| Message ID | 20170514163045.40366-12-icenowy@aosc.io (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
On Mon, May 15, 2017 at 12:30:43AM +0800, Icenowy Zheng wrote: > + de2_clocks: clock@1000000 { display_clocks would be better there, we don't have to dissociate de1 with de2 > + compatible = "allwinner,sun8i-v3s-de2-clk"; > + reg = <0x01000000 0x100000>; > + clocks = <&ccu CLK_DE>, > + <&ccu CLK_BUS_DE>; > + clock-names = "mod", > + "bus"; > + resets = <&ccu RST_BUS_DE>; > + #clock-cells = <1>; > + #reset-cells = <1>; > + }; > + > + de2_mixer0: mixer@1100000 { and mixer0 here is enough too. Is there several of them? Why not just use mixer if there's only one? > + compatible = "allwinner,sun8i-v3s-de2-mixer"; > + reg = <0x01100000 0x100000>; > + clocks = <&de2_clocks CLK_MIXER0>, > + <&de2_clocks CLK_BUS_MIXER0>; > + clock-names = "mod", > + "bus"; > + resets = <&de2_clocks RST_MIXER0>; > + assigned-clocks = <&de2_clocks CLK_MIXER0>; > + assigned-clock-rates = <150000000>; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + mixer0_out: port@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + > + mixer0_out_tcon0: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&tcon0_in_mixer0>; > + }; > + }; > + }; > + }; > + > + tcon0: lcd-controller@1c0c000 { > + compatible = "allwinner,sun8i-v3s-tcon"; > + reg = <0x01c0c000 0x1000>; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&ccu CLK_BUS_TCON0>, > + <&ccu CLK_TCON0>; > + clock-names = "ahb", > + "tcon-ch0"; > + clock-output-names = "tcon-pixel-clock"; > + resets = <&ccu RST_BUS_TCON0>; > + reset-names = "lcd"; > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + tcon0_in: port@0 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + tcon0_in_mixer0: endpoint@0 { > + reg = <0>; > + remote-endpoint = <&mixer0_out_tcon0>; > + }; > + }; > + > + tcon0_out: port@1 { > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <1>; > + }; > + }; > + }; > + > + You have an extra new line here. Maxime
在 2017-05-15 17:24，Maxime Ripard 写道： > On Mon, May 15, 2017 at 12:30:43AM +0800, Icenowy Zheng wrote: >> + de2_clocks: clock@1000000 { > > display_clocks would be better there, we don't have to dissociate de1 > with de2 How about de_clocks ? (See A80 DTSI) > >> + compatible = "allwinner,sun8i-v3s-de2-clk"; >> + reg = <0x01000000 0x100000>; >> + clocks = <&ccu CLK_DE>, >> + <&ccu CLK_BUS_DE>; >> + clock-names = "mod", >> + "bus"; >> + resets = <&ccu RST_BUS_DE>; >> + #clock-cells = <1>; >> + #reset-cells = <1>; >> + }; >> + >> + de2_mixer0: mixer@1100000 { > > and mixer0 here is enough too. > > Is there several of them? Why not just use mixer if there's only one? Nope, here it's tagged 0 only for consistency with other SoCs. > >> + compatible = "allwinner,sun8i-v3s-de2-mixer"; >> + reg = <0x01100000 0x100000>; >> + clocks = <&de2_clocks CLK_MIXER0>, >> + <&de2_clocks CLK_BUS_MIXER0>; >> + clock-names = "mod", >> + "bus"; >> + resets = <&de2_clocks RST_MIXER0>; >> + assigned-clocks = <&de2_clocks CLK_MIXER0>; >> + assigned-clock-rates = <150000000>; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + mixer0_out: port@1 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <1>; >> + >> + mixer0_out_tcon0: endpoint@0 { >> + reg = <0>; >> + remote-endpoint = <&tcon0_in_mixer0>; >> + }; >> + }; >> + }; >> + }; >> + >> + tcon0: lcd-controller@1c0c000 { >> + compatible = "allwinner,sun8i-v3s-tcon"; >> + reg = <0x01c0c000 0x1000>; >> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; >> + clocks = <&ccu CLK_BUS_TCON0>, >> + <&ccu CLK_TCON0>; >> + clock-names = "ahb", >> + "tcon-ch0"; >> + clock-output-names = "tcon-pixel-clock"; >> + resets = <&ccu RST_BUS_TCON0>; >> + reset-names = "lcd"; >> + status = "disabled"; >> + >> + ports { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + tcon0_in: port@0 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <0>; >> + >> + tcon0_in_mixer0: endpoint@0 { >> + reg = <0>; >> + remote-endpoint = <&mixer0_out_tcon0>; >> + }; >> + }; >> + >> + tcon0_out: port@1 { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + reg = <1>; >> + }; >> + }; >> + }; >> + >> + > > You have an extra new line here. > > Maxime -- To unsubscribe from this list: send the line "unsubscribe linux-clk" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
在 2017-05-17 17:27，icenowy@aosc.io 写道： > 在 2017-05-15 17:24，Maxime Ripard 写道： >> On Mon, May 15, 2017 at 12:30:43AM +0800, Icenowy Zheng wrote: >>> + de2_clocks: clock@1000000 { >> >> display_clocks would be better there, we don't have to dissociate de1 >> with de2 > > How about de_clocks ? (See A80 DTSI) Oh I regretted... de here indicates "de1". display_clocks is better. > >> >>> + compatible = "allwinner,sun8i-v3s-de2-clk"; >>> + reg = <0x01000000 0x100000>; >>> + clocks = <&ccu CLK_DE>, >>> + <&ccu CLK_BUS_DE>; >>> + clock-names = "mod", >>> + "bus"; >>> + resets = <&ccu RST_BUS_DE>; >>> + #clock-cells = <1>; >>> + #reset-cells = <1>; >>> + }; >>> + >>> + de2_mixer0: mixer@1100000 { >> >> and mixer0 here is enough too. >> >> Is there several of them? Why not just use mixer if there's only one? > > Nope, here it's tagged 0 only for consistency with other SoCs. > >> >>> + compatible = "allwinner,sun8i-v3s-de2-mixer"; >>> + reg = <0x01100000 0x100000>; >>> + clocks = <&de2_clocks CLK_MIXER0>, >>> + <&de2_clocks CLK_BUS_MIXER0>; >>> + clock-names = "mod", >>> + "bus"; >>> + resets = <&de2_clocks RST_MIXER0>; >>> + assigned-clocks = <&de2_clocks CLK_MIXER0>; >>> + assigned-clock-rates = <150000000>; >>> + >>> + ports { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + mixer0_out: port@1 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + reg = <1>; >>> + >>> + mixer0_out_tcon0: endpoint@0 { >>> + reg = <0>; >>> + remote-endpoint = <&tcon0_in_mixer0>; >>> + }; >>> + }; >>> + }; >>> + }; >>> + >>> + tcon0: lcd-controller@1c0c000 { >>> + compatible = "allwinner,sun8i-v3s-tcon"; >>> + reg = <0x01c0c000 0x1000>; >>> + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; >>> + clocks = <&ccu CLK_BUS_TCON0>, >>> + <&ccu CLK_TCON0>; >>> + clock-names = "ahb", >>> + "tcon-ch0"; >>> + clock-output-names = "tcon-pixel-clock"; >>> + resets = <&ccu RST_BUS_TCON0>; >>> + reset-names = "lcd"; >>> + status = "disabled"; >>> + >>> + ports { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + tcon0_in: port@0 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + reg = <0>; >>> + >>> + tcon0_in_mixer0: endpoint@0 { >>> + reg = <0>; >>> + remote-endpoint = <&mixer0_out_tcon0>; >>> + }; >>> + }; >>> + >>> + tcon0_out: port@1 { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + reg = <1>; >>> + }; >>> + }; >>> + }; >>> + >>> + >> >> You have an extra new line here. >> >> Maxime -- To unsubscribe from this list: send the line "unsubscribe linux-clk" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi index 71075969e5e6..b71b35734515 100644 --- a/arch/arm/boot/dts/sun8i-v3s.dtsi +++ b/arch/arm/boot/dts/sun8i-v3s.dtsi @@ -41,6 +41,10 @@ */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/clock/sun8i-v3s-ccu.h> +#include <dt-bindings/clock/sun8i-de2.h> +#include <dt-bindings/reset/sun8i-v3s-ccu.h> +#include <dt-bindings/reset/sun8i-de2.h> / { #address-cells = <1>; @@ -59,6 +63,12 @@ }; }; + de: display-engine { + compatible = "allwinner,sun8i-v3s-display-engine"; + allwinner,pipelines = <&de2_mixer0>; + status = "disabled"; + }; + timer { compatible = "arm,armv7-timer"; interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, @@ -93,6 +103,83 @@ #size-cells = <1>; ranges; + de2_clocks: clock@1000000 { + compatible = "allwinner,sun8i-v3s-de2-clk"; + reg = <0x01000000 0x100000>; + clocks = <&ccu CLK_DE>, + <&ccu CLK_BUS_DE>; + clock-names = "mod", + "bus"; + resets = <&ccu RST_BUS_DE>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + de2_mixer0: mixer@1100000 { + compatible = "allwinner,sun8i-v3s-de2-mixer"; + reg = <0x01100000 0x100000>; + clocks = <&de2_clocks CLK_MIXER0>, + <&de2_clocks CLK_BUS_MIXER0>; + clock-names = "mod", + "bus"; + resets = <&de2_clocks RST_MIXER0>; + assigned-clocks = <&de2_clocks CLK_MIXER0>; + assigned-clock-rates = <150000000>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + mixer0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + mixer0_out_tcon0: endpoint@0 { + reg = <0>; + remote-endpoint = <&tcon0_in_mixer0>; + }; + }; + }; + }; + + tcon0: lcd-controller@1c0c000 { + compatible = "allwinner,sun8i-v3s-tcon"; + reg = <0x01c0c000 0x1000>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_TCON0>, + <&ccu CLK_TCON0>; + clock-names = "ahb", + "tcon-ch0"; + clock-output-names = "tcon-pixel-clock"; + resets = <&ccu RST_BUS_TCON0>; + reset-names = "lcd"; + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + tcon0_in: port@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + tcon0_in_mixer0: endpoint@0 { + reg = <0>; + remote-endpoint = <&mixer0_out_tcon0>; + }; + }; + + tcon0_out: port@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + }; + }; + }; + + mmc0: mmc@01c0f000 { compatible = "allwinner,sun7i-a20-mmc"; reg = <0x01c0f000 0x1000>;
Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer and only one TCON connected to this mixer, which have RGB LCD output. Add device nodes for this display pipeline. Signed-off-by: Icenowy Zheng <icenowy@aosc.io> --- Changes in v7: - Change DE2 clock compatible to V3s one. - Mention only one TCON in commit message. - Changed commit brief. arch/arm/boot/dts/sun8i-v3s.dtsi | 87 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 87 insertions(+)