| Message ID | 20230530074221.1031011-11-ychuang570808@gmail.com (mailing list archive) |
|---|---|
| State | Not Applicable, archived |
| Headers | show |
| Series | Introduce Nuvoton ma35d1 SoC | expand |
On Tue, 30 May 2023, Jacky Huang wrote: > From: Jacky Huang <ychuang3@nuvoton.com> > > This adds UART and console driver for Nuvoton ma35d1 Soc. > It supports full-duplex communication, FIFO control, and > hardware flow control. > > Signed-off-by: Jacky Huang <ychuang3@nuvoton.com> > --- > drivers/tty/serial/Kconfig | 18 + > drivers/tty/serial/Makefile | 1 + > drivers/tty/serial/ma35d1_serial.c | 801 +++++++++++++++++++++++++++++ > include/uapi/linux/serial_core.h | 3 + > 4 files changed, 823 insertions(+) > create mode 100644 drivers/tty/serial/ma35d1_serial.c > > diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig > index 398e5aac2e77..85ac6fc1ff1d 100644 > --- a/drivers/tty/serial/Kconfig > +++ b/drivers/tty/serial/Kconfig > @@ -1555,6 +1555,24 @@ config SERIAL_SUNPLUS_CONSOLE > you can alter that using a kernel command line option such as > "console=ttySUPx". > > +config SERIAL_NUVOTON_MA35D1 > + tristate "Nuvoton MA35D1 family UART support" > + depends on ARCH_MA35 || COMPILE_TEST > + select SERIAL_CORE > + help > + This driver supports Nuvoton MA35D1 family UART ports. If you would > + like to use them, you must answer Y or M to this option. Note that > + for use as console, it must be included in kernel and not as a > + module > + > +config SERIAL_NUVOTON_MA35D1_CONSOLE > + bool "Console on a Nuvotn MA35D1 family UART port" > + depends on SERIAL_NUVOTON_MA35D1=y > + select SERIAL_CORE_CONSOLE > + help > + Select this options if you'd like to use the UART port0 of the > + Nuvoton MA35D1 family as a console. > + > endmenu > > config SERIAL_MCTRL_GPIO > diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile > index cd9afd9e3018..0e823851c42c 100644 > --- a/drivers/tty/serial/Makefile > +++ b/drivers/tty/serial/Makefile > @@ -93,3 +93,4 @@ obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o > > obj-$(CONFIG_SERIAL_KGDB_NMI) += kgdb_nmi.o > obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o > +obj-$(CONFIG_SERIAL_NUVOTON_MA35D1) += ma35d1_serial.o > diff --git a/drivers/tty/serial/ma35d1_serial.c b/drivers/tty/serial/ma35d1_serial.c > new file mode 100644 > index 000000000000..c0a8c1e4ca0e > --- /dev/null > +++ b/drivers/tty/serial/ma35d1_serial.c > @@ -0,0 +1,801 @@ > +// SPDX-License-Identifier: GPL-2.0+ > +/* > + * MA35D1 serial driver > + * Copyright (C) 2023 Nuvoton Technology Corp. > + */ > + > +#include <linux/bitfield.h> > +#include <linux/clk.h> > +#include <linux/delay.h> > +#include <linux/of.h> > +#include <linux/of_platform.h> > +#include <linux/serial_core.h> > +#include <linux/slab.h> > +#include <linux/tty_flip.h> > +#include <linux/units.h> > + > +#define MA35_UART_NR 17 > + > +#define MA35_RBR_REG 0x00 > +#define MA35_THR_REG 0x00 > +#define MA35_IER_REG 0x04 > +#define MA35_FCR_REG 0x08 > +#define MA35_LCR_REG 0x0C > +#define MA35_MCR_REG 0x10 > +#define MA35_MSR_REG 0x14 > +#define MA35_FSR_REG 0x18 > +#define MA35_ISR_REG 0x1C > +#define MA35_TOR_REG 0x20 > +#define MA35_BAUD_REG 0x24 > +#define MA35_ALTCTL_REG 0x2C > +#define MA35_FUN_SEL_REG 0x30 > +#define MA35_WKCTL_REG 0x40 > +#define MA35_WKSTS_REG 0x44 > + > +/* MA35_IER_REG - Interrupt Enable Register */ > +#define MA35_IER_RDA_IEN BIT(0) /* RBR Available Interrupt Enable */ > +#define MA35_IER_THRE_IEN BIT(1) /* THR Empty Interrupt Enable */ > +#define MA35_IER_RLS_IEN BIT(2) /* RX Line Status Interrupt Enable */ > +#define MA35_IER_RTO_IEN BIT(4) /* RX Time-out Interrupt Enable */ > +#define MA35_IER_BUFERR_IEN BIT(5) /* Buffer Error Interrupt Enable */ > +#define MA35_IER_TIME_OUT_EN BIT(11) /* RX Buffer Time-out Counter Enable */ > +#define MA35_IER_AUTO_RTS BIT(12) /* nRTS Auto-flow Control Enable */ > +#define MA35_IER_AUTO_CTS BIT(13) /* nCTS Auto-flow Control Enable */ > + > +/* MA35_FCR_REG - FIFO Control Register */ > +#define MA35_FCR_RFR BIT(1) /* RX Field Software Reset */ > +#define MA35_FCR_TFR BIT(2) /* TX Field Software Reset */ > +#define MA35_FCR_RFITL_MASK GENMASK(7, 4) /* RX FIFO Interrupt Trigger Level */ > +#define MA35_FCR_RFITL_1BYTE FIELD_PREP(MA35_FCR_RFITL_MASK, 0) > +#define MA35_FCR_RFITL_4BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 1) > +#define MA35_FCR_RFITL_8BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 2) > +#define MA35_FCR_RFITL_14BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 3) > +#define MA35_FCR_RFITL_30BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 4) > +#define MA35_FCR_RTSTL_MASK GENMASK(19, 16) /* nRTS Trigger Level */ > +#define MA35_FCR_RTSTL_1BYTE FIELD_PREP(MA35_FCR_RTSTL_MASK, 0) > +#define MA35_FCR_RTSTL_4BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 1) > +#define MA35_FCR_RTSTL_8BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 2) > +#define MA35_FCR_RTSTL_14BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 3) > +#define MA35_FCR_RTSTLL_30BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 4) > + > +/* MA35_LCR_REG - Line Control Register */ > +#define MA35_LCR_NSB BIT(2) /* Number of “STOP Bit” */ > +#define MA35_LCR_PBE BIT(3) /* Parity Bit Enable */ > +#define MA35_LCR_EPE BIT(4) /* Even Parity Enable */ > +#define MA35_LCR_SPE BIT(5) /* Stick Parity Enable */ > +#define MA35_LCR_BREAK BIT(6) /* Break Control */ > +#define MA35_LCR_WLS_MASK GENMASK(1, 0) /* Word Length Selection */ > +#define MA35_LCR_WLS_5BITS FIELD_PREP(MA35_LCR_WLS_MASK, 0) > +#define MA35_LCR_WLS_6BITS FIELD_PREP(MA35_LCR_WLS_MASK, 1) > +#define MA35_LCR_WLS_7BITS FIELD_PREP(MA35_LCR_WLS_MASK, 2) > +#define MA35_LCR_WLS_8BITS FIELD_PREP(MA35_LCR_WLS_MASK, 3) > + > +/* MA35_MCR_REG - Modem Control Register */ > +#define MA35_MCR_RTS_CTRL BIT(1) /* nRTS Signal Control */ > +#define MA35_MCR_RTSACTLV BIT(9) /* nRTS Pin Active Level */ > +#define MA35_MCR_RTSSTS BIT(13) /* nRTS Pin Status (Read Only) */ > + > +/* MA35_MSR_REG - Modem Status Register */ > +#define MA35_MSR_CTSDETF BIT(0) /* Detect nCTS State Change Flag */ > +#define MA35_MSR_CTSSTS BIT(4) /* nCTS Pin Status (Read Only) */ > +#define MA35_MSR_CTSACTLV BIT(8) /* nCTS Pin Active Level */ > + > +/* MA35_FSR_REG - FIFO Status Register */ > +#define MA35_FSR_RX_OVER_IF BIT(0) /* RX Overflow Error Interrupt Flag */ > +#define MA35_FSR_PEF BIT(4) /* Parity Error Flag*/ > +#define MA35_FSR_FEF BIT(5) /* Framing Error Flag */ > +#define MA35_FSR_BIF BIT(6) /* Break Interrupt Flag */ > +#define MA35_FSR_RX_EMPTY BIT(14) /* Receiver FIFO Empty (Read Only) */ > +#define MA35_FSR_RX_FULL BIT(15) /* Receiver FIFO Full (Read Only) */ > +#define MA35_FSR_TX_EMPTY BIT(22) /* Transmitter FIFO Empty (Read Only) */ > +#define MA35_FSR_TX_FULL BIT(23) /* Transmitter FIFO Full (Read Only) */ > +#define MA35_FSR_TX_OVER_IF BIT(24) /* TX Overflow Error Interrupt Flag */ > +#define MA35_FSR_TE_FLAG BIT(28) /* Transmitter Empty Flag (Read Only) */ > +#define MA35_FSR_RXPTR_MSK GENMASK(13, 8) /* TX FIFO Pointer mask */ > +#define MA35_FSR_TXPTR_MSK GENMASK(21, 16) /* RX FIFO Pointer mask */ > + > +/* MA35_ISR_REG - Interrupt Status Register */ > +#define MA35_ISR_RDA_IF BIT(0) /* RBR Available Interrupt Flag */ > +#define MA35_ISR_THRE_IF BIT(1) /* THR Empty Interrupt Flag */ > +#define MA35_ISR_RLSIF BIT(2) /* Receive Line Interrupt Flag */ > +#define MA35_ISR_MODEMIF BIT(3) /* MODEM Interrupt Flag */ > +#define MA35_ISR_RXTO_IF BIT(4) /* RX Time-out Interrupt Flag */ > +#define MA35_ISR_BUFEIF BIT(5) /* Buffer Error Interrupt Flag */ > +#define MA35_ISR_WK_IF BIT(6) /* UART Wake-up Interrupt Flag */ > +#define MA35_ISR_RDAINT BIT(8) /* RBR Available Interrupt Indicator */ > +#define MA35_ISR_THRE_INT BIT(9) /* THR Empty Interrupt Indicator */ > +#define MA35_ISR_ALL 0xFFFFFFFF > + > +/* MA35_BAUD_REG - Baud Rate Divider Register */ > +#define MA35_BAUD_MODE_MASK GENMASK(29, 28) > +#define MA35_BAUD_MODE0 FIELD_PREP(MA35_BAUD_MODE_MASK, 0) > +#define MA35_BAUD_MODE1 FIELD_PREP(MA35_BAUD_MODE_MASK, 2) > +#define MA35_BAUD_MODE2 FIELD_PREP(MA35_BAUD_MODE_MASK, 3) > +#define MA35_BAUD_MASK GENMASK(15, 0) > + > +/* MA35_ALTCTL_REG - Alternate Control/Status Register */ > +#define MA35_ALTCTL_RS485AUD BIT(10) /* RS-485 Auto Direction Function */ > + > +/* MA35_FUN_SEL_REG - Function Select Register */ > +#define MA35_FUN_SEL_MASK GENMASK(2, 0) > +#define MA35_FUN_SEL_UART FIELD_PREP(MA35_FUN_SEL_MASK, 0) > +#define MA35_FUN_SEL_RS485 FIELD_PREP(MA35_FUN_SEL_MASK, 3) > + > +/* The constrain for MA35D1 UART baud rate divider */ > +#define MA35_BAUD_DIV_MAX 0xFFFF > +#define MA35_BAUD_DIV_MIN 11 > + > +/* UART FIFO depth */ > +#define MA35_UART_FIFO_DEPTH 32 > +/* UART console clock */ > +#define MA35_UART_CONSOLE_CLK (24 * HZ_PER_MHZ) > +/* UART register ioremap size */ > +#define MA35_UART_REG_SIZE 0x100 > +/* Rx Timeout */ > +#define MA35_UART_RX_TOUT 0x40 > + > +#define MA35_ISR_IF_CHECK (MA35_ISR_RDA_IF | MA35_ISR_RXTO_IF | \ > + MA35_ISR_THRE_INT | MA35_ISR_BUFEIF) > + > +static struct uart_driver ma35d1serial_reg; > + > +struct uart_ma35d1_port { > + struct uart_port port; > + struct clk *clk; > + u16 capabilities; /* port capabilities */ > + u8 ier; > + u8 lcr; > + u8 mcr; > + u32 baud_rate; > + u32 console_baud_rate; > + u32 console_line; > + u32 console_int; > +}; > + > +static struct uart_ma35d1_port ma35d1serial_ports[MA35_UART_NR]; > + > +static struct uart_ma35d1_port *to_ma35d1_uart_port(struct uart_port *uart) > +{ > + return container_of(uart, struct uart_ma35d1_port, port); > +} > + > +static u32 serial_in(struct uart_ma35d1_port *p, u32 offset) > +{ > + return readl_relaxed(p->port.membase + offset); > +} > + > +static void serial_out(struct uart_ma35d1_port *p, u32 offset, u32 value) > +{ > + writel_relaxed(value, p->port.membase + offset); > +} > + > +static void __stop_tx(struct uart_ma35d1_port *p) > +{ > + u32 ier; > + > + ier = serial_in(p, MA35_IER_REG); > + if (ier & MA35_IER_THRE_IEN) > + serial_out(p, MA35_IER_REG, ier & ~MA35_IER_THRE_IEN); > +} > + > +static void ma35d1serial_stop_tx(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + > + __stop_tx(up); > +} > + > +static void transmit_chars(struct uart_ma35d1_port *up) > +{ > + u32 count; > + u8 ch; > + > + if (uart_tx_stopped(&up->port)) { > + ma35d1serial_stop_tx(&up->port); > + return; > + } > + count = MA35_UART_FIFO_DEPTH - FIELD_GET(MA35_FSR_TXPTR_MSK, > + serial_in(up, MA35_FSR_REG)); > + uart_port_tx_limited(&up->port, ch, count, > + !(serial_in(up, MA35_FSR_REG) & MA35_FSR_TX_FULL), > + serial_out(up, MA35_THR_REG, ch), > + ({})); > +} > + > +static void ma35d1serial_start_tx(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + u32 ier; > + > + ier = serial_in(up, MA35_IER_REG); > + serial_out(up, MA35_IER_REG, ier & ~MA35_IER_THRE_IEN); > + transmit_chars(up); > + serial_out(up, MA35_IER_REG, ier | MA35_IER_THRE_IEN); > +} > + > +static void ma35d1serial_stop_rx(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + > + serial_out(up, MA35_IER_REG, serial_in(up, MA35_IER_REG) & ~MA35_IER_RDA_IEN); > +} > + > +static void receive_chars(struct uart_ma35d1_port *up) > +{ > + u8 ch, flag; > + u32 fsr; > + int max_count = 256; > + > + fsr = serial_in(up, MA35_FSR_REG); > + do { > + flag = TTY_NORMAL; > + up->port.icount.rx++; > + > + if (unlikely(fsr & (MA35_FSR_BIF | MA35_FSR_FEF | > + MA35_FSR_PEF | MA35_FSR_RX_OVER_IF))) { > + if (fsr & MA35_FSR_BIF) { > + up->port.icount.brk++; > + if (uart_handle_break(&up->port)) > + continue; > + } > + if (fsr & MA35_FSR_FEF) > + up->port.icount.frame++; > + if (fsr & MA35_FSR_PEF) > + up->port.icount.parity++; > + if (fsr & MA35_FSR_RX_OVER_IF) > + up->port.icount.overrun++; > + > + serial_out(up, MA35_FSR_REG, > + fsr & (MA35_FSR_BIF | MA35_FSR_FEF | > + MA35_FSR_PEF | MA35_FSR_RX_OVER_IF)); > + if (fsr & MA35_FSR_BIF) > + flag = TTY_BREAK; > + else if (fsr & MA35_FSR_PEF) > + flag = TTY_PARITY; > + else if (fsr & MA35_FSR_FEF) > + flag = TTY_FRAME; > + } > + > + ch = serial_in(up, MA35_RBR_REG); > + if (uart_handle_sysrq_char(&up->port, ch)) > + continue; > + > + spin_lock(&up->port.lock); > + uart_insert_char(&up->port, fsr, MA35_FSR_RX_OVER_IF, ch, flag); > + spin_unlock(&up->port.lock); > + > + fsr = serial_in(up, MA35_FSR_REG); > + } while (!(fsr & MA35_FSR_RX_EMPTY) && (max_count-- > 0)); > + > + spin_lock(&up->port.lock); > + tty_flip_buffer_push(&up->port.state->port); > + spin_unlock(&up->port.lock); > +} > + > +static irqreturn_t ma35d1serial_interrupt(int irq, void *dev_id) > +{ > + struct uart_port *port = dev_id; > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + u32 isr, fsr; > + > + isr = serial_in(up, MA35_ISR_REG); > + fsr = serial_in(up, MA35_FSR_REG); > + > + if (!(isr & MA35_ISR_IF_CHECK)) > + return IRQ_NONE; > + > + if (isr & (MA35_ISR_RDA_IF | MA35_ISR_RXTO_IF)) > + receive_chars(up); > + if (isr & MA35_ISR_THRE_INT) > + transmit_chars(up); > + if (fsr & MA35_FSR_TX_OVER_IF) > + serial_out(up, MA35_FSR_REG, MA35_FSR_TX_OVER_IF); > + > + return IRQ_HANDLED; > +} > + > +static u32 ma35d1serial_tx_empty(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + u32 fsr; > + > + fsr = serial_in(up, MA35_FSR_REG); > + return (fsr & (MA35_FSR_TE_FLAG | MA35_FSR_TX_EMPTY)) == > + (MA35_FSR_TE_FLAG | MA35_FSR_TX_EMPTY) ? TIOCSER_TEMT : 0; > +} > + > +static u32 ma35d1serial_get_mctrl(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + u32 status; > + u32 ret = 0; > + > + status = serial_in(up, MA35_MSR_REG); > + if (!(status & MA35_MSR_CTSSTS)) > + ret |= TIOCM_CTS; > + return ret; > +} > + > +static void ma35d1serial_set_mctrl(struct uart_port *port, u32 mctrl) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + u32 mcr; > + u32 ier; > + > + mcr = serial_in(up, MA35_MCR_REG); > + mcr &= ~MA35_MCR_RTS_CTRL; > + > + if (mctrl & TIOCM_RTS) > + mcr |= MA35_MCR_RTSACTLV; > + else > + mcr &= ~MA35_MCR_RTSACTLV; > + > + if (up->mcr & UART_MCR_AFE) { > + serial_out(up, MA35_IER_REG, (serial_in(up, MA35_IER_REG) | > + MA35_IER_AUTO_RTS | > + MA35_IER_AUTO_CTS)); > + up->port.flags |= UPF_HARD_FLOW; > + } else { > + ier = serial_in(up, MA35_IER_REG); > + ier &= ~(MA35_IER_AUTO_RTS | MA35_IER_AUTO_CTS); > + serial_out(up, MA35_IER_REG, ier); > + up->port.flags &= ~UPF_HARD_FLOW; > + } > + serial_out(up, MA35_MSR_REG, (serial_in(up, MA35_MSR_REG) | > + MA35_MSR_CTSACTLV)); > + serial_out(up, MA35_MCR_REG, mcr); > +} > + > +static void ma35d1serial_break_ctl(struct uart_port *port, int break_state) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + unsigned long flags; > + u32 lcr; > + > + spin_lock_irqsave(&up->port.lock, flags); > + lcr = serial_in(up, MA35_LCR_REG); > + if (break_state != 0) > + lcr |= MA35_LCR_BREAK; > + else > + lcr &= ~MA35_LCR_BREAK; > + serial_out(up, MA35_LCR_REG, lcr); > + spin_unlock_irqrestore(&up->port.lock, flags); > +} > + > +static int ma35d1serial_startup(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + int retval; > + > + /* Reset FIFO */ > + serial_out(up, MA35_FCR_REG, MA35_FCR_TFR | MA35_FCR_RFR); > + > + /* Clear pending interrupts */ > + serial_out(up, MA35_ISR_REG, MA35_ISR_ALL); > + > + retval = request_irq(port->irq, ma35d1serial_interrupt, 0, > + dev_name(port->dev), port); > + if (retval) { > + dev_err(up->port.dev, "request irq failed.\n"); > + return retval; > + } > + > + serial_out(up, MA35_FCR_REG, serial_in(up, MA35_FCR_REG) | > + MA35_FCR_RFITL_4BYTES | MA35_FCR_RTSTL_8BYTES); > + serial_out(up, MA35_LCR_REG, MA35_LCR_WLS_8BITS); > + serial_out(up, MA35_TOR_REG, MA35_UART_RX_TOUT); > + serial_out(up, MA35_IER_REG, MA35_IER_RTO_IEN | MA35_IER_RDA_IEN | > + MA35_IER_TIME_OUT_EN | MA35_IER_BUFERR_IEN); > + return 0; > +} > + > +static void ma35d1serial_shutdown(struct uart_port *port) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + > + serial_out(up, MA35_IER_REG, 0); > + free_irq(port->irq, port); > +} > + > +static void ma35d1serial_set_termios(struct uart_port *port, > + struct ktermios *termios, > + const struct ktermios *old) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + u32 lcr = 0; > + unsigned long flags; > + u32 baud, quot; > + > + lcr = UART_LCR_WLEN(tty_get_char_size(termios->c_cflag)); > + > + if (termios->c_cflag & CSTOPB) > + lcr |= MA35_LCR_NSB; > + if (termios->c_cflag & PARENB) > + lcr |= MA35_LCR_PBE; > + if (!(termios->c_cflag & PARODD)) > + lcr |= MA35_LCR_EPE; > + if (termios->c_cflag & CMSPAR) > + lcr |= MA35_LCR_SPE; > + > + baud = uart_get_baud_rate(port, termios, old, > + port->uartclk / MA35_BAUD_DIV_MAX, > + port->uartclk / MA35_BAUD_DIV_MIN); > + > + /* MA35D1 UART baud rate equation: baudrate = UART_CLK / (quot + 2) */ > + quot = (port->uartclk / baud) - 2; > + > + /* > + * Ok, we're now changing the port state. Do it with > + * interrupts disabled. > + */ > + spin_lock_irqsave(&up->port.lock, flags); > + > + up->port.read_status_mask = MA35_FSR_RX_OVER_IF; > + if (termios->c_iflag & INPCK) > + up->port.read_status_mask |= MA35_FSR_FEF | MA35_FSR_PEF; > + if (termios->c_iflag & (BRKINT | PARMRK)) > + up->port.read_status_mask |= MA35_FSR_BIF; > + > + /* Characteres to ignore */ > + up->port.ignore_status_mask = 0; > + if (termios->c_iflag & IGNPAR) > + up->port.ignore_status_mask |= MA35_FSR_FEF | MA35_FSR_PEF; > + if (termios->c_iflag & IGNBRK) { > + up->port.ignore_status_mask |= MA35_FSR_BIF; > + /* > + * If we're ignoring parity and break indicators, > + * ignore overruns too (for real raw support). > + */ > + if (termios->c_iflag & IGNPAR) > + up->port.ignore_status_mask |= MA35_FSR_RX_OVER_IF; > + } > + if (termios->c_cflag & CRTSCTS) > + up->mcr |= UART_MCR_AFE; > + else > + up->mcr &= ~UART_MCR_AFE; > + > + uart_update_timeout(port, termios->c_cflag, baud); > + > + ma35d1serial_set_mctrl(&up->port, up->port.mctrl); > + > + serial_out(up, MA35_BAUD_REG, MA35_BAUD_MODE2 | FIELD_PREP(MA35_BAUD_MASK, quot)); > + > + serial_out(up, MA35_LCR_REG, lcr); > + > + spin_unlock_irqrestore(&up->port.lock, flags); > +} > + > +static const char *ma35d1serial_type(struct uart_port *port) > +{ > + return port->type == PORT_MA35 ? "ma35d1-uart" : NULL; > +} > + > +static void ma35d1serial_config_port(struct uart_port *port, int flags) > +{ > + if (flags & UART_CONFIG_TYPE) > + port->type = PORT_MA35; > +} > + > +static int ma35d1serial_verify_port(struct uart_port *port, struct serial_struct *ser) > +{ > + if (port->type != PORT_UNKNOWN && ser->type != PORT_MA35) > + return -EINVAL; > + > + return 0; > +} > + > +static const struct uart_ops ma35d1serial_ops = { > + .tx_empty = ma35d1serial_tx_empty, > + .set_mctrl = ma35d1serial_set_mctrl, > + .get_mctrl = ma35d1serial_get_mctrl, > + .stop_tx = ma35d1serial_stop_tx, > + .start_tx = ma35d1serial_start_tx, > + .stop_rx = ma35d1serial_stop_rx, > + .break_ctl = ma35d1serial_break_ctl, > + .startup = ma35d1serial_startup, > + .shutdown = ma35d1serial_shutdown, > + .set_termios = ma35d1serial_set_termios, > + .type = ma35d1serial_type, > + .config_port = ma35d1serial_config_port, > + .verify_port = ma35d1serial_verify_port, > +}; > + > +static const struct of_device_id ma35d1_serial_of_match[] = { > + { .compatible = "nuvoton,ma35d1-uart" }, > + {}, > +}; > +MODULE_DEVICE_TABLE(of, ma35d1_serial_of_match); > + > +#ifdef CONFIG_SERIAL_NUVOTON_MA35D1_CONSOLE > + > +static struct device_node *ma35d1serial_uart_nodes[MA35_UART_NR]; > + > +static void wait_for_xmitr(struct uart_ma35d1_port *up) > +{ > + unsigned int tmout; > + > + /* Wait up to 10ms for the character(s) to be sent. */ > + tmout = 10000; > + while (--tmout) { > + if (serial_in(up, MA35_FSR_REG) & MA35_FSR_TX_EMPTY) > + break; > + udelay(1); > + } > +} > + > +static void ma35d1serial_console_putchar(struct uart_port *port, unsigned char ch) > +{ > + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); > + > + wait_for_xmitr(up); > + serial_out(up, MA35_THR_REG, ch); > +} > + > +/* > + * Print a string to the serial port trying not to disturb > + * any possible real use of the port... > + * > + * The console_lock must be held when we get here. > + */ > +static void ma35d1serial_console_write(struct console *co, const char *s, u32 count) > +{ > + struct uart_ma35d1_port *up = &ma35d1serial_ports[co->index]; > + unsigned long flags; > + u32 ier; > + > + spin_lock_irqsave(&up->port.lock, flags); This lacks the oops_in_progress trickery the other drivers do? Although I think there really should be uart_console_write_lock(uart_port *up, unsigned long *flags, bool *locked) and uart_console_write_unlock() helpers in serial core for this task.
Dear Ilpo, On 2023/5/30 下午 04:33, Ilpo Järvinen wrote: > On Tue, 30 May 2023, Jacky Huang wrote: > >> From: Jacky Huang <ychuang3@nuvoton.com> >> >> This adds UART and console driver for Nuvoton ma35d1 Soc. >> It supports full-duplex communication, FIFO control, and >> hardware flow control. >> >> Signed-off-by: Jacky Huang <ychuang3@nuvoton.com> >> --- >> drivers/tty/serial/Kconfig | 18 + >> drivers/tty/serial/Makefile | 1 + >> drivers/tty/serial/ma35d1_serial.c | 801 +++++++++++++++++++++++++++++ >> include/uapi/linux/serial_core.h | 3 + >> 4 files changed, 823 insertions(+) >> create mode 100644 drivers/tty/serial/ma35d1_serial.c >> >> diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig >> index 398e5aac2e77..85ac6fc1ff1d 100644 >> --- a/drivers/tty/serial/Kconfig >> +++ b/drivers/tty/serial/Kconfig >> @@ -1555,6 +1555,24 @@ config SERIAL_SUNPLUS_CONSOLE >> you can alter that using a kernel command line option such as >> "console=ttySUPx". >> >> +config SERIAL_NUVOTON_MA35D1 >> + tristate "Nuvoton MA35D1 family UART support" >> + depends on ARCH_MA35 || COMPILE_TEST >> + select SERIAL_CORE >> + help >> + This driver supports Nuvoton MA35D1 family UART ports. If you would >> + like to use them, you must answer Y or M to this option. Note that >> + for use as console, it must be included in kernel and not as a >> + module >> + >> +config SERIAL_NUVOTON_MA35D1_CONSOLE >> + bool "Console on a Nuvotn MA35D1 family UART port" >> + depends on SERIAL_NUVOTON_MA35D1=y >> + select SERIAL_CORE_CONSOLE >> + help >> + Select this options if you'd like to use the UART port0 of the >> + Nuvoton MA35D1 family as a console. >> + >> endmenu >> >> config SERIAL_MCTRL_GPIO >> diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile >> index cd9afd9e3018..0e823851c42c 100644 >> --- a/drivers/tty/serial/Makefile >> +++ b/drivers/tty/serial/Makefile >> @@ -93,3 +93,4 @@ obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o >> >> obj-$(CONFIG_SERIAL_KGDB_NMI) += kgdb_nmi.o >> obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o >> +obj-$(CONFIG_SERIAL_NUVOTON_MA35D1) += ma35d1_serial.o >> diff --git a/drivers/tty/serial/ma35d1_serial.c b/drivers/tty/serial/ma35d1_serial.c >> new file mode 100644 >> index 000000000000..c0a8c1e4ca0e >> --- /dev/null >> +++ b/drivers/tty/serial/ma35d1_serial.c >> @@ -0,0 +1,801 @@ >> +// SPDX-License-Identifier: GPL-2.0+ >> +/* >> + * MA35D1 serial driver >> + * Copyright (C) 2023 Nuvoton Technology Corp. >> + */ >> + >> +#include <linux/bitfield.h> >> +#include <linux/clk.h> >> +#include <linux/delay.h> >> +#include <linux/of.h> >> +#include <linux/of_platform.h> >> +#include <linux/serial_core.h> >> +#include <linux/slab.h> >> +#include <linux/tty_flip.h> >> +#include <linux/units.h> >> + >> +#define MA35_UART_NR 17 >> + >> +#define MA35_RBR_REG 0x00 >> +#define MA35_THR_REG 0x00 >> +#define MA35_IER_REG 0x04 >> +#define MA35_FCR_REG 0x08 >> +#define MA35_LCR_REG 0x0C >> +#define MA35_MCR_REG 0x10 >> +#define MA35_MSR_REG 0x14 >> +#define MA35_FSR_REG 0x18 >> +#define MA35_ISR_REG 0x1C >> +#define MA35_TOR_REG 0x20 >> +#define MA35_BAUD_REG 0x24 >> +#define MA35_ALTCTL_REG 0x2C >> +#define MA35_FUN_SEL_REG 0x30 >> +#define MA35_WKCTL_REG 0x40 >> +#define MA35_WKSTS_REG 0x44 >> + >> +/* MA35_IER_REG - Interrupt Enable Register */ >> +#define MA35_IER_RDA_IEN BIT(0) /* RBR Available Interrupt Enable */ >> +#define MA35_IER_THRE_IEN BIT(1) /* THR Empty Interrupt Enable */ >> +#define MA35_IER_RLS_IEN BIT(2) /* RX Line Status Interrupt Enable */ >> +#define MA35_IER_RTO_IEN BIT(4) /* RX Time-out Interrupt Enable */ >> +#define MA35_IER_BUFERR_IEN BIT(5) /* Buffer Error Interrupt Enable */ >> +#define MA35_IER_TIME_OUT_EN BIT(11) /* RX Buffer Time-out Counter Enable */ >> +#define MA35_IER_AUTO_RTS BIT(12) /* nRTS Auto-flow Control Enable */ >> +#define MA35_IER_AUTO_CTS BIT(13) /* nCTS Auto-flow Control Enable */ >> + >> +/* MA35_FCR_REG - FIFO Control Register */ >> +#define MA35_FCR_RFR BIT(1) /* RX Field Software Reset */ >> +#define MA35_FCR_TFR BIT(2) /* TX Field Software Reset */ >> +#define MA35_FCR_RFITL_MASK GENMASK(7, 4) /* RX FIFO Interrupt Trigger Level */ >> +#define MA35_FCR_RFITL_1BYTE FIELD_PREP(MA35_FCR_RFITL_MASK, 0) >> +#define MA35_FCR_RFITL_4BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 1) >> +#define MA35_FCR_RFITL_8BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 2) >> +#define MA35_FCR_RFITL_14BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 3) >> +#define MA35_FCR_RFITL_30BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 4) >> +#define MA35_FCR_RTSTL_MASK GENMASK(19, 16) /* nRTS Trigger Level */ >> +#define MA35_FCR_RTSTL_1BYTE FIELD_PREP(MA35_FCR_RTSTL_MASK, 0) >> +#define MA35_FCR_RTSTL_4BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 1) >> +#define MA35_FCR_RTSTL_8BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 2) >> +#define MA35_FCR_RTSTL_14BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 3) >> +#define MA35_FCR_RTSTLL_30BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 4) >> + >> +/* MA35_LCR_REG - Line Control Register */ >> +#define MA35_LCR_NSB BIT(2) /* Number of “STOP Bit” */ >> +#define MA35_LCR_PBE BIT(3) /* Parity Bit Enable */ >> +#define MA35_LCR_EPE BIT(4) /* Even Parity Enable */ >> +#define MA35_LCR_SPE BIT(5) /* Stick Parity Enable */ >> +#define MA35_LCR_BREAK BIT(6) /* Break Control */ >> +#define MA35_LCR_WLS_MASK GENMASK(1, 0) /* Word Length Selection */ >> +#define MA35_LCR_WLS_5BITS FIELD_PREP(MA35_LCR_WLS_MASK, 0) >> +#define MA35_LCR_WLS_6BITS FIELD_PREP(MA35_LCR_WLS_MASK, 1) >> +#define MA35_LCR_WLS_7BITS FIELD_PREP(MA35_LCR_WLS_MASK, 2) >> +#define MA35_LCR_WLS_8BITS FIELD_PREP(MA35_LCR_WLS_MASK, 3) >> + >> +/* MA35_MCR_REG - Modem Control Register */ >> +#define MA35_MCR_RTS_CTRL BIT(1) /* nRTS Signal Control */ >> +#define MA35_MCR_RTSACTLV BIT(9) /* nRTS Pin Active Level */ >> +#define MA35_MCR_RTSSTS BIT(13) /* nRTS Pin Status (Read Only) */ >> + >> +/* MA35_MSR_REG - Modem Status Register */ >> +#define MA35_MSR_CTSDETF BIT(0) /* Detect nCTS State Change Flag */ >> +#define MA35_MSR_CTSSTS BIT(4) /* nCTS Pin Status (Read Only) */ >> +#define MA35_MSR_CTSACTLV BIT(8) /* nCTS Pin Active Level */ >> + >> +/* MA35_FSR_REG - FIFO Status Register */ >> +#define MA35_FSR_RX_OVER_IF BIT(0) /* RX Overflow Error Interrupt Flag */ >> +#define MA35_FSR_PEF BIT(4) /* Parity Error Flag*/ >> +#define MA35_FSR_FEF BIT(5) /* Framing Error Flag */ >> +#define MA35_FSR_BIF BIT(6) /* Break Interrupt Flag */ >> +#define MA35_FSR_RX_EMPTY BIT(14) /* Receiver FIFO Empty (Read Only) */ >> +#define MA35_FSR_RX_FULL BIT(15) /* Receiver FIFO Full (Read Only) */ >> +#define MA35_FSR_TX_EMPTY BIT(22) /* Transmitter FIFO Empty (Read Only) */ >> +#define MA35_FSR_TX_FULL BIT(23) /* Transmitter FIFO Full (Read Only) */ >> +#define MA35_FSR_TX_OVER_IF BIT(24) /* TX Overflow Error Interrupt Flag */ >> +#define MA35_FSR_TE_FLAG BIT(28) /* Transmitter Empty Flag (Read Only) */ >> +#define MA35_FSR_RXPTR_MSK GENMASK(13, 8) /* TX FIFO Pointer mask */ >> +#define MA35_FSR_TXPTR_MSK GENMASK(21, 16) /* RX FIFO Pointer mask */ >> + >> +/* MA35_ISR_REG - Interrupt Status Register */ >> +#define MA35_ISR_RDA_IF BIT(0) /* RBR Available Interrupt Flag */ >> +#define MA35_ISR_THRE_IF BIT(1) /* THR Empty Interrupt Flag */ >> +#define MA35_ISR_RLSIF BIT(2) /* Receive Line Interrupt Flag */ >> +#define MA35_ISR_MODEMIF BIT(3) /* MODEM Interrupt Flag */ >> +#define MA35_ISR_RXTO_IF BIT(4) /* RX Time-out Interrupt Flag */ >> +#define MA35_ISR_BUFEIF BIT(5) /* Buffer Error Interrupt Flag */ >> +#define MA35_ISR_WK_IF BIT(6) /* UART Wake-up Interrupt Flag */ >> +#define MA35_ISR_RDAINT BIT(8) /* RBR Available Interrupt Indicator */ >> +#define MA35_ISR_THRE_INT BIT(9) /* THR Empty Interrupt Indicator */ >> +#define MA35_ISR_ALL 0xFFFFFFFF >> + >> +/* MA35_BAUD_REG - Baud Rate Divider Register */ >> +#define MA35_BAUD_MODE_MASK GENMASK(29, 28) >> +#define MA35_BAUD_MODE0 FIELD_PREP(MA35_BAUD_MODE_MASK, 0) >> +#define MA35_BAUD_MODE1 FIELD_PREP(MA35_BAUD_MODE_MASK, 2) >> +#define MA35_BAUD_MODE2 FIELD_PREP(MA35_BAUD_MODE_MASK, 3) >> +#define MA35_BAUD_MASK GENMASK(15, 0) >> + >> +/* MA35_ALTCTL_REG - Alternate Control/Status Register */ >> +#define MA35_ALTCTL_RS485AUD BIT(10) /* RS-485 Auto Direction Function */ >> + >> +/* MA35_FUN_SEL_REG - Function Select Register */ >> +#define MA35_FUN_SEL_MASK GENMASK(2, 0) >> +#define MA35_FUN_SEL_UART FIELD_PREP(MA35_FUN_SEL_MASK, 0) >> +#define MA35_FUN_SEL_RS485 FIELD_PREP(MA35_FUN_SEL_MASK, 3) >> + >> +/* The constrain for MA35D1 UART baud rate divider */ >> +#define MA35_BAUD_DIV_MAX 0xFFFF >> +#define MA35_BAUD_DIV_MIN 11 >> + >> +/* UART FIFO depth */ >> +#define MA35_UART_FIFO_DEPTH 32 >> +/* UART console clock */ >> +#define MA35_UART_CONSOLE_CLK (24 * HZ_PER_MHZ) >> +/* UART register ioremap size */ >> +#define MA35_UART_REG_SIZE 0x100 >> +/* Rx Timeout */ >> +#define MA35_UART_RX_TOUT 0x40 >> + >> +#define MA35_ISR_IF_CHECK (MA35_ISR_RDA_IF | MA35_ISR_RXTO_IF | \ >> + MA35_ISR_THRE_INT | MA35_ISR_BUFEIF) >> + >> +static struct uart_driver ma35d1serial_reg; >> + >> +struct uart_ma35d1_port { >> + struct uart_port port; >> + struct clk *clk; >> + u16 capabilities; /* port capabilities */ >> + u8 ier; >> + u8 lcr; >> + u8 mcr; >> + u32 baud_rate; >> + u32 console_baud_rate; >> + u32 console_line; >> + u32 console_int; >> +}; >> + >> +static struct uart_ma35d1_port ma35d1serial_ports[MA35_UART_NR]; >> + >> +static struct uart_ma35d1_port *to_ma35d1_uart_port(struct uart_port *uart) >> +{ >> + return container_of(uart, struct uart_ma35d1_port, port); >> +} >> + >> +static u32 serial_in(struct uart_ma35d1_port *p, u32 offset) >> +{ >> + return readl_relaxed(p->port.membase + offset); >> +} >> + >> +static void serial_out(struct uart_ma35d1_port *p, u32 offset, u32 value) >> +{ >> + writel_relaxed(value, p->port.membase + offset); >> +} >> + >> +static void __stop_tx(struct uart_ma35d1_port *p) >> +{ >> + u32 ier; >> + >> + ier = serial_in(p, MA35_IER_REG); >> + if (ier & MA35_IER_THRE_IEN) >> + serial_out(p, MA35_IER_REG, ier & ~MA35_IER_THRE_IEN); >> +} >> + >> +static void ma35d1serial_stop_tx(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + >> + __stop_tx(up); >> +} >> + >> +static void transmit_chars(struct uart_ma35d1_port *up) >> +{ >> + u32 count; >> + u8 ch; >> + >> + if (uart_tx_stopped(&up->port)) { >> + ma35d1serial_stop_tx(&up->port); >> + return; >> + } >> + count = MA35_UART_FIFO_DEPTH - FIELD_GET(MA35_FSR_TXPTR_MSK, >> + serial_in(up, MA35_FSR_REG)); >> + uart_port_tx_limited(&up->port, ch, count, >> + !(serial_in(up, MA35_FSR_REG) & MA35_FSR_TX_FULL), >> + serial_out(up, MA35_THR_REG, ch), >> + ({})); >> +} >> + >> +static void ma35d1serial_start_tx(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + u32 ier; >> + >> + ier = serial_in(up, MA35_IER_REG); >> + serial_out(up, MA35_IER_REG, ier & ~MA35_IER_THRE_IEN); >> + transmit_chars(up); >> + serial_out(up, MA35_IER_REG, ier | MA35_IER_THRE_IEN); >> +} >> + >> +static void ma35d1serial_stop_rx(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + >> + serial_out(up, MA35_IER_REG, serial_in(up, MA35_IER_REG) & ~MA35_IER_RDA_IEN); >> +} >> + >> +static void receive_chars(struct uart_ma35d1_port *up) >> +{ >> + u8 ch, flag; >> + u32 fsr; >> + int max_count = 256; >> + >> + fsr = serial_in(up, MA35_FSR_REG); >> + do { >> + flag = TTY_NORMAL; >> + up->port.icount.rx++; >> + >> + if (unlikely(fsr & (MA35_FSR_BIF | MA35_FSR_FEF | >> + MA35_FSR_PEF | MA35_FSR_RX_OVER_IF))) { >> + if (fsr & MA35_FSR_BIF) { >> + up->port.icount.brk++; >> + if (uart_handle_break(&up->port)) >> + continue; >> + } >> + if (fsr & MA35_FSR_FEF) >> + up->port.icount.frame++; >> + if (fsr & MA35_FSR_PEF) >> + up->port.icount.parity++; >> + if (fsr & MA35_FSR_RX_OVER_IF) >> + up->port.icount.overrun++; >> + >> + serial_out(up, MA35_FSR_REG, >> + fsr & (MA35_FSR_BIF | MA35_FSR_FEF | >> + MA35_FSR_PEF | MA35_FSR_RX_OVER_IF)); >> + if (fsr & MA35_FSR_BIF) >> + flag = TTY_BREAK; >> + else if (fsr & MA35_FSR_PEF) >> + flag = TTY_PARITY; >> + else if (fsr & MA35_FSR_FEF) >> + flag = TTY_FRAME; >> + } >> + >> + ch = serial_in(up, MA35_RBR_REG); >> + if (uart_handle_sysrq_char(&up->port, ch)) >> + continue; >> + >> + spin_lock(&up->port.lock); >> + uart_insert_char(&up->port, fsr, MA35_FSR_RX_OVER_IF, ch, flag); >> + spin_unlock(&up->port.lock); >> + >> + fsr = serial_in(up, MA35_FSR_REG); >> + } while (!(fsr & MA35_FSR_RX_EMPTY) && (max_count-- > 0)); >> + >> + spin_lock(&up->port.lock); >> + tty_flip_buffer_push(&up->port.state->port); >> + spin_unlock(&up->port.lock); >> +} >> + >> +static irqreturn_t ma35d1serial_interrupt(int irq, void *dev_id) >> +{ >> + struct uart_port *port = dev_id; >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + u32 isr, fsr; >> + >> + isr = serial_in(up, MA35_ISR_REG); >> + fsr = serial_in(up, MA35_FSR_REG); >> + >> + if (!(isr & MA35_ISR_IF_CHECK)) >> + return IRQ_NONE; >> + >> + if (isr & (MA35_ISR_RDA_IF | MA35_ISR_RXTO_IF)) >> + receive_chars(up); >> + if (isr & MA35_ISR_THRE_INT) >> + transmit_chars(up); >> + if (fsr & MA35_FSR_TX_OVER_IF) >> + serial_out(up, MA35_FSR_REG, MA35_FSR_TX_OVER_IF); >> + >> + return IRQ_HANDLED; >> +} >> + >> +static u32 ma35d1serial_tx_empty(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + u32 fsr; >> + >> + fsr = serial_in(up, MA35_FSR_REG); >> + return (fsr & (MA35_FSR_TE_FLAG | MA35_FSR_TX_EMPTY)) == >> + (MA35_FSR_TE_FLAG | MA35_FSR_TX_EMPTY) ? TIOCSER_TEMT : 0; >> +} >> + >> +static u32 ma35d1serial_get_mctrl(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + u32 status; >> + u32 ret = 0; >> + >> + status = serial_in(up, MA35_MSR_REG); >> + if (!(status & MA35_MSR_CTSSTS)) >> + ret |= TIOCM_CTS; >> + return ret; >> +} >> + >> +static void ma35d1serial_set_mctrl(struct uart_port *port, u32 mctrl) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + u32 mcr; >> + u32 ier; >> + >> + mcr = serial_in(up, MA35_MCR_REG); >> + mcr &= ~MA35_MCR_RTS_CTRL; >> + >> + if (mctrl & TIOCM_RTS) >> + mcr |= MA35_MCR_RTSACTLV; >> + else >> + mcr &= ~MA35_MCR_RTSACTLV; >> + >> + if (up->mcr & UART_MCR_AFE) { >> + serial_out(up, MA35_IER_REG, (serial_in(up, MA35_IER_REG) | >> + MA35_IER_AUTO_RTS | >> + MA35_IER_AUTO_CTS)); >> + up->port.flags |= UPF_HARD_FLOW; >> + } else { >> + ier = serial_in(up, MA35_IER_REG); >> + ier &= ~(MA35_IER_AUTO_RTS | MA35_IER_AUTO_CTS); >> + serial_out(up, MA35_IER_REG, ier); >> + up->port.flags &= ~UPF_HARD_FLOW; >> + } >> + serial_out(up, MA35_MSR_REG, (serial_in(up, MA35_MSR_REG) | >> + MA35_MSR_CTSACTLV)); >> + serial_out(up, MA35_MCR_REG, mcr); >> +} >> + >> +static void ma35d1serial_break_ctl(struct uart_port *port, int break_state) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + unsigned long flags; >> + u32 lcr; >> + >> + spin_lock_irqsave(&up->port.lock, flags); >> + lcr = serial_in(up, MA35_LCR_REG); >> + if (break_state != 0) >> + lcr |= MA35_LCR_BREAK; >> + else >> + lcr &= ~MA35_LCR_BREAK; >> + serial_out(up, MA35_LCR_REG, lcr); >> + spin_unlock_irqrestore(&up->port.lock, flags); >> +} >> + >> +static int ma35d1serial_startup(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + int retval; >> + >> + /* Reset FIFO */ >> + serial_out(up, MA35_FCR_REG, MA35_FCR_TFR | MA35_FCR_RFR); >> + >> + /* Clear pending interrupts */ >> + serial_out(up, MA35_ISR_REG, MA35_ISR_ALL); >> + >> + retval = request_irq(port->irq, ma35d1serial_interrupt, 0, >> + dev_name(port->dev), port); >> + if (retval) { >> + dev_err(up->port.dev, "request irq failed.\n"); >> + return retval; >> + } >> + >> + serial_out(up, MA35_FCR_REG, serial_in(up, MA35_FCR_REG) | >> + MA35_FCR_RFITL_4BYTES | MA35_FCR_RTSTL_8BYTES); >> + serial_out(up, MA35_LCR_REG, MA35_LCR_WLS_8BITS); >> + serial_out(up, MA35_TOR_REG, MA35_UART_RX_TOUT); >> + serial_out(up, MA35_IER_REG, MA35_IER_RTO_IEN | MA35_IER_RDA_IEN | >> + MA35_IER_TIME_OUT_EN | MA35_IER_BUFERR_IEN); >> + return 0; >> +} >> + >> +static void ma35d1serial_shutdown(struct uart_port *port) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + >> + serial_out(up, MA35_IER_REG, 0); >> + free_irq(port->irq, port); >> +} >> + >> +static void ma35d1serial_set_termios(struct uart_port *port, >> + struct ktermios *termios, >> + const struct ktermios *old) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + u32 lcr = 0; >> + unsigned long flags; >> + u32 baud, quot; >> + >> + lcr = UART_LCR_WLEN(tty_get_char_size(termios->c_cflag)); >> + >> + if (termios->c_cflag & CSTOPB) >> + lcr |= MA35_LCR_NSB; >> + if (termios->c_cflag & PARENB) >> + lcr |= MA35_LCR_PBE; >> + if (!(termios->c_cflag & PARODD)) >> + lcr |= MA35_LCR_EPE; >> + if (termios->c_cflag & CMSPAR) >> + lcr |= MA35_LCR_SPE; >> + >> + baud = uart_get_baud_rate(port, termios, old, >> + port->uartclk / MA35_BAUD_DIV_MAX, >> + port->uartclk / MA35_BAUD_DIV_MIN); >> + >> + /* MA35D1 UART baud rate equation: baudrate = UART_CLK / (quot + 2) */ >> + quot = (port->uartclk / baud) - 2; >> + >> + /* >> + * Ok, we're now changing the port state. Do it with >> + * interrupts disabled. >> + */ >> + spin_lock_irqsave(&up->port.lock, flags); >> + >> + up->port.read_status_mask = MA35_FSR_RX_OVER_IF; >> + if (termios->c_iflag & INPCK) >> + up->port.read_status_mask |= MA35_FSR_FEF | MA35_FSR_PEF; >> + if (termios->c_iflag & (BRKINT | PARMRK)) >> + up->port.read_status_mask |= MA35_FSR_BIF; >> + >> + /* Characteres to ignore */ >> + up->port.ignore_status_mask = 0; >> + if (termios->c_iflag & IGNPAR) >> + up->port.ignore_status_mask |= MA35_FSR_FEF | MA35_FSR_PEF; >> + if (termios->c_iflag & IGNBRK) { >> + up->port.ignore_status_mask |= MA35_FSR_BIF; >> + /* >> + * If we're ignoring parity and break indicators, >> + * ignore overruns too (for real raw support). >> + */ >> + if (termios->c_iflag & IGNPAR) >> + up->port.ignore_status_mask |= MA35_FSR_RX_OVER_IF; >> + } >> + if (termios->c_cflag & CRTSCTS) >> + up->mcr |= UART_MCR_AFE; >> + else >> + up->mcr &= ~UART_MCR_AFE; >> + >> + uart_update_timeout(port, termios->c_cflag, baud); >> + >> + ma35d1serial_set_mctrl(&up->port, up->port.mctrl); >> + >> + serial_out(up, MA35_BAUD_REG, MA35_BAUD_MODE2 | FIELD_PREP(MA35_BAUD_MASK, quot)); >> + >> + serial_out(up, MA35_LCR_REG, lcr); >> + >> + spin_unlock_irqrestore(&up->port.lock, flags); >> +} >> + >> +static const char *ma35d1serial_type(struct uart_port *port) >> +{ >> + return port->type == PORT_MA35 ? "ma35d1-uart" : NULL; >> +} >> + >> +static void ma35d1serial_config_port(struct uart_port *port, int flags) >> +{ >> + if (flags & UART_CONFIG_TYPE) >> + port->type = PORT_MA35; >> +} >> + >> +static int ma35d1serial_verify_port(struct uart_port *port, struct serial_struct *ser) >> +{ >> + if (port->type != PORT_UNKNOWN && ser->type != PORT_MA35) >> + return -EINVAL; >> + >> + return 0; >> +} >> + >> +static const struct uart_ops ma35d1serial_ops = { >> + .tx_empty = ma35d1serial_tx_empty, >> + .set_mctrl = ma35d1serial_set_mctrl, >> + .get_mctrl = ma35d1serial_get_mctrl, >> + .stop_tx = ma35d1serial_stop_tx, >> + .start_tx = ma35d1serial_start_tx, >> + .stop_rx = ma35d1serial_stop_rx, >> + .break_ctl = ma35d1serial_break_ctl, >> + .startup = ma35d1serial_startup, >> + .shutdown = ma35d1serial_shutdown, >> + .set_termios = ma35d1serial_set_termios, >> + .type = ma35d1serial_type, >> + .config_port = ma35d1serial_config_port, >> + .verify_port = ma35d1serial_verify_port, >> +}; >> + >> +static const struct of_device_id ma35d1_serial_of_match[] = { >> + { .compatible = "nuvoton,ma35d1-uart" }, >> + {}, >> +}; >> +MODULE_DEVICE_TABLE(of, ma35d1_serial_of_match); >> + >> +#ifdef CONFIG_SERIAL_NUVOTON_MA35D1_CONSOLE >> + >> +static struct device_node *ma35d1serial_uart_nodes[MA35_UART_NR]; >> + >> +static void wait_for_xmitr(struct uart_ma35d1_port *up) >> +{ >> + unsigned int tmout; >> + >> + /* Wait up to 10ms for the character(s) to be sent. */ >> + tmout = 10000; >> + while (--tmout) { >> + if (serial_in(up, MA35_FSR_REG) & MA35_FSR_TX_EMPTY) >> + break; >> + udelay(1); >> + } >> +} >> + >> +static void ma35d1serial_console_putchar(struct uart_port *port, unsigned char ch) >> +{ >> + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); >> + >> + wait_for_xmitr(up); >> + serial_out(up, MA35_THR_REG, ch); >> +} >> + >> +/* >> + * Print a string to the serial port trying not to disturb >> + * any possible real use of the port... >> + * >> + * The console_lock must be held when we get here. >> + */ >> +static void ma35d1serial_console_write(struct console *co, const char *s, u32 count) >> +{ >> + struct uart_ma35d1_port *up = &ma35d1serial_ports[co->index]; >> + unsigned long flags; >> + u32 ier; >> + >> + spin_lock_irqsave(&up->port.lock, flags); > This lacks the oops_in_progress trickery the other drivers do? > > Although I think there really should be uart_console_write_lock(uart_port > *up, unsigned long *flags, bool *locked) and uart_console_write_unlock() > helpers in serial core for this task. > Okay, I will add the 'oops_in_progress' check to it. Best regards, Jacky Huang
diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig index 398e5aac2e77..85ac6fc1ff1d 100644 --- a/drivers/tty/serial/Kconfig +++ b/drivers/tty/serial/Kconfig @@ -1555,6 +1555,24 @@ config SERIAL_SUNPLUS_CONSOLE you can alter that using a kernel command line option such as "console=ttySUPx". +config SERIAL_NUVOTON_MA35D1 + tristate "Nuvoton MA35D1 family UART support" + depends on ARCH_MA35 || COMPILE_TEST + select SERIAL_CORE + help + This driver supports Nuvoton MA35D1 family UART ports. If you would + like to use them, you must answer Y or M to this option. Note that + for use as console, it must be included in kernel and not as a + module + +config SERIAL_NUVOTON_MA35D1_CONSOLE + bool "Console on a Nuvotn MA35D1 family UART port" + depends on SERIAL_NUVOTON_MA35D1=y + select SERIAL_CORE_CONSOLE + help + Select this options if you'd like to use the UART port0 of the + Nuvoton MA35D1 family as a console. + endmenu config SERIAL_MCTRL_GPIO diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile index cd9afd9e3018..0e823851c42c 100644 --- a/drivers/tty/serial/Makefile +++ b/drivers/tty/serial/Makefile @@ -93,3 +93,4 @@ obj-$(CONFIG_SERIAL_MCTRL_GPIO) += serial_mctrl_gpio.o obj-$(CONFIG_SERIAL_KGDB_NMI) += kgdb_nmi.o obj-$(CONFIG_KGDB_SERIAL_CONSOLE) += kgdboc.o +obj-$(CONFIG_SERIAL_NUVOTON_MA35D1) += ma35d1_serial.o diff --git a/drivers/tty/serial/ma35d1_serial.c b/drivers/tty/serial/ma35d1_serial.c new file mode 100644 index 000000000000..c0a8c1e4ca0e --- /dev/null +++ b/drivers/tty/serial/ma35d1_serial.c @@ -0,0 +1,801 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * MA35D1 serial driver + * Copyright (C) 2023 Nuvoton Technology Corp. + */ + +#include <linux/bitfield.h> +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/of.h> +#include <linux/of_platform.h> +#include <linux/serial_core.h> +#include <linux/slab.h> +#include <linux/tty_flip.h> +#include <linux/units.h> + +#define MA35_UART_NR 17 + +#define MA35_RBR_REG 0x00 +#define MA35_THR_REG 0x00 +#define MA35_IER_REG 0x04 +#define MA35_FCR_REG 0x08 +#define MA35_LCR_REG 0x0C +#define MA35_MCR_REG 0x10 +#define MA35_MSR_REG 0x14 +#define MA35_FSR_REG 0x18 +#define MA35_ISR_REG 0x1C +#define MA35_TOR_REG 0x20 +#define MA35_BAUD_REG 0x24 +#define MA35_ALTCTL_REG 0x2C +#define MA35_FUN_SEL_REG 0x30 +#define MA35_WKCTL_REG 0x40 +#define MA35_WKSTS_REG 0x44 + +/* MA35_IER_REG - Interrupt Enable Register */ +#define MA35_IER_RDA_IEN BIT(0) /* RBR Available Interrupt Enable */ +#define MA35_IER_THRE_IEN BIT(1) /* THR Empty Interrupt Enable */ +#define MA35_IER_RLS_IEN BIT(2) /* RX Line Status Interrupt Enable */ +#define MA35_IER_RTO_IEN BIT(4) /* RX Time-out Interrupt Enable */ +#define MA35_IER_BUFERR_IEN BIT(5) /* Buffer Error Interrupt Enable */ +#define MA35_IER_TIME_OUT_EN BIT(11) /* RX Buffer Time-out Counter Enable */ +#define MA35_IER_AUTO_RTS BIT(12) /* nRTS Auto-flow Control Enable */ +#define MA35_IER_AUTO_CTS BIT(13) /* nCTS Auto-flow Control Enable */ + +/* MA35_FCR_REG - FIFO Control Register */ +#define MA35_FCR_RFR BIT(1) /* RX Field Software Reset */ +#define MA35_FCR_TFR BIT(2) /* TX Field Software Reset */ +#define MA35_FCR_RFITL_MASK GENMASK(7, 4) /* RX FIFO Interrupt Trigger Level */ +#define MA35_FCR_RFITL_1BYTE FIELD_PREP(MA35_FCR_RFITL_MASK, 0) +#define MA35_FCR_RFITL_4BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 1) +#define MA35_FCR_RFITL_8BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 2) +#define MA35_FCR_RFITL_14BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 3) +#define MA35_FCR_RFITL_30BYTES FIELD_PREP(MA35_FCR_RFITL_MASK, 4) +#define MA35_FCR_RTSTL_MASK GENMASK(19, 16) /* nRTS Trigger Level */ +#define MA35_FCR_RTSTL_1BYTE FIELD_PREP(MA35_FCR_RTSTL_MASK, 0) +#define MA35_FCR_RTSTL_4BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 1) +#define MA35_FCR_RTSTL_8BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 2) +#define MA35_FCR_RTSTL_14BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 3) +#define MA35_FCR_RTSTLL_30BYTES FIELD_PREP(MA35_FCR_RTSTL_MASK, 4) + +/* MA35_LCR_REG - Line Control Register */ +#define MA35_LCR_NSB BIT(2) /* Number of “STOP Bit” */ +#define MA35_LCR_PBE BIT(3) /* Parity Bit Enable */ +#define MA35_LCR_EPE BIT(4) /* Even Parity Enable */ +#define MA35_LCR_SPE BIT(5) /* Stick Parity Enable */ +#define MA35_LCR_BREAK BIT(6) /* Break Control */ +#define MA35_LCR_WLS_MASK GENMASK(1, 0) /* Word Length Selection */ +#define MA35_LCR_WLS_5BITS FIELD_PREP(MA35_LCR_WLS_MASK, 0) +#define MA35_LCR_WLS_6BITS FIELD_PREP(MA35_LCR_WLS_MASK, 1) +#define MA35_LCR_WLS_7BITS FIELD_PREP(MA35_LCR_WLS_MASK, 2) +#define MA35_LCR_WLS_8BITS FIELD_PREP(MA35_LCR_WLS_MASK, 3) + +/* MA35_MCR_REG - Modem Control Register */ +#define MA35_MCR_RTS_CTRL BIT(1) /* nRTS Signal Control */ +#define MA35_MCR_RTSACTLV BIT(9) /* nRTS Pin Active Level */ +#define MA35_MCR_RTSSTS BIT(13) /* nRTS Pin Status (Read Only) */ + +/* MA35_MSR_REG - Modem Status Register */ +#define MA35_MSR_CTSDETF BIT(0) /* Detect nCTS State Change Flag */ +#define MA35_MSR_CTSSTS BIT(4) /* nCTS Pin Status (Read Only) */ +#define MA35_MSR_CTSACTLV BIT(8) /* nCTS Pin Active Level */ + +/* MA35_FSR_REG - FIFO Status Register */ +#define MA35_FSR_RX_OVER_IF BIT(0) /* RX Overflow Error Interrupt Flag */ +#define MA35_FSR_PEF BIT(4) /* Parity Error Flag*/ +#define MA35_FSR_FEF BIT(5) /* Framing Error Flag */ +#define MA35_FSR_BIF BIT(6) /* Break Interrupt Flag */ +#define MA35_FSR_RX_EMPTY BIT(14) /* Receiver FIFO Empty (Read Only) */ +#define MA35_FSR_RX_FULL BIT(15) /* Receiver FIFO Full (Read Only) */ +#define MA35_FSR_TX_EMPTY BIT(22) /* Transmitter FIFO Empty (Read Only) */ +#define MA35_FSR_TX_FULL BIT(23) /* Transmitter FIFO Full (Read Only) */ +#define MA35_FSR_TX_OVER_IF BIT(24) /* TX Overflow Error Interrupt Flag */ +#define MA35_FSR_TE_FLAG BIT(28) /* Transmitter Empty Flag (Read Only) */ +#define MA35_FSR_RXPTR_MSK GENMASK(13, 8) /* TX FIFO Pointer mask */ +#define MA35_FSR_TXPTR_MSK GENMASK(21, 16) /* RX FIFO Pointer mask */ + +/* MA35_ISR_REG - Interrupt Status Register */ +#define MA35_ISR_RDA_IF BIT(0) /* RBR Available Interrupt Flag */ +#define MA35_ISR_THRE_IF BIT(1) /* THR Empty Interrupt Flag */ +#define MA35_ISR_RLSIF BIT(2) /* Receive Line Interrupt Flag */ +#define MA35_ISR_MODEMIF BIT(3) /* MODEM Interrupt Flag */ +#define MA35_ISR_RXTO_IF BIT(4) /* RX Time-out Interrupt Flag */ +#define MA35_ISR_BUFEIF BIT(5) /* Buffer Error Interrupt Flag */ +#define MA35_ISR_WK_IF BIT(6) /* UART Wake-up Interrupt Flag */ +#define MA35_ISR_RDAINT BIT(8) /* RBR Available Interrupt Indicator */ +#define MA35_ISR_THRE_INT BIT(9) /* THR Empty Interrupt Indicator */ +#define MA35_ISR_ALL 0xFFFFFFFF + +/* MA35_BAUD_REG - Baud Rate Divider Register */ +#define MA35_BAUD_MODE_MASK GENMASK(29, 28) +#define MA35_BAUD_MODE0 FIELD_PREP(MA35_BAUD_MODE_MASK, 0) +#define MA35_BAUD_MODE1 FIELD_PREP(MA35_BAUD_MODE_MASK, 2) +#define MA35_BAUD_MODE2 FIELD_PREP(MA35_BAUD_MODE_MASK, 3) +#define MA35_BAUD_MASK GENMASK(15, 0) + +/* MA35_ALTCTL_REG - Alternate Control/Status Register */ +#define MA35_ALTCTL_RS485AUD BIT(10) /* RS-485 Auto Direction Function */ + +/* MA35_FUN_SEL_REG - Function Select Register */ +#define MA35_FUN_SEL_MASK GENMASK(2, 0) +#define MA35_FUN_SEL_UART FIELD_PREP(MA35_FUN_SEL_MASK, 0) +#define MA35_FUN_SEL_RS485 FIELD_PREP(MA35_FUN_SEL_MASK, 3) + +/* The constrain for MA35D1 UART baud rate divider */ +#define MA35_BAUD_DIV_MAX 0xFFFF +#define MA35_BAUD_DIV_MIN 11 + +/* UART FIFO depth */ +#define MA35_UART_FIFO_DEPTH 32 +/* UART console clock */ +#define MA35_UART_CONSOLE_CLK (24 * HZ_PER_MHZ) +/* UART register ioremap size */ +#define MA35_UART_REG_SIZE 0x100 +/* Rx Timeout */ +#define MA35_UART_RX_TOUT 0x40 + +#define MA35_ISR_IF_CHECK (MA35_ISR_RDA_IF | MA35_ISR_RXTO_IF | \ + MA35_ISR_THRE_INT | MA35_ISR_BUFEIF) + +static struct uart_driver ma35d1serial_reg; + +struct uart_ma35d1_port { + struct uart_port port; + struct clk *clk; + u16 capabilities; /* port capabilities */ + u8 ier; + u8 lcr; + u8 mcr; + u32 baud_rate; + u32 console_baud_rate; + u32 console_line; + u32 console_int; +}; + +static struct uart_ma35d1_port ma35d1serial_ports[MA35_UART_NR]; + +static struct uart_ma35d1_port *to_ma35d1_uart_port(struct uart_port *uart) +{ + return container_of(uart, struct uart_ma35d1_port, port); +} + +static u32 serial_in(struct uart_ma35d1_port *p, u32 offset) +{ + return readl_relaxed(p->port.membase + offset); +} + +static void serial_out(struct uart_ma35d1_port *p, u32 offset, u32 value) +{ + writel_relaxed(value, p->port.membase + offset); +} + +static void __stop_tx(struct uart_ma35d1_port *p) +{ + u32 ier; + + ier = serial_in(p, MA35_IER_REG); + if (ier & MA35_IER_THRE_IEN) + serial_out(p, MA35_IER_REG, ier & ~MA35_IER_THRE_IEN); +} + +static void ma35d1serial_stop_tx(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + __stop_tx(up); +} + +static void transmit_chars(struct uart_ma35d1_port *up) +{ + u32 count; + u8 ch; + + if (uart_tx_stopped(&up->port)) { + ma35d1serial_stop_tx(&up->port); + return; + } + count = MA35_UART_FIFO_DEPTH - FIELD_GET(MA35_FSR_TXPTR_MSK, + serial_in(up, MA35_FSR_REG)); + uart_port_tx_limited(&up->port, ch, count, + !(serial_in(up, MA35_FSR_REG) & MA35_FSR_TX_FULL), + serial_out(up, MA35_THR_REG, ch), + ({})); +} + +static void ma35d1serial_start_tx(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + u32 ier; + + ier = serial_in(up, MA35_IER_REG); + serial_out(up, MA35_IER_REG, ier & ~MA35_IER_THRE_IEN); + transmit_chars(up); + serial_out(up, MA35_IER_REG, ier | MA35_IER_THRE_IEN); +} + +static void ma35d1serial_stop_rx(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + serial_out(up, MA35_IER_REG, serial_in(up, MA35_IER_REG) & ~MA35_IER_RDA_IEN); +} + +static void receive_chars(struct uart_ma35d1_port *up) +{ + u8 ch, flag; + u32 fsr; + int max_count = 256; + + fsr = serial_in(up, MA35_FSR_REG); + do { + flag = TTY_NORMAL; + up->port.icount.rx++; + + if (unlikely(fsr & (MA35_FSR_BIF | MA35_FSR_FEF | + MA35_FSR_PEF | MA35_FSR_RX_OVER_IF))) { + if (fsr & MA35_FSR_BIF) { + up->port.icount.brk++; + if (uart_handle_break(&up->port)) + continue; + } + if (fsr & MA35_FSR_FEF) + up->port.icount.frame++; + if (fsr & MA35_FSR_PEF) + up->port.icount.parity++; + if (fsr & MA35_FSR_RX_OVER_IF) + up->port.icount.overrun++; + + serial_out(up, MA35_FSR_REG, + fsr & (MA35_FSR_BIF | MA35_FSR_FEF | + MA35_FSR_PEF | MA35_FSR_RX_OVER_IF)); + if (fsr & MA35_FSR_BIF) + flag = TTY_BREAK; + else if (fsr & MA35_FSR_PEF) + flag = TTY_PARITY; + else if (fsr & MA35_FSR_FEF) + flag = TTY_FRAME; + } + + ch = serial_in(up, MA35_RBR_REG); + if (uart_handle_sysrq_char(&up->port, ch)) + continue; + + spin_lock(&up->port.lock); + uart_insert_char(&up->port, fsr, MA35_FSR_RX_OVER_IF, ch, flag); + spin_unlock(&up->port.lock); + + fsr = serial_in(up, MA35_FSR_REG); + } while (!(fsr & MA35_FSR_RX_EMPTY) && (max_count-- > 0)); + + spin_lock(&up->port.lock); + tty_flip_buffer_push(&up->port.state->port); + spin_unlock(&up->port.lock); +} + +static irqreturn_t ma35d1serial_interrupt(int irq, void *dev_id) +{ + struct uart_port *port = dev_id; + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + u32 isr, fsr; + + isr = serial_in(up, MA35_ISR_REG); + fsr = serial_in(up, MA35_FSR_REG); + + if (!(isr & MA35_ISR_IF_CHECK)) + return IRQ_NONE; + + if (isr & (MA35_ISR_RDA_IF | MA35_ISR_RXTO_IF)) + receive_chars(up); + if (isr & MA35_ISR_THRE_INT) + transmit_chars(up); + if (fsr & MA35_FSR_TX_OVER_IF) + serial_out(up, MA35_FSR_REG, MA35_FSR_TX_OVER_IF); + + return IRQ_HANDLED; +} + +static u32 ma35d1serial_tx_empty(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + u32 fsr; + + fsr = serial_in(up, MA35_FSR_REG); + return (fsr & (MA35_FSR_TE_FLAG | MA35_FSR_TX_EMPTY)) == + (MA35_FSR_TE_FLAG | MA35_FSR_TX_EMPTY) ? TIOCSER_TEMT : 0; +} + +static u32 ma35d1serial_get_mctrl(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + u32 status; + u32 ret = 0; + + status = serial_in(up, MA35_MSR_REG); + if (!(status & MA35_MSR_CTSSTS)) + ret |= TIOCM_CTS; + return ret; +} + +static void ma35d1serial_set_mctrl(struct uart_port *port, u32 mctrl) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + u32 mcr; + u32 ier; + + mcr = serial_in(up, MA35_MCR_REG); + mcr &= ~MA35_MCR_RTS_CTRL; + + if (mctrl & TIOCM_RTS) + mcr |= MA35_MCR_RTSACTLV; + else + mcr &= ~MA35_MCR_RTSACTLV; + + if (up->mcr & UART_MCR_AFE) { + serial_out(up, MA35_IER_REG, (serial_in(up, MA35_IER_REG) | + MA35_IER_AUTO_RTS | + MA35_IER_AUTO_CTS)); + up->port.flags |= UPF_HARD_FLOW; + } else { + ier = serial_in(up, MA35_IER_REG); + ier &= ~(MA35_IER_AUTO_RTS | MA35_IER_AUTO_CTS); + serial_out(up, MA35_IER_REG, ier); + up->port.flags &= ~UPF_HARD_FLOW; + } + serial_out(up, MA35_MSR_REG, (serial_in(up, MA35_MSR_REG) | + MA35_MSR_CTSACTLV)); + serial_out(up, MA35_MCR_REG, mcr); +} + +static void ma35d1serial_break_ctl(struct uart_port *port, int break_state) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + unsigned long flags; + u32 lcr; + + spin_lock_irqsave(&up->port.lock, flags); + lcr = serial_in(up, MA35_LCR_REG); + if (break_state != 0) + lcr |= MA35_LCR_BREAK; + else + lcr &= ~MA35_LCR_BREAK; + serial_out(up, MA35_LCR_REG, lcr); + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int ma35d1serial_startup(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + int retval; + + /* Reset FIFO */ + serial_out(up, MA35_FCR_REG, MA35_FCR_TFR | MA35_FCR_RFR); + + /* Clear pending interrupts */ + serial_out(up, MA35_ISR_REG, MA35_ISR_ALL); + + retval = request_irq(port->irq, ma35d1serial_interrupt, 0, + dev_name(port->dev), port); + if (retval) { + dev_err(up->port.dev, "request irq failed.\n"); + return retval; + } + + serial_out(up, MA35_FCR_REG, serial_in(up, MA35_FCR_REG) | + MA35_FCR_RFITL_4BYTES | MA35_FCR_RTSTL_8BYTES); + serial_out(up, MA35_LCR_REG, MA35_LCR_WLS_8BITS); + serial_out(up, MA35_TOR_REG, MA35_UART_RX_TOUT); + serial_out(up, MA35_IER_REG, MA35_IER_RTO_IEN | MA35_IER_RDA_IEN | + MA35_IER_TIME_OUT_EN | MA35_IER_BUFERR_IEN); + return 0; +} + +static void ma35d1serial_shutdown(struct uart_port *port) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + serial_out(up, MA35_IER_REG, 0); + free_irq(port->irq, port); +} + +static void ma35d1serial_set_termios(struct uart_port *port, + struct ktermios *termios, + const struct ktermios *old) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + u32 lcr = 0; + unsigned long flags; + u32 baud, quot; + + lcr = UART_LCR_WLEN(tty_get_char_size(termios->c_cflag)); + + if (termios->c_cflag & CSTOPB) + lcr |= MA35_LCR_NSB; + if (termios->c_cflag & PARENB) + lcr |= MA35_LCR_PBE; + if (!(termios->c_cflag & PARODD)) + lcr |= MA35_LCR_EPE; + if (termios->c_cflag & CMSPAR) + lcr |= MA35_LCR_SPE; + + baud = uart_get_baud_rate(port, termios, old, + port->uartclk / MA35_BAUD_DIV_MAX, + port->uartclk / MA35_BAUD_DIV_MIN); + + /* MA35D1 UART baud rate equation: baudrate = UART_CLK / (quot + 2) */ + quot = (port->uartclk / baud) - 2; + + /* + * Ok, we're now changing the port state. Do it with + * interrupts disabled. + */ + spin_lock_irqsave(&up->port.lock, flags); + + up->port.read_status_mask = MA35_FSR_RX_OVER_IF; + if (termios->c_iflag & INPCK) + up->port.read_status_mask |= MA35_FSR_FEF | MA35_FSR_PEF; + if (termios->c_iflag & (BRKINT | PARMRK)) + up->port.read_status_mask |= MA35_FSR_BIF; + + /* Characteres to ignore */ + up->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= MA35_FSR_FEF | MA35_FSR_PEF; + if (termios->c_iflag & IGNBRK) { + up->port.ignore_status_mask |= MA35_FSR_BIF; + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + up->port.ignore_status_mask |= MA35_FSR_RX_OVER_IF; + } + if (termios->c_cflag & CRTSCTS) + up->mcr |= UART_MCR_AFE; + else + up->mcr &= ~UART_MCR_AFE; + + uart_update_timeout(port, termios->c_cflag, baud); + + ma35d1serial_set_mctrl(&up->port, up->port.mctrl); + + serial_out(up, MA35_BAUD_REG, MA35_BAUD_MODE2 | FIELD_PREP(MA35_BAUD_MASK, quot)); + + serial_out(up, MA35_LCR_REG, lcr); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static const char *ma35d1serial_type(struct uart_port *port) +{ + return port->type == PORT_MA35 ? "ma35d1-uart" : NULL; +} + +static void ma35d1serial_config_port(struct uart_port *port, int flags) +{ + if (flags & UART_CONFIG_TYPE) + port->type = PORT_MA35; +} + +static int ma35d1serial_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + if (port->type != PORT_UNKNOWN && ser->type != PORT_MA35) + return -EINVAL; + + return 0; +} + +static const struct uart_ops ma35d1serial_ops = { + .tx_empty = ma35d1serial_tx_empty, + .set_mctrl = ma35d1serial_set_mctrl, + .get_mctrl = ma35d1serial_get_mctrl, + .stop_tx = ma35d1serial_stop_tx, + .start_tx = ma35d1serial_start_tx, + .stop_rx = ma35d1serial_stop_rx, + .break_ctl = ma35d1serial_break_ctl, + .startup = ma35d1serial_startup, + .shutdown = ma35d1serial_shutdown, + .set_termios = ma35d1serial_set_termios, + .type = ma35d1serial_type, + .config_port = ma35d1serial_config_port, + .verify_port = ma35d1serial_verify_port, +}; + +static const struct of_device_id ma35d1_serial_of_match[] = { + { .compatible = "nuvoton,ma35d1-uart" }, + {}, +}; +MODULE_DEVICE_TABLE(of, ma35d1_serial_of_match); + +#ifdef CONFIG_SERIAL_NUVOTON_MA35D1_CONSOLE + +static struct device_node *ma35d1serial_uart_nodes[MA35_UART_NR]; + +static void wait_for_xmitr(struct uart_ma35d1_port *up) +{ + unsigned int tmout; + + /* Wait up to 10ms for the character(s) to be sent. */ + tmout = 10000; + while (--tmout) { + if (serial_in(up, MA35_FSR_REG) & MA35_FSR_TX_EMPTY) + break; + udelay(1); + } +} + +static void ma35d1serial_console_putchar(struct uart_port *port, unsigned char ch) +{ + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + wait_for_xmitr(up); + serial_out(up, MA35_THR_REG, ch); +} + +/* + * Print a string to the serial port trying not to disturb + * any possible real use of the port... + * + * The console_lock must be held when we get here. + */ +static void ma35d1serial_console_write(struct console *co, const char *s, u32 count) +{ + struct uart_ma35d1_port *up = &ma35d1serial_ports[co->index]; + unsigned long flags; + u32 ier; + + spin_lock_irqsave(&up->port.lock, flags); + + /* + * First save the IER then disable the interrupts + */ + ier = serial_in(up, MA35_IER_REG); + serial_out(up, MA35_IER_REG, 0); + + uart_console_write(&up->port, s, count, ma35d1serial_console_putchar); + + wait_for_xmitr(up); + serial_out(up, MA35_IER_REG, ier); + + spin_unlock_irqrestore(&up->port.lock, flags); +} + +static int __init ma35d1serial_console_setup(struct console *co, char *options) +{ + struct device_node *np; + struct uart_ma35d1_port *p; + u32 val32[4]; + struct uart_port *port; + int baud = 115200; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + if ((co->index < 0) || (co->index >= MA35_UART_NR)) { + pr_debug("Console Port%x out of range\n", co->index); + return -EINVAL; + } + + np = ma35d1serial_uart_nodes[co->index]; + p = &ma35d1serial_ports[co->index]; + if (!np || !p) + return -ENODEV; + + if (of_property_read_u32_array(np, "reg", val32, ARRAY_SIZE(val32)) != 0) + return -EINVAL; + + p->port.iobase = val32[1]; + p->port.membase = ioremap(p->port.iobase, MA35_UART_REG_SIZE); + if (!p->port.membase) + return -ENOMEM; + + p->port.ops = &ma35d1serial_ops; + p->port.line = 0; + p->port.uartclk = MA35_UART_CONSOLE_CLK; + + port = &ma35d1serial_ports[co->index].port; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + + return uart_set_options(port, co, baud, parity, bits, flow); +} + +static struct console ma35d1serial_console = { + .name = "ttyNVT", + .write = ma35d1serial_console_write, + .device = uart_console_device, + .setup = ma35d1serial_console_setup, + .flags = CON_PRINTBUFFER | CON_ENABLED, + .index = -1, + .data = &ma35d1serial_reg, +}; + +static void ma35d1serial_console_init_port(void) +{ + u32 i = 0; + struct device_node *np; + + for_each_matching_node(np, ma35d1_serial_of_match) { + if (ma35d1serial_uart_nodes[i] == NULL) { + of_node_get(np); + ma35d1serial_uart_nodes[i] = np; + i++; + if (i == MA35_UART_NR) + break; + } + } +} + +static int __init ma35d1serial_console_init(void) +{ + ma35d1serial_console_init_port(); + register_console(&ma35d1serial_console); + return 0; +} +console_initcall(ma35d1serial_console_init); + +#define MA35D1SERIAL_CONSOLE (&ma35d1serial_console) +#else +#define MA35D1SERIAL_CONSOLE NULL +#endif + +static struct uart_driver ma35d1serial_reg = { + .owner = THIS_MODULE, + .driver_name = "serial", + .dev_name = "ttyNVT", + .major = TTY_MAJOR, + .minor = 64, + .cons = MA35D1SERIAL_CONSOLE, + .nr = MA35_UART_NR, +}; + +/* + * Register a set of serial devices attached to a platform device. + * The list is terminated with a zero flags entry, which means we expect + * all entries to have at least UPF_BOOT_AUTOCONF set. + */ +static int ma35d1serial_probe(struct platform_device *pdev) +{ + struct resource *res_mem; + struct uart_ma35d1_port *up; + int ret = 0; + + if (pdev->dev.of_node) { + ret = of_alias_get_id(pdev->dev.of_node, "serial"); + if (ret < 0) { + dev_err(&pdev->dev, "failed to get alias/pdev id, errno %d\n", ret); + return ret; + } + } + up = &ma35d1serial_ports[ret]; + up->port.line = ret; + res_mem = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res_mem) + return -ENODEV; + + up->port.iobase = res_mem->start; + up->port.membase = ioremap(up->port.iobase, MA35_UART_REG_SIZE); + up->port.ops = &ma35d1serial_ops; + + spin_lock_init(&up->port.lock); + + up->clk = of_clk_get(pdev->dev.of_node, 0); + if (IS_ERR(up->clk)) { + ret = PTR_ERR(up->clk); + dev_err(&pdev->dev, "failed to get core clk: %d\n", ret); + goto err_iounmap; + } + + ret = clk_prepare_enable(up->clk); + if (ret) + goto err_iounmap; + + if (up->port.line != 0) + up->port.uartclk = clk_get_rate(up->clk); + + ret = platform_get_irq(pdev, 0); + if (ret < 0) + goto err_clk_disable; + + up->port.irq = ret; + up->port.dev = &pdev->dev; + up->port.flags = UPF_BOOT_AUTOCONF; + + platform_set_drvdata(pdev, up); + + ret = uart_add_one_port(&ma35d1serial_reg, &up->port); + if (ret < 0) + goto err_free_irq; + + return 0; + +err_free_irq: + free_irq(up->port.irq, &up->port); + +err_clk_disable: + clk_disable_unprepare(up->clk); + +err_iounmap: + iounmap(up->port.membase); + return ret; +} + +/* + * Remove serial ports registered against a platform device. + */ +static int ma35d1serial_remove(struct platform_device *dev) +{ + struct uart_port *port = platform_get_drvdata(dev); + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + uart_remove_one_port(&ma35d1serial_reg, port); + clk_disable_unprepare(up->clk); + return 0; +} + +static int ma35d1serial_suspend(struct platform_device *dev, pm_message_t state) +{ + struct uart_port *port = platform_get_drvdata(dev); + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + uart_suspend_port(&ma35d1serial_reg, &up->port); + if (up->port.line == 0) { + up->console_baud_rate = serial_in(up, MA35_BAUD_REG); + up->console_line = serial_in(up, MA35_LCR_REG); + up->console_int = serial_in(up, MA35_IER_REG); + } + return 0; +} + +static int ma35d1serial_resume(struct platform_device *dev) +{ + struct uart_port *port = platform_get_drvdata(dev); + struct uart_ma35d1_port *up = to_ma35d1_uart_port(port); + + if (up->port.line == 0) { + serial_out(up, MA35_BAUD_REG, up->console_baud_rate); + serial_out(up, MA35_LCR_REG, up->console_line); + serial_out(up, MA35_IER_REG, up->console_int); + } + uart_resume_port(&ma35d1serial_reg, &up->port); + return 0; +} + +static struct platform_driver ma35d1serial_driver = { + .probe = ma35d1serial_probe, + .remove = ma35d1serial_remove, + .suspend = ma35d1serial_suspend, + .resume = ma35d1serial_resume, + .driver = { + .name = "ma35d1-uart", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(ma35d1_serial_of_match), + }, +}; + +static int __init ma35d1serial_init(void) +{ + int ret; + + ret = uart_register_driver(&ma35d1serial_reg); + if (ret) + return ret; + + ret = platform_driver_register(&ma35d1serial_driver); + if (ret) + uart_unregister_driver(&ma35d1serial_reg); + + return ret; +} + +static void __exit ma35d1serial_exit(void) +{ + platform_driver_unregister(&ma35d1serial_driver); + uart_unregister_driver(&ma35d1serial_reg); +} + +module_init(ma35d1serial_init); +module_exit(ma35d1serial_exit); + +MODULE_LICENSE("GPL"); +MODULE_DESCRIPTION("MA35D1 serial driver"); diff --git a/include/uapi/linux/serial_core.h b/include/uapi/linux/serial_core.h index 281fa286555c..c11600bb1b0d 100644 --- a/include/uapi/linux/serial_core.h +++ b/include/uapi/linux/serial_core.h @@ -279,4 +279,7 @@ /* Sunplus UART */ #define PORT_SUNPLUS 123 +/* Nuvoton MA35 SoC */ +#define PORT_MA35 124 + #endif /* _UAPILINUX_SERIAL_CORE_H */