diff mbox series

[v2,43/45] ARM: dts: at91: sam9x7: add device tree for SoC

Message ID 20230623203056.689705-44-varshini.rajendran@microchip.com (mailing list archive)
State Not Applicable
Delegated to: Herbert Xu
Headers show
Series Add support for sam9x7 SoC family | expand

Commit Message

Varshini Rajendran June 23, 2023, 8:30 p.m. UTC 
Add device tree file for SAM9X7 SoC family.

Co-developed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
---
 arch/arm/boot/dts/sam9x7.dtsi | 1237 +++++++++++++++++++++++++++++++++
 1 file changed, 1237 insertions(+)
 create mode 100644 arch/arm/boot/dts/sam9x7.dtsi

Comments

Krzysztof Kozlowski June 24, 2023, 8:09 a.m. UTC | #1 
On 23/06/2023 22:30, Varshini Rajendran wrote:
> Add device tree file for SAM9X7 SoC family.
> 
> Co-developed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
> Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
> Signed-off-by: Varshini Rajendran <varshini.rajendran@microchip.com>
> ---
>  arch/arm/boot/dts/sam9x7.dtsi | 1237 +++++++++++++++++++++++++++++++++
>  1 file changed, 1237 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sam9x7.dtsi
> 
> diff --git a/arch/arm/boot/dts/sam9x7.dtsi b/arch/arm/boot/dts/sam9x7.dtsi
> new file mode 100644
> index 000000000000..535a55f13dd0
> --- /dev/null
> +++ b/arch/arm/boot/dts/sam9x7.dtsi
> @@ -0,0 +1,1237 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
> + *
> + * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
> + *
> + * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
> + */
> +
> +#include <dt-bindings/clock/at91.h>
> +#include <dt-bindings/dma/at91.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
> +#include <dt-bindings/mfd/atmel-flexcom.h>
> +#include <dt-bindings/pinctrl/at91.h>
> +
> +/ {
> +	#address-cells = <1>;
> +	#size-cells = <1>;
> +	model = "Microchip SAM9X7 SoC";
> +	compatible = "microchip,sam9x7";
> +	interrupt-parent = <&aic>;
> +
> +	aliases {
> +		serial0 = &dbgu;

serial alias is rarely property of SoC. Do you claim that absolutely all
boards must use this serial and they cannot use anything else?

> +		gpio0 = &pioA;
> +		gpio1 = &pioB;
> +		gpio2 = &pioC;
> +		gpio3 = &pioD;

GPIOs are discussible but sometimes we keep them in SoC DTSI.

> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu@0 {
> +			compatible = "arm,arm926ej-s";
> +			device_type = "cpu";
> +			reg = <0>;
> +		};
> +	};
> +
> +	clocks {
> +		slow_xtal: clock-slowxtal {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +		};
> +
> +		main_xtal: clock-mainxtal {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +		};
> +	};
> +
> +	sram: sram@300000 {
> +		compatible = "mmio-sram";
> +		reg = <0x300000 0x10000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges = <0 0x300000 0x10000>;
> +	};
> +
> +	ahb {
> +		compatible = "simple-bus";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ranges;
> +
> +		usb0: gadget@500000 {
> +			compatible = "microchip,sam9x7-udc", "microchip,sam9x60-udc";
> +			reg = <0x500000 0x100000>,
> +			      <0xf803c000 0x400>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			clock-names = "pclk", "hclk";
> +			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			assigned-clock-rates = <480000000>;
> +			status = "disabled";
> +		};
> +
> +		ohci0: usb@600000 {
> +			compatible = "microchip,sam9x7-ohci", "atmel,at91rm9200-ohci", "usb-ohci";
> +			reg = <0x600000 0x100000>;
> +			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
> +			clock-names = "ohci_clk", "hclk", "uhpck";
> +			status = "disabled";
> +		};
> +
> +		ehci0: usb@700000 {
> +			compatible = "microchip,sam9x7-ehci", "atmel,at91sam9g45-ehci", "usb-ehci";
> +			reg = <0x700000 0x100000>;
> +			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
> +			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
> +			clock-names = "usb_clk", "ehci_clk";
> +			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
> +			assigned-clock-rates = <480000000>;
> +			status = "disabled";
> +		};
> +
> +		sdmmc0: sdio-host@80000000 {

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";

So none of your DTS and bindings patches were tested... Limited review
follows as there is little sense to use reviewers time if you can use
machine.

> +			reg = <0x80000000 0x300>;
> +			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
> +			clock-names = "hclock", "multclk";
> +			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
> +			assigned-clock-rates = <100000000>;
> +			status = "disabled";
> +		};
> +
> +		sdmmc1: sdio-host@90000000 {

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
> +			reg = <0x90000000 0x300>;
> +			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
> +			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
> +			clock-names = "hclock", "multclk";
> +			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
> +			assigned-clock-rates = <100000000>;
> +			status = "disabled";
> +		};
> +
> +		apb {
> +			compatible = "simple-bus";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			flx4: flexcom@f0000000 {
> +				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
> +				reg = <0xf0000000 0x200>;
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				ranges = <0x0 0xf0000000 0x800>;
> +				status = "disabled";
> +
> +				uart4: serial@200 {
> +					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";

Please run scripts/checkpatch.pl and fix reported warnings. Some
warnings can be ignored, but the code here looks like it needs a fix.
Feel free to get in touch if the warning is not clear.

> +					reg = <0x200 0x200>;
> +					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
> +					dmas = <&dma0
> +						(AT91_XDMAC_DT_ME

...


> +
> +			dbgu: serial@fffff200 {
> +				compatible = "microchip,sam9x7-dbgu", "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";

I wonder if we can make the line longer...

> +				reg = <0xfffff200 0x200>;
> +				interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
> +				dmas = <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(28))>,
> +				       <&dma0
> +					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
> +					 AT91_XDMAC_DT_PERID(29))>;
> +				dma-names = "tx", "rx";
> +				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
> +				clock-names = "usart";
> +				status = "disabled";
> +			};
> +
> +			pinctrl: pinctrl@fffff400 {
> +				#address-cells = <1>;
> +				#size-cells = <1>;
> +				compatible = "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-mfd";
> +				ranges = <0xfffff400 0xfffff400 0x800>;
> +
> +				/* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
> +				atmel,mux-mask = <
> +						 /*  A		B	   C	      D	  */
> +						 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000	/* pioA */
> +						 0x07ffffff 0x0805fe7f 0x01ff9f80 0x06078000	/* pioB */
> +						 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000	/* pioC */
> +						 0x00003fff 0x00003fe0 0x0000003f 0x00000000	/* pioD */
> +						 >;
> +
> +				pioA: gpio@fffff400 {
> +					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +					reg = <0xfffff400 0x200>;
> +					interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
> +					#gpio-cells = <2>;
> +					gpio-controller;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
> +				};
> +
> +				pioB: gpio@fffff600 {
> +					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +					reg = <0xfffff600 0x200>;
> +					interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
> +					#gpio-cells = <2>;
> +					gpio-controller;
> +					#gpio-lines = <26>;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
> +				};
> +
> +				pioC: gpio@fffff800 {
> +					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +					reg = <0xfffff800 0x200>;
> +					interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
> +					#gpio-cells = <2>;
> +					gpio-controller;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
> +				};
> +
> +				pioD: gpio@fffffa00 {
> +					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
> +					reg = <0xfffffa00 0x200>;
> +					interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
> +					#gpio-cells = <2>;
> +					gpio-controller;
> +					#gpio-lines = <22>;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +					clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
> +				};
> +			};
> +
> +			pmc: pmc@fffffc00 {
> +				compatible = "microchip,sam9x7-pmc", "syscon";
> +				reg = <0xfffffc00 0x200>;
> +				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
> +				#clock-cells = <2>;
> +				clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
> +				clock-names = "td_slck", "md_slck", "main_xtal";
> +			};
> +
> +			reset_controller: rstc@fffffe00 {

reset-controller

> +				compatible = "microchip,sam9x7-rstc", "microchip,sam9x60-rstc";
> +				reg = <0xfffffe00 0x10>;
> +				clocks = <&clk32k 0>;
> +			};
> +
> +			shutdown_controller: shdwc@fffffe10 {

Usually power-management or reset-controller or something like this.



> +				compatible = "microchip,sam9x7-shdwc", "microchip,sam9x60-shdwc";
> +				reg = <0xfffffe10 0x10>;
> +				clocks = <&clk32k 0>;
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +				atmel,wakeup-rtc-timer;
> +				atmel,wakeup-rtt-timer;
> +				status = "disabled";


Best regards,
Krzysztof
diff mbox series

Patch

diff --git a/arch/arm/boot/dts/sam9x7.dtsi b/arch/arm/boot/dts/sam9x7.dtsi
new file mode 100644
index 000000000000..535a55f13dd0
--- /dev/null
+++ b/arch/arm/boot/dts/sam9x7.dtsi
@@ -0,0 +1,1237 @@ 
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * sam9x7.dtsi - Device Tree Include file for Microchip SAM9X7 SoC family
+ *
+ * Copyright (C) 2023 Microchip Technology Inc. and its subsidiaries
+ *
+ * Author: Varshini Rajendran <varshini.rajendran@microchip.com>
+ */
+
+#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/pinctrl/at91.h>
+
+/ {
+	#address-cells = <1>;
+	#size-cells = <1>;
+	model = "Microchip SAM9X7 SoC";
+	compatible = "microchip,sam9x7";
+	interrupt-parent = <&aic>;
+
+	aliases {
+		serial0 = &dbgu;
+		gpio0 = &pioA;
+		gpio1 = &pioB;
+		gpio2 = &pioC;
+		gpio3 = &pioD;
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			compatible = "arm,arm926ej-s";
+			device_type = "cpu";
+			reg = <0>;
+		};
+	};
+
+	clocks {
+		slow_xtal: clock-slowxtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+
+		main_xtal: clock-mainxtal {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+		};
+	};
+
+	sram: sram@300000 {
+		compatible = "mmio-sram";
+		reg = <0x300000 0x10000>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0 0x300000 0x10000>;
+	};
+
+	ahb {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		usb0: gadget@500000 {
+			compatible = "microchip,sam9x7-udc", "microchip,sam9x60-udc";
+			reg = <0x500000 0x100000>,
+			      <0xf803c000 0x400>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			interrupts = <23 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 23>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			clock-names = "pclk", "hclk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			assigned-clock-rates = <480000000>;
+			status = "disabled";
+		};
+
+		ohci0: usb@600000 {
+			compatible = "microchip,sam9x7-ohci", "atmel,at91rm9200-ohci", "usb-ohci";
+			reg = <0x600000 0x100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_PERIPHERAL 22>, <&pmc PMC_TYPE_SYSTEM 6>;
+			clock-names = "ohci_clk", "hclk", "uhpck";
+			status = "disabled";
+		};
+
+		ehci0: usb@700000 {
+			compatible = "microchip,sam9x7-ehci", "atmel,at91sam9g45-ehci", "usb-ehci";
+			reg = <0x700000 0x100000>;
+			interrupts = <22 IRQ_TYPE_LEVEL_HIGH 2>;
+			clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_PERIPHERAL 22>;
+			clock-names = "usb_clk", "ehci_clk";
+			assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>;
+			assigned-clock-rates = <480000000>;
+			status = "disabled";
+		};
+
+		sdmmc0: sdio-host@80000000 {
+			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0x80000000 0x300>;
+			interrupts = <12 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 12>, <&pmc PMC_TYPE_GCK 12>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 12>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		sdmmc1: sdio-host@90000000 {
+			compatible = "microchip,sam9x7-sdhci", "microchip,sam9x60-sdhci";
+			reg = <0x90000000 0x300>;
+			interrupts = <26 IRQ_TYPE_LEVEL_HIGH 0>;
+			clocks = <&pmc PMC_TYPE_PERIPHERAL 26>, <&pmc PMC_TYPE_GCK 26>;
+			clock-names = "hclock", "multclk";
+			assigned-clocks = <&pmc PMC_TYPE_GCK 26>;
+			assigned-clock-rates = <100000000>;
+			status = "disabled";
+		};
+
+		apb {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			flx4: flexcom@f0000000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf0000000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0000000 0x800>;
+				status = "disabled";
+
+				uart4: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi4: spi@400 {
+					compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c4: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <13 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 13>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(8))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(9))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx5: flexcom@f0004000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf0004000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0004000 0x800>;
+				status = "disabled";
+
+				uart5: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi5: spi@400 {
+					compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c5: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 14>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(10))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(11))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			dma0: dma-controller@f0008000 {
+				compatible = "microchip,sam9x7-dma", "microchip,sam9x60-dma", "atmel,sama5d4-dma";
+				reg = <0xf0008000 0x1000>;
+				interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>;
+				#dma-cells = <1>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
+				clock-names = "dma_clk";
+				status = "disabled";
+			};
+
+			ssc: ssc@f0010000 {
+				compatible = "microchip,sam9x7-ssc", "atmel,at91sam9g45-ssc";
+				reg = <0xf0010000 0x4000>;
+				interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(38))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(39))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 28>;
+				clock-names = "pclk";
+				status = "disabled";
+			};
+
+			i2s: i2s@f001c000 {
+				compatible = "microchip,sam9x7-i2smcc", "microchip,sam9x60-i2smcc";
+				reg = <0xf001c000 0x100>;
+				interrupts = <34 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(36))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(37))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 34>, <&pmc PMC_TYPE_GCK 34>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
+			flx11: flexcom@f0020000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf0020000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0020000 0x800>;
+				status = "disabled";
+
+				uart11: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c11: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 32>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(22))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(23))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx12: flexcom@f0024000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf0024000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf0024000 0x800>;
+				status = "disabled";
+
+				uart12: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c12: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <33 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 33>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(24))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(25))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			pit64b0: timer@f0028000 {
+				compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+				reg = <0xf0028000 0x100>;
+				interrupts = <37 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 37>, <&pmc PMC_TYPE_GCK 37>;
+				clock-names = "pclk", "gclk";
+			};
+
+			sha: crypto@f002c000 {
+				compatible = "microchip,sam9x7-sha", "atmel,at91sam9g46-sha";
+				reg = <0xf002c000 0x100>;
+				interrupts = <41 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(34))>;
+				dma-names = "tx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
+				clock-names = "sha_clk";
+			};
+
+			trng: rng@f0030000 {
+				compatible = "microchip,sam9x7-trng", "microchip,sam9x60-trng";
+				reg = <0xf0030000 0x100>;
+				interrupts = <38 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
+				status = "disabled";
+			};
+
+			aes: crypto@f0034000 {
+				compatible = "microchip,sam9x7-aes", "atmel,at91sam9g46-aes";
+				reg = <0xf0034000 0x100>;
+				interrupts = <39 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(32))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(33))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 39>;
+				clock-names = "aes_clk";
+			};
+
+			tdes: crypto@f0038000 {
+				compatible = "microchip,sam9x7-tdes", "atmel,at91sam9g46-tdes";
+				reg = <0xf0038000 0x100>;
+				interrupts = <40 IRQ_TYPE_LEVEL_HIGH 0>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(31))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(30))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 40>;
+				clock-names = "tdes_clk";
+			};
+
+			classd: classd@f003c000 {
+				compatible = "microchip,sam9x7-classd", "atmel,sama5d2-classd";
+				reg = <0xf003c000 0x100>;
+				interrupts = <42 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(35))>;
+				dma-names = "tx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 42>, <&pmc PMC_TYPE_GCK 42>;
+				clock-names = "pclk", "gclk";
+				status = "disabled";
+			};
+
+			pit64b1: timer@f0040000 {
+				compatible = "microchip,sam9x7-pit64b", "microchip,sam9x60-pit64b";
+				reg = <0xf0040000 0x100>;
+				interrupts = <58 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 58>, <&pmc PMC_TYPE_GCK 58>;
+				clock-names = "pclk", "gclk";
+			};
+
+			can0: can@f8000000 {
+				compatible = "bosch,m_can";
+				reg = <0xf8000000 0x100>, <0x300000 0x7800>;
+				reg-names = "m_can", "message_ram";
+				interrupts = <29 IRQ_TYPE_LEVEL_HIGH 0
+					      68 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupt-names = "int0", "int1";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 29>, <&pmc PMC_TYPE_GCK 29>;
+				clock-names = "hclk", "cclk";
+				assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 29>;
+				assigned-clock-rates = <480000000>, <40000000>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+				bosch,mram-cfg = <0x3400 0 0 64 0 0 32 32>;
+				status = "disabled";
+			};
+
+			can1: can@f8004000 {
+				compatible = "bosch,m_can";
+				reg = <0xf8004000 0x100>, <0x300000 0xbc00>;
+				reg-names = "m_can", "message_ram";
+				interrupts = <30 IRQ_TYPE_LEVEL_HIGH 0
+					      69 IRQ_TYPE_LEVEL_HIGH 0>;
+				interrupt-names = "int0", "int1";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 30>, <&pmc PMC_TYPE_GCK 30>;
+				clock-names = "hclk", "cclk";
+				assigned-clocks = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_GCK 30>;
+				assigned-clock-rates = <480000000>, <40000000>;
+				assigned-clock-parents = <&pmc PMC_TYPE_CORE PMC_UTMI>, <&pmc PMC_TYPE_CORE PMC_UTMI>;
+				bosch,mram-cfg = <0x7800 0 0 64 0 0 32 32>;
+				status = "disabled";
+			};
+
+			tcb: timer@f8008000 {
+				compatible = "microchip,sam9x7-tcb","microchip,sam9x60-tcb", "simple-mfd", "syscon";
+				reg = <0xf8008000 0x100>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <17 IRQ_TYPE_LEVEL_HIGH 0>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 17>, <&clk32k 0>;
+				clock-names = "t0_clk", "slow_clk";
+				status = "disabled";
+			};
+
+			flx6: flexcom@f8010000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8010000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8010000 0x800>;
+				status = "disabled";
+
+				uart6: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c6: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <9 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 9>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(12))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(13))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx7: flexcom@f8014000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8014000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8014000 0x800>;
+				status = "disabled";
+
+				uart7: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c7: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <10 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 10>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(14))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(15))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx8: flexcom@f8018000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8018000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8018000 0x800>;
+				status = "disabled";
+
+				uart8: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c8: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <11 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 11>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(16))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(17))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx0: flexcom@f801c000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf801c000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf801c000 0x800>;
+				status = "disabled";
+
+				uart0: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi0: spi@400 {
+					compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c0: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <5 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 5>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(0))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(1))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx1: flexcom@f8020000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8020000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8020000 0x800>;
+				status = "disabled";
+
+				uart1: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi1: spi@400 {
+					compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c1: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 6>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(2))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(3))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx2: flexcom@f8024000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8024000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8024000 0x800>;
+				status = "disabled";
+
+				uart2: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi2: spi@400 {
+					compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c2: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <7 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(4))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(5))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx3: flexcom@f8028000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8028000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8028000 0x800>;
+				status = "disabled";
+
+				uart3: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				spi3: spi@400 {
+					compatible = "microchip,sam9x7-spi", "microchip,sam9x60-spi", "atmel,at91rm9200-spi";
+					reg = <0x400 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					clock-names = "spi_clk";
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c3: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <8 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 8>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(6))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(7))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			gmac: ethernet@f802c000 {
+				compatible = "microchip,sam9x7-gem", "microchip,sama7g5-gem" ;
+				reg = <0xf802c000 0x1000>;
+				interrupts = <24 IRQ_TYPE_LEVEL_HIGH 3		/* Queue 0 */
+					      60 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 1 */
+					      61 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 2 */
+					      62 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 3 */
+					      63 IRQ_TYPE_LEVEL_HIGH 3          /* Queue 4 */
+					      64 IRQ_TYPE_LEVEL_HIGH 3>;        /* Queue 5 */
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_PERIPHERAL 24>, <&pmc PMC_TYPE_GCK 67>;
+				clock-names = "hclk", "pclk", "tsu_clk";
+				assigned-clocks = <&pmc PMC_TYPE_GCK 67>;
+				status = "disabled";
+			};
+
+			flx9: flexcom@f8040000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8040000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8040000 0x800>;
+				status = "disabled";
+
+				uart9: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c9: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <15 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 15>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(18))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(19))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			flx10: flexcom@f8044000 {
+				compatible = "microchip,sam9x7-flexcom", "atmel,sama5d2-flexcom";
+				reg = <0xf8044000 0x200>;
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0xf8044000 0x800>;
+				status = "disabled";
+
+				uart10: serial@200 {
+					compatible = "microchip,sam9x7-usart", "microchip,sam9x60-usart", "atmel,at91sam9260-usart";
+					reg = <0x200 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					clock-names = "usart";
+					atmel,use-dma-rx;
+					atmel,use-dma-tx;
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+
+				i2c10: i2c@600 {
+					compatible = "microchip,sam9x7-i2c", "microchip,sam9x60-i2c";
+					reg = <0x600 0x200>;
+					interrupts = <16 IRQ_TYPE_LEVEL_HIGH 7>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 16>;
+					dmas = <&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(20))>,
+						<&dma0
+						(AT91_XDMAC_DT_MEM_IF(0) |
+						 AT91_XDMAC_DT_PER_IF(1) |
+						 AT91_XDMAC_DT_PERID(21))>;
+					dma-names = "tx", "rx";
+					atmel,fifo-size = <16>;
+					status = "disabled";
+				};
+			};
+
+			sfr: sfr@f8050000 {
+				compatible = "microchip,sam9x7-sfr, microchip,sam9x60-sfr", "syscon";
+				reg = <0xf8050000 0x100>;
+			};
+
+			matrix: matrix@ffffde00 {
+				compatible = "microchip,sam9x7-matrix", "microchip,sam9x60-matrix", "atmel,at91sam9x5-matrix", "syscon";
+				reg = <0xffffde00 0x200>;
+			};
+
+			pmecc: ecc-engine@ffffe000 {
+				compatible = "microchip,sam9x7-pmecc", "microchip,sam9x60-pmecc", "atmel,at91sam9g45-pmecc";
+				reg = <0xffffe000 0x300>,
+				      <0xffffe600 0x100>;
+			};
+
+			mpddrc: mpddrc@ffffe800 {
+				compatible = "microchip,sam9x7-ddramc", "microchip,sam9x60-ddramc", "atmel,sama5d3-ddramc";
+				reg = <0xffffe800 0x200>;
+				clocks = <&pmc PMC_TYPE_SYSTEM 2>, <&pmc PMC_TYPE_CORE PMC_MCK>;
+				clock-names = "ddrck", "mpddr";
+			};
+
+			smc: smc@ffffea00 {
+				compatible = "microchip,sam9x7-smc", "microchip,sam9x60-smc", "atmel,at91sam9260-smc", "syscon";
+				reg = <0xffffea00 0x100>;
+			};
+
+			aic: interrupt-controller@fffff100 {
+				compatible = "microchip,sam9x7-aic";
+				reg = <0xfffff100 0x100>;
+				#interrupt-cells = <3>;
+				interrupt-controller;
+				atmel,external-irqs = <31>;
+			};
+
+			dbgu: serial@fffff200 {
+				compatible = "microchip,sam9x7-dbgu", "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+				reg = <0xfffff200 0x200>;
+				interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
+				dmas = <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(28))>,
+				       <&dma0
+					(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
+					 AT91_XDMAC_DT_PERID(29))>;
+				dma-names = "tx", "rx";
+				clocks = <&pmc PMC_TYPE_PERIPHERAL 47>;
+				clock-names = "usart";
+				status = "disabled";
+			};
+
+			pinctrl: pinctrl@fffff400 {
+				#address-cells = <1>;
+				#size-cells = <1>;
+				compatible = "microchip,sam9x7-pinctrl", "microchip,sam9x60-pinctrl", "atmel,at91sam9x5-pinctrl", "simple-mfd";
+				ranges = <0xfffff400 0xfffff400 0x800>;
+
+				/* mux-mask corresponding to sam9x7 SoC in TFBGA228L package */
+				atmel,mux-mask = <
+						 /*  A		B	   C	      D	  */
+						 0xffffffff 0xffffefc0 0xc0ffd000 0x00000000	/* pioA */
+						 0x07ffffff 0x0805fe7f 0x01ff9f80 0x06078000	/* pioB */
+						 0xffffffff 0x07dfffff 0xfa3fffff 0x00000000	/* pioC */
+						 0x00003fff 0x00003fe0 0x0000003f 0x00000000	/* pioD */
+						 >;
+
+				pioA: gpio@fffff400 {
+					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff400 0x200>;
+					interrupts = <2 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 2>;
+				};
+
+				pioB: gpio@fffff600 {
+					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff600 0x200>;
+					interrupts = <3 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					#gpio-lines = <26>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 3>;
+				};
+
+				pioC: gpio@fffff800 {
+					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffff800 0x200>;
+					interrupts = <4 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 4>;
+				};
+
+				pioD: gpio@fffffa00 {
+					compatible = "microchip,sam9x7-gpio", "microchip,sam9x60-gpio", "atmel,at91sam9x5-gpio", "atmel,at91rm9200-gpio";
+					reg = <0xfffffa00 0x200>;
+					interrupts = <44 IRQ_TYPE_LEVEL_HIGH 1>;
+					#gpio-cells = <2>;
+					gpio-controller;
+					#gpio-lines = <22>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+					clocks = <&pmc PMC_TYPE_PERIPHERAL 44>;
+				};
+			};
+
+			pmc: pmc@fffffc00 {
+				compatible = "microchip,sam9x7-pmc", "syscon";
+				reg = <0xfffffc00 0x200>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				#clock-cells = <2>;
+				clocks = <&clk32k 1>, <&clk32k 0>, <&main_xtal>;
+				clock-names = "td_slck", "md_slck", "main_xtal";
+			};
+
+			reset_controller: rstc@fffffe00 {
+				compatible = "microchip,sam9x7-rstc", "microchip,sam9x60-rstc";
+				reg = <0xfffffe00 0x10>;
+				clocks = <&clk32k 0>;
+			};
+
+			shutdown_controller: shdwc@fffffe10 {
+				compatible = "microchip,sam9x7-shdwc", "microchip,sam9x60-shdwc";
+				reg = <0xfffffe10 0x10>;
+				clocks = <&clk32k 0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				atmel,wakeup-rtc-timer;
+				atmel,wakeup-rtt-timer;
+				status = "disabled";
+			};
+
+			rtt: rtc@fffffe20 {
+				compatible = "microchip,sam9x7-rtt", "microchip,sam9x60-rtt", "atmel,at91sam9260-rtt";
+				reg = <0xfffffe20 0x20>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+			};
+
+			clk32k: sckc@fffffe50 {
+				compatible = "microchip,sam9x7-sckc", "microchip,sam9x60-sckc";
+				reg = <0xfffffe50 0x4>;
+				clocks = <&slow_xtal>;
+				#clock-cells = <1>;
+			};
+
+			gpbr: syscon@fffffe60 {
+				compatible = "microchip,sam9x7-gbpr", "microchip,sam9x60-gpbr", "atmel,at91sam9260-gpbr", "syscon";
+				reg = <0xfffffe60 0x10>;
+			};
+
+			rtc: rtc@fffffea8 {
+				compatible = "microchip,sam9x7-rtc", "microchip,sam9x60-rtc";
+				reg = <0xfffffea8 0x100>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+			};
+
+			watchdog: watchdog@ffffff80 {
+				compatible = "microchip,sam9x7-wdt", "microchip,sam9x60-wdt";
+				reg = <0xffffff80 0x24>;
+				interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
+				clocks = <&clk32k 0>;
+				status = "disabled";
+			};
+		};
+	};
+};