| Message ID | 1250188394-13121-1-git-send-email-sudhakar.raj@ti.com (mailing list archive) |
|---|---|
| State | Accepted |
| Headers | show |
Sudhakar Rajashekhara <sudhakar.raj@ti.com> writes: > This patch adds platform support for the graphic display > (Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM. > > Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Thanks, pushing today. KEvin > --- > Since the previous version: > 1. GPIO_TO_PIN macros are used to get the GPIO pin numbers. > 2. Removed call to gpio_free while exiting from da850_lcd_hw_init > function. > > This patch depends on the following patch which I have > submitted earlier: > [PATCH] davinci: Macro to convert GPIO signal to GPIO pin number > > arch/arm/mach-davinci/board-da850-evm.c | 50 +++++++++++++++++++++++ > arch/arm/mach-davinci/da850.c | 42 ++++++++++++++++++++ > arch/arm/mach-davinci/devices-da8xx.c | 59 ++++++++++++++++++++++++++++ > arch/arm/mach-davinci/include/mach/da8xx.h | 3 + > arch/arm/mach-davinci/include/mach/mux.h | 26 ++++++++++++ > 5 files changed, 180 insertions(+), 0 deletions(-) > > diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c > index 52bfe4c..b1df784 100644 > --- a/arch/arm/mach-davinci/board-da850-evm.c > +++ b/arch/arm/mach-davinci/board-da850-evm.c > @@ -17,6 +17,7 @@ > #include <linux/console.h> > #include <linux/i2c.h> > #include <linux/i2c/at24.h> > +#include <linux/gpio.h> > > #include <asm/mach-types.h> > #include <asm/mach/arch.h> > @@ -29,6 +30,9 @@ > #define DA850_EVM_PHY_MASK 0x1 > #define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ > > +#define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15) > +#define DA850_LCD_PWR_PIN GPIO_TO_PIN(8, 10) > + > static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = { > .bus_freq = 100, /* kHz */ > .bus_delay = 0, /* usec */ > @@ -59,6 +63,37 @@ static struct snd_platform_data da850_evm_snd_data = { > .rxnumevt = 1, > }; > > +static int da850_lcd_hw_init(void) > +{ > + int status; > + > + status = gpio_request(DA850_LCD_BL_PIN, "lcd bl\n"); > + if (status < 0) > + return status; > + > + status = gpio_request(DA850_LCD_PWR_PIN, "lcd pwr\n"); > + if (status < 0) { > + gpio_free(DA850_LCD_BL_PIN); > + return status; > + } > + > + gpio_direction_output(DA850_LCD_BL_PIN, 0); > + gpio_direction_output(DA850_LCD_PWR_PIN, 0); > + > + /* disable lcd backlight */ > + gpio_set_value(DA850_LCD_BL_PIN, 0); > + > + /* disable lcd power */ > + gpio_set_value(DA850_LCD_PWR_PIN, 0); > + > + /* enable lcd power */ > + gpio_set_value(DA850_LCD_PWR_PIN, 1); > + > + /* enable lcd backlight */ > + gpio_set_value(DA850_LCD_BL_PIN, 1); > + > + return 0; > +} > > static __init void da850_evm_init(void) > { > @@ -115,6 +150,21 @@ static __init void da850_evm_init(void) > ret); > > da8xx_init_mcasp(0, &da850_evm_snd_data); > + > + ret = da8xx_pinmux_setup(da850_lcdcntl_pins); > + if (ret) > + pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n", > + ret); > + > + ret = da850_lcd_hw_init(); > + if (ret) > + pr_warning("da850_evm_init: lcd initialization failed: %d\n", > + ret); > + > + ret = da8xx_register_lcdc(); > + if (ret) > + pr_warning("da850_evm_init: lcdc registration failed: %d\n", > + ret); > } > > #ifdef CONFIG_SERIAL_8250_CONSOLE > diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c > index e440c09..e6e605b 100644 > --- a/arch/arm/mach-davinci/da850.c > +++ b/arch/arm/mach-davinci/da850.c > @@ -297,6 +297,13 @@ static struct clk mcasp_clk = { > .psc_ctlr = 1, > }; > > +static struct clk lcdc_clk = { > + .name = "lcdc", > + .parent = &pll0_sysclk2, > + .lpsc = DA8XX_LPSC1_LCDC, > + .psc_ctlr = 1, > +}; > + > static struct davinci_clk da850_clks[] = { > CLK(NULL, "ref", &ref_clk), > CLK(NULL, "pll0", &pll0_clk), > @@ -335,6 +342,7 @@ static struct davinci_clk da850_clks[] = { > CLK(NULL, "rmii", &rmii_clk), > CLK("davinci_emac.1", NULL, &emac_clk), > CLK("davinci-mcasp.0", NULL, &mcasp_clk), > + CLK("da8xx_lcdc.0", NULL, &lcdc_clk), > CLK(NULL, NULL, NULL), > }; > > @@ -405,6 +413,30 @@ static const struct mux_config da850_pins[] = { > MUX_CFG(DA850, AXR_2, 2, 20, 15, 1, false) > MUX_CFG(DA850, AXR_1, 2, 24, 15, 1, false) > MUX_CFG(DA850, AXR_0, 2, 28, 15, 1, false) > + /* LCD function */ > + MUX_CFG(DA850, LCD_D_7, 16, 8, 15, 2, false) > + MUX_CFG(DA850, LCD_D_6, 16, 12, 15, 2, false) > + MUX_CFG(DA850, LCD_D_5, 16, 16, 15, 2, false) > + MUX_CFG(DA850, LCD_D_4, 16, 20, 15, 2, false) > + MUX_CFG(DA850, LCD_D_3, 16, 24, 15, 2, false) > + MUX_CFG(DA850, LCD_D_2, 16, 28, 15, 2, false) > + MUX_CFG(DA850, LCD_D_1, 17, 0, 15, 2, false) > + MUX_CFG(DA850, LCD_D_0, 17, 4, 15, 2, false) > + MUX_CFG(DA850, LCD_D_15, 17, 8, 15, 2, false) > + MUX_CFG(DA850, LCD_D_14, 17, 12, 15, 2, false) > + MUX_CFG(DA850, LCD_D_13, 17, 16, 15, 2, false) > + MUX_CFG(DA850, LCD_D_12, 17, 20, 15, 2, false) > + MUX_CFG(DA850, LCD_D_11, 17, 24, 15, 2, false) > + MUX_CFG(DA850, LCD_D_10, 17, 28, 15, 2, false) > + MUX_CFG(DA850, LCD_D_9, 18, 0, 15, 2, false) > + MUX_CFG(DA850, LCD_D_8, 18, 4, 15, 2, false) > + MUX_CFG(DA850, LCD_PCLK, 18, 24, 15, 2, false) > + MUX_CFG(DA850, LCD_HSYNC, 19, 0, 15, 2, false) > + MUX_CFG(DA850, LCD_VSYNC, 19, 4, 15, 2, false) > + MUX_CFG(DA850, NLCD_AC_ENB_CS, 19, 24, 15, 2, false) > + /* GPIO function */ > + MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false) > + MUX_CFG(DA850, GPIO8_10, 18, 28, 15, 8, false) > #endif > }; > > @@ -449,6 +481,16 @@ const short da850_mcasp_pins[] __initdata = { > -1 > }; > > +const short da850_lcdcntl_pins[] __initdata = { > + DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3, DA850_LCD_D_4, > + DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7, DA850_LCD_D_8, > + DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11, DA850_LCD_D_12, > + DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15, DA850_LCD_PCLK, > + DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS, DA850_GPIO2_15, > + DA850_GPIO8_10, > + -1 > +}; > + > /* FIQ are pri 0-1; otherwise 2-7, with 7 lowest priority */ > static u8 da850_default_priorities[DA850_N_CP_INTC_IRQ] = { > [IRQ_DA8XX_COMMTX] = 7, > diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c > index 1882eef..094eb8e 100644 > --- a/arch/arm/mach-davinci/devices-da8xx.c > +++ b/arch/arm/mach-davinci/devices-da8xx.c > @@ -21,6 +21,7 @@ > #include <mach/common.h> > #include <mach/time.h> > #include <mach/da8xx.h> > +#include <video/da8xx-fb.h> > > #include "clock.h" > > @@ -353,3 +354,61 @@ void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata) > platform_device_register(&da850_mcasp_device); > } > } > + > +static const struct display_panel disp_panel = { > + QVGA, > + 16, > + 16, > + COLOR_ACTIVE, > +}; > + > +static struct lcd_ctrl_config lcd_cfg = { > + &disp_panel, > + .ac_bias = 255, > + .ac_bias_intrpt = 0, > + .dma_burst_sz = 16, > + .bpp = 16, > + .fdd = 255, > + .tft_alt_mode = 0, > + .stn_565_mode = 0, > + .mono_8bit_mode = 0, > + .invert_line_clock = 1, > + .invert_frm_clock = 1, > + .sync_edge = 0, > + .sync_ctrl = 1, > + .raster_order = 0, > +}; > + > +static struct da8xx_lcdc_platform_data da850_evm_lcdc_pdata = { > + .manu_name = "sharp", > + .controller_data = &lcd_cfg, > + .type = "Sharp_LK043T1DG01", > +}; > + > +static struct resource da8xx_lcdc_resources[] = { > + [0] = { /* registers */ > + .start = DA8XX_LCD_CNTRL_BASE, > + .end = DA8XX_LCD_CNTRL_BASE + SZ_4K - 1, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { /* interrupt */ > + .start = IRQ_DA8XX_LCDINT, > + .end = IRQ_DA8XX_LCDINT, > + .flags = IORESOURCE_IRQ, > + }, > +}; > + > +static struct platform_device da850_lcdc_device = { > + .name = "da8xx_lcdc", > + .id = 0, > + .num_resources = ARRAY_SIZE(da8xx_lcdc_resources), > + .resource = da8xx_lcdc_resources, > + .dev = { > + .platform_data = &da850_evm_lcdc_pdata, > + } > +}; > + > +int __init da8xx_register_lcdc(void) > +{ > + return platform_device_register(&da850_lcdc_device); > +} > diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h > index 30c5c40..0af3fb6 100644 > --- a/arch/arm/mach-davinci/include/mach/da8xx.h > +++ b/arch/arm/mach-davinci/include/mach/da8xx.h > @@ -37,6 +37,7 @@ > #define DA8XX_TIMER64P1_BASE 0x01c21000 > #define DA8XX_GPIO_BASE 0x01e26000 > #define DA8XX_PSC1_BASE 0x01e27000 > +#define DA8XX_LCD_CNTRL_BASE 0x01e13000 > > #define PINMUX0 0x00 > #define PINMUX1 0x04 > @@ -66,6 +67,7 @@ int da8xx_register_edma(void); > int da8xx_register_i2c(int instance, struct davinci_i2c_platform_data *pdata); > int da8xx_register_watchdog(void); > int da8xx_register_emac(void); > +int da8xx_register_lcdc(void); > void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata); > > extern struct platform_device da8xx_serial_device; > @@ -103,6 +105,7 @@ extern const short da850_i2c0_pins[]; > extern const short da850_i2c1_pins[]; > extern const short da850_cpgmac_pins[]; > extern const short da850_mcasp_pins[]; > +extern const short da850_lcdcntl_pins[]; > > int da8xx_pinmux_setup(const short pins[]); > > diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h > index 82d7514..30bf329 100644 > --- a/arch/arm/mach-davinci/include/mach/mux.h > +++ b/arch/arm/mach-davinci/include/mach/mux.h > @@ -775,6 +775,32 @@ enum davinci_da850_index { > DA850_AXR_2, > DA850_AXR_1, > DA850_AXR_0, > + > + /* LCD function */ > + DA850_LCD_D_7, > + DA850_LCD_D_6, > + DA850_LCD_D_5, > + DA850_LCD_D_4, > + DA850_LCD_D_3, > + DA850_LCD_D_2, > + DA850_LCD_D_1, > + DA850_LCD_D_0, > + DA850_LCD_D_15, > + DA850_LCD_D_14, > + DA850_LCD_D_13, > + DA850_LCD_D_12, > + DA850_LCD_D_11, > + DA850_LCD_D_10, > + DA850_LCD_D_9, > + DA850_LCD_D_8, > + DA850_LCD_PCLK, > + DA850_LCD_HSYNC, > + DA850_LCD_VSYNC, > + DA850_NLCD_AC_ENB_CS, > + > + /* GPIO function */ > + DA850_GPIO2_15, > + DA850_GPIO8_10, > }; > > #ifdef CONFIG_DAVINCI_MUX > -- > 1.5.6 > > _______________________________________________ > Davinci-linux-open-source mailing list > Davinci-linux-open-source@linux.davincidsp.com > http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
diff --git a/arch/arm/mach-davinci/board-da850-evm.c b/arch/arm/mach-davinci/board-da850-evm.c index 52bfe4c..b1df784 100644 --- a/arch/arm/mach-davinci/board-da850-evm.c +++ b/arch/arm/mach-davinci/board-da850-evm.c @@ -17,6 +17,7 @@ #include <linux/console.h> #include <linux/i2c.h> #include <linux/i2c/at24.h> +#include <linux/gpio.h> #include <asm/mach-types.h> #include <asm/mach/arch.h> @@ -29,6 +30,9 @@ #define DA850_EVM_PHY_MASK 0x1 #define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */ +#define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15) +#define DA850_LCD_PWR_PIN GPIO_TO_PIN(8, 10) + static struct davinci_i2c_platform_data da850_evm_i2c_0_pdata = { .bus_freq = 100, /* kHz */ .bus_delay = 0, /* usec */ @@ -59,6 +63,37 @@ static struct snd_platform_data da850_evm_snd_data = { .rxnumevt = 1, }; +static int da850_lcd_hw_init(void) +{ + int status; + + status = gpio_request(DA850_LCD_BL_PIN, "lcd bl\n"); + if (status < 0) + return status; + + status = gpio_request(DA850_LCD_PWR_PIN, "lcd pwr\n"); + if (status < 0) { + gpio_free(DA850_LCD_BL_PIN); + return status; + } + + gpio_direction_output(DA850_LCD_BL_PIN, 0); + gpio_direction_output(DA850_LCD_PWR_PIN, 0); + + /* disable lcd backlight */ + gpio_set_value(DA850_LCD_BL_PIN, 0); + + /* disable lcd power */ + gpio_set_value(DA850_LCD_PWR_PIN, 0); + + /* enable lcd power */ + gpio_set_value(DA850_LCD_PWR_PIN, 1); + + /* enable lcd backlight */ + gpio_set_value(DA850_LCD_BL_PIN, 1); + + return 0; +} static __init void da850_evm_init(void) { @@ -115,6 +150,21 @@ static __init void da850_evm_init(void) ret); da8xx_init_mcasp(0, &da850_evm_snd_data); + + ret = da8xx_pinmux_setup(da850_lcdcntl_pins); + if (ret) + pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n", + ret); + + ret = da850_lcd_hw_init(); + if (ret) + pr_warning("da850_evm_init: lcd initialization failed: %d\n", + ret); + + ret = da8xx_register_lcdc(); + if (ret) + pr_warning("da850_evm_init: lcdc registration failed: %d\n", + ret); } #ifdef CONFIG_SERIAL_8250_CONSOLE diff --git a/arch/arm/mach-davinci/da850.c b/arch/arm/mach-davinci/da850.c index e440c09..e6e605b 100644 --- a/arch/arm/mach-davinci/da850.c +++ b/arch/arm/mach-davinci/da850.c @@ -297,6 +297,13 @@ static struct clk mcasp_clk = { .psc_ctlr = 1, }; +static struct clk lcdc_clk = { + .name = "lcdc", + .parent = &pll0_sysclk2, + .lpsc = DA8XX_LPSC1_LCDC, + .psc_ctlr = 1, +}; + static struct davinci_clk da850_clks[] = { CLK(NULL, "ref", &ref_clk), CLK(NULL, "pll0", &pll0_clk), @@ -335,6 +342,7 @@ static struct davinci_clk da850_clks[] = { CLK(NULL, "rmii", &rmii_clk), CLK("davinci_emac.1", NULL, &emac_clk), CLK("davinci-mcasp.0", NULL, &mcasp_clk), + CLK("da8xx_lcdc.0", NULL, &lcdc_clk), CLK(NULL, NULL, NULL), }; @@ -405,6 +413,30 @@ static const struct mux_config da850_pins[] = { MUX_CFG(DA850, AXR_2, 2, 20, 15, 1, false) MUX_CFG(DA850, AXR_1, 2, 24, 15, 1, false) MUX_CFG(DA850, AXR_0, 2, 28, 15, 1, false) + /* LCD function */ + MUX_CFG(DA850, LCD_D_7, 16, 8, 15, 2, false) + MUX_CFG(DA850, LCD_D_6, 16, 12, 15, 2, false) + MUX_CFG(DA850, LCD_D_5, 16, 16, 15, 2, false) + MUX_CFG(DA850, LCD_D_4, 16, 20, 15, 2, false) + MUX_CFG(DA850, LCD_D_3, 16, 24, 15, 2, false) + MUX_CFG(DA850, LCD_D_2, 16, 28, 15, 2, false) + MUX_CFG(DA850, LCD_D_1, 17, 0, 15, 2, false) + MUX_CFG(DA850, LCD_D_0, 17, 4, 15, 2, false) + MUX_CFG(DA850, LCD_D_15, 17, 8, 15, 2, false) + MUX_CFG(DA850, LCD_D_14, 17, 12, 15, 2, false) + MUX_CFG(DA850, LCD_D_13, 17, 16, 15, 2, false) + MUX_CFG(DA850, LCD_D_12, 17, 20, 15, 2, false) + MUX_CFG(DA850, LCD_D_11, 17, 24, 15, 2, false) + MUX_CFG(DA850, LCD_D_10, 17, 28, 15, 2, false) + MUX_CFG(DA850, LCD_D_9, 18, 0, 15, 2, false) + MUX_CFG(DA850, LCD_D_8, 18, 4, 15, 2, false) + MUX_CFG(DA850, LCD_PCLK, 18, 24, 15, 2, false) + MUX_CFG(DA850, LCD_HSYNC, 19, 0, 15, 2, false) + MUX_CFG(DA850, LCD_VSYNC, 19, 4, 15, 2, false) + MUX_CFG(DA850, NLCD_AC_ENB_CS, 19, 24, 15, 2, false) + /* GPIO function */ + MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false) + MUX_CFG(DA850, GPIO8_10, 18, 28, 15, 8, false) #endif }; @@ -449,6 +481,16 @@ const short da850_mcasp_pins[] __initdata = { -1 }; +const short da850_lcdcntl_pins[] __initdata = { + DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3, DA850_LCD_D_4, + DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7, DA850_LCD_D_8, + DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11, DA850_LCD_D_12, + DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15, DA850_LCD_PCLK, + DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS, DA850_GPIO2_15, + DA850_GPIO8_10, + -1 +}; + /* FIQ are pri 0-1; otherwise 2-7, with 7 lowest priority */ static u8 da850_default_priorities[DA850_N_CP_INTC_IRQ] = { [IRQ_DA8XX_COMMTX] = 7, diff --git a/arch/arm/mach-davinci/devices-da8xx.c b/arch/arm/mach-davinci/devices-da8xx.c index 1882eef..094eb8e 100644 --- a/arch/arm/mach-davinci/devices-da8xx.c +++ b/arch/arm/mach-davinci/devices-da8xx.c @@ -21,6 +21,7 @@ #include <mach/common.h> #include <mach/time.h> #include <mach/da8xx.h> +#include <video/da8xx-fb.h> #include "clock.h" @@ -353,3 +354,61 @@ void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata) platform_device_register(&da850_mcasp_device); } } + +static const struct display_panel disp_panel = { + QVGA, + 16, + 16, + COLOR_ACTIVE, +}; + +static struct lcd_ctrl_config lcd_cfg = { + &disp_panel, + .ac_bias = 255, + .ac_bias_intrpt = 0, + .dma_burst_sz = 16, + .bpp = 16, + .fdd = 255, + .tft_alt_mode = 0, + .stn_565_mode = 0, + .mono_8bit_mode = 0, + .invert_line_clock = 1, + .invert_frm_clock = 1, + .sync_edge = 0, + .sync_ctrl = 1, + .raster_order = 0, +}; + +static struct da8xx_lcdc_platform_data da850_evm_lcdc_pdata = { + .manu_name = "sharp", + .controller_data = &lcd_cfg, + .type = "Sharp_LK043T1DG01", +}; + +static struct resource da8xx_lcdc_resources[] = { + [0] = { /* registers */ + .start = DA8XX_LCD_CNTRL_BASE, + .end = DA8XX_LCD_CNTRL_BASE + SZ_4K - 1, + .flags = IORESOURCE_MEM, + }, + [1] = { /* interrupt */ + .start = IRQ_DA8XX_LCDINT, + .end = IRQ_DA8XX_LCDINT, + .flags = IORESOURCE_IRQ, + }, +}; + +static struct platform_device da850_lcdc_device = { + .name = "da8xx_lcdc", + .id = 0, + .num_resources = ARRAY_SIZE(da8xx_lcdc_resources), + .resource = da8xx_lcdc_resources, + .dev = { + .platform_data = &da850_evm_lcdc_pdata, + } +}; + +int __init da8xx_register_lcdc(void) +{ + return platform_device_register(&da850_lcdc_device); +} diff --git a/arch/arm/mach-davinci/include/mach/da8xx.h b/arch/arm/mach-davinci/include/mach/da8xx.h index 30c5c40..0af3fb6 100644 --- a/arch/arm/mach-davinci/include/mach/da8xx.h +++ b/arch/arm/mach-davinci/include/mach/da8xx.h @@ -37,6 +37,7 @@ #define DA8XX_TIMER64P1_BASE 0x01c21000 #define DA8XX_GPIO_BASE 0x01e26000 #define DA8XX_PSC1_BASE 0x01e27000 +#define DA8XX_LCD_CNTRL_BASE 0x01e13000 #define PINMUX0 0x00 #define PINMUX1 0x04 @@ -66,6 +67,7 @@ int da8xx_register_edma(void); int da8xx_register_i2c(int instance, struct davinci_i2c_platform_data *pdata); int da8xx_register_watchdog(void); int da8xx_register_emac(void); +int da8xx_register_lcdc(void); void __init da8xx_init_mcasp(int id, struct snd_platform_data *pdata); extern struct platform_device da8xx_serial_device; @@ -103,6 +105,7 @@ extern const short da850_i2c0_pins[]; extern const short da850_i2c1_pins[]; extern const short da850_cpgmac_pins[]; extern const short da850_mcasp_pins[]; +extern const short da850_lcdcntl_pins[]; int da8xx_pinmux_setup(const short pins[]); diff --git a/arch/arm/mach-davinci/include/mach/mux.h b/arch/arm/mach-davinci/include/mach/mux.h index 82d7514..30bf329 100644 --- a/arch/arm/mach-davinci/include/mach/mux.h +++ b/arch/arm/mach-davinci/include/mach/mux.h @@ -775,6 +775,32 @@ enum davinci_da850_index { DA850_AXR_2, DA850_AXR_1, DA850_AXR_0, + + /* LCD function */ + DA850_LCD_D_7, + DA850_LCD_D_6, + DA850_LCD_D_5, + DA850_LCD_D_4, + DA850_LCD_D_3, + DA850_LCD_D_2, + DA850_LCD_D_1, + DA850_LCD_D_0, + DA850_LCD_D_15, + DA850_LCD_D_14, + DA850_LCD_D_13, + DA850_LCD_D_12, + DA850_LCD_D_11, + DA850_LCD_D_10, + DA850_LCD_D_9, + DA850_LCD_D_8, + DA850_LCD_PCLK, + DA850_LCD_HSYNC, + DA850_LCD_VSYNC, + DA850_NLCD_AC_ENB_CS, + + /* GPIO function */ + DA850_GPIO2_15, + DA850_GPIO8_10, }; #ifdef CONFIG_DAVINCI_MUX
This patch adds platform support for the graphic display (Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> --- Since the previous version: 1. GPIO_TO_PIN macros are used to get the GPIO pin numbers. 2. Removed call to gpio_free while exiting from da850_lcd_hw_init function. This patch depends on the following patch which I have submitted earlier: [PATCH] davinci: Macro to convert GPIO signal to GPIO pin number arch/arm/mach-davinci/board-da850-evm.c | 50 +++++++++++++++++++++++ arch/arm/mach-davinci/da850.c | 42 ++++++++++++++++++++ arch/arm/mach-davinci/devices-da8xx.c | 59 ++++++++++++++++++++++++++++ arch/arm/mach-davinci/include/mach/da8xx.h | 3 + arch/arm/mach-davinci/include/mach/mux.h | 26 ++++++++++++ 5 files changed, 180 insertions(+), 0 deletions(-)