new file mode 100755
@@ -0,0 +1,156 @@
+#! /bin/bash
+# SPDX-License-Identifier: GPL-2.0
+# Copyright (C) 2021 Facebook, Inc. All Rights Reserved.
+#
+# FS QA Test 291
+#
+# Test btrfs consistency after each FUA while enabling verity on a file
+# This test works by following the pattern in log-writes/replay-individual.sh:
+# 1. run a workload (verity + sync) while logging to the log device
+# 2. replay an entry to the replay device
+# 3. snapshot the replay device to the snapshot device
+# 4. run destructive tests on the snapshot device (e.g. mount with orphans)
+# 5. goto 2
+#
+seq=`basename $0`
+seqres=$RESULT_DIR/$seq
+echo "QA output created by $seq"
+
+here=`pwd`
+tmp=/tmp/$$
+status=1 # failure is the default!
+trap "_cleanup; exit \$status" 0 1 2 3 15
+
+_cleanup()
+{
+ cd /
+ _log_writes_cleanup &> /dev/null
+ rm -f $tmp.*
+ $LVM_PROG vgremove -f -y $vgname >>$seqres.full 2>&1
+ losetup -d $loop_dev >>$seqres.full 2>&1
+}
+
+# get standard environment, filters and checks
+. ./common/rc
+. ./common/filter
+. ./common/attr
+. ./common/dmlogwrites
+. ./common/verity
+
+# remove previous $seqres.full before test
+rm -f $seqres.full
+
+# real QA test starts here
+
+_supported_fs btrfs
+
+_require_scratch
+_require_log_writes
+_require_dm_target snapshot
+_require_command $LVM_PROG lvm
+_require_scratch_verity
+
+sync_loop() {
+ i=$1
+ [ -z "$i" ] && _fail "sync loop needs a number of iterations"
+ while [ $i -gt 0 ]
+ do
+ $XFS_IO_PROG -c sync $SCRATCH_MNT
+ let i-=1
+ done
+}
+
+dump_tree() {
+ dev=$1
+ $BTRFS_UTIL_PROG inspect-internal dump-tree $dev
+}
+
+count_item() {
+ dev=$1
+ item=$2
+ dump_tree $dev | grep -c $item
+}
+
+_log_writes_init $SCRATCH_DEV
+_log_writes_mkfs
+_log_writes_mount
+
+f=$SCRATCH_MNT/fsv
+dd if=/dev/zero of=$f bs=1M count=10 >>$seqres.full 2>&1
+$XFS_IO_PROG -c sync $SCRATCH_MNT
+sync_loop 10 &
+_fsv_enable $f
+$XFS_IO_PROG -c sync $SCRATCH_MNT
+
+_log_writes_unmount
+_log_writes_remove
+
+dd if=/dev/zero of=$tmp.loop-file bs=1M count=1 seek=8192 >>$seqres.full 2>&1
+loop_dev=$(losetup -f --show $tmp.loop-file)
+vgname=vg_replay
+lvname=lv_replay
+replay_dev=/dev/mapper/vg_replay-lv_replay
+snapname=lv_snap
+snap_dev=/dev/mapper/vg_replay-$snapname
+
+$LVM_PROG vgcreate -f $vgname $loop_dev >>$seqres.full 2>&1 || _fail "failed to vgcreate $vgname"
+$LVM_PROG lvcreate -L 4G -n $lvname $vgname -y >>$seqres.full 2>&1 || \
+ _fail "failed to lvcreate $lvname"
+$UDEV_SETTLE_PROG >>$seqres.full 2>&1
+
+replay_log_prog=$here/src/log-writes/replay-log
+num_entries=$($replay_log_prog --log $LOGWRITES_DEV --num-entries)
+entry=$($replay_log_prog --log $LOGWRITES_DEV --replay $replay_dev --find --end-mark mkfs | cut -d@ -f1)
+$replay_log_prog --log $LOGWRITES_DEV --replay $replay_dev --limit $entry || \
+ _fail "failed to replay to start entry $entry"
+let entry+=1
+
+# state = 0: verity hasn't started
+# state = 1: verity underway
+# state = 2: verity done
+state=0
+while [ $entry -lt $num_entries ];
+do
+ $replay_log_prog --limit 1 --log $LOGWRITES_DEV --replay $replay_dev --start $entry || \
+ _fail "failed to take replay step at entry: $entry"
+
+ $LVM_PROG lvcreate -s -L 4M -n $snapname $vgname/$lvname >>$seqres.full 2>&1 || \
+ _fail "Failed to create snapshot"
+ $UDEV_SETTLE_PROG >>$seqres.full 2>&1
+
+ orphan=$(count_item $snap_dev ORPHAN)
+ if [ $state -eq 0 ]; then
+ [ $orphan -gt 0 ] && state=1
+ fi
+
+ pre_mount=$(count_item $snap_dev UNKNOWN.3[67])
+ _mount $snap_dev $SCRATCH_MNT || _fail "mount failed at entry $entry"
+ fsverity measure $SCRATCH_MNT/fsv >>$seqres.full 2>&1
+ measured=$?
+ umount $SCRATCH_MNT
+ [ $state -eq 1 ] && [ $measured -eq 0 ] && state=2
+ [ $state -eq 2 ] && ([ $measured -eq 0 ] || _fail "verity done, but measurement failed at entry $entry")
+ post_mount=$(count_item $snap_dev UNKNOWN.3[67])
+
+ echo "entry: $entry, state: $state, orphan: $orphan, pre_mount: $pre_mount, post_mount: $post_mount" >> $seqres.full
+
+ if [ $state -eq 1 ]; then
+ [ $post_mount -eq 0 ] || \
+ _fail "mount failed to clear under-construction merkle items pre: $pre_mount, post: $post_mount at entry $entry";
+ fi
+ if [ $state -eq 2 ]; then
+ [ $pre_mount -gt 0 ] || \
+ _fail "expected to have verity items before mount at entry $entry"
+ [ $pre_mount -eq $post_mount ] || \
+ _fail "mount cleared merkle items after verity was enabled $pre_mount vs $post_mount at entry $entry";
+ fi
+
+ let entry+=1
+ $LVM_PROG lvremove $vgname/$snapname -y >>$seqres.full
+done
+
+echo "Silence is golden"
+
+# success, all done
+status=0
+exit
new file mode 100644
@@ -0,0 +1,2 @@
+QA output created by 291
+Silence is golden
@@ -239,3 +239,4 @@
234 auto quick compress rw
235 auto quick send
290 auto quick verity
+291 auto verity
The behavior of orphans is most interesting across mounts, interrupted at arbitrary points during fsverity enable. To cover as many such cases as possible, use dmlogwrites and dmsnapshot as in log-writes/replay-individual.sh. At each log entry, we want to assert a somewhat complicated invariant: If verity has not yet started: an orphan indicates that verity has started. If verity has started: mount should handle the orphan and blow away verity data: expect 0 merkle items after mounting the snapshot dev. If we can measure the file, verity has finished. If verity has finished: the orphan should be gone, so mount should not blow away merkle items. Expect the same number of merkle items before and after mounting the snapshot dev. Note that this relies on grepping btrfs inspect-internal dump-tree. Until btrfs-progs has the ability to print the new Merkle items, they will show up as UNKNOWN.36/37. Signed-off-by: Boris Burkov <boris@bur.io> --- tests/btrfs/291 | 156 ++++++++++++++++++++++++++++++++++++++++++++ tests/btrfs/291.out | 2 + tests/btrfs/group | 1 + 3 files changed, 159 insertions(+) create mode 100755 tests/btrfs/291 create mode 100644 tests/btrfs/291.out