@@ -116,6 +116,30 @@ static const struct pll_rate_table *meson_clk_get_pll_settings(struct meson_clk_
return NULL;
}
+/* Specific wait loop for GXL/GXM GP0 PLL */
+static int meson_clk_pll_wait_lock_reset(struct meson_clk_pll *pll,
+ struct parm *p_n)
+{
+ int delay = 100;
+ u32 reg;
+
+ while (delay > 0) {
+ reg = readl(pll->base + p_n->reg_off);
+ writel(reg | MESON_PLL_RESET, pll->base + p_n->reg_off);
+ udelay(10);
+ writel(reg & ~MESON_PLL_RESET, pll->base + p_n->reg_off);
+
+ /* This delay comes from AMLogic tree clk-gp0-gxl driver */
+ mdelay(1);
+
+ reg = readl(pll->base + p_n->reg_off);
+ if (reg & MESON_PLL_LOCK)
+ return 0;
+ delay--;
+ }
+ return -ETIMEDOUT;
+}
+
static int meson_clk_pll_wait_lock(struct meson_clk_pll *pll,
struct parm *p_n)
{
@@ -132,6 +156,15 @@ static int meson_clk_pll_wait_lock(struct meson_clk_pll *pll,
return -ETIMEDOUT;
}
+static void meson_clk_pll_init_params(struct meson_clk_pll *pll)
+{
+ int i;
+
+ for (i = 0 ; i < pll->params.params_count ; ++i)
+ writel(pll->params.params_table[i].value,
+ pll->base + pll->params.params_table[i].reg_off);
+}
+
static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
@@ -151,10 +184,16 @@ static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
if (!rate_set)
return -EINVAL;
+ /* Initialize the PLL in a clean state if specified */
+ if (pll->params.params_count)
+ meson_clk_pll_init_params(pll);
+
/* PLL reset */
p = &pll->n;
reg = readl(pll->base + p->reg_off);
- writel(reg | MESON_PLL_RESET, pll->base + p->reg_off);
+ /* If no_init_reset is provided, avoid resetting at this point */
+ if (!pll->params.no_init_reset)
+ writel(reg | MESON_PLL_RESET, pll->base + p->reg_off);
reg = PARM_SET(p->width, p->shift, reg, rate_set->n);
writel(reg, pll->base + p->reg_off);
@@ -184,7 +223,17 @@ static int meson_clk_pll_set_rate(struct clk_hw *hw, unsigned long rate,
}
p = &pll->n;
- ret = meson_clk_pll_wait_lock(pll, p);
+ /* If clear_reset_for_lock is provided, remove the reset bit here */
+ if (pll->params.clear_reset_for_lock) {
+ reg = readl(pll->base + p->reg_off);
+ writel(reg & ~MESON_PLL_RESET, pll->base + p->reg_off);
+ }
+
+ /* If reset_lock_loop, use a special loop including resetting */
+ if (pll->params.reset_lock_loop)
+ ret = meson_clk_pll_wait_lock_reset(pll, p);
+ else
+ ret = meson_clk_pll_wait_lock(pll, p);
if (ret) {
pr_warn("%s: pll did not lock, trying to restore old rate %lu\n",
__func__, old_rate);
@@ -62,6 +62,28 @@ struct pll_rate_table {
.frac = (_frac), \
} \
+struct pll_params_table {
+ unsigned int reg_off;
+ unsigned int value;
+};
+
+#define PLL_PARAM(_reg, _val) \
+ { \
+ .reg_off = (_reg), \
+ .value = (_val), \
+ }
+
+struct pll_setup_params {
+ struct pll_params_table *params_table;
+ unsigned int params_count;
+ /* Workaround for GP0, do not reset before configuring */
+ bool no_init_reset;
+ /* Workaround for GP0, unreset right before checking for lock */
+ bool clear_reset_for_lock;
+ /* Workaround for GXL GP0, reset in the lock checking loop */
+ bool reset_lock_loop;
+};
+
struct meson_clk_pll {
struct clk_hw hw;
void __iomem *base;
@@ -70,6 +92,7 @@ struct meson_clk_pll {
struct parm frac;
struct parm od;
struct parm od2;
+ const struct pll_setup_params params;
const struct pll_rate_table *rate_table;
unsigned int rate_count;
spinlock_t *lock;
In recent Amlogic GXBB, GXL and GXM SoCs, the GP0 PLL needs some specific parameters in order to initialize and lock correctly. This patch adds an optional PARAM table used to initialize the PLL to a default value with it's parameters in order to achieve to desired frequency. The GP0 PLL in GXBB, GXL/GXM also needs some tweaks in the initialization steps, and these are exposed along the PARAM table. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> --- drivers/clk/meson/clk-pll.c | 53 +++++++++++++++++++++++++++++++++++++++++++-- drivers/clk/meson/clkc.h | 23 ++++++++++++++++++++ 2 files changed, 74 insertions(+), 2 deletions(-)