@@ -30,11 +30,6 @@
#include "cpuidle.h"
#include "sram.h"
-#ifndef CONFIG_COMMON_CLK
-#include <mach/clock.h>
-#include "clock.h"
-#endif
-
#define DA8XX_TPCC_BASE 0x01c00000
#define DA8XX_TPTC0_BASE 0x01c08000
#define DA8XX_TPTC1_BASE 0x01c08400
@@ -1045,29 +1040,6 @@ int __init da8xx_register_spi_bus(int instance, unsigned num_chipselect)
}
#ifdef CONFIG_ARCH_DAVINCI_DA850
-#ifndef CONFIG_COMMON_CLK
-static struct clk sata_refclk = {
- .name = "sata_refclk",
- .set_rate = davinci_simple_set_rate,
-};
-
-static struct clk_lookup sata_refclk_lookup =
- CLK("ahci_da850", "refclk", &sata_refclk);
-
-int __init da850_register_sata_refclk(int rate)
-{
- int ret;
-
- sata_refclk.rate = rate;
- ret = clk_register(&sata_refclk);
- if (ret)
- return ret;
-
- clkdev_add(&sata_refclk_lookup);
-
- return 0;
-}
-#else
int __init da850_register_sata_refclk(int rate)
{
struct clk *clk;
@@ -1078,7 +1050,6 @@ int __init da850_register_sata_refclk(int rate)
return clk_register_clkdev(clk, "refclk", "ahci_da850");
}
-#endif
static struct resource da850_sata_resources[] = {
{
@@ -103,9 +103,6 @@ int da8xx_register_watchdog(void);
int da8xx_register_usb_phy(void);
int da8xx_register_usb20(unsigned mA, unsigned potpgt);
int da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata);
-int da8xx_register_usb_refclkin(int rate);
-int da8xx_register_usb20_phy_clk(bool use_usb_refclkin);
-int da8xx_register_usb11_phy_clk(bool use_usb_refclkin);
int da8xx_register_usb_phy_clocks(void);
int da850_register_sata_refclk(int rate);
int da8xx_register_emac(void);
@@ -20,11 +20,6 @@
#include <mach/da8xx.h>
#include <mach/irqs.h>
-#ifndef CONFIG_COMMON_CLK
-#include <mach/clock.h>
-#include "clock.h"
-#endif
-
#define DA8XX_USB0_BASE 0x01e00000
#define DA8XX_USB1_BASE 0x01e25000
@@ -87,11 +82,6 @@ static struct platform_device da8xx_usb20_dev = {
.name = "musb-da8xx",
.id = -1,
.dev = {
- /*
- * Setting init_name so that clock lookup will work in
- * usb20_phy_clk_enable() even if this device is not registered.
- */
- .init_name = "musb-da8xx",
.platform_data = &usb_data,
.dma_mask = &usb_dmamask,
.coherent_dma_mask = DMA_BIT_MASK(32),
@@ -140,234 +130,6 @@ int __init da8xx_register_usb11(struct da8xx_ohci_root_hub *pdata)
return platform_device_register(&da8xx_usb11_device);
}
-#ifndef CONFIG_COMMON_CLK
-static struct clk usb_refclkin = {
- .name = "usb_refclkin",
- .set_rate = davinci_simple_set_rate,
-};
-
-static struct clk_lookup usb_refclkin_lookup =
- CLK(NULL, "usb_refclkin", &usb_refclkin);
-
-/**
- * da8xx_register_usb_refclkin - register USB_REFCLKIN clock
- *
- * @rate: The clock rate in Hz
- *
- * This clock is only needed if the board provides an external USB_REFCLKIN
- * signal, in which case it will be used as the parent of usb20_phy_clk and/or
- * usb11_phy_clk.
- */
-int __init da8xx_register_usb_refclkin(int rate)
-{
- int ret;
-
- usb_refclkin.rate = rate;
- ret = clk_register(&usb_refclkin);
- if (ret)
- return ret;
-
- clkdev_add(&usb_refclkin_lookup);
-
- return 0;
-}
-
-static void usb20_phy_clk_enable(struct clk *clk)
-{
- u32 val;
- u32 timeout = 500000; /* 500 msec */
-
- val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- /* The USB 2.O PLL requires that the USB 2.O PSC is enabled as well. */
- davinci_clk_enable(usb20_clk);
-
- /*
- * Turn on the USB 2.0 PHY, but just the PLL, and not OTG. The USB 1.1
- * host may use the PLL clock without USB 2.0 OTG being used.
- */
- val &= ~(CFGCHIP2_RESET | CFGCHIP2_PHYPWRDN);
- val |= CFGCHIP2_PHY_PLLON;
-
- writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- while (--timeout) {
- val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
- if (val & CFGCHIP2_PHYCLKGD)
- goto done;
- udelay(1);
- }
-
- pr_err("Timeout waiting for USB 2.0 PHY clock good\n");
-done:
- davinci_clk_disable(usb20_clk);
-}
-
-static void usb20_phy_clk_disable(struct clk *clk)
-{
- u32 val;
-
- val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
- val |= CFGCHIP2_PHYPWRDN;
- writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-}
-
-static int usb20_phy_clk_set_parent(struct clk *clk, struct clk *parent)
-{
- u32 val;
-
- val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- /* Set the mux depending on the parent clock. */
- if (parent == &usb_refclkin) {
- val &= ~CFGCHIP2_USB2PHYCLKMUX;
- } else if (strcmp(parent->name, "pll0_aux_clk") == 0) {
- val |= CFGCHIP2_USB2PHYCLKMUX;
- } else {
- pr_err("Bad parent on USB 2.0 PHY clock\n");
- return -EINVAL;
- }
-
- /* reference frequency also comes from parent clock */
- val &= ~CFGCHIP2_REFFREQ_MASK;
- switch (clk_get_rate(parent)) {
- case 12000000:
- val |= CFGCHIP2_REFFREQ_12MHZ;
- break;
- case 13000000:
- val |= CFGCHIP2_REFFREQ_13MHZ;
- break;
- case 19200000:
- val |= CFGCHIP2_REFFREQ_19_2MHZ;
- break;
- case 20000000:
- val |= CFGCHIP2_REFFREQ_20MHZ;
- break;
- case 24000000:
- val |= CFGCHIP2_REFFREQ_24MHZ;
- break;
- case 26000000:
- val |= CFGCHIP2_REFFREQ_26MHZ;
- break;
- case 38400000:
- val |= CFGCHIP2_REFFREQ_38_4MHZ;
- break;
- case 40000000:
- val |= CFGCHIP2_REFFREQ_40MHZ;
- break;
- case 48000000:
- val |= CFGCHIP2_REFFREQ_48MHZ;
- break;
- default:
- pr_err("Bad parent clock rate on USB 2.0 PHY clock\n");
- return -EINVAL;
- }
-
- writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- return 0;
-}
-
-static struct clk usb20_phy_clk = {
- .name = "usb0_clk48",
- .clk_enable = usb20_phy_clk_enable,
- .clk_disable = usb20_phy_clk_disable,
- .set_parent = usb20_phy_clk_set_parent,
-};
-
-static struct clk_lookup usb20_phy_clk_lookup =
- CLK("da8xx-usb-phy", "usb0_clk48", &usb20_phy_clk);
-
-/**
- * da8xx_register_usb20_phy_clk - register USB0PHYCLKMUX clock
- *
- * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
- * or "pll0_aux" if false.
- */
-int __init da8xx_register_usb20_phy_clk(bool use_usb_refclkin)
-{
- struct clk *parent;
- int ret;
-
- usb20_clk = clk_get(&da8xx_usb20_dev.dev, "usb20");
- ret = PTR_ERR_OR_ZERO(usb20_clk);
- if (ret)
- return ret;
-
- parent = clk_get(NULL, use_usb_refclkin ? "usb_refclkin" : "pll0_aux");
- ret = PTR_ERR_OR_ZERO(parent);
- if (ret) {
- clk_put(usb20_clk);
- return ret;
- }
-
- usb20_phy_clk.parent = parent;
- ret = clk_register(&usb20_phy_clk);
- if (!ret)
- clkdev_add(&usb20_phy_clk_lookup);
-
- clk_put(parent);
-
- return ret;
-}
-
-static int usb11_phy_clk_set_parent(struct clk *clk, struct clk *parent)
-{
- u32 val;
-
- val = readl(DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- /* Set the USB 1.1 PHY clock mux based on the parent clock. */
- if (parent == &usb20_phy_clk) {
- val &= ~CFGCHIP2_USB1PHYCLKMUX;
- } else if (parent == &usb_refclkin) {
- val |= CFGCHIP2_USB1PHYCLKMUX;
- } else {
- pr_err("Bad parent on USB 1.1 PHY clock\n");
- return -EINVAL;
- }
-
- writel(val, DA8XX_SYSCFG0_VIRT(DA8XX_CFGCHIP2_REG));
-
- return 0;
-}
-
-static struct clk usb11_phy_clk = {
- .name = "usb1_clk48",
- .set_parent = usb11_phy_clk_set_parent,
-};
-
-static struct clk_lookup usb11_phy_clk_lookup =
- CLK("da8xx-usb-phy", "usb1_clk48", &usb11_phy_clk);
-
-/**
- * da8xx_register_usb11_phy_clk - register USB1PHYCLKMUX clock
- *
- * @use_usb_refclkin: Selects the parent clock - either "usb_refclkin" if true
- * or "usb0_clk48" if false.
- */
-int __init da8xx_register_usb11_phy_clk(bool use_usb_refclkin)
-{
- struct clk *parent;
- int ret = 0;
-
- if (use_usb_refclkin)
- parent = clk_get(NULL, "usb_refclkin");
- else
- parent = clk_get(&da8xx_usb_phy.dev, "usb0_clk48");
- if (IS_ERR(parent))
- return PTR_ERR(parent);
-
- usb11_phy_clk.parent = parent;
- ret = clk_register(&usb11_phy_clk);
- if (!ret)
- clkdev_add(&usb11_phy_clk_lookup);
-
- clk_put(parent);
-
- return ret;
-}
-#endif
static struct platform_device da8xx_usb_phy_clks_device = {
.name = "da830-usb-phy-clks",
.id = -1,
This removes the unused legacy USB and SATA clock init code from arch/arm/mach-davinci/{devices,usb}-da8xx}.c. Signed-off-by: David Lechner <david@lechnology.com> Reviewed-by: Sekhar Nori <nsekhar@ti.com> --- v10 changes: - none v9 changes: - none v8 changes: - none v7 changes: - rebased - add davinci prefix to commit message v6 changes: - rebased arch/arm/mach-davinci/devices-da8xx.c | 29 --- arch/arm/mach-davinci/include/mach/da8xx.h | 3 - arch/arm/mach-davinci/usb-da8xx.c | 238 --------------------- 3 files changed, 270 deletions(-)