@@ -32,12 +32,13 @@
#include <mach/cp_intc.h>
#include <mach/da8xx.h>
#include <mach/nand.h>
+#include <mach/mux.h>
#define DA850_EVM_PHY_MASK 0x1
#define DA850_EVM_MDIO_FREQUENCY 2200000 /* PHY bus frequency */
+#define DA850_LCD_PWR_PIN GPIO_TO_PIN(2, 8)
#define DA850_LCD_BL_PIN GPIO_TO_PIN(2, 15)
-#define DA850_LCD_PWR_PIN GPIO_TO_PIN(8, 10)
#define DA850_MMCSD_CD_PIN GPIO_TO_PIN(4, 0)
#define DA850_MMCSD_WP_PIN GPIO_TO_PIN(4, 1)
@@ -264,6 +265,11 @@ static void __init da850_evm_init_nor(void)
#define HAS_MMC 0
#endif
+static const short da850_evm_lcdc_pins[] = {
+ DA850_GPIO2_8, DA850_GPIO2_15,
+ -1
+};
+
static __init void da850_evm_init(void)
{
struct davinci_soc_info *soc_info = &davinci_soc_info;
@@ -372,6 +378,12 @@ static __init void da850_evm_init(void)
pr_warning("da850_evm_init: lcdcntl mux setup failed: %d\n",
ret);
+ /* Handle board specific muxing for LCD here */
+ ret = da8xx_pinmux_setup(da850_evm_lcdc_pins);
+ if (ret)
+ pr_warning("da850_evm_init: evm specific lcd mux setup "
+ "failed: %d\n", ret);
+
ret = da850_lcd_hw_init();
if (ret)
pr_warning("da850_evm_init: lcd initialization failed: %d\n",
@@ -513,8 +513,8 @@ static const struct mux_config da850_pins[] = {
MUX_CFG(DA850, EMA_WAIT_1, 6, 24, 15, 1, false)
MUX_CFG(DA850, NEMA_CS_2, 7, 0, 15, 1, false)
/* GPIO function */
+ MUX_CFG(DA850, GPIO2_8, 5, 28, 15, 8, false)
MUX_CFG(DA850, GPIO2_15, 5, 0, 15, 8, false)
- MUX_CFG(DA850, GPIO8_10, 18, 28, 15, 8, false)
MUX_CFG(DA850, GPIO4_0, 10, 28, 15, 8, false)
MUX_CFG(DA850, GPIO4_1, 10, 24, 15, 8, false)
#endif
@@ -562,12 +562,11 @@ const short da850_mcasp_pins[] __initdata = {
};
const short da850_lcdcntl_pins[] __initdata = {
- DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3, DA850_LCD_D_4,
- DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7, DA850_LCD_D_8,
- DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11, DA850_LCD_D_12,
- DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15, DA850_LCD_PCLK,
- DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS, DA850_GPIO2_15,
- DA850_GPIO8_10,
+ DA850_LCD_D_0, DA850_LCD_D_1, DA850_LCD_D_2, DA850_LCD_D_3,
+ DA850_LCD_D_4, DA850_LCD_D_5, DA850_LCD_D_6, DA850_LCD_D_7,
+ DA850_LCD_D_8, DA850_LCD_D_9, DA850_LCD_D_10, DA850_LCD_D_11,
+ DA850_LCD_D_12, DA850_LCD_D_13, DA850_LCD_D_14, DA850_LCD_D_15,
+ DA850_LCD_PCLK, DA850_LCD_HSYNC, DA850_LCD_VSYNC, DA850_NLCD_AC_ENB_CS,
-1
};
@@ -872,8 +872,8 @@ enum davinci_da850_index {
DA850_NEMA_CS_2,
/* GPIO function */
+ DA850_GPIO2_8,
DA850_GPIO2_15,
- DA850_GPIO8_10,
DA850_GPIO4_0,
DA850_GPIO4_1,
};
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin number of LCD panel power has changed. This patch takes care of this change. Software will support only Beta versions of DA850/OMAP-L138 EVM. In the process, add the missing entry for data pin 0 and remove the GPIO specific pins from da850_lcdcntl_pins structure. EVM specific muxing for LCD is being done in the board file now. Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> --- Since the previous version: 1. Added an entry for the EVM specific LCD pins. 2. Configuring the pins using da8xx_pinmux_setup() instead of calling davinci_cfg_reg() directly. arch/arm/mach-davinci/board-da850-evm.c | 14 +++++++++++++- arch/arm/mach-davinci/da850.c | 13 ++++++------- arch/arm/mach-davinci/include/mach/mux.h | 2 +- 3 files changed, 20 insertions(+), 9 deletions(-)