diff mbox series

[7/7] arm64: dts: qcom: qcs404: Add PCIe related nodes

Message ID 20190125234509.26419-8-bjorn.andersson@linaro.org (mailing list archive)
State Not Applicable, archived
Headers show
Series QCS404 PCIe PHY and controller | expand

Commit Message

Bjorn Andersson Jan. 25, 2019, 11:45 p.m. UTC
The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to
the platform dtsi and enable them for the EVB with the perst gpio
and analog supplies defined.

Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
---
 arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++
 arch/arm64/boot/dts/qcom/qcs404.dtsi     | 67 ++++++++++++++++++++++++
 2 files changed, 92 insertions(+)

Comments

Stephen Boyd Jan. 30, 2019, 7:24 p.m. UTC | #1
Quoting Bjorn Andersson (2019-01-25 15:45:09)
> @@ -771,6 +788,56 @@
>                                 status = "disabled";
>                         };
>                 };
> +
> +               pcie: pci@10000000 {
> +                       compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
> +                       reg =  <0x10000000 0xf1d

Nitpick: Can you format these like <0x10000000 0xf1d>, <0x10000f20 0xa8>, etc?

> +                               0x10000f20 0xa8
> +                               0x07780000 0x2000
> +                               0x10001000 0x2000>;
> +                       reg-names = "dbi", "elbi", "parf", "config";
> +                       device_type = "pci";
> +                       linux,pci-domain = <0>;
> +                       bus-range = <0x00 0xff>;
> +                       num-lanes = <1>;
> +                       #address-cells = <3>;
> +                       #size-cells = <2>;
> +
> +                       ranges = <0x81000000 0 0          0x10003000 0 0x00010000   /* I/O */

Same for this one? It's nice to know what the size of the cells are.

> +                                 0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
> +
Vinod Koul Feb. 5, 2019, 6:01 a.m. UTC | #2
On 25-01-19, 15:45, Bjorn Andersson wrote:
> The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to
> the platform dtsi and enable them for the EVB with the perst gpio
> and analog supplies defined.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++
>  arch/arm64/boot/dts/qcom/qcs404.dtsi     | 67 ++++++++++++++++++++++++
>  2 files changed, 92 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> index 50b3589c7f15..579ddaf4f5fa 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> @@ -21,6 +21,22 @@
>  	};
>  };
>  
> +&pcie {
> +	status = "ok";
> +
> +	perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&perst_state>;
> +};
> +
> +&pcie_phy {
> +	status = "ok";
> +
> +	vdda-vp-supply = <&vreg_l3_1p05>;
> +	vdda-vph-supply = <&vreg_l5_1p8>;
> +};

I would prefer the patches be split to qcs404 adding PCIe nodes and then
add the board node for EVB... 

> +
>  &remoteproc_adsp {
>  	status = "ok";
>  };
> @@ -137,6 +153,15 @@
>  };
>  
>  &tlmm {
> +	perst_state: perst {
> +		pins = "gpio43";
> +		function = "gpio";
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +		output-low;
> +	};
> +
>  	sdc1_on: sdc1-on {
>  		clk {
>  			pins = "sdc1_clk";
> diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> index 76699435c8bd..7b219865ba7e 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> @@ -3,6 +3,7 @@
>  
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/clock/qcom,gcc-qcs404.h>
> +#include <dt-bindings/gpio/gpio.h>
>  
>  / {
>  	interrupt-parent = <&intc>;
> @@ -377,6 +378,7 @@
>  			compatible = "qcom,gcc-qcs404";
>  			reg = <0x01800000 0x80000>;
>  			#clock-cells = <1>;
> +			#reset-cells = <1>;
>  
>  			assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
>  			assigned-clock-rates = <19200000>;
> @@ -405,6 +407,21 @@
>  			#interrupt-cells = <4>;
>  		};
>  
> +		pcie_phy: phy@7786000 {
> +			compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
> +			reg = <0x07786000 0xb8>;
> +
> +			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
> +			resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
> +				 <&gcc GCC_PCIE_0_PIPE_ARES>;
> +			reset-names = "phy", "pipe";
> +
> +			clock-output-names = "pcie_0_pipe_clk";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
>  		sdcc1: sdcc@7804000 {
>  			compatible = "qcom,sdhci-msm-v5";
>  			reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
> @@ -771,6 +788,56 @@
>  				status = "disabled";
>  			};
>  		};
> +
> +		pcie: pci@10000000 {
> +			compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
> +			reg =  <0x10000000 0xf1d
> +				0x10000f20 0xa8
> +				0x07780000 0x2000
> +				0x10001000 0x2000>;
> +			reg-names = "dbi", "elbi", "parf", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <0>;
> +			bus-range = <0x00 0xff>;
> +			num-lanes = <1>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x81000000 0 0          0x10003000 0 0x00010000   /* I/O */
> +				  0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
> +
> +			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +			clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_0_AUX_CLK>,
> +				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
> +			clock-names = "iface", "aux", "master_bus", "slave_bus";
> +
> +			resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
> +				 <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
> +				 <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
> +				 <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
> +				 <&gcc GCC_PCIE_0_BCR>,
> +				 <&gcc GCC_PCIE_0_AHB_ARES>;
> +			reset-names = "axi_m",
> +				      "axi_s",
> +				      "axi_m_sticky",
> +				      "pipe_sticky",
> +				      "pwr",
> +				      "ahb";
> +
> +			phys = <&pcie_phy>;
> +			phy-names = "pciephy";
> +
> +			status = "disabled";
> +		};
>  	};
>  
>  	timer {
> -- 
> 2.18.0
Niklas Cassel Feb. 8, 2019, 2:50 p.m. UTC | #3
On Fri, Jan 25, 2019 at 03:45:09PM -0800, Bjorn Andersson wrote:
> The QCS404 has a PCIe2 PHY and a Qualcomm PCIe controller, add these to
> the platform dtsi and enable them for the EVB with the perst gpio
> and analog supplies defined.
> 
> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
> ---
>  arch/arm64/boot/dts/qcom/qcs404-evb.dtsi | 25 +++++++++
>  arch/arm64/boot/dts/qcom/qcs404.dtsi     | 67 ++++++++++++++++++++++++
>  2 files changed, 92 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> index 50b3589c7f15..579ddaf4f5fa 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
> @@ -21,6 +21,22 @@
>  	};
>  };
>  
> +&pcie {
> +	status = "ok";
> +
> +	perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
> +
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&perst_state>;
> +};
> +
> +&pcie_phy {
> +	status = "ok";
> +
> +	vdda-vp-supply = <&vreg_l3_1p05>;
> +	vdda-vph-supply = <&vreg_l5_1p8>;
> +};
> +
>  &remoteproc_adsp {
>  	status = "ok";
>  };
> @@ -137,6 +153,15 @@
>  };
>  
>  &tlmm {
> +	perst_state: perst {
> +		pins = "gpio43";
> +		function = "gpio";
> +
> +		drive-strength = <2>;
> +		bias-disable;
> +		output-low;
> +	};
> +
>  	sdc1_on: sdc1-on {
>  		clk {
>  			pins = "sdc1_clk";
> diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> index 76699435c8bd..7b219865ba7e 100644
> --- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
> +++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
> @@ -3,6 +3,7 @@
>  
>  #include <dt-bindings/interrupt-controller/arm-gic.h>
>  #include <dt-bindings/clock/qcom,gcc-qcs404.h>
> +#include <dt-bindings/gpio/gpio.h>
>  
>  / {
>  	interrupt-parent = <&intc>;
> @@ -377,6 +378,7 @@
>  			compatible = "qcom,gcc-qcs404";
>  			reg = <0x01800000 0x80000>;
>  			#clock-cells = <1>;
> +			#reset-cells = <1>;
>  
>  			assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
>  			assigned-clock-rates = <19200000>;
> @@ -405,6 +407,21 @@
>  			#interrupt-cells = <4>;
>  		};
>  
> +		pcie_phy: phy@7786000 {
> +			compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
> +			reg = <0x07786000 0xb8>;
> +
> +			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
> +			resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
> +				 <&gcc GCC_PCIE_0_PIPE_ARES>;
> +			reset-names = "phy", "pipe";
> +
> +			clock-output-names = "pcie_0_pipe_clk";
> +			#phy-cells = <0>;
> +
> +			status = "disabled";
> +		};
> +
>  		sdcc1: sdcc@7804000 {
>  			compatible = "qcom,sdhci-msm-v5";
>  			reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
> @@ -771,6 +788,56 @@
>  				status = "disabled";
>  			};
>  		};
> +
> +		pcie: pci@10000000 {
> +			compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
> +			reg =  <0x10000000 0xf1d
> +				0x10000f20 0xa8
> +				0x07780000 0x2000
> +				0x10001000 0x2000>;
> +			reg-names = "dbi", "elbi", "parf", "config";
> +			device_type = "pci";
> +			linux,pci-domain = <0>;

Since we only have single PCIe controller,
I don't think we need to specify a pci-domain.

With that:
Reviewed-by: Niklas Cassel <niklas.cassel@linaro.org>


> +			bus-range = <0x00 0xff>;
> +			num-lanes = <1>;
> +			#address-cells = <3>;
> +			#size-cells = <2>;
> +
> +			ranges = <0x81000000 0 0          0x10003000 0 0x00010000   /* I/O */
> +				  0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
> +
> +			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
> +			interrupt-names = "msi";
> +			#interrupt-cells = <1>;
> +			interrupt-map-mask = <0 0 0 0x7>;
> +			interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
> +					<0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
> +					<0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
> +					<0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
> +			clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
> +				 <&gcc GCC_PCIE_0_AUX_CLK>,
> +				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
> +				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
> +			clock-names = "iface", "aux", "master_bus", "slave_bus";
> +
> +			resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
> +				 <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
> +				 <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
> +				 <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
> +				 <&gcc GCC_PCIE_0_BCR>,
> +				 <&gcc GCC_PCIE_0_AHB_ARES>;
> +			reset-names = "axi_m",
> +				      "axi_s",
> +				      "axi_m_sticky",
> +				      "pipe_sticky",
> +				      "pwr",
> +				      "ahb";
> +
> +			phys = <&pcie_phy>;
> +			phy-names = "pciephy";
> +
> +			status = "disabled";
> +		};
>  	};
>  
>  	timer {
> -- 
> 2.18.0
>
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
index 50b3589c7f15..579ddaf4f5fa 100644
--- a/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404-evb.dtsi
@@ -21,6 +21,22 @@ 
 	};
 };
 
+&pcie {
+	status = "ok";
+
+	perst-gpio = <&tlmm 43 GPIO_ACTIVE_LOW>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&perst_state>;
+};
+
+&pcie_phy {
+	status = "ok";
+
+	vdda-vp-supply = <&vreg_l3_1p05>;
+	vdda-vph-supply = <&vreg_l5_1p8>;
+};
+
 &remoteproc_adsp {
 	status = "ok";
 };
@@ -137,6 +153,15 @@ 
 };
 
 &tlmm {
+	perst_state: perst {
+		pins = "gpio43";
+		function = "gpio";
+
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
 	sdc1_on: sdc1-on {
 		clk {
 			pins = "sdc1_clk";
diff --git a/arch/arm64/boot/dts/qcom/qcs404.dtsi b/arch/arm64/boot/dts/qcom/qcs404.dtsi
index 76699435c8bd..7b219865ba7e 100644
--- a/arch/arm64/boot/dts/qcom/qcs404.dtsi
+++ b/arch/arm64/boot/dts/qcom/qcs404.dtsi
@@ -3,6 +3,7 @@ 
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/clock/qcom,gcc-qcs404.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	interrupt-parent = <&intc>;
@@ -377,6 +378,7 @@ 
 			compatible = "qcom,gcc-qcs404";
 			reg = <0x01800000 0x80000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 
 			assigned-clocks = <&gcc GCC_APSS_AHB_CLK_SRC>;
 			assigned-clock-rates = <19200000>;
@@ -405,6 +407,21 @@ 
 			#interrupt-cells = <4>;
 		};
 
+		pcie_phy: phy@7786000 {
+			compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy";
+			reg = <0x07786000 0xb8>;
+
+			clocks = <&gcc GCC_PCIE_0_PIPE_CLK>;
+			resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>,
+				 <&gcc GCC_PCIE_0_PIPE_ARES>;
+			reset-names = "phy", "pipe";
+
+			clock-output-names = "pcie_0_pipe_clk";
+			#phy-cells = <0>;
+
+			status = "disabled";
+		};
+
 		sdcc1: sdcc@7804000 {
 			compatible = "qcom,sdhci-msm-v5";
 			reg = <0x07804000 0x1000>, <0x7805000 0x1000>;
@@ -771,6 +788,56 @@ 
 				status = "disabled";
 			};
 		};
+
+		pcie: pci@10000000 {
+			compatible = "qcom,pcie-qcs404", "snps,dw-pcie";
+			reg =  <0x10000000 0xf1d
+				0x10000f20 0xa8
+				0x07780000 0x2000
+				0x10001000 0x2000>;
+			reg-names = "dbi", "elbi", "parf", "config";
+			device_type = "pci";
+			linux,pci-domain = <0>;
+			bus-range = <0x00 0xff>;
+			num-lanes = <1>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			ranges = <0x81000000 0 0          0x10003000 0 0x00010000   /* I/O */
+				  0x82000000 0 0x10013000 0x10013000 0 0x007ed000>; /* memory */
+
+			interrupts = <GIC_SPI 266 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "msi";
+			#interrupt-cells = <1>;
+			interrupt-map-mask = <0 0 0 0x7>;
+			interrupt-map = <0 0 0 1 &intc GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
+					<0 0 0 2 &intc GIC_SPI 224 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
+					<0 0 0 3 &intc GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
+					<0 0 0 4 &intc GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
+			clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
+				 <&gcc GCC_PCIE_0_AUX_CLK>,
+				 <&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
+				 <&gcc GCC_PCIE_0_SLV_AXI_CLK>;
+			clock-names = "iface", "aux", "master_bus", "slave_bus";
+
+			resets = <&gcc GCC_PCIE_0_AXI_MASTER_ARES>,
+				 <&gcc GCC_PCIE_0_AXI_SLAVE_ARES>,
+				 <&gcc GCC_PCIE_0_AXI_MASTER_STICKY_ARES>,
+				 <&gcc GCC_PCIE_0_CORE_STICKY_ARES>,
+				 <&gcc GCC_PCIE_0_BCR>,
+				 <&gcc GCC_PCIE_0_AHB_ARES>;
+			reset-names = "axi_m",
+				      "axi_s",
+				      "axi_m_sticky",
+				      "pipe_sticky",
+				      "pwr",
+				      "ahb";
+
+			phys = <&pcie_phy>;
+			phy-names = "pciephy";
+
+			status = "disabled";
+		};
 	};
 
 	timer {