From patchwork Wed May 6 22:22:57 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Serge Semin X-Patchwork-Id: 11531993 Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 3376615AB for ; Wed, 6 May 2020 22:23:51 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 1F77320753 for ; Wed, 6 May 2020 22:23:51 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1730137AbgEFWXs (ORCPT ); Wed, 6 May 2020 18:23:48 -0400 Received: from mail.baikalelectronics.com ([87.245.175.226]:34218 "EHLO mail.baikalelectronics.ru" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728888AbgEFWXr (ORCPT ); Wed, 6 May 2020 18:23:47 -0400 Received: from localhost (unknown [127.0.0.1]) by mail.baikalelectronics.ru (Postfix) with ESMTP id 00446803080B; Wed, 6 May 2020 22:23:42 +0000 (UTC) X-Virus-Scanned: amavisd-new at baikalelectronics.ru Received: from mail.baikalelectronics.ru ([127.0.0.1]) by localhost (mail.baikalelectronics.ru [127.0.0.1]) (amavisd-new, port 10024) with ESMTP id mwQk2fCuheHN; Thu, 7 May 2020 01:23:40 +0300 (MSK) From: Serge Semin To: Thomas Bogendoerfer , Stephen Boyd , Michael Turquette , Rob Herring CC: Serge Semin , Serge Semin , Alexey Malahov , Paul Burton , Ralf Baechle , Arnd Bergmann , , , , Subject: [PATCH v2 1/4] dt-bindings: clk: Add Baikal-T1 CCU PLLs binding Date: Thu, 7 May 2020 01:22:57 +0300 Message-ID: <20200506222300.30895-2-Sergey.Semin@baikalelectronics.ru> In-Reply-To: <20200506222300.30895-1-Sergey.Semin@baikalelectronics.ru> References: <20200306130053.BCBFC803078F@mail.baikalelectronics.ru> <20200506222300.30895-1-Sergey.Semin@baikalelectronics.ru> MIME-Version: 1.0 X-ClientProxiedBy: MAIL.baikal.int (192.168.51.25) To mail (192.168.51.25) Sender: linux-clk-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-clk@vger.kernel.org Baikal-T1 Clocks Control Unit is responsible for transformation of a signal coming from an external oscillator into clocks of various frequencies to propagate them then to the corresponding clocks consumers (either individual IP-blocks or clock domains). In order to create a set of high-frequency clocks the external signal is firstly handled by the embedded into CCU PLLs. So the corresponding dts-node is just a normal clock-provider node with standard set of properties. Note as being part of the Baikal-T1 System Controller its DT node is supposed to be a child the system controller node. Signed-off-by: Serge Semin Cc: Alexey Malahov Cc: Thomas Bogendoerfer Cc: Paul Burton Cc: Ralf Baechle Cc: Arnd Bergmann Cc: linux-mips@vger.kernel.org --- Changelog v2: - Rearrange the SoBs. - Discard comments in the bindings file header. - Add dual GPL/BSD license. - Add spaces around the ASCII-graphics in the binding description. - Remove reference to Documentation/devicetree/bindings/clock/clock-bindings.txt file. - Discard redundant object check against "/schemas/clock/clock.yaml#" schema. - Discard redundant descriptions of the "#clock-cells" property. - Remove "reg" property since from now the clock DT node is supposed to be a child of the syscon-compatible system controller node. - Remove "clock-output-names" property support. - Replace "additionalProperties: false" with "unevaluatedProperties: false". - Lowercase the nodes name in the examples. - Use "clock-controller" node name suffix in the examples. - Remove unnecessary comments in the clocks dt-bindings header file. --- .../bindings/clock/baikal,bt1-ccu-pll.yaml | 127 ++++++++++++++++++ include/dt-bindings/clock/bt1-ccu.h | 16 +++ 2 files changed, 143 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/baikal,bt1-ccu-pll.yaml create mode 100644 include/dt-bindings/clock/bt1-ccu.h diff --git a/Documentation/devicetree/bindings/clock/baikal,bt1-ccu-pll.yaml b/Documentation/devicetree/bindings/clock/baikal,bt1-ccu-pll.yaml new file mode 100644 index 000000000000..571181758ef2 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/baikal,bt1-ccu-pll.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 BAIKAL ELECTRONICS, JSC +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/baikal,bt1-ccu-pll.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Baikal-T1 Clock Control Unit PLL + +maintainers: + - Serge Semin + +description: | + Clocks Control Unit is the core of Baikal-T1 SoC System Controller + responsible for the chip subsystems clocking and resetting. The CCU is + connected with an external fixed rate oscillator, which signal is transformed + into clocks of various frequencies and then propagated to either individual + IP-blocks or to groups of blocks (clock domains). The transformation is done + by means of PLLs and gateable/non-gateable dividers embedded into the CCU. + It's logically divided into the next components: + 1) External oscillator (normally XTAL's 25 MHz crystal oscillator, but + in general can provide any frequency supported by the CCU PLLs). + 2) PLLs clocks generators (PLLs) - described in this binding file. + 3) AXI-bus clock dividers (AXI). + 4) System devices reference clock dividers (SYS). + which are connected with each other as shown on the next figure: + + +---------------+ + | Baikal-T1 CCU | + | +----+------|- MIPS P5600 cores + | +-|PLLs|------|- DDR controller + | | +----+ | + +----+ | | | | | + |XTAL|--|-+ | | +---+-| + +----+ | | | +-|AXI|-|- AXI-bus + | | | +---+-| + | | | | + | | +----+---+-|- APB-bus + | +-------|SYS|-|- Low-speed Devices + | +---+-|- High-speed Devices + +---------------+ + + Each CCU sub-block is represented as a separate dts-node and has an + individual driver to be bound with. + + In order to create signals of wide range frequencies the external oscillator + output is primarily connected to a set of CCU PLLs. There are five PLLs + to create a clock for the MIPS P5600 cores, the embedded DDR controller, + SATA, Ethernet and PCIe domains. The last three domains though named by the + biggest system interfaces in fact include nearly all of the rest SoC + peripherals. Each of the PLLs is based on True Circuits TSMC CLN28HPM core + with an interface wrapper (so called safe PLL' clocks switcher) to simplify + the PLL configuration procedure. The PLLs work as depicted on the next + diagram: + + +--------------------------+ + | | + +-->+---+ +---+ +---+ | +---+ 0|\ + CLKF--->|/NF|--->|PFD|...|VCO|-+->|/OD|--->| | + +---+ +->+---+ +---+ /->+---+ | |--->CLKOUT + CLKOD---------C----------------+ 1| | + +--------C--------------------------->|/ + | | ^ + Rclk-+->+---+ | | + CLKR--->|/NR|-+ | + +---+ | + BYPASS--------------------------------------+ + BWADJ---> + + where Rclk is the reference clock coming from XTAL, NR - reference clock + divider, NF - PLL clock multiplier, OD - VCO output clock divider, CLKOUT - + output clock, BWADJ is the PLL bandwidth adjustment parameter. At this moment + the binding supports the PLL dividers configuration in accordance with a + requested rate, while bypassing and bandwidth adjustment settings can be + added in future if it gets to be necessary. + + The PLLs CLKOUT is then either directly connected with the corresponding + clocks consumer (like P5600 cores or DDR controller) or passed over a CCU + divider to create a signal required for the clock domain. + + The CCU PLL dts-node uses the common clock bindings with no custom + parameters. The list of exported clocks can be found in + 'include/dt-bindings/clock/bt1-ccu.h'. Since CCU PLL is a part of the + Baikal-T1 SoC System Controller its DT node is supposed to be a child of + later one. + +properties: + compatible: + const: baikal,bt1-ccu-pll + + "#clock-cells": + const: 1 + + clocks: + description: External reference clock + maxItems: 1 + + clock-names: + const: ref_clk + +unevaluatedProperties: false + +required: + - compatible + - "#clock-cells" + - clocks + - clock-names + +examples: + # Clock Control Unit PLL node: + - | + clock-controller-pll { + compatible = "baikal,bt1-ccu-pll"; + #clock-cells = <1>; + + clocks = <&clk25m>; + clock-names = "ref_clk"; + }; + # Required external oscillator: + - | + clk25m: clock-oscillator-25m { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + clock-output-names = "clk25m"; + }; +... diff --git a/include/dt-bindings/clock/bt1-ccu.h b/include/dt-bindings/clock/bt1-ccu.h new file mode 100644 index 000000000000..931a4bea67c0 --- /dev/null +++ b/include/dt-bindings/clock/bt1-ccu.h @@ -0,0 +1,16 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Copyright (C) 2020 BAIKAL ELECTRONICS, JSC + * + * Baikal-T1 CCU clock indices + */ +#ifndef __DT_BINDINGS_CLOCK_BT1_CCU_H +#define __DT_BINDINGS_CLOCK_BT1_CCU_H + +#define CCU_CPU_PLL 0 +#define CCU_SATA_PLL 1 +#define CCU_DDR_PLL 2 +#define CCU_PCIE_PLL 3 +#define CCU_ETH_PLL 4 + +#endif /* __DT_BINDINGS_CLOCK_BT1_CCU_H */