@@ -180,9 +180,9 @@ config REGULATOR_BCM590XX
BCM590xx PMUs. This will enable support for the software
controllable LDO/Switching regulators.
-config REGULATOR_BD71837
+config REGULATOR_BD718XX
tristate "ROHM BD71837 Power Regulator"
- depends on MFD_BD71837
+ depends on MFD_ROHM_BD718XX
help
This driver supports voltage regulators on ROHM BD71837 PMIC.
This will enable support for the software controllable buck
@@ -27,7 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
-obj-$(CONFIG_REGULATOR_BD71837) += bd71837-regulator.o
+obj-$(CONFIG_REGULATOR_BD718XX) += bd71837-regulator.o
obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o
@@ -7,7 +7,7 @@
#include <linux/gpio.h>
#include <linux/interrupt.h>
#include <linux/kernel.h>
-#include <linux/mfd/bd71837.h>
+#include <linux/mfd/rohm-bd718x7.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/regulator/driver.h>
@@ -490,7 +490,6 @@ struct reg_init {
static int bd71837_probe(struct platform_device *pdev)
{
struct bd71837_pmic *pmic;
- struct bd71837_board *pdata;
struct regulator_config config = { 0 };
struct reg_init pmic_regulator_inits[] = {
{
@@ -558,7 +557,6 @@ static int bd71837_probe(struct platform_device *pdev)
goto err;
}
platform_set_drvdata(pdev, pmic);
- pdata = dev_get_platdata(pmic->mfd->dev);
/* Register LOCK release */
err = regmap_update_bits(pmic->mfd->regmap, BD71837_REG_REGLOCK,
@@ -578,9 +576,6 @@ static int bd71837_probe(struct platform_device *pdev)
desc = &pmic->descs[i];
- if (pdata)
- config.init_data = pdata->init_data[i];
-
config.dev = pdev->dev.parent;
config.driver_data = pmic;
config.regmap = pmic->mfd->regmap;
MFD part for bd71837 was changed during the review. Clean regulator part to match changed MFD: - renamed header file => fix include - remove unused platdata as also type definition was removed - Kconfig option for MFD part was changed => fix depends on clause - Rename Kconfig option for regulators As Kconfig option for regulators gets now used (when dependency to MFD is satisfied) change it so that it won't require new change when support for bd71847 is added. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> --- Please note that the MFD part is still not accepted/applied but I don't expect big (any?) new changes to it. v11 of MFD part was sent for review here: https://lore.kernel.org/lkml/cover.1532946848.git.matti.vaittinen@fi.rohmeurope.com/ drivers/regulator/Kconfig | 4 ++-- drivers/regulator/Makefile | 2 +- drivers/regulator/bd71837-regulator.c | 7 +------ 3 files changed, 4 insertions(+), 9 deletions(-)