@@ -180,6 +180,17 @@ config REGULATOR_BCM590XX
BCM590xx PMUs. This will enable support for the software
controllable LDO/Switching regulators.
+config REGULATOR_BD71837
+ tristate "ROHM BD71837 Power Regulator"
+ depends on MFD_BD71837
+ help
+ This driver supports voltage regulators on ROHM BD71837 PMIC.
+ This will enable support for the software controllable buck
+ and LDO regulators.
+
+ This driver can also be built as a module. If so, the module
+ will be called bd71837-regulator.
+
config REGULATOR_BD9571MWV
tristate "ROHM BD9571MWV Regulators"
depends on MFD_BD9571MWV
@@ -27,6 +27,7 @@ obj-$(CONFIG_REGULATOR_AS3711) += as3711-regulator.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722-regulator.o
obj-$(CONFIG_REGULATOR_AXP20X) += axp20x-regulator.o
obj-$(CONFIG_REGULATOR_BCM590XX) += bcm590xx-regulator.o
+obj-$(CONFIG_REGULATOR_BD71837) += bd71837-regulator.o
obj-$(CONFIG_REGULATOR_BD9571MWV) += bd9571mwv-regulator.o
obj-$(CONFIG_REGULATOR_DA903X) += da903x.o
obj-$(CONFIG_REGULATOR_DA9052) += da9052-regulator.o
new file mode 100644
@@ -0,0 +1,677 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright (C) 2018 ROHM Semiconductors */
+/*
+ * bd71837-regulator.c ROHM BD71837MWV regulator driver
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/gpio.h>
+#include <linux/mfd/bd71837.h>
+#include <linux/regulator/of_regulator.h>
+
+struct bd71837_pmic {
+ struct regulator_desc descs[BD71837_REGULATOR_CNT];
+ struct bd71837 *mfd;
+ struct platform_device *pdev;
+ struct regulator_dev *rdev[BD71837_REGULATOR_CNT];
+ struct mutex mtx;
+};
+
+/*
+ * BUCK1/2/3/4
+ * BUCK1RAMPRATE[1:0] BUCK1 DVS ramp rate setting
+ * 00: 10.00mV/usec 10mV 1uS
+ * 01: 5.00mV/usec 10mV 2uS
+ * 10: 2.50mV/usec 10mV 4uS
+ * 11: 1.25mV/usec 10mV 8uS
+ */
+static int bd71837_buck1234_set_ramp_delay(struct regulator_dev *rdev,
+ int ramp_delay)
+{
+ struct bd71837_pmic *pmic = rdev_get_drvdata(rdev);
+ struct bd71837 *mfd = pmic->mfd;
+ int id = rdev->desc->id;
+ unsigned int ramp_value = BUCK_RAMPRATE_10P00MV;
+
+ dev_dbg(&(pmic->pdev->dev), "Buck[%d] Set Ramp = %d\n", id + 1,
+ ramp_delay);
+ switch (ramp_delay) {
+ case 1 ... 1250:
+ ramp_value = BUCK_RAMPRATE_1P25MV;
+ break;
+ case 1251 ... 2500:
+ ramp_value = BUCK_RAMPRATE_2P50MV;
+ break;
+ case 2501 ... 5000:
+ ramp_value = BUCK_RAMPRATE_5P00MV;
+ break;
+ case 5001 ... 10000:
+ ramp_value = BUCK_RAMPRATE_10P00MV;
+ break;
+ default:
+ ramp_value = BUCK_RAMPRATE_10P00MV;
+ dev_err(&pmic->pdev->dev,
+ "%s: ramp_delay: %d not supported, setting 10000mV//us\n",
+ rdev->desc->name, ramp_delay);
+ }
+
+ return regmap_update_bits(mfd->regmap, BD71837_REG_BUCK1_CTRL + id,
+ BUCK_RAMPRATE_MASK, ramp_value << 6);
+}
+
+static int bd71837_regulator_set_regmap(struct regulator_dev *rdev, int set)
+{
+ int ret = -EINVAL;
+ struct bd71837_pmic *pmic = rdev->reg_data;
+
+ /* According to the data sheet we must not change regulator voltage
+ * when it is enabled. Thus we need to check if regulator is enabled
+ * before changing the voltage. This mutex is used to avoid race where
+ * we might enable regulator after it's state has been checked but
+ * before the voltage is changed
+ */
+ mutex_lock(&pmic->mtx);
+ if (!set)
+ ret = regulator_disable_regmap(rdev);
+ else
+ ret = regulator_enable_regmap(rdev);
+ mutex_unlock(&pmic->mtx);
+
+ return ret;
+}
+
+static int bd71837_regulator_enable_regmap(struct regulator_dev *rdev)
+{
+ return bd71837_regulator_set_regmap(rdev, 1);
+}
+
+static int bd71837_regulator_disable_regmap(struct regulator_dev *rdev)
+{
+ return bd71837_regulator_set_regmap(rdev, 0);
+}
+
+static int bd71837_regulator_set_voltage_sel_regmap(struct regulator_dev *rdev,
+ unsigned int sel)
+{
+ int ret;
+ struct bd71837_pmic *pmic = rdev->reg_data;
+
+ /* According to the data sheet we must not change regulator voltage
+ * when it is enabled. Error out if regulator is enabled.
+ */
+ mutex_lock(&pmic->mtx);
+ ret = regulator_is_enabled_regmap(rdev);
+ if (!ret)
+ ret = regulator_set_voltage_sel_regmap(rdev, sel);
+ else if (ret == 1)
+ ret = -EBUSY;
+ mutex_unlock(&pmic->mtx);
+ return ret;
+}
+
+static struct regulator_ops bd71837_ldo_regulator_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops bd71837_ldo_regulator_nolinear_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+};
+
+static struct regulator_ops bd71837_buck_regulator_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static struct regulator_ops bd71837_buck_regulator_nolinear_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_table,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+};
+
+static struct regulator_ops bd71837_buck1234_regulator_ops = {
+ .enable = bd71837_regulator_enable_regmap,
+ .disable = bd71837_regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .list_voltage = regulator_list_voltage_linear_range,
+ .set_voltage_sel = bd71837_regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .set_ramp_delay = bd71837_buck1234_set_ramp_delay,
+};
+
+/*
+ * BUCK1/2/3/4
+ * 0.70 to 1.30V (10mV step)
+ */
+static const struct regulator_linear_range bd71837_buck1234_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0x00, 0x3C, 10000),
+ REGULATOR_LINEAR_RANGE(1300000, 0x3D, 0x3F, 0),
+};
+
+/*
+ * BUCK5
+ * 0.9V to 1.35V ()
+ */
+static const struct regulator_linear_range bd71837_buck5_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0x00, 0x03, 100000),
+ REGULATOR_LINEAR_RANGE(1050000, 0x04, 0x05, 50000),
+ REGULATOR_LINEAR_RANGE(1200000, 0x06, 0x07, 150000),
+};
+
+/*
+ * BUCK6
+ * 3.0V to 3.3V (step 100mV)
+ */
+static const struct regulator_linear_range bd71837_buck6_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
+};
+
+/*
+ * BUCK7
+ * 000 = 1.605V
+ * 001 = 1.695V
+ * 010 = 1.755V
+ * 011 = 1.8V (Initial)
+ * 100 = 1.845V
+ * 101 = 1.905V
+ * 110 = 1.95V
+ * 111 = 1.995V
+ */
+static const unsigned int buck_7_volts[] = {
+ 1605000, 1695000, 1755000, 1800000, 1845000, 1905000, 1950000, 1995000
+};
+
+/*
+ * BUCK8
+ * 0.8V to 1.40V (step 10mV)
+ */
+static const struct regulator_linear_range bd71837_buck8_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(800000, 0x00, 0x3C, 10000),
+ REGULATOR_LINEAR_RANGE(1400000, 0x3D, 0x3F, 0),
+};
+
+/*
+ * LDO1
+ * 3.0 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo1_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(3000000, 0x00, 0x03, 100000),
+};
+
+/*
+ * LDO2
+ * 0.8 or 0.9V
+ */
+const unsigned int ldo_2_volts[] = {
+ 900000, 800000
+};
+
+/*
+ * LDO3
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo3_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+/*
+ * LDO4
+ * 0.9 to 1.8V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo4_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
+};
+
+/*
+ * LDO5
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo5_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+/*
+ * LDO6
+ * 0.9 to 1.8V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo6_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(900000, 0x00, 0x09, 100000),
+ REGULATOR_LINEAR_RANGE(1800000, 0x0A, 0x0F, 0),
+};
+
+/*
+ * LDO7
+ * 1.8 to 3.3V (100mV step)
+ */
+static const struct regulator_linear_range bd71837_ldo7_voltage_ranges[] = {
+ REGULATOR_LINEAR_RANGE(1800000, 0x00, 0x0F, 100000),
+};
+
+static const struct regulator_desc bd71837_regulators[] = {
+ {
+ .name = "buck1",
+ .of_match = of_match_ptr("BUCK1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK1,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK1_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK1_VOLT_RUN,
+ .vsel_mask = BUCK1_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK1_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck2",
+ .of_match = of_match_ptr("BUCK2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK2,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK2_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK2_VOLT_RUN,
+ .vsel_mask = BUCK2_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK2_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck3",
+ .of_match = of_match_ptr("BUCK3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK3,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK3_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK3_VOLT_RUN,
+ .vsel_mask = BUCK3_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK3_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck4",
+ .of_match = of_match_ptr("BUCK4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK4,
+ .ops = &bd71837_buck1234_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK4_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck1234_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck1234_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK4_VOLT_RUN,
+ .vsel_mask = BUCK4_RUN_MASK,
+ .enable_reg = BD71837_REG_BUCK4_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck5",
+ .of_match = of_match_ptr("BUCK5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK5,
+ .ops = &bd71837_buck_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK5_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck5_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck5_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK5_VOLT,
+ .vsel_mask = BUCK5_MASK,
+ .enable_reg = BD71837_REG_BUCK5_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck6",
+ .of_match = of_match_ptr("BUCK6"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK6,
+ .ops = &bd71837_buck_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK6_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck6_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck6_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK6_VOLT,
+ .vsel_mask = BUCK6_MASK,
+ .enable_reg = BD71837_REG_BUCK6_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck7",
+ .of_match = of_match_ptr("BUCK7"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK7,
+ .ops = &bd71837_buck_regulator_nolinear_ops,
+ .type = REGULATOR_VOLTAGE,
+ .volt_table = &buck_7_volts[0],
+ .n_voltages = ARRAY_SIZE(buck_7_volts),
+ .vsel_reg = BD71837_REG_BUCK7_VOLT,
+ .vsel_mask = BUCK7_MASK,
+ .enable_reg = BD71837_REG_BUCK7_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "buck8",
+ .of_match = of_match_ptr("BUCK8"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_BUCK8,
+ .ops = &bd71837_buck_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_BUCK8_VOLTAGE_NUM,
+ .linear_ranges = bd71837_buck8_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_buck8_voltage_ranges),
+ .vsel_reg = BD71837_REG_BUCK8_VOLT,
+ .vsel_mask = BUCK8_MASK,
+ .enable_reg = BD71837_REG_BUCK8_CTRL,
+ .enable_mask = BD71837_BUCK_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo1",
+ .of_match = of_match_ptr("LDO1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO1,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO1_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo1_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo1_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO1_VOLT,
+ .vsel_mask = LDO1_MASK,
+ .enable_reg = BD71837_REG_LDO1_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo2",
+ .of_match = of_match_ptr("LDO2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO2,
+ .ops = &bd71837_ldo_regulator_nolinear_ops,
+ .type = REGULATOR_VOLTAGE,
+ .volt_table = &ldo_2_volts[0],
+ .vsel_reg = BD71837_REG_LDO2_VOLT,
+ .vsel_mask = LDO2_MASK,
+ .n_voltages = ARRAY_SIZE(ldo_2_volts),
+ .n_voltages = BD71837_LDO2_VOLTAGE_NUM,
+ .enable_reg = BD71837_REG_LDO2_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo3",
+ .of_match = of_match_ptr("LDO3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO3,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO3_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo3_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo3_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO3_VOLT,
+ .vsel_mask = LDO3_MASK,
+ .enable_reg = BD71837_REG_LDO3_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo4",
+ .of_match = of_match_ptr("LDO4"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO4,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO4_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo4_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo4_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO4_VOLT,
+ .vsel_mask = LDO4_MASK,
+ .enable_reg = BD71837_REG_LDO4_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo5",
+ .of_match = of_match_ptr("LDO5"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO5,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO5_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo5_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo5_voltage_ranges),
+ /* LDO5 is supplied by buck6 */
+ .supply_name = "buck6",
+ .vsel_reg = BD71837_REG_LDO5_VOLT,
+ .vsel_mask = LDO5_MASK,
+ .enable_reg = BD71837_REG_LDO5_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo6",
+ .of_match = of_match_ptr("LDO6"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO6,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO6_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo6_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo6_voltage_ranges),
+ /* LDO6 is supplied by buck7 */
+ .supply_name = "buck7",
+ .vsel_reg = BD71837_REG_LDO6_VOLT,
+ .vsel_mask = LDO6_MASK,
+ .enable_reg = BD71837_REG_LDO6_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+ {
+ .name = "ldo7",
+ .of_match = of_match_ptr("LDO7"),
+ .regulators_node = of_match_ptr("regulators"),
+ .id = BD71837_LDO7,
+ .ops = &bd71837_ldo_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .n_voltages = BD71837_LDO7_VOLTAGE_NUM,
+ .linear_ranges = bd71837_ldo7_voltage_ranges,
+ .n_linear_ranges = ARRAY_SIZE(bd71837_ldo7_voltage_ranges),
+ .vsel_reg = BD71837_REG_LDO7_VOLT,
+ .vsel_mask = LDO7_MASK,
+ .enable_reg = BD71837_REG_LDO7_VOLT,
+ .enable_mask = BD71837_LDO_EN,
+ .owner = THIS_MODULE,
+ },
+};
+
+struct reg_init {
+ unsigned int reg;
+ unsigned int mask;
+};
+
+static int bd71837_probe(struct platform_device *pdev)
+{
+ struct bd71837_pmic *pmic;
+ struct bd71837_board *pdata;
+ struct regulator_config config = { 0 };
+ struct reg_init pmic_regulator_inits[] = {
+ {
+ .reg = BD71837_REG_BUCK1_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK2_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK3_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK4_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK5_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK6_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK7_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_BUCK8_CTRL,
+ .mask = BD71837_BUCK_SEL,
+ }, {
+ .reg = BD71837_REG_LDO1_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO2_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO3_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO4_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO5_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO6_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }, {
+ .reg = BD71837_REG_LDO7_VOLT,
+ .mask = BD71837_LDO_SEL,
+ }
+ };
+
+ int i, err;
+
+ pmic = devm_kzalloc(&pdev->dev, sizeof(struct bd71837_pmic),
+ GFP_KERNEL);
+ if (!pmic)
+ return -ENOMEM;
+
+ mutex_init(&pmic->mtx);
+
+ memcpy(pmic->descs, bd71837_regulators, sizeof(pmic->descs));
+
+ pmic->pdev = pdev;
+ pmic->mfd = dev_get_drvdata(pdev->dev.parent);
+
+ if (!pmic->mfd) {
+ dev_err(&pdev->dev, "No MFD driver data\n");
+ err = -EINVAL;
+ goto err;
+ }
+ platform_set_drvdata(pdev, pmic);
+ pdata = dev_get_platdata(pmic->mfd->dev);
+
+ /* Register LOCK release */
+ err = regmap_update_bits(pmic->mfd->regmap, BD71837_REG_REGLOCK,
+ (REGLOCK_PWRSEQ | REGLOCK_VREG), 0);
+ if (err) {
+ dev_err(&pmic->pdev->dev, "Failed to unlock PMIC (%d)\n", err);
+ goto err;
+ } else {
+ dev_dbg(&pmic->pdev->dev, "%s: Unlocked lock register 0x%x\n",
+ __func__, BD71837_REG_REGLOCK);
+ }
+
+ for (i = 0; i < ARRAY_SIZE(pmic_regulator_inits); i++) {
+
+ struct regulator_desc *desc;
+ struct regulator_dev *rdev;
+
+ desc = &pmic->descs[i];
+
+ if (pdata)
+ config.init_data = pdata->init_data[i];
+
+ config.dev = pdev->dev.parent;
+ config.driver_data = pmic;
+ config.regmap = pmic->mfd->regmap;
+
+ rdev = devm_regulator_register(&pdev->dev, desc, &config);
+ if (IS_ERR(rdev)) {
+ dev_err(pmic->mfd->dev,
+ "failed to register %s regulator\n",
+ desc->name);
+ err = PTR_ERR(rdev);
+ goto err;
+ }
+ /* Regulator register gets the regulator constraints and
+ * applies them (set_machine_constraints). This should have
+ * turned the control register(s) to correct values and we
+ * can now switch the control from PMIC state machine to the
+ * register interface
+ */
+ err = regmap_update_bits(pmic->mfd->regmap,
+ pmic_regulator_inits[i].reg,
+ pmic_regulator_inits[i].mask,
+ 0xFFFFFFFF);
+ if (err) {
+ dev_err(&pmic->pdev->dev,
+ "Failed to write BUCK/LDO SEL bit for (%s)\n",
+ desc->name);
+ goto err;
+ }
+
+ pmic->rdev[i] = rdev;
+ }
+
+ return 0;
+
+err:
+ return err;
+}
+
+static struct platform_driver bd71837_regulator = {
+ .driver = {
+ .name = "bd71837-pmic",
+ .owner = THIS_MODULE,
+ },
+ .probe = bd71837_probe,
+};
+
+module_platform_driver(bd71837_regulator);
+
+MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>");
+MODULE_DESCRIPTION("BD71837 voltage regulator driver");
+MODULE_LICENSE("GPL");
Support for controlling the 8 bucks and 7 LDOs the PMIC contains. Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> --- drivers/regulator/Kconfig | 11 + drivers/regulator/Makefile | 1 + drivers/regulator/bd71837-regulator.c | 677 ++++++++++++++++++++++++++++++++++ 3 files changed, 689 insertions(+) create mode 100644 drivers/regulator/bd71837-regulator.c