@@ -190,6 +190,16 @@ config IPQ_APSS_6018
Say Y if you want to support CPU frequency scaling on
ipq based devices.
+config IPQ_CMN_PLL
+ tristate "IPQ CMN PLL Clock Controller"
+ depends on IPQ_GCC_9574
+ help
+ Support for CMN PLL clock controller on IPQ platform. The
+ CMN PLL feeds the reference clocks to the Ethernet devices
+ based on IPQ SoC.
+ Say Y or M if you want to support CMN PLL clock on the IPQ
+ based devices.
+
config IPQ_GCC_4019
tristate "IPQ4019 Global Clock Controller"
help
@@ -29,6 +29,7 @@ obj-$(CONFIG_CLK_X1E80100_TCSRCC) += tcsrcc-x1e80100.o
obj-$(CONFIG_CLK_QCM2290_GPUCC) += gpucc-qcm2290.o
obj-$(CONFIG_IPQ_APSS_PLL) += apss-ipq-pll.o
obj-$(CONFIG_IPQ_APSS_6018) += apss-ipq6018.o
+obj-$(CONFIG_IPQ_CMN_PLL) += clk-ipq-cmn-pll.o
obj-$(CONFIG_IPQ_GCC_4019) += gcc-ipq4019.o
obj-$(CONFIG_IPQ_GCC_5018) += gcc-ipq5018.o
obj-$(CONFIG_IPQ_GCC_5332) += gcc-ipq5332.o
new file mode 100644
@@ -0,0 +1,227 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2024 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/*
+ * CMN PLL block expects the reference clock from on-board Wi-Fi block, and
+ * supplies fixed rate clocks as output to the Ethernet hardware blocks.
+ * The Ethernet related blocks include PPE (packet process engine) and the
+ * external connected PHY (or switch) chip receiving clocks from the CMN PLL.
+ *
+ * On the IPQ9574 SoC, There are three clocks with 50 MHZ, one clock with
+ * 25 MHZ which are output from the CMN PLL to Ethernet PHY (or switch),
+ * and one clock with 353 MHZ to PPE.
+ *
+ * +---------+
+ * | GCC |
+ * +--+---+--+
+ * AHB CLK| |SYS CLK
+ * V V
+ * +-------+---+------+
+ * | +-------------> eth0-50mhz
+ * REF CLK | IPQ9574 |
+ * -------->+ +-------------> eth1-50mhz
+ * | CMN PLL block |
+ * | +-------------> eth2-50mhz
+ * | |
+ * +---------+--------+-------------> eth-25mhz
+ * |
+ * V
+ * ppe-353mhz
+ */
+
+#include <dt-bindings/clock/qcom,ipq-cmn-pll.h>
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define CMN_PLL_REFCLK_SRC_SELECTION 0x28
+#define CMN_PLL_REFCLK_SRC_DIV GENMASK(9, 8)
+
+#define CMN_PLL_REFCLK_CONFIG 0x784
+#define CMN_PLL_REFCLK_EXTERNAL BIT(9)
+#define CMN_PLL_REFCLK_DIV GENMASK(8, 4)
+#define CMN_PLL_REFCLK_INDEX GENMASK(3, 0)
+
+#define CMN_PLL_POWER_ON_AND_RESET 0x780
+#define CMN_ANA_EN_SW_RSTN BIT(6)
+
+/**
+ * struct cmn_pll_fixed_output_clk - CMN PLL output clocks information
+ * @id: Clock specifier to be supplied
+ * @name: Clock name to be registered
+ * @rate: Clock rate
+ */
+struct cmn_pll_fixed_output_clk {
+ unsigned int id;
+ const char *name;
+ const unsigned long rate;
+};
+
+#define CLK_PLL_OUTPUT(_id, _name, _rate) { \
+ .id = _id, \
+ .name = _name, \
+ .rate = _rate, \
+}
+
+static const struct cmn_pll_fixed_output_clk ipq9574_output_clks[] = {
+ CLK_PLL_OUTPUT(PPE_353MHZ_CLK, "ppe-353mhz", 353000000UL),
+ CLK_PLL_OUTPUT(ETH0_50MHZ_CLK, "eth0-50mhz", 50000000UL),
+ CLK_PLL_OUTPUT(ETH1_50MHZ_CLK, "eth1-50mhz", 50000000UL),
+ CLK_PLL_OUTPUT(ETH2_50MHZ_CLK, "eth2-50mhz", 50000000UL),
+ CLK_PLL_OUTPUT(ETH_25MHZ_CLK, "eth-25mhz", 25000000UL),
+};
+
+static int ipq_cmn_pll_config(struct device *dev, unsigned long parent_rate)
+{
+ void __iomem *base;
+ u32 val;
+
+ base = devm_of_iomap(dev, dev->of_node, 0, NULL);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ val = readl(base + CMN_PLL_REFCLK_CONFIG);
+ val &= ~(CMN_PLL_REFCLK_EXTERNAL | CMN_PLL_REFCLK_INDEX);
+
+ /*
+ * Configure the reference input clock selection as per the given rate.
+ * The output clock rates are always of fixed value.
+ */
+ switch (parent_rate) {
+ case 25000000:
+ val |= FIELD_PREP(CMN_PLL_REFCLK_INDEX, 3);
+ break;
+ case 31250000:
+ val |= FIELD_PREP(CMN_PLL_REFCLK_INDEX, 4);
+ break;
+ case 40000000:
+ val |= FIELD_PREP(CMN_PLL_REFCLK_INDEX, 6);
+ break;
+ case 48000000:
+ val |= FIELD_PREP(CMN_PLL_REFCLK_INDEX, 7);
+ break;
+ case 50000000:
+ val |= FIELD_PREP(CMN_PLL_REFCLK_INDEX, 8);
+ break;
+ case 96000000:
+ val |= FIELD_PREP(CMN_PLL_REFCLK_INDEX, 7);
+ val &= ~CMN_PLL_REFCLK_DIV;
+ val |= FIELD_PREP(CMN_PLL_REFCLK_DIV, 2);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ writel(val, base + CMN_PLL_REFCLK_CONFIG);
+
+ /* Update the source clock rate selection. Only 96 MHZ uses 0. */
+ val = readl(base + CMN_PLL_REFCLK_SRC_SELECTION);
+ val &= ~CMN_PLL_REFCLK_SRC_DIV;
+ if (parent_rate != 96000000)
+ val |= FIELD_PREP(CMN_PLL_REFCLK_SRC_DIV, 1);
+
+ writel(val, base + CMN_PLL_REFCLK_SRC_SELECTION);
+
+ /*
+ * Reset the CMN PLL block by asserting/de-asserting for 100 ms
+ * each, to ensure the updated configurations take effect.
+ */
+ val = readl(base + CMN_PLL_POWER_ON_AND_RESET);
+ val &= ~CMN_ANA_EN_SW_RSTN;
+ writel(val, base);
+ msleep(100);
+
+ val |= CMN_ANA_EN_SW_RSTN;
+ writel(val, base + CMN_PLL_POWER_ON_AND_RESET);
+ msleep(100);
+
+ return 0;
+}
+
+static int ipq_cmn_pll_clk_register(struct device *dev, const char *parent)
+{
+ const struct cmn_pll_fixed_output_clk *fixed_clk;
+ struct clk_hw_onecell_data *data;
+ unsigned int num_clks;
+ struct clk_hw *hw;
+ int i;
+
+ num_clks = ARRAY_SIZE(ipq9574_output_clks);
+ fixed_clk = ipq9574_output_clks;
+
+ data = devm_kzalloc(dev, struct_size(data, hws, num_clks), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ for (i = 0; i < num_clks; i++) {
+ hw = devm_clk_hw_register_fixed_rate(dev, fixed_clk[i].name,
+ parent, 0,
+ fixed_clk[i].rate);
+ if (IS_ERR(hw))
+ return PTR_ERR(hw);
+
+ data->hws[fixed_clk[i].id] = hw;
+ }
+ data->num = num_clks;
+
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, data);
+}
+
+static int ipq_cmn_pll_clk_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct clk *clk;
+ int ret;
+
+ /*
+ * To access the CMN PLL registers, the GCC AHB & SYSY clocks
+ * for CMN PLL block need to be enabled.
+ */
+ clk = devm_clk_get_enabled(dev, "ahb");
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk),
+ "Enable AHB clock failed\n");
+
+ clk = devm_clk_get_enabled(dev, "sys");
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk),
+ "Enable SYS clock failed\n");
+
+ clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(clk))
+ return dev_err_probe(dev, PTR_ERR(clk),
+ "Get reference clock failed\n");
+
+ /* Configure CMN PLL to apply the reference clock. */
+ ret = ipq_cmn_pll_config(dev, clk_get_rate(clk));
+ if (ret)
+ return dev_err_probe(dev, ret, "Configure CMN PLL failed\n");
+
+ return ipq_cmn_pll_clk_register(dev, __clk_get_name(clk));
+}
+
+static const struct of_device_id ipq_cmn_pll_clk_ids[] = {
+ { .compatible = "qcom,ipq9574-cmn-pll", },
+ { }
+};
+
+static struct platform_driver ipq_cmn_pll_clk_driver = {
+ .probe = ipq_cmn_pll_clk_probe,
+ .driver = {
+ .name = "ipq_cmn_pll",
+ .of_match_table = ipq_cmn_pll_clk_ids,
+ },
+};
+
+module_platform_driver(ipq_cmn_pll_clk_driver);
+
+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. IPQ CMN PLL Driver");
+MODULE_LICENSE("GPL");
The CMN PLL clock controller supplies clocks to the hardware blocks that together make up the Ethernet function on Qualcomm IPQ SoCs. The driver is initially supported for IPQ9574 SoC. The CMN PLL clock controller expects a reference input clock from the on-board Wi-Fi block acting as clock source. The input reference clock needs to be configured to one of the supported clock rates. The controller supplies a number of fixed-rate output clocks. For the IPQ9574, there is one output clock of 353 MHZ to PPE (Packet Process Engine) hardware block, three 50 MHZ output clocks and an additional 25 MHZ output clock supplied to the connected Ethernet devices. Signed-off-by: Luo Jie <quic_luoj@quicinc.com> --- drivers/clk/qcom/Kconfig | 10 ++ drivers/clk/qcom/Makefile | 1 + drivers/clk/qcom/clk-ipq-cmn-pll.c | 227 +++++++++++++++++++++++++++++++++++++ 3 files changed, 238 insertions(+)