idx++) {
> +		bfq_exit_icq_bfqq(bic, true, act_idx);
> +		bfq_exit_icq_bfqq(bic, false, act_idx);
>  	}
>  
> -	bfq_exit_icq_bfqq(bic, true);
> -	bfq_exit_icq_bfqq(bic, false);
> +	if (bfqd)
> +		spin_unlock_irqrestore(&bfqd->lock, flags);
>  }
>  
>  /*
> @@ -5484,23 +5521,25 @@ static void bfq_check_ioprio_change(struct bfq_io_cq *bic, struct bio *bio)
>  
>  	bic->ioprio = ioprio;
>  
> -	bfqq = bic_to_bfqq(bic, false);
> +	bfqq = bic_to_bfqq(bic, false, bfq_actuator_index(bfqd, bio));
>  	if (bfqq) {
>  		bfq_release_process_ref(bfqd, bfqq);
>  		bfqq = bfq_get_queue(bfqd, bio, false, bic, true);
> -		bic_set_bfqq(bic, bfqq, false);
> +		bic_set_bfqq(bic, bfqq, false, bfq_actuator_index(bfqd, bio));
>  	}
>  
> -	bfqq = bic_to_bfqq(bic, true);
> +	bfqq = bic_to_bfqq(bic, true, bfq_actuator_index(bfqd, bio));
>  	if (bfqq)
>  		bfq_set_next_ioprio_data(bfqq, bic);
>  }
>  
>  static void bfq_init_bfqq(struct bfq_data *bfqd, struct bfq_queue *bfqq,
> -			  struct bfq_io_cq *bic, pid_t pid, int is_sync)
> +			  struct bfq_io_cq *bic, pid_t pid, int is_sync,
> +			  unsigned int act_idx)
>  {
>  	u64 now_ns = ktime_get_ns();
>  
> +	bfqq->actuator_idx = act_idx;
>  	RB_CLEAR_NODE(&bfqq->entity.rb_node);
>  	INIT_LIST_HEAD(&bfqq->fifo);
>  	INIT_HLIST_NODE(&bfqq->burst_list_node);
> @@ -5753,7 +5792,7 @@ static struct bfq_queue *bfq_get_queue(struct bfq_data *bfqd,
>  
>  	if (bfqq) {
>  		bfq_init_bfqq(bfqd, bfqq, bic, current->pid,
> -			      is_sync);
> +			      is_sync, bfq_actuator_index(bfqd, bio));
>  		bfq_init_entity(&bfqq->entity, bfqg);
>  		bfq_log_bfqq(bfqd, bfqq, "allocated");
>  	} else {
> @@ -6068,7 +6107,8 @@ static bool __bfq_insert_request(struct bfq_data *bfqd, struct request *rq)
>  		 * then complete the merge and redirect it to
>  		 * new_bfqq.
>  		 */
> -		if (bic_to_bfqq(RQ_BIC(rq), 1) == bfqq)
> +		if (bic_to_bfqq(RQ_BIC(rq), true,
> +				bfq_actuator_index(bfqd, rq->bio)) == bfqq)
>  			bfq_merge_bfqqs(bfqd, RQ_BIC(rq),
>  					bfqq, new_bfqq);
>  
> @@ -6622,7 +6662,7 @@ bfq_split_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq)
>  		return bfqq;
>  	}
>  
> -	bic_set_bfqq(bic, NULL, 1);
> +	bic_set_bfqq(bic, NULL, true, bfqq->actuator_idx);
>  
>  	bfq_put_cooperator(bfqq);
>  
> @@ -6636,7 +6676,8 @@ static struct bfq_queue *bfq_get_bfqq_handle_split(struct bfq_data *bfqd,
>  						   bool split, bool is_sync,
>  						   bool *new_queue)
>  {
> -	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync);
> +	unsigned int act_idx = bfq_actuator_index(bfqd, bio);
> +	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync, act_idx);
>  
>  	if (likely(bfqq && bfqq != &bfqd->oom_bfqq))
>  		return bfqq;
> @@ -6648,7 +6689,7 @@ static struct bfq_queue *bfq_get_bfqq_handle_split(struct bfq_data *bfqd,
>  		bfq_put_queue(bfqq);
>  	bfqq = bfq_get_queue(bfqd, bio, is_sync, bic, split);
>  
> -	bic_set_bfqq(bic, bfqq, is_sync);
> +	bic_set_bfqq(bic, bfqq, is_sync, act_idx);
>  	if (split && is_sync) {
>  		if ((bic->was_in_burst_list && bfqd->large_burst) ||
>  		    bic->saved_in_large_burst)
> @@ -7090,8 +7131,10 @@ static int bfq_init_queue(struct request_queue *q, struct elevator_type *e)
>  	 * Our fallback bfqq if bfq_find_alloc_queue() runs into OOM issues.
>  	 * Grab a permanent reference to it, so that the normal code flow
>  	 * will not attempt to free it.
> +	 * Set zero as actuator index: we will pretend that
> +	 * all I/O requests are for the same actuator.
>  	 */
> -	bfq_init_bfqq(bfqd, &bfqd->oom_bfqq, NULL, 1, 0);
> +	bfq_init_bfqq(bfqd, &bfqd->oom_bfqq, NULL, 1, 0, 0);
>  	bfqd->oom_bfqq.ref++;
>  	bfqd->oom_bfqq.new_ioprio = BFQ_DEFAULT_QUEUE_IOPRIO;
>  	bfqd->oom_bfqq.new_ioprio_class = IOPRIO_CLASS_BE;
> @@ -7110,6 +7153,13 @@ static int bfq_init_queue(struct request_queue *q, struct elevator_type *e)
>  
>  	bfqd->queue = q;
>  
> +	/*
> +	 * Multi-actuator support not complete yet, unconditionally
> +	 * set to only one actuator for the moment (to keep incomplete
> +	 * mechanisms off).
> +	 */
> +	bfqd->num_actuators = 1;
> +
>  	INIT_LIST_HEAD(&bfqd->dispatch);
>  
>  	hrtimer_init(&bfqd->idle_slice_timer, CLOCK_MONOTONIC,
> diff --git a/block/bfq-iosched.h b/block/bfq-iosched.h
> index 71f721670ab6..2b413ddffbb9 100644
> --- a/block/bfq-iosched.h
> +++ b/block/bfq-iosched.h
> @@ -33,6 +33,14 @@
>   */
>  #define BFQ_SOFTRT_WEIGHT_FACTOR	100
>  
> +/*
> + * Maximum number of actuators supported. This constant is used simply
> + * to define the size of the static array that will contain
> + * per-actuator data. The current value is hopefully a good upper
> + * bound to the possible number of actuators of any actual drive.
> + */
> +#define BFQ_MAX_ACTUATORS 8
> +
>  struct bfq_entity;
>  
>  /**
> @@ -225,12 +233,14 @@ struct bfq_ttime {
>   * struct bfq_queue - leaf schedulable entity.
>   *
>   * A bfq_queue is a leaf request queue; it can be associated with an
> - * io_context or more, if it  is  async or shared  between  cooperating
> - * processes. @cgroup holds a reference to the cgroup, to be sure that it
> - * does not disappear while a bfqq still references it (mostly to avoid
> - * races between request issuing and task migration followed by cgroup
> - * destruction).
> - * All the fields are protected by the queue lock of the containing bfqd.
> + * io_context or more, if it is async or shared between cooperating
> + * processes. Besides, it contains I/O requests for only one actuator
> + * (an io_context is associated with a different bfq_queue for each
> + * actuator it generates I/O for). @cgroup holds a reference to the
> + * cgroup, to be sure that it does not disappear while a bfqq still
> + * references it (mostly to avoid races between request issuing and
> + * task migration followed by cgroup destruction).  All the fields are
> + * protected by the queue lock of the containing bfqd.
>   */
>  struct bfq_queue {
>  	/* reference counter */
> @@ -395,6 +405,9 @@ struct bfq_queue {
>  	 * the woken queues when this queue exits.
>  	 */
>  	struct hlist_head woken_list;
> +
> +	/* index of the actuator this queue is associated with */
> +	unsigned int actuator_idx;
>  };
>  
>  /**
> @@ -403,8 +416,17 @@ struct bfq_queue {
>  struct bfq_io_cq {
>  	/* associated io_cq structure */
>  	struct io_cq icq; /* must be the first member */
> -	/* array of two process queues, the sync and the async */
> -	struct bfq_queue *bfqq[2];
> +	/*
> +	 * Matrix of associated process queues: first row for async
> +	 * queues, second row sync queues. Each row contains one
> +	 * column for each actuator. An I/O request generated by the
> +	 * process is inserted into the queue pointed by bfqq[i][j] if
> +	 * the request is to be served by the j-th actuator of the
> +	 * drive, where i==0 or i==1, depending on whether the request
> +	 * is async or sync. So there is a distinct queue for each
> +	 * actuator.
> +	 */
> +	struct bfq_queue *bfqq[2][BFQ_MAX_ACTUATORS];
>  	/* per (request_queue, blkcg) ioprio */
>  	int ioprio;
>  #ifdef CONFIG_BFQ_GROUP_IOSCHED
> @@ -768,6 +790,13 @@ struct bfq_data {
>  	 */
>  	unsigned int word_depths[2][2];
>  	unsigned int full_depth_shift;
> +
> +	/*
> +	 * Number of independent actuators. This is equal to 1 in
> +	 * case of single-actuator drives.
> +	 */
> +	unsigned int num_actuators;
> +
>  };
>  
>  enum bfqq_state_flags {
> @@ -964,8 +993,10 @@ struct bfq_group {
>  
>  extern const int bfq_timeout;
>  
> -struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync);
> -void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync);
> +struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync,
> +				unsigned int actuator_idx);
> +void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync,
> +				unsigned int actuator_idx);
>  struct bfq_data *bic_to_bfqd(struct bfq_io_cq *bic);
>  void bfq_pos_tree_add_move(struct bfq_data *bfqd, struct bfq_queue *bfqq);
>  void bfq_weights_tree_add(struct bfq_data *bfqd, struct bfq_queue *bfqq,
Paolo Valente Dec. 20, 2022, 1:10 p.m. UTC | #2
> Il giorno 16 dic 2022, alle ore 01:00, Damien Le Moal <damien.lemoal@opensource.wdc.com> ha scritto:
> 
> On 12/9/22 18:44, Paolo Valente wrote:
>> Single-LUN multi-actuator SCSI drives, as well as all multi-actuator
>> SATA drives appear as a single device to the I/O subsystem [1].  Yet
>> they address commands to different actuators internally, as a function
>> of Logical Block Addressing (LBAs). A given sector is reachable by
>> only one of the actuators. For example, Seagate’s Serial Advanced
>> Technology Attachment (SATA) version contains two actuators and maps
>> the lower half of the SATA LBA space to the lower actuator and the
>> upper half to the upper actuator.
>> 
>> Evidently, to fully utilize actuators, no actuator must be left idle
>> or underutilized while there is pending I/O for it. The block layer
>> must somehow control the load of each actuator individually. This
>> commit lays the ground for allowing BFQ to provide such a per-actuator
>> control.
>> 
>> BFQ associates an I/O-request sync bfq_queue with each process doing
>> synchronous I/O, or with a group of processes, in case of queue
>> merging. Then BFQ serves one bfq_queue at a time. While in service, a
>> bfq_queue is emptied in request-position order. Yet the same process,
>> or group of processes, may generate I/O for different actuators. In
>> this case, different streams of I/O (each for a different actuator)
>> get all inserted into the same sync bfq_queue. So there is basically
>> no individual control on when each stream is served, i.e., on when the
>> I/O requests of the stream are picked from the bfq_queue and
>> dispatched to the drive.
>> 
>> This commit enables BFQ to control the service of each actuator
>> individually for synchronous I/O, by simply splitting each sync
>> bfq_queue into N queues, one for each actuator. In other words, a sync
>> bfq_queue is now associated to a pair (process, actuator). As a
>> consequence of this split, the per-queue proportional-share policy
>> implemented by BFQ will guarantee that the sync I/O generated for each
>> actuator, by each process, receives its fair share of service.
>> 
>> This is just a preparatory patch. If the I/O of the same process
>> happens to be sent to different queues, then each of these queues may
>> undergo queue merging. To handle this event, the bfq_io_cq data
>> structure must be properly extended. In addition, stable merging must
>> be disabled to avoid loss of control on individual actuators. Finally,
>> also async queues must be split. These issues are described in detail
>> and addressed in next commits. As for this commit, although multiple
>> per-process bfq_queues are provided, the I/O of each process or group
>> of processes is still sent to only one queue, regardless of the
>> actuator the I/O is for. The forwarding to distinct bfq_queues will be
>> enabled after addressing the above issues.
>> 
>> [1] https://www.linaro.org/blog/budget-fair-queueing-bfq-linux-io-scheduler-optimizations-for-multi-actuator-sata-hard-drives/
>> 
>> Signed-off-by: Gabriele Felici <felicigb@gmail.com>
>> Signed-off-by: Carmine Zaccagnino <carmine@carminezacc.com>
>> Signed-off-by: Paolo Valente <paolo.valente@linaro.org>
>> ---
>> block/bfq-cgroup.c  |  92 ++++++++++++++------------
>> block/bfq-iosched.c | 158 +++++++++++++++++++++++++++++---------------
>> block/bfq-iosched.h |  51 +++++++++++---
>> 3 files changed, 195 insertions(+), 106 deletions(-)
>> 
>> diff --git a/block/bfq-cgroup.c b/block/bfq-cgroup.c
>> index 7d624a3a3f0f..7ea77f994424 100644
>> --- a/block/bfq-cgroup.c
>> +++ b/block/bfq-cgroup.c
>> @@ -704,6 +704,47 @@ void bfq_bfqq_move(struct bfq_data *bfqd, struct bfq_queue *bfqq,
>> 	bfq_put_queue(bfqq);
>> }
>> 
>> +static void bfq_sync_bfqq_move(struct bfq_data *bfqd,
>> +			       struct bfq_queue *sync_bfqq,
>> +			       struct bfq_io_cq *bic,
>> +			       struct bfq_group *bfqg,
>> +			       unsigned int act_idx)
>> +{
>> +	struct bfq_queue *bfqq;
>> +
>> +	if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
>> +		/* We are the only user of this bfqq, just move it */
>> +		if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
>> +			bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
>> +		return;
>> +	}
>> +
>> +	/*
>> +	 * The queue was merged to a different queue. Check
>> +	 * that the merge chain still belongs to the same
>> +	 * cgroup.
>> +	 */
>> +	for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
>> +		if (bfqq->entity.sched_data !=
>> +		    &bfqg->sched_data)
> 
> Already commented on this one: please do not split this line. The code
> looks silly like this.

Actually this mistake was in other places, sorry for this extra one.
Fixed in upcoming version.

> 
>> +			break;
>> +	if (bfqq) {
>> +		/*
>> +		 * Some queue changed cgroup so the merge is not valid
>> +		 * anymore. We cannot easily just cancel the merge (by
>> +		 * clearing new_bfqq) as there may be other processes
>> +		 * using this queue and holding refs to all queues
>> +		 * below sync_bfqq->new_bfqq. Similarly if the merge
>> +		 * already happened, we need to detach from bfqq now
>> +		 * so that we cannot merge bio to a request from the
>> +		 * old cgroup.
>> +		 */
>> +		bfq_put_cooperator(sync_bfqq);
>> +		bfq_release_process_ref(bfqd, sync_bfqq);
>> +		bic_set_bfqq(bic, NULL, true, act_idx);
>> +	}
>> +}
>> +
>> /**
>>  * __bfq_bic_change_cgroup - move @bic to @bfqg.
>>  * @bfqd: the queue descriptor.
>> @@ -718,53 +759,20 @@ static void *__bfq_bic_change_cgroup(struct bfq_data *bfqd,
>> 				     struct bfq_io_cq *bic,
>> 				     struct bfq_group *bfqg)
>> {
>> -	struct bfq_queue *async_bfqq = bic_to_bfqq(bic, 0);
>> -	struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, 1);
>> -	struct bfq_entity *entity;
>> +	unsigned int act_idx;
>> 
>> -	if (async_bfqq) {
>> -		entity = &async_bfqq->entity;
>> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
>> +		struct bfq_queue *async_bfqq = bic_to_bfqq(bic, false, act_idx);
>> +		struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, true, act_idx);
>> 
>> -		if (entity->sched_data != &bfqg->sched_data) {
>> -			bic_set_bfqq(bic, NULL, 0);
>> +		if (async_bfqq &&
>> +		    async_bfqq->entity.sched_data != &bfqg->sched_data) {
>> +			bic_set_bfqq(bic, NULL, false, act_idx);
>> 			bfq_release_process_ref(bfqd, async_bfqq);
>> 		}
>> -	}
>> 
>> -	if (sync_bfqq) {
>> -		if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
>> -			/* We are the only user of this bfqq, just move it */
>> -			if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
>> -				bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
>> -		} else {
>> -			struct bfq_queue *bfqq;
>> -
>> -			/*
>> -			 * The queue was merged to a different queue. Check
>> -			 * that the merge chain still belongs to the same
>> -			 * cgroup.
>> -			 */
>> -			for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
>> -				if (bfqq->entity.sched_data !=
>> -				    &bfqg->sched_data)
>> -					break;
>> -			if (bfqq) {
>> -				/*
>> -				 * Some queue changed cgroup so the merge is
>> -				 * not valid anymore. We cannot easily just
>> -				 * cancel the merge (by clearing new_bfqq) as
>> -				 * there may be other processes using this
>> -				 * queue and holding refs to all queues below
>> -				 * sync_bfqq->new_bfqq. Similarly if the merge
>> -				 * already happened, we need to detach from
>> -				 * bfqq now so that we cannot merge bio to a
>> -				 * request from the old cgroup.
>> -				 */
>> -				bfq_put_cooperator(sync_bfqq);
>> -				bfq_release_process_ref(bfqd, sync_bfqq);
>> -				bic_set_bfqq(bic, NULL, 1);
>> -			}
>> -		}
>> +		if (sync_bfqq)
>> +			bfq_sync_bfqq_move(bfqd, sync_bfqq, bic, bfqg, act_idx);
>> 	}
>> 
>> 	return bfqg;
>> diff --git a/block/bfq-iosched.c b/block/bfq-iosched.c
>> index 7ea427817f7f..16dbf52ce74b 100644
>> --- a/block/bfq-iosched.c
>> +++ b/block/bfq-iosched.c
>> @@ -377,14 +377,21 @@ static const unsigned long bfq_late_stable_merging = 600;
>> #define RQ_BIC(rq)		((struct bfq_io_cq *)((rq)->elv.priv[0]))
>> #define RQ_BFQQ(rq)		((rq)->elv.priv[1])
>> 
>> -struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync)
>> +struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync,
>> +			      unsigned int actuator_idx)
>> {
>> -	return bic->bfqq[is_sync];
>> +	if (is_sync)
>> +		return bic->bfqq[1][actuator_idx];
>> +
>> +	return bic->bfqq[0][actuator_idx];
>> }
>> 
>> static void bfq_put_stable_ref(struct bfq_queue *bfqq);
>> 
>> -void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
>> +void bic_set_bfqq(struct bfq_io_cq *bic,
>> +		  struct bfq_queue *bfqq,
>> +		  bool is_sync,
>> +		  unsigned int actuator_idx)
>> {
>> 	/*
>> 	 * If bfqq != NULL, then a non-stable queue merge between
>> @@ -399,7 +406,10 @@ void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
>> 	 * we cancel the stable merge if
>> 	 * bic->stable_merge_bfqq == bfqq.
>> 	 */
>> -	bic->bfqq[is_sync] = bfqq;
>> +	if (is_sync)
>> +		bic->bfqq[1][actuator_idx] = bfqq;
>> +	else
>> +		bic->bfqq[0][actuator_idx] = bfqq;
>> 
>> 	if (bfqq && bic->stable_merge_bfqq == bfqq) {
>> 		/*
>> @@ -672,9 +682,9 @@ static void bfq_limit_depth(blk_opf_t opf, struct blk_mq_alloc_data *data)
>> {
>> 	struct bfq_data *bfqd = data->q->elevator->elevator_data;
>> 	struct bfq_io_cq *bic = bfq_bic_lookup(data->q);
>> -	struct bfq_queue *bfqq = bic ? bic_to_bfqq(bic, op_is_sync(opf)) : NULL;
>> 	int depth;
>> 	unsigned limit = data->q->nr_requests;
>> +	unsigned int act_idx;
>> 
>> 	/* Sync reads have full depth available */
>> 	if (op_is_sync(opf) && !op_is_write(opf)) {
>> @@ -684,14 +694,21 @@ static void bfq_limit_depth(blk_opf_t opf, struct blk_mq_alloc_data *data)
>> 		limit = (limit * depth) >> bfqd->full_depth_shift;
>> 	}
>> 
>> -	/*
>> -	 * Does queue (or any parent entity) exceed number of requests that
>> -	 * should be available to it? Heavily limit depth so that it cannot
>> -	 * consume more available requests and thus starve other entities.
>> -	 */
>> -	if (bfqq && bfqq_request_over_limit(bfqq, limit))
>> -		depth = 1;
>> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
>> +		struct bfq_queue *bfqq =
>> +			bic ? bic_to_bfqq(bic, op_is_sync(opf), act_idx) : NULL;
> 
> Commented already: why not add a "if (!bfqq) return NULL;" in
> bic_to_bfqq() ?

You have probably missed my reply on this.  The problem is that your
proposal would improve code (only) here, but it would entail the above
control for all the other invocations, for which it is useless :(

I'm sending a V11, with the above nit fixed, and with only this patch
needing finalization.

Thanks,
Paolo

> 
>> 
>> +		/*
>> +		 * Does queue (or any parent entity) exceed number of
>> +		 * requests that should be available to it? Heavily
>> +		 * limit depth so that it cannot consume more
>> +		 * available requests and thus starve other entities.
>> +		 */
>> +		if (bfqq && bfqq_request_over_limit(bfqq, limit)) {
>> +			depth = 1;
>> +			break;
>> +		}
>> +	}
>> 	bfq_log(bfqd, "[%s] wr_busy %d sync %d depth %u",
>> 		__func__, bfqd->wr_busy_queues, op_is_sync(opf), depth);
>> 	if (depth)
>> @@ -1812,6 +1829,18 @@ static bool bfq_bfqq_higher_class_or_weight(struct bfq_queue *bfqq,
>> 	return bfqq_weight > in_serv_weight;
>> }
>> 
>> +/*
>> + * Get the index of the actuator that will serve bio.
>> + */
>> +static unsigned int bfq_actuator_index(struct bfq_data *bfqd, struct bio *bio)
>> +{
>> +	/*
>> +	 * Multi-actuator support not complete yet, so always return 0
>> +	 * for the moment (to keep incomplete mechanisms off).
>> +	 */
>> +	return 0;
>> +}
>> +
>> static bool bfq_better_to_idle(struct bfq_queue *bfqq);
>> 
>> static void bfq_bfqq_handle_idle_busy_switch(struct bfq_data *bfqd,
>> @@ -2142,7 +2171,7 @@ static void bfq_check_waker(struct bfq_data *bfqd, struct bfq_queue *bfqq,
>> 	 * We reset waker detection logic also if too much time has passed
>>  	 * since the first detection. If wakeups are rare, pointless idling
>> 	 * doesn't hurt throughput that much. The condition below makes sure
>> -	 * we do not uselessly idle blocking waker in more than 1/64 cases. 
>> +	 * we do not uselessly idle blocking waker in more than 1/64 cases.
>> 	 */
>> 	if (bfqd->last_completed_rq_bfqq !=
>> 	    bfqq->tentative_waker_bfqq ||
>> @@ -2478,7 +2507,8 @@ static bool bfq_bio_merge(struct request_queue *q, struct bio *bio,
>> 		 */
>> 		bfq_bic_update_cgroup(bic, bio);
>> 
>> -		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf));
>> +		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf),
>> +					     bfq_actuator_index(bfqd, bio));
>> 	} else {
>> 		bfqd->bio_bfqq = NULL;
>> 	}
>> @@ -3174,7 +3204,7 @@ bfq_merge_bfqqs(struct bfq_data *bfqd, struct bfq_io_cq *bic,
>> 	/*
>> 	 * Merge queues (that is, let bic redirect its requests to new_bfqq)
>> 	 */
>> -	bic_set_bfqq(bic, new_bfqq, 1);
>> +	bic_set_bfqq(bic, new_bfqq, true, bfqq->actuator_idx);
>> 	bfq_mark_bfqq_coop(new_bfqq);
>> 	/*
>> 	 * new_bfqq now belongs to at least two bics (it is a shared queue):
>> @@ -4808,11 +4838,8 @@ static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
>> 	 */
>> 	if (bfq_bfqq_wait_request(bfqq) ||
>> 	    (bfqq->dispatched != 0 && bfq_better_to_idle(bfqq))) {
>> -		struct bfq_queue *async_bfqq =
>> -			bfqq->bic && bfqq->bic->bfqq[0] &&
>> -			bfq_bfqq_busy(bfqq->bic->bfqq[0]) &&
>> -			bfqq->bic->bfqq[0]->next_rq ?
>> -			bfqq->bic->bfqq[0] : NULL;
>> +		unsigned int act_idx = bfqq->actuator_idx;
>> +		struct bfq_queue *async_bfqq = NULL;
>> 		struct bfq_queue *blocked_bfqq =
>> 			!hlist_empty(&bfqq->woken_list) ?
>> 			container_of(bfqq->woken_list.first,
>> @@ -4820,6 +4847,10 @@ static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
>> 				     woken_list_node)
>> 			: NULL;
>> 
>> +		if (bfqq->bic && bfqq->bic->bfqq[0][act_idx] &&
>> +		    bfq_bfqq_busy(bfqq->bic->bfqq[0][act_idx]) &&
>> +		    bfqq->bic->bfqq[0][act_idx]->next_rq)
>> +			async_bfqq = bfqq->bic->bfqq[0][act_idx];
>> 		/*
>> 		 * The next four mutually-exclusive ifs decide
>> 		 * whether to try injection, and choose the queue to
>> @@ -4904,7 +4935,7 @@ static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
>> 		    icq_to_bic(async_bfqq->next_rq->elv.icq) == bfqq->bic &&
>> 		    bfq_serv_to_charge(async_bfqq->next_rq, async_bfqq) <=
>> 		    bfq_bfqq_budget_left(async_bfqq))
>> -			bfqq = bfqq->bic->bfqq[0];
>> +			bfqq = bfqq->bic->bfqq[0][act_idx];
>> 		else if (bfqq->waker_bfqq &&
>> 			   bfq_bfqq_busy(bfqq->waker_bfqq) &&
>> 			   bfqq->waker_bfqq->next_rq &&
>> @@ -5365,49 +5396,55 @@ static void bfq_exit_bfqq(struct bfq_data *bfqd, struct bfq_queue *bfqq)
>> 	bfq_release_process_ref(bfqd, bfqq);
>> }
>> 
>> -static void bfq_exit_icq_bfqq(struct bfq_io_cq *bic, bool is_sync)
>> +static void bfq_exit_icq_bfqq(struct bfq_io_cq *bic, bool is_sync,
>> +			      unsigned int actuator_idx)
>> {
>> -	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync);
>> +	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync, actuator_idx);
>> 	struct bfq_data *bfqd;
>> 
>> 	if (bfqq)
>> 		bfqd = bfqq->bfqd; /* NULL if scheduler already exited */
>> 
>> 	if (bfqq && bfqd) {
>> -		unsigned long flags;
>> -
>> -		spin_lock_irqsave(&bfqd->lock, flags);
>> 		bfqq->bic = NULL;
>> 		bfq_exit_bfqq(bfqd, bfqq);
>> -		bic_set_bfqq(bic, NULL, is_sync);
>> -		spin_unlock_irqrestore(&bfqd->lock, flags);
>> +		bic_set_bfqq(bic, NULL, is_sync, actuator_idx);
>> 	}
>> }
>> 
>> static void bfq_exit_icq(struct io_cq *icq)
>> {
>> 	struct bfq_io_cq *bic = icq_to_bic(icq);
>> +	struct bfq_data *bfqd = bic_to_bfqd(bic);
>> +	unsigned long flags;
>> +	unsigned int act_idx;
>> +	/*
>> +	 * If bfqd and thus bfqd->num_actuators is not available any
>> +	 * longer, then cycle over all possible per-actuator bfqqs in
>> +	 * next loop. We rely on bic being zeroed on creation, and
>> +	 * therefore on its unused per-actuator fields being NULL.
>> +	 */
>> +	unsigned int num_actuators = BFQ_MAX_ACTUATORS;
>> 
>> -	if (bic->stable_merge_bfqq) {
>> -		struct bfq_data *bfqd = bic->stable_merge_bfqq->bfqd;
>> +	/*
>> +	 * bfqd is NULL if scheduler already exited, and in that case
>> +	 * this is the last time these queues are accessed.
>> +	 */
>> +	if (bfqd) {
>> +		spin_lock_irqsave(&bfqd->lock, flags);
>> +		num_actuators = bfqd->num_actuators;
>> +	}
>> 
>> -		/*
>> -		 * bfqd is NULL if scheduler already exited, and in
>> -		 * that case this is the last time bfqq is accessed.
>> -		 */
>> -		if (bfqd) {
>> -			unsigned long flags;
>> +	if (bic->stable_merge_bfqq)
>> +		bfq_put_stable_ref(bic->stable_merge_bfqq);
>> 
>> -			spin_lock_irqsave(&bfqd->lock, flags);
>> -			bfq_put_stable_ref(bic->stable_merge_bfqq);
>> -			spin_unlock_irqrestore(&bfqd->lock, flags);
>> -		} else {
>> -			bfq_put_stable_ref(bic->stable_merge_bfqq);
>> -		}
>> +	for (act_idx = 0; act_idx < num_actuators; act_idx++) {
>> +		bfq_exit_icq_bfqq(bic, true, act_idx);
>> +		bfq_exit_icq_bfqq(bic, false, act_idx);
>> 	}
>> 
>> -	bfq_exit_icq_bfqq(bic, true);
>> -	bfq_exit_icq_bfqq(bic, false);
>> +	if (bfqd)
>> +		spin_unlock_irqrestore(&bfqd->lock, flags);
>> }
>> 
>> /*
>> @@ -5484,23 +5521,25 @@ static void bfq_check_ioprio_change(struct bfq_io_cq *bic, struct bio *bio)
>> 
>> 	bic->ioprio = ioprio;
>> 
>> -	bfqq = bic_to_bfqq(bic, false);
>> +	bfqq = bic_to_bfqq(bic, false, bfq_actuator_index(bfqd, bio));
>> 	if (bfqq) {
>> 		bfq_release_process_ref(bfqd, bfqq);
>> 		bfqq = bfq_get_queue(bfqd, bio, false, bic, true);
>> -		bic_set_bfqq(bic, bfqq, false);
>> +		bic_set_bfqq(bic, bfqq, false, bfq_actuator_index(bfqd, bio));
>> 	}
>> 
>> -	bfqq = bic_to_bfqq(bic, true);
>> +	bfqq = bic_to_bfqq(bic, true, bfq_actuator_index(bfqd, bio));
>> 	if (bfqq)
>> 		bfq_set_next_ioprio_data(bfqq, bic);
>> }
>> 
>> static void bfq_init_bfqq(struct bfq_data *bfqd, struct bfq_queue *bfqq,
>> -			  struct bfq_io_cq *bic, pid_t pid, int is_sync)
>> +			  struct bfq_io_cq *bic, pid_t pid, int is_sync,
>> +			  unsigned int act_idx)
>> {
>> 	u64 now_ns = ktime_get_ns();
>> 
>> +	bfqq->actuator_idx = act_idx;
>> 	RB_CLEAR_NODE(&bfqq->entity.rb_node);
>> 	INIT_LIST_HEAD(&bfqq->fifo);
>> 	INIT_HLIST_NODE(&bfqq->burst_list_node);
>> @@ -5753,7 +5792,7 @@ static struct bfq_queue *bfq_get_queue(struct bfq_data *bfqd,
>> 
>> 	if (bfqq) {
>> 		bfq_init_bfqq(bfqd, bfqq, bic, current->pid,
>> -			      is_sync);
>> +			      is_sync, bfq_actuator_index(bfqd, bio));
>> 		bfq_init_entity(&bfqq->entity, bfqg);
>> 		bfq_log_bfqq(bfqd, bfqq, "allocated");
>> 	} else {
>> @@ -6068,7 +6107,8 @@ static bool __bfq_insert_request(struct bfq_data *bfqd, struct request *rq)
>> 		 * then complete the merge and redirect it to
>> 		 * new_bfqq.
>> 		 */
>> -		if (bic_to_bfqq(RQ_BIC(rq), 1) == bfqq)
>> +		if (bic_to_bfqq(RQ_BIC(rq), true,
>> +				bfq_actuator_index(bfqd, rq->bio)) == bfqq)
>> 			bfq_merge_bfqqs(bfqd, RQ_BIC(rq),
>> 					bfqq, new_bfqq);
>> 
>> @@ -6622,7 +6662,7 @@ bfq_split_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq)
>> 		return bfqq;
>> 	}
>> 
>> -	bic_set_bfqq(bic, NULL, 1);
>> +	bic_set_bfqq(bic, NULL, true, bfqq->actuator_idx);
>> 
>> 	bfq_put_cooperator(bfqq);
>> 
>> @@ -6636,7 +6676,8 @@ static struct bfq_queue *bfq_get_bfqq_handle_split(struct bfq_data *bfqd,
>> 						   bool split, bool is_sync,
>> 						   bool *new_queue)
>> {
>> -	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync);
>> +	unsigned int act_idx = bfq_actuator_index(bfqd, bio);
>> +	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync, act_idx);
>> 
>> 	if (likely(bfqq && bfqq != &bfqd->oom_bfqq))
>> 		return bfqq;
>> @@ -6648,7 +6689,7 @@ static struct bfq_queue *bfq_get_bfqq_handle_split(struct bfq_data *bfqd,
>> 		bfq_put_queue(bfqq);
>> 	bfqq = bfq_get_queue(bfqd, bio, is_sync, bic, split);
>> 
>> -	bic_set_bfqq(bic, bfqq, is_sync);
>> +	bic_set_bfqq(bic, bfqq, is_sync, act_idx);
>> 	if (split && is_sync) {
>> 		if ((bic->was_in_burst_list && bfqd->large_burst) ||
>> 		    bic->saved_in_large_burst)
>> @@ -7090,8 +7131,10 @@ static int bfq_init_queue(struct request_queue *q, struct elevator_type *e)
>> 	 * Our fallback bfqq if bfq_find_alloc_queue() runs into OOM issues.
>> 	 * Grab a permanent reference to it, so that the normal code flow
>> 	 * will not attempt to free it.
>> +	 * Set zero as actuator index: we will pretend that
>> +	 * all I/O requests are for the same actuator.
>> 	 */
>> -	bfq_init_bfqq(bfqd, &bfqd->oom_bfqq, NULL, 1, 0);
>> +	bfq_init_bfqq(bfqd, &bfqd->oom_bfqq, NULL, 1, 0, 0);
>> 	bfqd->oom_bfqq.ref++;
>> 	bfqd->oom_bfqq.new_ioprio = BFQ_DEFAULT_QUEUE_IOPRIO;
>> 	bfqd->oom_bfqq.new_ioprio_class = IOPRIO_CLASS_BE;
>> @@ -7110,6 +7153,13 @@ static int bfq_init_queue(struct request_queue *q, struct elevator_type *e)
>> 
>> 	bfqd->queue = q;
>> 
>> +	/*
>> +	 * Multi-actuator support not complete yet, unconditionally
>> +	 * set to only one actuator for the moment (to keep incomplete
>> +	 * mechanisms off).
>> +	 */
>> +	bfqd->num_actuators = 1;
>> +
>> 	INIT_LIST_HEAD(&bfqd->dispatch);
>> 
>> 	hrtimer_init(&bfqd->idle_slice_timer, CLOCK_MONOTONIC,
>> diff --git a/block/bfq-iosched.h b/block/bfq-iosched.h
>> index 71f721670ab6..2b413ddffbb9 100644
>> --- a/block/bfq-iosched.h
>> +++ b/block/bfq-iosched.h
>> @@ -33,6 +33,14 @@
>>  */
>> #define BFQ_SOFTRT_WEIGHT_FACTOR	100
>> 
>> +/*
>> + * Maximum number of actuators supported. This constant is used simply
>> + * to define the size of the static array that will contain
>> + * per-actuator data. The current value is hopefully a good upper
>> + * bound to the possible number of actuators of any actual drive.
>> + */
>> +#define BFQ_MAX_ACTUATORS 8
>> +
>> struct bfq_entity;
>> 
>> /**
>> @@ -225,12 +233,14 @@ struct bfq_ttime {
>>  * struct bfq_queue - leaf schedulable entity.
>>  *
>>  * A bfq_queue is a leaf request queue; it can be associated with an
>> - * io_context or more, if it  is  async or shared  between  cooperating
>> - * processes. @cgroup holds a reference to the cgroup, to be sure that it
>> - * does not disappear while a bfqq still references it (mostly to avoid
>> - * races between request issuing and task migration followed by cgroup
>> - * destruction).
>> - * All the fields are protected by the queue lock of the containing bfqd.
>> + * io_context or more, if it is async or shared between cooperating
>> + * processes. Besides, it contains I/O requests for only one actuator
>> + * (an io_context is associated with a different bfq_queue for each
>> + * actuator it generates I/O for). @cgroup holds a reference to the
>> + * cgroup, to be sure that it does not disappear while a bfqq still
>> + * references it (mostly to avoid races between request issuing and
>> + * task migration followed by cgroup destruction).  All the fields are
>> + * protected by the queue lock of the containing bfqd.
>>  */
>> struct bfq_queue {
>> 	/* reference counter */
>> @@ -395,6 +405,9 @@ struct bfq_queue {
>> 	 * the woken queues when this queue exits.
>> 	 */
>> 	struct hlist_head woken_list;
>> +
>> +	/* index of the actuator this queue is associated with */
>> +	unsigned int actuator_idx;
>> };
>> 
>> /**
>> @@ -403,8 +416,17 @@ struct bfq_queue {
>> struct bfq_io_cq {
>> 	/* associated io_cq structure */
>> 	struct io_cq icq; /* must be the first member */
>> -	/* array of two process queues, the sync and the async */
>> -	struct bfq_queue *bfqq[2];
>> +	/*
>> +	 * Matrix of associated process queues: first row for async
>> +	 * queues, second row sync queues. Each row contains one
>> +	 * column for each actuator. An I/O request generated by the
>> +	 * process is inserted into the queue pointed by bfqq[i][j] if
>> +	 * the request is to be served by the j-th actuator of the
>> +	 * drive, where i==0 or i==1, depending on whether the request
>> +	 * is async or sync. So there is a distinct queue for each
>> +	 * actuator.
>> +	 */
>> +	struct bfq_queue *bfqq[2][BFQ_MAX_ACTUATORS];
>> 	/* per (request_queue, blkcg) ioprio */
>> 	int ioprio;
>> #ifdef CONFIG_BFQ_GROUP_IOSCHED
>> @@ -768,6 +790,13 @@ struct bfq_data {
>> 	 */
>> 	unsigned int word_depths[2][2];
>> 	unsigned int full_depth_shift;
>> +
>> +	/*
>> +	 * Number of independent actuators. This is equal to 1 in
>> +	 * case of single-actuator drives.
>> +	 */
>> +	unsigned int num_actuators;
>> +
>> };
>> 
>> enum bfqq_state_flags {
>> @@ -964,8 +993,10 @@ struct bfq_group {
>> 
>> extern const int bfq_timeout;
>> 
>> -struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync);
>> -void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync);
>> +struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync,
>> +				unsigned int actuator_idx);
>> +void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync,
>> +				unsigned int actuator_idx);
>> struct bfq_data *bic_to_bfqd(struct bfq_io_cq *bic);
>> void bfq_pos_tree_add_move(struct bfq_data *bfqd, struct bfq_queue *bfqq);
>> void bfq_weights_tree_add(struct bfq_data *bfqd, struct bfq_queue *bfqq,
> 
> -- 
> Damien Le Moal
> Western Digital Research
Damien Le Moal Dec. 21, 2022, 12:50 a.m. UTC | #3
On 2022/12/20 22:10, Paolo Valente wrote:
>>> -	/*
>>> -	 * Does queue (or any parent entity) exceed number of requests that
>>> -	 * should be available to it? Heavily limit depth so that it cannot
>>> -	 * consume more available requests and thus starve other entities.
>>> -	 */
>>> -	if (bfqq && bfqq_request_over_limit(bfqq, limit))
>>> -		depth = 1;
>>> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
>>> +		struct bfq_queue *bfqq =
>>> +			bic ? bic_to_bfqq(bic, op_is_sync(opf), act_idx) : NULL;
>>
>> Commented already: why not add a "if (!bfqq) return NULL;" in
>> bic_to_bfqq() ?
> 
> You have probably missed my reply on this.  The problem is that your
> proposal would improve code (only) here, but it would entail the above
> control for all the other invocations, for which it is useless :(

But then you have *a lot* of "if (bfqd)" tests that are useless elsewhere since
bic_to_bfqq() never returns NULL.

And for this line, I personally would prefer seeing something like:

		struct bfq_queue *bfqq;


		if (bic)
			bfqd = bic_to_bfqq(bic, op_is_sync(opf), act_idx)
		else
			bfqd = NULL;

Which is a lot simpler to read.
Paolo Valente Dec. 21, 2022, 10:13 a.m. UTC | #4
> Il giorno 21 dic 2022, alle ore 01:50, Damien Le Moal <damien.lemoal@opensource.wdc.com> ha scritto:
> 
> On 2022/12/20 22:10, Paolo Valente wrote:
>>>> -	/*
>>>> -	 * Does queue (or any parent entity) exceed number of requests that
>>>> -	 * should be available to it? Heavily limit depth so that it cannot
>>>> -	 * consume more available requests and thus starve other entities.
>>>> -	 */
>>>> -	if (bfqq && bfqq_request_over_limit(bfqq, limit))
>>>> -		depth = 1;
>>>> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
>>>> +		struct bfq_queue *bfqq =
>>>> +			bic ? bic_to_bfqq(bic, op_is_sync(opf), act_idx) : NULL;
>>> 
>>> Commented already: why not add a "if (!bfqq) return NULL;" in
>>> bic_to_bfqq() ?
>> 
>> You have probably missed my reply on this.  The problem is that your
>> proposal would improve code (only) here, but it would entail the above
>> control for all the other invocations, for which it is useless :(
> 
> But then you have *a lot* of "if (bfqd)" tests that are useless elsewhere since
> bic_to_bfqq() never returns NULL.
> 

I'm probably misunderstanding your point, sorry.  Could you point me
to one of the places where there is the useless control that would go
away if we add your proposed control inside bic_to_bfqq?  (of course
apart form the above one, which seems to be the only one to me)

> And for this line, I personally would prefer seeing something like:
> 
> 		struct bfq_queue *bfqq;
> 
> 
> 		if (bic)
> 			bfqd = bic_to_bfqq(bic, op_is_sync(opf), act_idx)
> 		else
> 			bfqd = NULL;
> 
> Which is a lot simpler to read.
> 
> 

Ok, as I have your blessing on this point, I'll send a V12 with also
this change.

Thanks,
Paolo

> -- 
> Damien Le Moal
> Western Digital Research
>
Paolo Valente Dec. 21, 2022, 10:30 a.m. UTC | #5
> Il giorno 21 dic 2022, alle ore 11:13, Paolo Valente <paolo.valente@linaro.org> ha scritto:
> 
> 
> 
>> Il giorno 21 dic 2022, alle ore 01:50, Damien Le Moal <damien.lemoal@opensource.wdc.com> ha scritto:
>> 
>> On 2022/12/20 22:10, Paolo Valente wrote:
>>>>> -	/*
>>>>> -	 * Does queue (or any parent entity) exceed number of requests that
>>>>> -	 * should be available to it? Heavily limit depth so that it cannot
>>>>> -	 * consume more available requests and thus starve other entities.
>>>>> -	 */
>>>>> -	if (bfqq && bfqq_request_over_limit(bfqq, limit))
>>>>> -		depth = 1;
>>>>> +	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
>>>>> +		struct bfq_queue *bfqq =
>>>>> +			bic ? bic_to_bfqq(bic, op_is_sync(opf), act_idx) : NULL;
>>>> 
>>>> Commented already: why not add a "if (!bfqq) return NULL;" in
>>>> bic_to_bfqq() ?
>>> 
>>> You have probably missed my reply on this.  The problem is that your
>>> proposal would improve code (only) here, but it would entail the above
>>> control for all the other invocations, for which it is useless :(
>> 
>> But then you have *a lot* of "if (bfqd)" tests that are useless elsewhere since
>> bic_to_bfqq() never returns NULL.
>> 
> 
> I'm probably misunderstanding your point, sorry.  Could you point me
> to one of the places where there is the useless control that would go
> away if we add your proposed control inside bic_to_bfqq?

You had already done that in a following email, sorry.  I have replied
to that email of yours.

Thanks,
Paolo
diff mbox series

Patch

diff --git a/block/bfq-cgroup.c b/block/bfq-cgroup.c
index 7d624a3a3f0f..7ea77f994424 100644
--- a/block/bfq-cgroup.c
+++ b/block/bfq-cgroup.c
@@ -704,6 +704,47 @@  void bfq_bfqq_move(struct bfq_data *bfqd, struct bfq_queue *bfqq,
 	bfq_put_queue(bfqq);
 }
 
+static void bfq_sync_bfqq_move(struct bfq_data *bfqd,
+			       struct bfq_queue *sync_bfqq,
+			       struct bfq_io_cq *bic,
+			       struct bfq_group *bfqg,
+			       unsigned int act_idx)
+{
+	struct bfq_queue *bfqq;
+
+	if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
+		/* We are the only user of this bfqq, just move it */
+		if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
+			bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
+		return;
+	}
+
+	/*
+	 * The queue was merged to a different queue. Check
+	 * that the merge chain still belongs to the same
+	 * cgroup.
+	 */
+	for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
+		if (bfqq->entity.sched_data !=
+		    &bfqg->sched_data)
+			break;
+	if (bfqq) {
+		/*
+		 * Some queue changed cgroup so the merge is not valid
+		 * anymore. We cannot easily just cancel the merge (by
+		 * clearing new_bfqq) as there may be other processes
+		 * using this queue and holding refs to all queues
+		 * below sync_bfqq->new_bfqq. Similarly if the merge
+		 * already happened, we need to detach from bfqq now
+		 * so that we cannot merge bio to a request from the
+		 * old cgroup.
+		 */
+		bfq_put_cooperator(sync_bfqq);
+		bfq_release_process_ref(bfqd, sync_bfqq);
+		bic_set_bfqq(bic, NULL, true, act_idx);
+	}
+}
+
 /**
  * __bfq_bic_change_cgroup - move @bic to @bfqg.
  * @bfqd: the queue descriptor.
@@ -718,53 +759,20 @@  static void *__bfq_bic_change_cgroup(struct bfq_data *bfqd,
 				     struct bfq_io_cq *bic,
 				     struct bfq_group *bfqg)
 {
-	struct bfq_queue *async_bfqq = bic_to_bfqq(bic, 0);
-	struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, 1);
-	struct bfq_entity *entity;
+	unsigned int act_idx;
 
-	if (async_bfqq) {
-		entity = &async_bfqq->entity;
+	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
+		struct bfq_queue *async_bfqq = bic_to_bfqq(bic, false, act_idx);
+		struct bfq_queue *sync_bfqq = bic_to_bfqq(bic, true, act_idx);
 
-		if (entity->sched_data != &bfqg->sched_data) {
-			bic_set_bfqq(bic, NULL, 0);
+		if (async_bfqq &&
+		    async_bfqq->entity.sched_data != &bfqg->sched_data) {
+			bic_set_bfqq(bic, NULL, false, act_idx);
 			bfq_release_process_ref(bfqd, async_bfqq);
 		}
-	}
 
-	if (sync_bfqq) {
-		if (!sync_bfqq->new_bfqq && !bfq_bfqq_coop(sync_bfqq)) {
-			/* We are the only user of this bfqq, just move it */
-			if (sync_bfqq->entity.sched_data != &bfqg->sched_data)
-				bfq_bfqq_move(bfqd, sync_bfqq, bfqg);
-		} else {
-			struct bfq_queue *bfqq;
-
-			/*
-			 * The queue was merged to a different queue. Check
-			 * that the merge chain still belongs to the same
-			 * cgroup.
-			 */
-			for (bfqq = sync_bfqq; bfqq; bfqq = bfqq->new_bfqq)
-				if (bfqq->entity.sched_data !=
-				    &bfqg->sched_data)
-					break;
-			if (bfqq) {
-				/*
-				 * Some queue changed cgroup so the merge is
-				 * not valid anymore. We cannot easily just
-				 * cancel the merge (by clearing new_bfqq) as
-				 * there may be other processes using this
-				 * queue and holding refs to all queues below
-				 * sync_bfqq->new_bfqq. Similarly if the merge
-				 * already happened, we need to detach from
-				 * bfqq now so that we cannot merge bio to a
-				 * request from the old cgroup.
-				 */
-				bfq_put_cooperator(sync_bfqq);
-				bfq_release_process_ref(bfqd, sync_bfqq);
-				bic_set_bfqq(bic, NULL, 1);
-			}
-		}
+		if (sync_bfqq)
+			bfq_sync_bfqq_move(bfqd, sync_bfqq, bic, bfqg, act_idx);
 	}
 
 	return bfqg;
diff --git a/block/bfq-iosched.c b/block/bfq-iosched.c
index 7ea427817f7f..16dbf52ce74b 100644
--- a/block/bfq-iosched.c
+++ b/block/bfq-iosched.c
@@ -377,14 +377,21 @@  static const unsigned long bfq_late_stable_merging = 600;
 #define RQ_BIC(rq)		((struct bfq_io_cq *)((rq)->elv.priv[0]))
 #define RQ_BFQQ(rq)		((rq)->elv.priv[1])
 
-struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync)
+struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync,
+			      unsigned int actuator_idx)
 {
-	return bic->bfqq[is_sync];
+	if (is_sync)
+		return bic->bfqq[1][actuator_idx];
+
+	return bic->bfqq[0][actuator_idx];
 }
 
 static void bfq_put_stable_ref(struct bfq_queue *bfqq);
 
-void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
+void bic_set_bfqq(struct bfq_io_cq *bic,
+		  struct bfq_queue *bfqq,
+		  bool is_sync,
+		  unsigned int actuator_idx)
 {
 	/*
 	 * If bfqq != NULL, then a non-stable queue merge between
@@ -399,7 +406,10 @@  void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync)
 	 * we cancel the stable merge if
 	 * bic->stable_merge_bfqq == bfqq.
 	 */
-	bic->bfqq[is_sync] = bfqq;
+	if (is_sync)
+		bic->bfqq[1][actuator_idx] = bfqq;
+	else
+		bic->bfqq[0][actuator_idx] = bfqq;
 
 	if (bfqq && bic->stable_merge_bfqq == bfqq) {
 		/*
@@ -672,9 +682,9 @@  static void bfq_limit_depth(blk_opf_t opf, struct blk_mq_alloc_data *data)
 {
 	struct bfq_data *bfqd = data->q->elevator->elevator_data;
 	struct bfq_io_cq *bic = bfq_bic_lookup(data->q);
-	struct bfq_queue *bfqq = bic ? bic_to_bfqq(bic, op_is_sync(opf)) : NULL;
 	int depth;
 	unsigned limit = data->q->nr_requests;
+	unsigned int act_idx;
 
 	/* Sync reads have full depth available */
 	if (op_is_sync(opf) && !op_is_write(opf)) {
@@ -684,14 +694,21 @@  static void bfq_limit_depth(blk_opf_t opf, struct blk_mq_alloc_data *data)
 		limit = (limit * depth) >> bfqd->full_depth_shift;
 	}
 
-	/*
-	 * Does queue (or any parent entity) exceed number of requests that
-	 * should be available to it? Heavily limit depth so that it cannot
-	 * consume more available requests and thus starve other entities.
-	 */
-	if (bfqq && bfqq_request_over_limit(bfqq, limit))
-		depth = 1;
+	for (act_idx = 0; act_idx < bfqd->num_actuators; act_idx++) {
+		struct bfq_queue *bfqq =
+			bic ? bic_to_bfqq(bic, op_is_sync(opf), act_idx) : NULL;
 
+		/*
+		 * Does queue (or any parent entity) exceed number of
+		 * requests that should be available to it? Heavily
+		 * limit depth so that it cannot consume more
+		 * available requests and thus starve other entities.
+		 */
+		if (bfqq && bfqq_request_over_limit(bfqq, limit)) {
+			depth = 1;
+			break;
+		}
+	}
 	bfq_log(bfqd, "[%s] wr_busy %d sync %d depth %u",
 		__func__, bfqd->wr_busy_queues, op_is_sync(opf), depth);
 	if (depth)
@@ -1812,6 +1829,18 @@  static bool bfq_bfqq_higher_class_or_weight(struct bfq_queue *bfqq,
 	return bfqq_weight > in_serv_weight;
 }
 
+/*
+ * Get the index of the actuator that will serve bio.
+ */
+static unsigned int bfq_actuator_index(struct bfq_data *bfqd, struct bio *bio)
+{
+	/*
+	 * Multi-actuator support not complete yet, so always return 0
+	 * for the moment (to keep incomplete mechanisms off).
+	 */
+	return 0;
+}
+
 static bool bfq_better_to_idle(struct bfq_queue *bfqq);
 
 static void bfq_bfqq_handle_idle_busy_switch(struct bfq_data *bfqd,
@@ -2142,7 +2171,7 @@  static void bfq_check_waker(struct bfq_data *bfqd, struct bfq_queue *bfqq,
 	 * We reset waker detection logic also if too much time has passed
  	 * since the first detection. If wakeups are rare, pointless idling
 	 * doesn't hurt throughput that much. The condition below makes sure
-	 * we do not uselessly idle blocking waker in more than 1/64 cases. 
+	 * we do not uselessly idle blocking waker in more than 1/64 cases.
 	 */
 	if (bfqd->last_completed_rq_bfqq !=
 	    bfqq->tentative_waker_bfqq ||
@@ -2478,7 +2507,8 @@  static bool bfq_bio_merge(struct request_queue *q, struct bio *bio,
 		 */
 		bfq_bic_update_cgroup(bic, bio);
 
-		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf));
+		bfqd->bio_bfqq = bic_to_bfqq(bic, op_is_sync(bio->bi_opf),
+					     bfq_actuator_index(bfqd, bio));
 	} else {
 		bfqd->bio_bfqq = NULL;
 	}
@@ -3174,7 +3204,7 @@  bfq_merge_bfqqs(struct bfq_data *bfqd, struct bfq_io_cq *bic,
 	/*
 	 * Merge queues (that is, let bic redirect its requests to new_bfqq)
 	 */
-	bic_set_bfqq(bic, new_bfqq, 1);
+	bic_set_bfqq(bic, new_bfqq, true, bfqq->actuator_idx);
 	bfq_mark_bfqq_coop(new_bfqq);
 	/*
 	 * new_bfqq now belongs to at least two bics (it is a shared queue):
@@ -4808,11 +4838,8 @@  static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
 	 */
 	if (bfq_bfqq_wait_request(bfqq) ||
 	    (bfqq->dispatched != 0 && bfq_better_to_idle(bfqq))) {
-		struct bfq_queue *async_bfqq =
-			bfqq->bic && bfqq->bic->bfqq[0] &&
-			bfq_bfqq_busy(bfqq->bic->bfqq[0]) &&
-			bfqq->bic->bfqq[0]->next_rq ?
-			bfqq->bic->bfqq[0] : NULL;
+		unsigned int act_idx = bfqq->actuator_idx;
+		struct bfq_queue *async_bfqq = NULL;
 		struct bfq_queue *blocked_bfqq =
 			!hlist_empty(&bfqq->woken_list) ?
 			container_of(bfqq->woken_list.first,
@@ -4820,6 +4847,10 @@  static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
 				     woken_list_node)
 			: NULL;
 
+		if (bfqq->bic && bfqq->bic->bfqq[0][act_idx] &&
+		    bfq_bfqq_busy(bfqq->bic->bfqq[0][act_idx]) &&
+		    bfqq->bic->bfqq[0][act_idx]->next_rq)
+			async_bfqq = bfqq->bic->bfqq[0][act_idx];
 		/*
 		 * The next four mutually-exclusive ifs decide
 		 * whether to try injection, and choose the queue to
@@ -4904,7 +4935,7 @@  static struct bfq_queue *bfq_select_queue(struct bfq_data *bfqd)
 		    icq_to_bic(async_bfqq->next_rq->elv.icq) == bfqq->bic &&
 		    bfq_serv_to_charge(async_bfqq->next_rq, async_bfqq) <=
 		    bfq_bfqq_budget_left(async_bfqq))
-			bfqq = bfqq->bic->bfqq[0];
+			bfqq = bfqq->bic->bfqq[0][act_idx];
 		else if (bfqq->waker_bfqq &&
 			   bfq_bfqq_busy(bfqq->waker_bfqq) &&
 			   bfqq->waker_bfqq->next_rq &&
@@ -5365,49 +5396,55 @@  static void bfq_exit_bfqq(struct bfq_data *bfqd, struct bfq_queue *bfqq)
 	bfq_release_process_ref(bfqd, bfqq);
 }
 
-static void bfq_exit_icq_bfqq(struct bfq_io_cq *bic, bool is_sync)
+static void bfq_exit_icq_bfqq(struct bfq_io_cq *bic, bool is_sync,
+			      unsigned int actuator_idx)
 {
-	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync);
+	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync, actuator_idx);
 	struct bfq_data *bfqd;
 
 	if (bfqq)
 		bfqd = bfqq->bfqd; /* NULL if scheduler already exited */
 
 	if (bfqq && bfqd) {
-		unsigned long flags;
-
-		spin_lock_irqsave(&bfqd->lock, flags);
 		bfqq->bic = NULL;
 		bfq_exit_bfqq(bfqd, bfqq);
-		bic_set_bfqq(bic, NULL, is_sync);
-		spin_unlock_irqrestore(&bfqd->lock, flags);
+		bic_set_bfqq(bic, NULL, is_sync, actuator_idx);
 	}
 }
 
 static void bfq_exit_icq(struct io_cq *icq)
 {
 	struct bfq_io_cq *bic = icq_to_bic(icq);
+	struct bfq_data *bfqd = bic_to_bfqd(bic);
+	unsigned long flags;
+	unsigned int act_idx;
+	/*
+	 * If bfqd and thus bfqd->num_actuators is not available any
+	 * longer, then cycle over all possible per-actuator bfqqs in
+	 * next loop. We rely on bic being zeroed on creation, and
+	 * therefore on its unused per-actuator fields being NULL.
+	 */
+	unsigned int num_actuators = BFQ_MAX_ACTUATORS;
 
-	if (bic->stable_merge_bfqq) {
-		struct bfq_data *bfqd = bic->stable_merge_bfqq->bfqd;
+	/*
+	 * bfqd is NULL if scheduler already exited, and in that case
+	 * this is the last time these queues are accessed.
+	 */
+	if (bfqd) {
+		spin_lock_irqsave(&bfqd->lock, flags);
+		num_actuators = bfqd->num_actuators;
+	}
 
-		/*
-		 * bfqd is NULL if scheduler already exited, and in
-		 * that case this is the last time bfqq is accessed.
-		 */
-		if (bfqd) {
-			unsigned long flags;
+	if (bic->stable_merge_bfqq)
+		bfq_put_stable_ref(bic->stable_merge_bfqq);
 
-			spin_lock_irqsave(&bfqd->lock, flags);
-			bfq_put_stable_ref(bic->stable_merge_bfqq);
-			spin_unlock_irqrestore(&bfqd->lock, flags);
-		} else {
-			bfq_put_stable_ref(bic->stable_merge_bfqq);
-		}
+	for (act_idx = 0; act_idx < num_actuators; act_idx++) {
+		bfq_exit_icq_bfqq(bic, true, act_idx);
+		bfq_exit_icq_bfqq(bic, false, act_idx);
 	}
 
-	bfq_exit_icq_bfqq(bic, true);
-	bfq_exit_icq_bfqq(bic, false);
+	if (bfqd)
+		spin_unlock_irqrestore(&bfqd->lock, flags);
 }
 
 /*
@@ -5484,23 +5521,25 @@  static void bfq_check_ioprio_change(struct bfq_io_cq *bic, struct bio *bio)
 
 	bic->ioprio = ioprio;
 
-	bfqq = bic_to_bfqq(bic, false);
+	bfqq = bic_to_bfqq(bic, false, bfq_actuator_index(bfqd, bio));
 	if (bfqq) {
 		bfq_release_process_ref(bfqd, bfqq);
 		bfqq = bfq_get_queue(bfqd, bio, false, bic, true);
-		bic_set_bfqq(bic, bfqq, false);
+		bic_set_bfqq(bic, bfqq, false, bfq_actuator_index(bfqd, bio));
 	}
 
-	bfqq = bic_to_bfqq(bic, true);
+	bfqq = bic_to_bfqq(bic, true, bfq_actuator_index(bfqd, bio));
 	if (bfqq)
 		bfq_set_next_ioprio_data(bfqq, bic);
 }
 
 static void bfq_init_bfqq(struct bfq_data *bfqd, struct bfq_queue *bfqq,
-			  struct bfq_io_cq *bic, pid_t pid, int is_sync)
+			  struct bfq_io_cq *bic, pid_t pid, int is_sync,
+			  unsigned int act_idx)
 {
 	u64 now_ns = ktime_get_ns();
 
+	bfqq->actuator_idx = act_idx;
 	RB_CLEAR_NODE(&bfqq->entity.rb_node);
 	INIT_LIST_HEAD(&bfqq->fifo);
 	INIT_HLIST_NODE(&bfqq->burst_list_node);
@@ -5753,7 +5792,7 @@  static struct bfq_queue *bfq_get_queue(struct bfq_data *bfqd,
 
 	if (bfqq) {
 		bfq_init_bfqq(bfqd, bfqq, bic, current->pid,
-			      is_sync);
+			      is_sync, bfq_actuator_index(bfqd, bio));
 		bfq_init_entity(&bfqq->entity, bfqg);
 		bfq_log_bfqq(bfqd, bfqq, "allocated");
 	} else {
@@ -6068,7 +6107,8 @@  static bool __bfq_insert_request(struct bfq_data *bfqd, struct request *rq)
 		 * then complete the merge and redirect it to
 		 * new_bfqq.
 		 */
-		if (bic_to_bfqq(RQ_BIC(rq), 1) == bfqq)
+		if (bic_to_bfqq(RQ_BIC(rq), true,
+				bfq_actuator_index(bfqd, rq->bio)) == bfqq)
 			bfq_merge_bfqqs(bfqd, RQ_BIC(rq),
 					bfqq, new_bfqq);
 
@@ -6622,7 +6662,7 @@  bfq_split_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq)
 		return bfqq;
 	}
 
-	bic_set_bfqq(bic, NULL, 1);
+	bic_set_bfqq(bic, NULL, true, bfqq->actuator_idx);
 
 	bfq_put_cooperator(bfqq);
 
@@ -6636,7 +6676,8 @@  static struct bfq_queue *bfq_get_bfqq_handle_split(struct bfq_data *bfqd,
 						   bool split, bool is_sync,
 						   bool *new_queue)
 {
-	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync);
+	unsigned int act_idx = bfq_actuator_index(bfqd, bio);
+	struct bfq_queue *bfqq = bic_to_bfqq(bic, is_sync, act_idx);
 
 	if (likely(bfqq && bfqq != &bfqd->oom_bfqq))
 		return bfqq;
@@ -6648,7 +6689,7 @@  static struct bfq_queue *bfq_get_bfqq_handle_split(struct bfq_data *bfqd,
 		bfq_put_queue(bfqq);
 	bfqq = bfq_get_queue(bfqd, bio, is_sync, bic, split);
 
-	bic_set_bfqq(bic, bfqq, is_sync);
+	bic_set_bfqq(bic, bfqq, is_sync, act_idx);
 	if (split && is_sync) {
 		if ((bic->was_in_burst_list && bfqd->large_burst) ||
 		    bic->saved_in_large_burst)
@@ -7090,8 +7131,10 @@  static int bfq_init_queue(struct request_queue *q, struct elevator_type *e)
 	 * Our fallback bfqq if bfq_find_alloc_queue() runs into OOM issues.
 	 * Grab a permanent reference to it, so that the normal code flow
 	 * will not attempt to free it.
+	 * Set zero as actuator index: we will pretend that
+	 * all I/O requests are for the same actuator.
 	 */
-	bfq_init_bfqq(bfqd, &bfqd->oom_bfqq, NULL, 1, 0);
+	bfq_init_bfqq(bfqd, &bfqd->oom_bfqq, NULL, 1, 0, 0);
 	bfqd->oom_bfqq.ref++;
 	bfqd->oom_bfqq.new_ioprio = BFQ_DEFAULT_QUEUE_IOPRIO;
 	bfqd->oom_bfqq.new_ioprio_class = IOPRIO_CLASS_BE;
@@ -7110,6 +7153,13 @@  static int bfq_init_queue(struct request_queue *q, struct elevator_type *e)
 
 	bfqd->queue = q;
 
+	/*
+	 * Multi-actuator support not complete yet, unconditionally
+	 * set to only one actuator for the moment (to keep incomplete
+	 * mechanisms off).
+	 */
+	bfqd->num_actuators = 1;
+
 	INIT_LIST_HEAD(&bfqd->dispatch);
 
 	hrtimer_init(&bfqd->idle_slice_timer, CLOCK_MONOTONIC,
diff --git a/block/bfq-iosched.h b/block/bfq-iosched.h
index 71f721670ab6..2b413ddffbb9 100644
--- a/block/bfq-iosched.h
+++ b/block/bfq-iosched.h
@@ -33,6 +33,14 @@ 
  */
 #define BFQ_SOFTRT_WEIGHT_FACTOR	100
 
+/*
+ * Maximum number of actuators supported. This constant is used simply
+ * to define the size of the static array that will contain
+ * per-actuator data. The current value is hopefully a good upper
+ * bound to the possible number of actuators of any actual drive.
+ */
+#define BFQ_MAX_ACTUATORS 8
+
 struct bfq_entity;
 
 /**
@@ -225,12 +233,14 @@  struct bfq_ttime {
  * struct bfq_queue - leaf schedulable entity.
  *
  * A bfq_queue is a leaf request queue; it can be associated with an
- * io_context or more, if it  is  async or shared  between  cooperating
- * processes. @cgroup holds a reference to the cgroup, to be sure that it
- * does not disappear while a bfqq still references it (mostly to avoid
- * races between request issuing and task migration followed by cgroup
- * destruction).
- * All the fields are protected by the queue lock of the containing bfqd.
+ * io_context or more, if it is async or shared between cooperating
+ * processes. Besides, it contains I/O requests for only one actuator
+ * (an io_context is associated with a different bfq_queue for each
+ * actuator it generates I/O for). @cgroup holds a reference to the
+ * cgroup, to be sure that it does not disappear while a bfqq still
+ * references it (mostly to avoid races between request issuing and
+ * task migration followed by cgroup destruction).  All the fields are
+ * protected by the queue lock of the containing bfqd.
  */
 struct bfq_queue {
 	/* reference counter */
@@ -395,6 +405,9 @@  struct bfq_queue {
 	 * the woken queues when this queue exits.
 	 */
 	struct hlist_head woken_list;
+
+	/* index of the actuator this queue is associated with */
+	unsigned int actuator_idx;
 };
 
 /**
@@ -403,8 +416,17 @@  struct bfq_queue {
 struct bfq_io_cq {
 	/* associated io_cq structure */
 	struct io_cq icq; /* must be the first member */
-	/* array of two process queues, the sync and the async */
-	struct bfq_queue *bfqq[2];
+	/*
+	 * Matrix of associated process queues: first row for async
+	 * queues, second row sync queues. Each row contains one
+	 * column for each actuator. An I/O request generated by the
+	 * process is inserted into the queue pointed by bfqq[i][j] if
+	 * the request is to be served by the j-th actuator of the
+	 * drive, where i==0 or i==1, depending on whether the request
+	 * is async or sync. So there is a distinct queue for each
+	 * actuator.
+	 */
+	struct bfq_queue *bfqq[2][BFQ_MAX_ACTUATORS];
 	/* per (request_queue, blkcg) ioprio */
 	int ioprio;
 #ifdef CONFIG_BFQ_GROUP_IOSCHED
@@ -768,6 +790,13 @@  struct bfq_data {
 	 */
 	unsigned int word_depths[2][2];
 	unsigned int full_depth_shift;
+
+	/*
+	 * Number of independent actuators. This is equal to 1 in
+	 * case of single-actuator drives.
+	 */
+	unsigned int num_actuators;
+
 };
 
 enum bfqq_state_flags {
@@ -964,8 +993,10 @@  struct bfq_group {
 
 extern const int bfq_timeout;
 
-struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync);
-void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync);
+struct bfq_queue *bic_to_bfqq(struct bfq_io_cq *bic, bool is_sync,
+				unsigned int actuator_idx);
+void bic_set_bfqq(struct bfq_io_cq *bic, struct bfq_queue *bfqq, bool is_sync,
+				unsigned int actuator_idx);
 struct bfq_data *bic_to_bfqd(struct bfq_io_cq *bic);
 void bfq_pos_tree_add_move(struct bfq_data *bfqd, struct bfq_queue *bfqq);
 void bfq_weights_tree_add(struct bfq_data *bfqd, struct bfq_queue *bfqq,