| Message ID | 1525348355-25471-13-git-send-email-ilialin@codeaurora.org (mailing list archive) |
|---|---|
| State | Superseded, archived |
| Headers | show |
On 03-05-18, 14:52, Ilia Lin wrote: > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors, > the CPU ferequencies subset and voltage value of each OPP varies > based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables > defines the voltage and frequency value based on the msm-id in SMEM > and speedbin blown in the efuse combination. > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC > to provide the OPP framework with required information. > This is used to determine the voltage and frequency value for each OPP of > operating-points-v2 table when it is parsed by the OPP framework. > > Signed-off-by: Ilia Lin <ilialin@codeaurora.org> > --- > drivers/cpufreq/Kconfig.arm | 11 +++ > drivers/cpufreq/Makefile | 1 + > drivers/cpufreq/cpufreq-dt-platdev.c | 3 + > drivers/cpufreq/qcom-cpufreq-kryo.c | 153 +++++++++++++++++++++++++++++++++++ > 4 files changed, 168 insertions(+) > create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c > > diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm > index de55c7d..f9da18c 100644 > --- a/drivers/cpufreq/Kconfig.arm > +++ b/drivers/cpufreq/Kconfig.arm > @@ -124,6 +124,17 @@ config ARM_OMAP2PLUS_CPUFREQ > depends on ARCH_OMAP2PLUS > default ARCH_OMAP2PLUS > > +config ARM_QCOM_CPUFREQ_KRYO > + tristate "Qualcomm Technologies, Inc. Kryo based CPUFreq" I don't see any reply to Sricharan's query on this being tristate. > + depends on QCOM_QFPROM > + depends on QCOM_SMEM > + select PM_OPP > + help > + This adds the CPUFreq driver for > + Qualcomm Technologies, Inc. Kryo SoC based boards. > + > + If in doubt, say N. > + > config ARM_S3C_CPUFREQ > bool > help > diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile > index 8d24ade..fb4a2ec 100644 > --- a/drivers/cpufreq/Makefile > +++ b/drivers/cpufreq/Makefile > @@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o > obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o > obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o > obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o > +obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o > obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o > obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o > obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c > index 3b585e4..77d6ab8 100644 > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > @@ -118,6 +118,9 @@ > > { .compatible = "nvidia,tegra124", }, > > + { .compatible = "qcom,apq8096", }, > + { .compatible = "qcom,msm8996", }, > + > { .compatible = "st,stih407", }, > { .compatible = "st,stih410", }, > > diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c b/drivers/cpufreq/qcom-cpufreq-kryo.c > new file mode 100644 > index 0000000..32371cc > --- /dev/null > +++ b/drivers/cpufreq/qcom-cpufreq-kryo.c > @@ -0,0 +1,153 @@ > +// SPDX-License-Identifier: GPL-2.0 > +/* Copyright (c) 2018, The Linux Foundation. All rights reserved. Incorrect multi line comment. > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 and > + * only version 2 as published by the Free Software Foundation. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/cpu.h> > +#include <linux/err.h> > +#include <linux/init.h> > +//#include <linux/io.h> ?? > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/nvmem-consumer.h> > +#include <linux/of.h> > +#include <linux/platform_device.h> > +#include <linux/pm_opp.h> > +#include <linux/slab.h> > +#include <linux/soc/qcom/smem.h> > + > +#define MSM_ID_SMEM 137 > +#define SILVER_LEAD 0 > +#define GOLD_LEAD 2 > + > +enum _msm_id { > + MSM8996V3 = 0xF6ul, > + APQ8096V3 = 0x123ul, > + MSM8996SG = 0x131ul, > + APQ8096SG = 0x138ul, > +}; > + > +enum _msm8996_version { > + MSM8996_V3, > + MSM8996_SG, > + NUM_OF_MSM8996_VERSIONS, > +}; > + > +static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void) > +{ > + size_t len; > + u32 *msm_id; > + enum _msm8996_version version; > + > + msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len); > + /* The first 4 bytes are format, next to them is the actual msm-id */ > + msm_id++; > + > + switch ((enum _msm_id)*msm_id) { > + case MSM8996V3: > + case APQ8096V3: > + version = MSM8996_V3; > + break; > + case MSM8996SG: > + case APQ8096SG: > + version = MSM8996_SG; > + break; > + default: > + version = NUM_OF_MSM8996_VERSIONS; > + } > + > + return version; > +} > + > +static int __init qcom_cpufreq_kryo_driver_init(void) > +{ > + size_t len; > + int ret; > + u32 versions; > + enum _msm8996_version msm8996_version; > + u8 *speedbin; > + struct platform_device *pdev; > + struct device *cpu_dev; > + struct device_node *np; > + struct nvmem_cell *speedbin_nvmem; > + struct opp_table *opp_temp = NULL; > + > + cpu_dev = get_cpu_device(SILVER_LEAD); > + if (IS_ERR_OR_NULL(cpu_dev)) > + return PTR_ERR(cpu_dev); > + > + msm8996_version = qcom_cpufreq_kryo_get_msm_id(); > + if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { > + dev_err(cpu_dev, "Not Snapdragon 820/821!"); > + return -ENODEV; > + } > + > + np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); > + if (IS_ERR_OR_NULL(np)) > + return PTR_ERR(np); > + > + if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) { > + ret = -ENOENT; > + goto free_np; > + } > + > + speedbin_nvmem = of_nvmem_cell_get(np, NULL); > + if (IS_ERR(speedbin_nvmem)) { > + ret = PTR_ERR(speedbin_nvmem); > + dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret); > + goto free_np; > + } > + > + speedbin = nvmem_cell_read(speedbin_nvmem, &len); > + > + switch (msm8996_version) { > + case MSM8996_V3: > + versions = 1 << (unsigned int)(*speedbin); > + break; > + case MSM8996_SG: > + versions = 1 << ((unsigned int)(*speedbin) + 4); > + break; > + default: > + BUG(); > + break; > + } > + > + ret = PTR_ERR_OR_ZERO(opp_temp = \ > + dev_pm_opp_set_supported_hw(cpu_dev,&versions,1)); > + if (0 > ret) > + goto free_np; > + > + cpu_dev = get_cpu_device(GOLD_LEAD); > + ret = PTR_ERR_OR_ZERO(dev_pm_opp_set_supported_hw(cpu_dev,&versions,1)); > + if (0 > ret) > + goto put_supported_hw_silver; > + > + of_node_put(np); > + > + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0); > + if (IS_ERR(pdev)) { > + return PTR_ERR(pdev); Don't need to free resources on error here ? > + } > + > + return 0; > + > +put_supported_hw_silver: > + dev_pm_opp_put_supported_hw(opp_temp); > + > +free_np: > + of_node_put(np); > + > + return ret; > +} > +late_initcall(qcom_cpufreq_kryo_driver_init); > + > +MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver"); > +MODULE_LICENSE("GPL v2"); > -- > 1.9.1
> -----Original Message----- > From: Viresh Kumar <viresh.kumar@linaro.org> > Sent: Friday, May 4, 2018 09:08 > To: Ilia Lin <ilialin@codeaurora.org> > Cc: mturquette@baylibre.com; sboyd@kernel.org; robh@kernel.org; > mark.rutland@arm.com; rjw@rjwysocki.net; lgirdwood@gmail.com; > broonie@kernel.org; andy.gross@linaro.org; david.brown@linaro.org; > catalin.marinas@arm.com; will.deacon@arm.com; linux-clk@vger.kernel.org; > devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; linux- > pm@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux- > soc@vger.kernel.org; linux-arm-kernel@lists.infradead.org; > rnayak@codeaurora.org; amit.kucheria@linaro.org; > nicolas.dechesne@linaro.org; celster@codeaurora.org; > tfinkel@codeaurora.org > Subject: Re: [PATCH v5 12/14] cpufreq: Add Kryo CPU scaling driver > > On 03-05-18, 14:52, Ilia Lin wrote: > > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO > > processors, the CPU ferequencies subset and voltage value of each OPP > > varies based on the silicon variant in use. Qualcomm Process Voltage > > Scaling Tables defines the voltage and frequency value based on the > > msm-id in SMEM and speedbin blown in the efuse combination. > > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the > > SoC to provide the OPP framework with required information. > > This is used to determine the voltage and frequency value for each OPP > > of > > operating-points-v2 table when it is parsed by the OPP framework. > > > > Signed-off-by: Ilia Lin <ilialin@codeaurora.org> > > --- > > drivers/cpufreq/Kconfig.arm | 11 +++ > > drivers/cpufreq/Makefile | 1 + > > drivers/cpufreq/cpufreq-dt-platdev.c | 3 + > > drivers/cpufreq/qcom-cpufreq-kryo.c | 153 > > +++++++++++++++++++++++++++++++++++ > > 4 files changed, 168 insertions(+) > > create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c > > > > diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm > > index de55c7d..f9da18c 100644 > > --- a/drivers/cpufreq/Kconfig.arm > > +++ b/drivers/cpufreq/Kconfig.arm > > @@ -124,6 +124,17 @@ config ARM_OMAP2PLUS_CPUFREQ > > depends on ARCH_OMAP2PLUS > > default ARCH_OMAP2PLUS > > > > +config ARM_QCOM_CPUFREQ_KRYO > > + tristate "Qualcomm Technologies, Inc. Kryo based CPUFreq" > > I don't see any reply to Sricharan's query on this being tristate. Why shouldn't we leave possibility to compile the cpufreq-dt built-in, and the qcom-cpufreq-kryo module? > > > + depends on QCOM_QFPROM > > + depends on QCOM_SMEM > > + select PM_OPP > > + help > > + This adds the CPUFreq driver for > > + Qualcomm Technologies, Inc. Kryo SoC based boards. > > + > > + If in doubt, say N. > > + > > config ARM_S3C_CPUFREQ > > bool > > help > > diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index > > 8d24ade..fb4a2ec 100644 > > --- a/drivers/cpufreq/Makefile > > +++ b/drivers/cpufreq/Makefile > > @@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += > mvebu-cpufreq.o > > obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o > > obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o > > obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o > > +obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq- > kryo.o > > obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o > > obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o > > obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o > > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c > > b/drivers/cpufreq/cpufreq-dt-platdev.c > > index 3b585e4..77d6ab8 100644 > > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > > @@ -118,6 +118,9 @@ > > > > { .compatible = "nvidia,tegra124", }, > > > > + { .compatible = "qcom,apq8096", }, > > + { .compatible = "qcom,msm8996", }, > > + > > { .compatible = "st,stih407", }, > > { .compatible = "st,stih410", }, > > > > diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c > > b/drivers/cpufreq/qcom-cpufreq-kryo.c > > new file mode 100644 > > index 0000000..32371cc > > --- /dev/null > > +++ b/drivers/cpufreq/qcom-cpufreq-kryo.c > > @@ -0,0 +1,153 @@ > > +// SPDX-License-Identifier: GPL-2.0 > > +/* Copyright (c) 2018, The Linux Foundation. All rights reserved. > > Incorrect multi line comment. This was done as per Bjorn's instruction. > > > + * > > + * This program is free software; you can redistribute it and/or > > + modify > > + * it under the terms of the GNU General Public License version 2 and > > + * only version 2 as published by the Free Software Foundation. > > + * > > + * This program is distributed in the hope that it will be useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + */ > > + > > +#include <linux/cpu.h> > > +#include <linux/err.h> > > +#include <linux/init.h> > > +//#include <linux/io.h> > > ?? Not good. Will fix this.bbbbbbbb > > > +#include <linux/kernel.h> > > +#include <linux/module.h> > > +#include <linux/nvmem-consumer.h> > > +#include <linux/of.h> > > +#include <linux/platform_device.h> > > +#include <linux/pm_opp.h> > > +#include <linux/slab.h> > > +#include <linux/soc/qcom/smem.h> > > + > > +#define MSM_ID_SMEM 137 > > +#define SILVER_LEAD 0 > > +#define GOLD_LEAD 2 > > + > > +enum _msm_id { > > + MSM8996V3 = 0xF6ul, > > + APQ8096V3 = 0x123ul, > > + MSM8996SG = 0x131ul, > > + APQ8096SG = 0x138ul, > > +}; > > + > > +enum _msm8996_version { > > + MSM8996_V3, > > + MSM8996_SG, > > + NUM_OF_MSM8996_VERSIONS, > > +}; > > + > > +static enum _msm8996_version __init > > +qcom_cpufreq_kryo_get_msm_id(void) > > +{ > > + size_t len; > > + u32 *msm_id; > > + enum _msm8996_version version; > > + > > + msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, > MSM_ID_SMEM, &len); > > + /* The first 4 bytes are format, next to them is the actual msm-id */ > > + msm_id++; > > + > > + switch ((enum _msm_id)*msm_id) { > > + case MSM8996V3: > > + case APQ8096V3: > > + version = MSM8996_V3; > > + break; > > + case MSM8996SG: > > + case APQ8096SG: > > + version = MSM8996_SG; > > + break; > > + default: > > + version = NUM_OF_MSM8996_VERSIONS; > > + } > > + > > + return version; > > +} > > + > > +static int __init qcom_cpufreq_kryo_driver_init(void) > > +{ > > + size_t len; > > + int ret; > > + u32 versions; > > + enum _msm8996_version msm8996_version; > > + u8 *speedbin; > > + struct platform_device *pdev; > > + struct device *cpu_dev; > > + struct device_node *np; > > + struct nvmem_cell *speedbin_nvmem; > > + struct opp_table *opp_temp = NULL; > > + > > + cpu_dev = get_cpu_device(SILVER_LEAD); > > + if (IS_ERR_OR_NULL(cpu_dev)) > > + return PTR_ERR(cpu_dev); > > + > > + msm8996_version = qcom_cpufreq_kryo_get_msm_id(); > > + if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { > > + dev_err(cpu_dev, "Not Snapdragon 820/821!"); > > + return -ENODEV; > > + } > > + > > + np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); > > + if (IS_ERR_OR_NULL(np)) > > + return PTR_ERR(np); > > + > > + if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) { > > + ret = -ENOENT; > > + goto free_np; > > + } > > + > > + speedbin_nvmem = of_nvmem_cell_get(np, NULL); > > + if (IS_ERR(speedbin_nvmem)) { > > + ret = PTR_ERR(speedbin_nvmem); > > + dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret); > > + goto free_np; > > + } > > + > > + speedbin = nvmem_cell_read(speedbin_nvmem, &len); > > + > > + switch (msm8996_version) { > > + case MSM8996_V3: > > + versions = 1 << (unsigned int)(*speedbin); > > + break; > > + case MSM8996_SG: > > + versions = 1 << ((unsigned int)(*speedbin) + 4); > > + break; > > + default: > > + BUG(); > > + break; > > + } > > + > > + ret = PTR_ERR_OR_ZERO(opp_temp = \ > > + > dev_pm_opp_set_supported_hw(cpu_dev,&versions,1)); > > + if (0 > ret) > > + goto free_np; > > + > > + cpu_dev = get_cpu_device(GOLD_LEAD); > > + ret = > PTR_ERR_OR_ZERO(dev_pm_opp_set_supported_hw(cpu_dev,&versions,1 > )); > > + if (0 > ret) > > + goto put_supported_hw_silver; > > + > > + of_node_put(np); > > + > > + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0); > > + if (IS_ERR(pdev)) { > > + return PTR_ERR(pdev); > > Don't need to free resources on error here ? You are right. Will fix. > > > + } > > + > > + return 0; > > + > > +put_supported_hw_silver: > > + dev_pm_opp_put_supported_hw(opp_temp); > > + > > +free_np: > > + of_node_put(np); > > + > > + return ret; > > +} > > +late_initcall(qcom_cpufreq_kryo_driver_init); > > + > > +MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq > > +driver"); MODULE_LICENSE("GPL v2"); > > -- > > 1.9.1 > > -- > viresh -- To unsubscribe from this list: send the line "unsubscribe linux-clk" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 04-05-18, 09:44, ilialin@codeaurora.org wrote: > > > > -----Original Message----- > > From: Viresh Kumar <viresh.kumar@linaro.org> > > Sent: Friday, May 4, 2018 09:08 > > To: Ilia Lin <ilialin@codeaurora.org> > > Cc: mturquette@baylibre.com; sboyd@kernel.org; robh@kernel.org; > > mark.rutland@arm.com; rjw@rjwysocki.net; lgirdwood@gmail.com; > > broonie@kernel.org; andy.gross@linaro.org; david.brown@linaro.org; > > catalin.marinas@arm.com; will.deacon@arm.com; linux-clk@vger.kernel.org; > > devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; linux- > > pm@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux- > > soc@vger.kernel.org; linux-arm-kernel@lists.infradead.org; > > rnayak@codeaurora.org; amit.kucheria@linaro.org; > > nicolas.dechesne@linaro.org; celster@codeaurora.org; > > tfinkel@codeaurora.org > > Subject: Re: [PATCH v5 12/14] cpufreq: Add Kryo CPU scaling driver > > > > On 03-05-18, 14:52, Ilia Lin wrote: > > > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO > > > processors, the CPU ferequencies subset and voltage value of each OPP > > > varies based on the silicon variant in use. Qualcomm Process Voltage > > > Scaling Tables defines the voltage and frequency value based on the > > > msm-id in SMEM and speedbin blown in the efuse combination. > > > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the > > > SoC to provide the OPP framework with required information. > > > This is used to determine the voltage and frequency value for each OPP > > > of > > > operating-points-v2 table when it is parsed by the OPP framework. > > > > > > Signed-off-by: Ilia Lin <ilialin@codeaurora.org> > > > --- > > > drivers/cpufreq/Kconfig.arm | 11 +++ > > > drivers/cpufreq/Makefile | 1 + > > > drivers/cpufreq/cpufreq-dt-platdev.c | 3 + > > > drivers/cpufreq/qcom-cpufreq-kryo.c | 153 > > > +++++++++++++++++++++++++++++++++++ > > > 4 files changed, 168 insertions(+) > > > create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c > > > > > > diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm > > > index de55c7d..f9da18c 100644 > > > --- a/drivers/cpufreq/Kconfig.arm > > > +++ b/drivers/cpufreq/Kconfig.arm > > > @@ -124,6 +124,17 @@ config ARM_OMAP2PLUS_CPUFREQ > > > depends on ARCH_OMAP2PLUS > > > default ARCH_OMAP2PLUS > > > > > > +config ARM_QCOM_CPUFREQ_KRYO > > > + tristate "Qualcomm Technologies, Inc. Kryo based CPUFreq" > > > > I don't see any reply to Sricharan's query on this being tristate. > > Why shouldn't we leave possibility to compile the cpufreq-dt built-in, and > the qcom-cpufreq-kryo module? I was not saying this is incorrect, all I am saying is that you never replied to a comment from one of the reviewers. And I don't see a reason why this should be a tristate really. cpufreq-dt is already capable of being a module, all your driver does is that it creates the cpufreq-dt platform device after setting the OPP hw properties.. Over that, have you ever tried inserting, then removing and inserting the driver module again? I feel it will fail. The reason is that you never provided an exit routine which can get rid of the platform device created in the first place. > > > + depends on QCOM_QFPROM > > > + depends on QCOM_SMEM > > > + select PM_OPP > > > + help > > > + This adds the CPUFreq driver for > > > + Qualcomm Technologies, Inc. Kryo SoC based boards. > > > + > > > + If in doubt, say N. > > > + > > > config ARM_S3C_CPUFREQ > > > bool > > > help > > > diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index > > > 8d24ade..fb4a2ec 100644 > > > --- a/drivers/cpufreq/Makefile > > > +++ b/drivers/cpufreq/Makefile > > > @@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += > > mvebu-cpufreq.o > > > obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o > > > obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o > > > obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o > > > +obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq- > > kryo.o > > > obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o > > > obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o > > > obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o > > > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c > > > b/drivers/cpufreq/cpufreq-dt-platdev.c > > > index 3b585e4..77d6ab8 100644 > > > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > > > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > > > @@ -118,6 +118,9 @@ > > > > > > { .compatible = "nvidia,tegra124", }, > > > > > > + { .compatible = "qcom,apq8096", }, > > > + { .compatible = "qcom,msm8996", }, > > > + > > > { .compatible = "st,stih407", }, > > > { .compatible = "st,stih410", }, > > > > > > diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c > > > b/drivers/cpufreq/qcom-cpufreq-kryo.c > > > new file mode 100644 > > > index 0000000..32371cc > > > --- /dev/null > > > +++ b/drivers/cpufreq/qcom-cpufreq-kryo.c > > > @@ -0,0 +1,153 @@ > > > +// SPDX-License-Identifier: GPL-2.0 > > > +/* Copyright (c) 2018, The Linux Foundation. All rights reserved. > > > > Incorrect multi line comment. > > This was done as per Bjorn's instruction. You haven't followed him correctly. What he asked for is: // SPDX... /* * XXXX */ What you have done is: // SPDX... /* XXXX */
> -----Original Message----- > From: Viresh Kumar <viresh.kumar@linaro.org> > Sent: Friday, May 4, 2018 09:57 > To: ilialin@codeaurora.org > Cc: mturquette@baylibre.com; sboyd@kernel.org; robh@kernel.org; > mark.rutland@arm.com; rjw@rjwysocki.net; lgirdwood@gmail.com; > broonie@kernel.org; andy.gross@linaro.org; david.brown@linaro.org; > catalin.marinas@arm.com; will.deacon@arm.com; linux-clk@vger.kernel.org; > devicetree@vger.kernel.org; linux-kernel@vger.kernel.org; linux- > pm@vger.kernel.org; linux-arm-msm@vger.kernel.org; linux- > soc@vger.kernel.org; linux-arm-kernel@lists.infradead.org; > rnayak@codeaurora.org; amit.kucheria@linaro.org; > nicolas.dechesne@linaro.org; celster@codeaurora.org; > tfinkel@codeaurora.org > Subject: Re: [PATCH v5 12/14] cpufreq: Add Kryo CPU scaling driver > > On 04-05-18, 09:44, ilialin@codeaurora.org wrote: > > > > > > > -----Original Message----- > > > From: Viresh Kumar <viresh.kumar@linaro.org> > > > Sent: Friday, May 4, 2018 09:08 > > > To: Ilia Lin <ilialin@codeaurora.org> > > > Cc: mturquette@baylibre.com; sboyd@kernel.org; robh@kernel.org; > > > mark.rutland@arm.com; rjw@rjwysocki.net; lgirdwood@gmail.com; > > > broonie@kernel.org; andy.gross@linaro.org; david.brown@linaro.org; > > > catalin.marinas@arm.com; will.deacon@arm.com; > > > linux-clk@vger.kernel.org; devicetree@vger.kernel.org; > > > linux-kernel@vger.kernel.org; linux- pm@vger.kernel.org; > > > linux-arm-msm@vger.kernel.org; linux- soc@vger.kernel.org; > > > linux-arm-kernel@lists.infradead.org; > > > rnayak@codeaurora.org; amit.kucheria@linaro.org; > > > nicolas.dechesne@linaro.org; celster@codeaurora.org; > > > tfinkel@codeaurora.org > > > Subject: Re: [PATCH v5 12/14] cpufreq: Add Kryo CPU scaling driver > > > > > > On 03-05-18, 14:52, Ilia Lin wrote: > > > > In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO > > > > processors, the CPU ferequencies subset and voltage value of each > > > > OPP varies based on the silicon variant in use. Qualcomm Process > > > > Voltage Scaling Tables defines the voltage and frequency value > > > > based on the msm-id in SMEM and speedbin blown in the efuse > combination. > > > > The qcom-cpufreq-kryo driver reads the msm-id and efuse value from > > > > the SoC to provide the OPP framework with required information. > > > > This is used to determine the voltage and frequency value for each > > > > OPP of > > > > operating-points-v2 table when it is parsed by the OPP framework. > > > > > > > > Signed-off-by: Ilia Lin <ilialin@codeaurora.org> > > > > --- > > > > drivers/cpufreq/Kconfig.arm | 11 +++ > > > > drivers/cpufreq/Makefile | 1 + > > > > drivers/cpufreq/cpufreq-dt-platdev.c | 3 + > > > > drivers/cpufreq/qcom-cpufreq-kryo.c | 153 > > > > +++++++++++++++++++++++++++++++++++ > > > > 4 files changed, 168 insertions(+) create mode 100644 > > > > drivers/cpufreq/qcom-cpufreq-kryo.c > > > > > > > > diff --git a/drivers/cpufreq/Kconfig.arm > > > > b/drivers/cpufreq/Kconfig.arm index de55c7d..f9da18c 100644 > > > > --- a/drivers/cpufreq/Kconfig.arm > > > > +++ b/drivers/cpufreq/Kconfig.arm > > > > @@ -124,6 +124,17 @@ config ARM_OMAP2PLUS_CPUFREQ > > > > depends on ARCH_OMAP2PLUS > > > > default ARCH_OMAP2PLUS > > > > > > > > +config ARM_QCOM_CPUFREQ_KRYO > > > > + tristate "Qualcomm Technologies, Inc. Kryo based CPUFreq" > > > > > > I don't see any reply to Sricharan's query on this being tristate. > > > > Why shouldn't we leave possibility to compile the cpufreq-dt built-in, > > and the qcom-cpufreq-kryo module? > > I was not saying this is incorrect, all I am saying is that you never replied to a > comment from one of the reviewers. > > And I don't see a reason why this should be a tristate really. > cpufreq-dt is already capable of being a module, all your driver does is that it > creates the cpufreq-dt platform device after setting the OPP hw properties.. > > Over that, have you ever tried inserting, then removing and inserting the > driver module again? I feel it will fail. > > The reason is that you never provided an exit routine which can get rid of the > platform device created in the first place. Convinced. I'll change it to bool. > > > > > + depends on QCOM_QFPROM > > > > + depends on QCOM_SMEM > > > > + select PM_OPP > > > > + help > > > > + This adds the CPUFreq driver for > > > > + Qualcomm Technologies, Inc. Kryo SoC based boards. > > > > + > > > > + If in doubt, say N. > > > > + > > > > config ARM_S3C_CPUFREQ > > > > bool > > > > help > > > > diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile > > > > index 8d24ade..fb4a2ec 100644 > > > > --- a/drivers/cpufreq/Makefile > > > > +++ b/drivers/cpufreq/Makefile > > > > @@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += > > > mvebu-cpufreq.o > > > > obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o > > > > obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o > > > > obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o > > > > +obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq- > > > kryo.o > > > > obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o > > > > obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o > > > > obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o > > > > diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c > > > > b/drivers/cpufreq/cpufreq-dt-platdev.c > > > > index 3b585e4..77d6ab8 100644 > > > > --- a/drivers/cpufreq/cpufreq-dt-platdev.c > > > > +++ b/drivers/cpufreq/cpufreq-dt-platdev.c > > > > @@ -118,6 +118,9 @@ > > > > > > > > { .compatible = "nvidia,tegra124", }, > > > > > > > > + { .compatible = "qcom,apq8096", }, > > > > + { .compatible = "qcom,msm8996", }, > > > > + > > > > { .compatible = "st,stih407", }, > > > > { .compatible = "st,stih410", }, > > > > > > > > diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c > > > > b/drivers/cpufreq/qcom-cpufreq-kryo.c > > > > new file mode 100644 > > > > index 0000000..32371cc > > > > --- /dev/null > > > > +++ b/drivers/cpufreq/qcom-cpufreq-kryo.c > > > > @@ -0,0 +1,153 @@ > > > > +// SPDX-License-Identifier: GPL-2.0 > > > > +/* Copyright (c) 2018, The Linux Foundation. All rights reserved. > > > > > > Incorrect multi line comment. > > > > This was done as per Bjorn's instruction. > > You haven't followed him correctly. > > What he asked for is: > > // SPDX... > /* > * XXXX > */ > > What you have done is: > > // SPDX... > /* XXXX > */ OK. Got you. Will fix. > > -- > viresh -- To unsubscribe from this list: send the line "unsubscribe linux-clk" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm index de55c7d..f9da18c 100644 --- a/drivers/cpufreq/Kconfig.arm +++ b/drivers/cpufreq/Kconfig.arm @@ -124,6 +124,17 @@ config ARM_OMAP2PLUS_CPUFREQ depends on ARCH_OMAP2PLUS default ARCH_OMAP2PLUS +config ARM_QCOM_CPUFREQ_KRYO + tristate "Qualcomm Technologies, Inc. Kryo based CPUFreq" + depends on QCOM_QFPROM + depends on QCOM_SMEM + select PM_OPP + help + This adds the CPUFreq driver for + Qualcomm Technologies, Inc. Kryo SoC based boards. + + If in doubt, say N. + config ARM_S3C_CPUFREQ bool help diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile index 8d24ade..fb4a2ec 100644 --- a/drivers/cpufreq/Makefile +++ b/drivers/cpufreq/Makefile @@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o +obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c index 3b585e4..77d6ab8 100644 --- a/drivers/cpufreq/cpufreq-dt-platdev.c +++ b/drivers/cpufreq/cpufreq-dt-platdev.c @@ -118,6 +118,9 @@ { .compatible = "nvidia,tegra124", }, + { .compatible = "qcom,apq8096", }, + { .compatible = "qcom,msm8996", }, + { .compatible = "st,stih407", }, { .compatible = "st,stih410", }, diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c b/drivers/cpufreq/qcom-cpufreq-kryo.c new file mode 100644 index 0000000..32371cc --- /dev/null +++ b/drivers/cpufreq/qcom-cpufreq-kryo.c @@ -0,0 +1,153 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018, The Linux Foundation. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 and + * only version 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/cpu.h> +#include <linux/err.h> +#include <linux/init.h> +//#include <linux/io.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/nvmem-consumer.h> +#include <linux/of.h> +#include <linux/platform_device.h> +#include <linux/pm_opp.h> +#include <linux/slab.h> +#include <linux/soc/qcom/smem.h> + +#define MSM_ID_SMEM 137 +#define SILVER_LEAD 0 +#define GOLD_LEAD 2 + +enum _msm_id { + MSM8996V3 = 0xF6ul, + APQ8096V3 = 0x123ul, + MSM8996SG = 0x131ul, + APQ8096SG = 0x138ul, +}; + +enum _msm8996_version { + MSM8996_V3, + MSM8996_SG, + NUM_OF_MSM8996_VERSIONS, +}; + +static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void) +{ + size_t len; + u32 *msm_id; + enum _msm8996_version version; + + msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len); + /* The first 4 bytes are format, next to them is the actual msm-id */ + msm_id++; + + switch ((enum _msm_id)*msm_id) { + case MSM8996V3: + case APQ8096V3: + version = MSM8996_V3; + break; + case MSM8996SG: + case APQ8096SG: + version = MSM8996_SG; + break; + default: + version = NUM_OF_MSM8996_VERSIONS; + } + + return version; +} + +static int __init qcom_cpufreq_kryo_driver_init(void) +{ + size_t len; + int ret; + u32 versions; + enum _msm8996_version msm8996_version; + u8 *speedbin; + struct platform_device *pdev; + struct device *cpu_dev; + struct device_node *np; + struct nvmem_cell *speedbin_nvmem; + struct opp_table *opp_temp = NULL; + + cpu_dev = get_cpu_device(SILVER_LEAD); + if (IS_ERR_OR_NULL(cpu_dev)) + return PTR_ERR(cpu_dev); + + msm8996_version = qcom_cpufreq_kryo_get_msm_id(); + if (NUM_OF_MSM8996_VERSIONS == msm8996_version) { + dev_err(cpu_dev, "Not Snapdragon 820/821!"); + return -ENODEV; + } + + np = dev_pm_opp_of_get_opp_desc_node(cpu_dev); + if (IS_ERR_OR_NULL(np)) + return PTR_ERR(np); + + if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) { + ret = -ENOENT; + goto free_np; + } + + speedbin_nvmem = of_nvmem_cell_get(np, NULL); + if (IS_ERR(speedbin_nvmem)) { + ret = PTR_ERR(speedbin_nvmem); + dev_err(cpu_dev, "Could not get nvmem cell: %d\n", ret); + goto free_np; + } + + speedbin = nvmem_cell_read(speedbin_nvmem, &len); + + switch (msm8996_version) { + case MSM8996_V3: + versions = 1 << (unsigned int)(*speedbin); + break; + case MSM8996_SG: + versions = 1 << ((unsigned int)(*speedbin) + 4); + break; + default: + BUG(); + break; + } + + ret = PTR_ERR_OR_ZERO(opp_temp = \ + dev_pm_opp_set_supported_hw(cpu_dev,&versions,1)); + if (0 > ret) + goto free_np; + + cpu_dev = get_cpu_device(GOLD_LEAD); + ret = PTR_ERR_OR_ZERO(dev_pm_opp_set_supported_hw(cpu_dev,&versions,1)); + if (0 > ret) + goto put_supported_hw_silver; + + of_node_put(np); + + pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0); + if (IS_ERR(pdev)) { + return PTR_ERR(pdev); + } + + return 0; + +put_supported_hw_silver: + dev_pm_opp_put_supported_hw(opp_temp); + +free_np: + of_node_put(np); + + return ret; +} +late_initcall(qcom_cpufreq_kryo_driver_init); + +MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver"); +MODULE_LICENSE("GPL v2");
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors, the CPU ferequencies subset and voltage value of each OPP varies based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables defines the voltage and frequency value based on the msm-id in SMEM and speedbin blown in the efuse combination. The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC to provide the OPP framework with required information. This is used to determine the voltage and frequency value for each OPP of operating-points-v2 table when it is parsed by the OPP framework. Signed-off-by: Ilia Lin <ilialin@codeaurora.org> --- drivers/cpufreq/Kconfig.arm | 11 +++ drivers/cpufreq/Makefile | 1 + drivers/cpufreq/cpufreq-dt-platdev.c | 3 + drivers/cpufreq/qcom-cpufreq-kryo.c | 153 +++++++++++++++++++++++++++++++++++ 4 files changed, 168 insertions(+) create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c