diff mbox

[v2] clk: mediatek: adjust dependency of reset.c to avoid unexpectedly being built

Message ID 0a88c7902606e819438ef0f1fc5968960e718620.1515139760.git.sean.wang@mediatek.com (mailing list archive)
State Accepted, archived
Headers show

Commit Message

Sean Wang Jan. 5, 2018, 8:14 a.m. UTC
From: Sean Wang <sean.wang@mediatek.com>

Changes from v1->v2:
Add 'select RESET_CONTROLLER' under COMMON_CLK_MEDIATEK and enable
reset.c to be built when COMMON_CLK_MEDIATEK is selected. That should
be quite reasonable because the reset controller is tightly embedded
inside and exported from these clock subsystems. At least it can be found
on infracfg and pericfg subsystem that both are really fundamental block
lots of devices must depend on.

commit 74cb0d6dde8 ("clk: mediatek: fixup test-building of MediaTek clock
drivers") can let the build system looking into the directory where the
clock drivers resides and then allow test-building the drivers.

But the change also gives rise to certain incorrect behavior which is
reset.c being built even not depending on either COMPILE_TEST or
ARCH_MEDIATEK alternative dependency. To get rid of reset.c being built
unexpectedly on the other platforms, it would be a good change that the
file should be built depending on its own specific configuration rather
than just on generic RESET_CONTROLLER one.

Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Jean Delvare <jdelvare@suse.de>
---
 drivers/clk/mediatek/Kconfig   | 1 +
 drivers/clk/mediatek/Makefile  | 3 +--
 drivers/clk/mediatek/clk-mtk.h | 7 -------
 3 files changed, 2 insertions(+), 9 deletions(-)

Comments

Stephen Boyd Jan. 10, 2018, 9:45 p.m. UTC | #1
On 01/05, sean.wang@mediatek.com wrote:
> From: Sean Wang <sean.wang@mediatek.com>
> 
> Changes from v1->v2:
> Add 'select RESET_CONTROLLER' under COMMON_CLK_MEDIATEK and enable
> reset.c to be built when COMMON_CLK_MEDIATEK is selected. That should
> be quite reasonable because the reset controller is tightly embedded
> inside and exported from these clock subsystems. At least it can be found
> on infracfg and pericfg subsystem that both are really fundamental block
> lots of devices must depend on.
> 
> commit 74cb0d6dde8 ("clk: mediatek: fixup test-building of MediaTek clock
> drivers") can let the build system looking into the directory where the
> clock drivers resides and then allow test-building the drivers.
> 
> But the change also gives rise to certain incorrect behavior which is
> reset.c being built even not depending on either COMPILE_TEST or
> ARCH_MEDIATEK alternative dependency. To get rid of reset.c being built
> unexpectedly on the other platforms, it would be a good change that the
> file should be built depending on its own specific configuration rather
> than just on generic RESET_CONTROLLER one.
> 
> Signed-off-by: Sean Wang <sean.wang@mediatek.com>
> Cc: Jean Delvare <jdelvare@suse.de>
> ---

Applied to clk-next
diff mbox

Patch

diff --git a/drivers/clk/mediatek/Kconfig b/drivers/clk/mediatek/Kconfig
index 7338f81..1f9ea0f 100644
--- a/drivers/clk/mediatek/Kconfig
+++ b/drivers/clk/mediatek/Kconfig
@@ -6,6 +6,7 @@  menu "Clock driver for MediaTek SoC"
 
 config COMMON_CLK_MEDIATEK
 	bool
+	select RESET_CONTROLLER
 	---help---
 	  MediaTek SoCs' clock support.
 
diff --git a/drivers/clk/mediatek/Makefile b/drivers/clk/mediatek/Makefile
index c421ffc..5160fdc 100644
--- a/drivers/clk/mediatek/Makefile
+++ b/drivers/clk/mediatek/Makefile
@@ -1,6 +1,5 @@ 
 # SPDX-License-Identifier: GPL-2.0
-obj-$(CONFIG_COMMON_CLK_MEDIATEK) += clk-mtk.o clk-pll.o clk-gate.o clk-apmixed.o clk-cpumux.o
-obj-$(CONFIG_RESET_CONTROLLER) += reset.o
+obj-$(CONFIG_COMMON_CLK_MEDIATEK) += clk-mtk.o clk-pll.o clk-gate.o clk-apmixed.o clk-cpumux.o reset.o
 obj-$(CONFIG_COMMON_CLK_MT6797) += clk-mt6797.o
 obj-$(CONFIG_COMMON_CLK_MT6797_IMGSYS) += clk-mt6797-img.o
 obj-$(CONFIG_COMMON_CLK_MT6797_MMSYS) += clk-mt6797-mm.o
diff --git a/drivers/clk/mediatek/clk-mtk.h b/drivers/clk/mediatek/clk-mtk.h
index bf8006d..f83c2bb 100644
--- a/drivers/clk/mediatek/clk-mtk.h
+++ b/drivers/clk/mediatek/clk-mtk.h
@@ -229,14 +229,7 @@  void mtk_clk_register_plls(struct device_node *node,
 struct clk *mtk_clk_register_ref2usb_tx(const char *name,
 			const char *parent_name, void __iomem *reg);
 
-#ifdef CONFIG_RESET_CONTROLLER
 void mtk_register_reset_controller(struct device_node *np,
 			unsigned int num_regs, int regofs);
-#else
-static inline void mtk_register_reset_controller(struct device_node *np,
-			unsigned int num_regs, int regofs)
-{
-}
-#endif
 
 #endif /* __DRV_CLK_MTK_H */