diff mbox

[2.6.31-rc7] spi: davinci spi driver

Message ID 200908271858.48850.david-b@pacbell.net (mailing list archive)
State Accepted
Headers show

Commit Message

David Brownell Aug. 28, 2009, 1:58 a.m. UTC
From: Sandeep Paulraj <s-paulraj@ti.com>

The patch adds a SPI driver for DaVinci series SOC's.

[dbrownell@users.sourceforge.net: fixes and cleanup]

Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
---
 arch/arm/mach-davinci/include/mach/spi.h |   45 +
 drivers/spi/Kconfig                      |    7 
 drivers/spi/Makefile                     |    1 
 drivers/spi/davinci_spi.c                |  757 +++++++++++++++++++++++++++++
 drivers/spi/davinci_spi.h                |  163 ++++++
 5 files changed, 973 insertions(+)

Comments

Sergei Shtylyov Aug. 28, 2009, 9:01 a.m. UTC | #1
Hello.

David Brownell wrote:

> From: Sandeep Paulraj <s-paulraj@ti.com>
>
> The patch adds a SPI driver for DaVinci series SOC's.
>
> [dbrownell@users.sourceforge.net: fixes and cleanup]
>
> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
>   

  This patch lacks MV people's signoffs (and MV copyright on the driver).

WBR, Sergei
David Brownell Aug. 28, 2009, 9:21 a.m. UTC | #2
On Friday 28 August 2009, Sergei Shtylyov wrote:
> Hello.
> 
> David Brownell wrote:
> 
> > From: Sandeep Paulraj <s-paulraj@ti.com>
> >
> > The patch adds a SPI driver for DaVinci series SOC's.
> >
> > [dbrownell@users.sourceforge.net: fixes and cleanup]
> >
> > Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
> > Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
> >   
> 
>   This patch lacks MV people's signoffs (and MV copyright on the driver).

-ENOPATCH

I don't recall seeing any version with MV attributions, FWIW.
Sergei Shtylyov Aug. 28, 2009, 10:09 a.m. UTC | #3
Hello.

David Brownell wrote:

>>> From: Sandeep Paulraj <s-paulraj@ti.com>
>>>
>>> The patch adds a SPI driver for DaVinci series SOC's.
>>>
>>> [dbrownell@users.sourceforge.net: fixes and cleanup]
>>>
>>> Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
>>> Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
>>>   
>>>       
>>   This patch lacks MV people's signoffs (and MV copyright on the driver).
>>     
>
> -ENOPATCH
>
> I don't recall seeing any version with MV attributions, FWIW.

   Because there was none. :-)
   I have just mailed Sandeep about this yesterday.

WBR, Sergei
s-paulraj@ti.com Aug. 28, 2009, 10:29 a.m. UTC | #4
Sergei, Dave,

When i started this SPI process many moons ago, i am absolutely sure that i sent out e-mails on our internal TI MV mailing list asking for the appropriate signoffs. I can dig out the e-mails but i don't see what can be achieved on doing that. I did not get any responses then.

Obviously that time the driver was not ready for submission and now seems an auspicious time.

I'll take care of all pending issues, i.e signoffs, copyright(which as pointed out was not present in the original driver) and send the patch.

Thanks,
Sandeep
Siegbert Baude Sept. 1, 2009, 3:01 p.m. UTC | #5
David Brownell wrote:
> The patch adds a SPI driver for DaVinci series SOC's.


Hello David and Sandeep

Just some comments to your driver.

Why are you talking about 32 bit transfer? I don't know all devices this driver
is meant for, but at least DM355 has only up to 16bits.

> + * davinci_spi_setup_transfer - This functions will determine transfer method
> + * @spi: spi device on which data transfer to be done
> + * @t: spi transfer in which transfer info is filled
> + *
> + * This function determines data transfer method (8/16/32 bit transfer).

[snip]
See also here:

> +	/*
> +	 * Assign function pointer to appropriate transfer method
> +	 * 8bit, 16bit or 32bit transfer
> +	 */



A question to using a division in "davinci_spi_bufs_pio":

> +	conv = davinci_spi->slave[spi->chip_select].bytes_per_word;
> +	davinci_spi->count = t->len / conv;

I'm not sure, if the compiler manages to detect that "bytes_per_word" can be
only 1 or 2 and uses shifts? Divisions are quite slow.



Did you read the silicon errata for DM355, sprz264d? At least the error checks
should be done special, and CS can cause trouble, too, as described on p.15ff.

As a side note unrelated to SPI: Does anybody know, if the kernel works around
"Concurrent Access to ARM Internal Memory May Result in Access Errors" (p.14 of
sprz264d)?


Best regards
Siegbert
s-paulraj@ti.com Sept. 1, 2009, 3:15 p.m. UTC | #6
> 
> David Brownell wrote:
> > The patch adds a SPI driver for DaVinci series SOC's.
> 
> 
> Hello David and Sandeep
> 
> Just some comments to your driver.
> 
> Why are you talking about 32 bit transfer? I don't know all devices this
> driver
> is meant for, but at least DM355 has only up to 16bits.
[Sandeep] you are correct. The comment is incorrect. The driver though support only upto 16 bit
> 
> > + * davinci_spi_setup_transfer - This functions will determine transfer
> method
> > + * @spi: spi device on which data transfer to be done
> > + * @t: spi transfer in which transfer info is filled
> > + *
> > + * This function determines data transfer method (8/16/32 bit
> transfer).
> 
> [snip]
> See also here:
> 
> > +	/*
> > +	 * Assign function pointer to appropriate transfer method
> > +	 * 8bit, 16bit or 32bit transfer
> > +	 */
[Sandeep] right comment is in accurate again
> 
> 
> 
> A question to using a division in "davinci_spi_bufs_pio":
> 
> > +	conv = davinci_spi->slave[spi->chip_select].bytes_per_word;
> > +	davinci_spi->count = t->len / conv;
> 
> I'm not sure, if the compiler manages to detect that "bytes_per_word" can
> be
> only 1 or 2 and uses shifts? Divisions are quite slow.
[Sandeep] I am told that the compiler that we use (the latest CodeSourcery) is smart enough to detect this.
> 
> 
> 
> Did you read the silicon errata for DM355, sprz264d? At least the error
> checks
> should be done special, and CS can cause trouble, too, as described on
> p.15ff.
[Sandeep] In the initial support we are not addressing a lot of stuff related to CS. This will be done in follow up patches
> 
> As a side note unrelated to SPI: Does anybody know, if the kernel works
> around
> "Concurrent Access to ARM Internal Memory May Result in Access Errors"
> (p.14 of
> sprz264d)?
> 
> 
> Best regards
> Siegbert
> 
> 
> _______________________________________________
> Davinci-linux-open-source mailing list
> Davinci-linux-open-source@linux.davincidsp.com
> http://linux.davincidsp.com/mailman/listinfo/davinci-linux-open-source
diff mbox

Patch

--- /dev/null
+++ b/arch/arm/mach-davinci/include/mach/spi.h
@@ -0,0 +1,45 @@ 
+/*
+ * Copyright 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+ */
+
+#ifndef __ARCH_ARM_DAVINCI_SPI_H
+#define __ARCH_ARM_DAVINCI_SPI_H
+
+#define SPI_INTERN_CS	0xFF
+
+enum {
+	SPI_VERSION_1, /* For DM355/DM365/DM6467*/
+	SPI_VERSION_2, /* For DA8xx */
+};
+
+struct davinci_spi_platform_data {
+	u8	version;
+	u16	num_chipselect;
+	u32	wdelay;
+	u32	odd_parity;
+	u32	parity_enable;
+	u32	wait_enable;
+	u32	timer_disable;
+	u32	clk_internal;
+	u32	cs_hold;
+	u32	intr_level;
+	u32	poll_mode;
+	u8	c2tdelay;
+	u8	t2cdelay;
+};
+
+#endif	/* __ARCH_ARM_DAVINCI_SPI_H */
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -77,6 +77,13 @@  config SPI_AU1550
 	  This driver can also be built as a module.  If so, the module
 	  will be called au1550_spi.
 
+config SPI_DAVINCI
+	tristate "SPI controller driver for DaVinci/DA8xx SoC's"
+	depends on SPI_MASTER && ARCH_DAVINCI
+	select SPI_BITBANG
+	help
+	  SPI master controller for DaVinci and DA8xx SPI modules.
+
 config SPI_BITBANG
 	tristate "Utilities for Bitbanging SPI masters"
 	help
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -16,6 +16,7 @@  obj-$(CONFIG_SPI_BFIN)			+= spi_bfin5xx.
 obj-$(CONFIG_SPI_BITBANG)		+= spi_bitbang.o
 obj-$(CONFIG_SPI_AU1550)		+= au1550_spi.o
 obj-$(CONFIG_SPI_BUTTERFLY)		+= spi_butterfly.o
+obj-$(CONFIG_SPI_DAVINCI)		+= davinci_spi.o
 obj-$(CONFIG_SPI_GPIO)			+= spi_gpio.o
 obj-$(CONFIG_SPI_IMX)			+= mxc_spi.o
 obj-$(CONFIG_SPI_LM70_LLP)		+= spi_lm70llp.o
--- /dev/null
+++ b/drivers/spi/davinci_spi.c
@@ -0,0 +1,757 @@ 
+/*
+ * Copyright (C) 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/module.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/err.h>
+#include <linux/clk.h>
+
+#include <linux/spi/spi.h>
+#include <linux/spi/spi_bitbang.h>
+
+#include <mach/spi.h>
+
+#include "davinci_spi.h"
+
+
+static void davinci_spi_rx_buf_u8(u32 data, struct davinci_spi *davinci_spi)
+{
+	u8 *rx = davinci_spi->rx;
+
+	*rx++ = (u8)data;
+	davinci_spi->rx = rx;
+}
+
+static void davinci_spi_rx_buf_u16(u32 data, struct davinci_spi *davinci_spi)
+{
+	u16 *rx = davinci_spi->rx;
+
+	*rx++ = (u16)data;
+	davinci_spi->rx = rx;
+}
+
+static u32 davinci_spi_tx_buf_u8(struct davinci_spi *davinci_spi)
+{
+	u32 data;
+	const u8 *tx = davinci_spi->tx;
+
+	data = *tx++;
+	davinci_spi->tx = tx;
+	return data;
+}
+
+static u32 davinci_spi_tx_buf_u16(struct davinci_spi *davinci_spi)
+{
+	u32 data;
+	const u16 *tx = davinci_spi->tx;
+
+	data = *tx++;
+	davinci_spi->tx = tx;
+	return data;
+}
+
+static inline void set_io_bits(void __iomem *addr, u32 bits)
+{
+	u32 v = ioread32(addr);
+
+	v |= bits;
+	iowrite32(v, addr);
+}
+
+static inline void clear_io_bits(void __iomem *addr, u32 bits)
+{
+	u32 v = ioread32(addr);
+
+	v &= ~bits;
+	iowrite32(v, addr);
+}
+
+static inline void set_fmt_bits(void __iomem *addr, u32 bits, int cs_num)
+{
+	set_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits);
+}
+
+static inline void clear_fmt_bits(void __iomem *addr, u32 bits, int cs_num)
+{
+	clear_io_bits(addr + SPIFMT0 + (0x4 * cs_num), bits);
+}
+
+/*
+ * Interface to control the chip select signal
+ */
+static void davinci_spi_chipselect(struct spi_device *spi, int value)
+{
+	struct davinci_spi *davinci_spi;
+	struct davinci_spi_platform_data *pdata;
+	u32 data1_reg_val = 0;
+
+	davinci_spi = spi_master_get_devdata(spi->master);
+	pdata = davinci_spi->pdata;
+
+	/*
+	 * Board specific chip select logic decides the polarity and cs
+	 * line for the controller
+	 */
+	if (value == BITBANG_CS_INACTIVE) {
+		set_io_bits(davinci_spi->base + SPIDEF, CS_DEFAULT);
+
+		data1_reg_val |= CS_DEFAULT << SPIDAT1_CSNR_SHIFT;
+		iowrite32(data1_reg_val, davinci_spi->base + SPIDAT1);
+
+		while ((ioread32(davinci_spi->base + SPIBUF)
+					& SPIBUF_RXEMPTY_MASK) == 0)
+			cpu_relax();
+	}
+}
+
+/*
+ * davinci_spi_setup_transfer - This functions will determine transfer method
+ * @spi: spi device on which data transfer to be done
+ * @t: spi transfer in which transfer info is filled
+ *
+ * This function determines data transfer method (8/16/32 bit transfer).
+ * It will also set the SPI Clock Control register according to
+ * SPI slave device freq.
+ */
+static int davinci_spi_setup_transfer(struct spi_device *spi,
+		struct spi_transfer *t)
+{
+
+	struct davinci_spi *davinci_spi;
+	struct davinci_spi_platform_data *pdata;
+	u8 bits_per_word = 0;
+	u32 hz = 0, prescale;
+
+	davinci_spi = spi_master_get_devdata(spi->master);
+	pdata = davinci_spi->pdata;
+
+	if (t) {
+		bits_per_word = t->bits_per_word;
+		hz = t->speed_hz;
+	}
+
+	/* if bits_per_word is not set then set it default */
+	if (!bits_per_word)
+		bits_per_word = spi->bits_per_word;
+
+	/*
+	 * Assign function pointer to appropriate transfer method
+	 * 8bit, 16bit or 32bit transfer
+	 */
+	if (bits_per_word <= 8 && bits_per_word >= 2) {
+		davinci_spi->get_rx = davinci_spi_rx_buf_u8;
+		davinci_spi->get_tx = davinci_spi_tx_buf_u8;
+		davinci_spi->slave[spi->chip_select].bytes_per_word = 1;
+	} else if (bits_per_word <= 16 && bits_per_word >= 2) {
+		davinci_spi->get_rx = davinci_spi_rx_buf_u16;
+		davinci_spi->get_tx = davinci_spi_tx_buf_u16;
+		davinci_spi->slave[spi->chip_select].bytes_per_word = 2;
+	} else
+		return -EINVAL;
+
+	if (!hz)
+		hz = spi->max_speed_hz;
+
+	clear_fmt_bits(davinci_spi->base, SPIFMT_CHARLEN_MASK,
+			spi->chip_select);
+	set_fmt_bits(davinci_spi->base, bits_per_word & 0x1f,
+			spi->chip_select);
+
+	prescale = ((clk_get_rate(davinci_spi->clk) / hz) - 1) & 0xff;
+
+	clear_fmt_bits(davinci_spi->base, 0x0000ff00, spi->chip_select);
+	set_fmt_bits(davinci_spi->base, prescale << 8, spi->chip_select);
+
+	return 0;
+}
+
+/*
+ * davinci_spi_setup - This functions will set default transfer method
+ * @spi: spi device on which data transfer to be done
+ *
+ * This functions sets the default transfer method.
+ */
+
+static int davinci_spi_setup(struct spi_device *spi)
+{
+	int retval;
+	struct davinci_spi *davinci_spi;
+
+	davinci_spi = spi_master_get_devdata(spi->master);
+
+	/*
+	 * SPI in DaVinci and DA8xx operate between
+	 * 600 KHz and 50 MHz
+	 */
+	if (spi->max_speed_hz < 600000 || spi->max_speed_hz > 50000000)
+		return -EINVAL;
+
+	/*
+	 * Set up SPIFMTn register, unique to this chipselect.
+	 *
+	 * NOTE: we could do all of these with one write.  Also, some
+	 * of the "version 2" features are found in chips that don't
+	 * support all of them...
+	 */
+	if (spi->mode & SPI_LSB_FIRST)
+		set_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK,
+				spi->chip_select);
+	else
+		clear_fmt_bits(davinci_spi->base, SPIFMT_SHIFTDIR_MASK,
+				spi->chip_select);
+
+	if (spi->mode & SPI_CPOL)
+		set_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK,
+				spi->chip_select);
+	else
+		clear_fmt_bits(davinci_spi->base, SPIFMT_POLARITY_MASK,
+				spi->chip_select);
+
+	if (!(spi->mode & SPI_CPHA))
+		set_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK,
+				spi->chip_select);
+	else
+		clear_fmt_bits(davinci_spi->base, SPIFMT_PHASE_MASK,
+				spi->chip_select);
+
+	/*
+	 * Version 1 hardware supports two basic SPI modes:
+	 *  - Standard SPI mode uses 4 pins, with chipselect
+	 *  - 3 pin SPI is a 4 pin variant without CS (SPI_NO_CS)
+	 *	(distinct from SPI_3WIRE, with just one data wire;
+	 *	or similar variants without MOSI or without MISO)
+	 *
+	 * Version 2 hardware supports an optional handshaking signal,
+	 * so it can support two more modes:
+	 *  - 5 pin SPI variant is standard SPI plus SPI_READY
+	 *  - 4 pin with enable is (SPI_READY | SPI_NO_CS)
+	 */
+
+	if (davinci_spi->version == SPI_VERSION_2) {
+		clear_fmt_bits(davinci_spi->base, SPIFMT_WDELAY_MASK,
+				spi->chip_select);
+		set_fmt_bits(davinci_spi->base,
+				(davinci_spi->pdata->wdelay
+						<< SPIFMT_WDELAY_SHIFT)
+					& SPIFMT_WDELAY_MASK,
+				spi->chip_select);
+
+		if (davinci_spi->pdata->odd_parity)
+			set_fmt_bits(davinci_spi->base,
+					SPIFMT_ODD_PARITY_MASK,
+					spi->chip_select);
+		else
+			clear_fmt_bits(davinci_spi->base,
+					SPIFMT_ODD_PARITY_MASK,
+					spi->chip_select);
+
+		if (davinci_spi->pdata->parity_enable)
+			set_fmt_bits(davinci_spi->base,
+					SPIFMT_PARITYENA_MASK,
+					spi->chip_select);
+		else
+			clear_fmt_bits(davinci_spi->base,
+					SPIFMT_PARITYENA_MASK,
+					spi->chip_select);
+
+		if (davinci_spi->pdata->wait_enable)
+			set_fmt_bits(davinci_spi->base,
+					SPIFMT_WAITENA_MASK,
+					spi->chip_select);
+		else
+			clear_fmt_bits(davinci_spi->base,
+					SPIFMT_WAITENA_MASK,
+					spi->chip_select);
+
+		if (davinci_spi->pdata->timer_disable)
+			set_fmt_bits(davinci_spi->base,
+					SPIFMT_DISTIMER_MASK,
+					spi->chip_select);
+		else
+			clear_fmt_bits(davinci_spi->base,
+					SPIFMT_DISTIMER_MASK,
+					spi->chip_select);
+	}
+
+	retval = davinci_spi_setup_transfer(spi, NULL);
+
+	return retval;
+}
+
+static int davinci_spi_bufs_prep(struct spi_device *spi,
+				 struct davinci_spi *davinci_spi)
+{
+	int op_mode = 0;
+
+	/*
+	 * REVISIT  unless devices disagree about SPI_LOOP or
+	 * SPI_READY (SPI_NO_CS only allows one device!), this
+	 * should not need to be done before each message...
+	 * optimize for both flags staying cleared.
+	 */
+
+	op_mode = SPIPC0_DIFUN_MASK
+		| SPIPC0_DOFUN_MASK
+		| SPIPC0_CLKFUN_MASK;
+	if (!(spi->mode & SPI_NO_CS))
+		op_mode |= 1 << spi->chip_select;
+	if (spi->mode & SPI_READY)
+		op_mode |= SPIPC0_SPIENA_MASK;
+
+	iowrite32(op_mode, davinci_spi->base + SPIPC0);
+
+	if (spi->mode & SPI_LOOP)
+		set_io_bits(davinci_spi->base + SPIGCR1,
+				SPIGCR1_LOOPBACK_MASK);
+	else
+		clear_io_bits(davinci_spi->base + SPIGCR1,
+				SPIGCR1_LOOPBACK_MASK);
+
+	return 0;
+}
+
+static int davinci_spi_check_error(struct davinci_spi *davinci_spi,
+				   int int_status)
+{
+	struct device *sdev = davinci_spi->bitbang.master->dev.parent;
+
+	if (int_status & SPIFLG_TIMEOUT_MASK) {
+		dev_dbg(sdev, "SPI Time-out Error\n");
+		return -ETIMEDOUT;
+	}
+	if (int_status & SPIFLG_DESYNC_MASK) {
+		dev_dbg(sdev, "SPI Desynchronization Error\n");
+		return -EIO;
+	}
+	if (int_status & SPIFLG_BITERR_MASK) {
+		dev_dbg(sdev, "SPI Bit error\n");
+		return -EIO;
+	}
+
+	if (davinci_spi->version == SPI_VERSION_2) {
+		if (int_status & SPIFLG_DLEN_ERR_MASK) {
+			dev_dbg(sdev, "SPI Data Length Error\n");
+			return -EIO;
+		}
+		if (int_status & SPIFLG_PARERR_MASK) {
+			dev_dbg(sdev, "SPI Parity Error\n");
+			return -EIO;
+		}
+		if (int_status & SPIFLG_OVRRUN_MASK) {
+			dev_dbg(sdev, "SPI Data Overrun error\n");
+			return -EIO;
+		}
+		if (int_status & SPIFLG_TX_INTR_MASK) {
+			dev_dbg(sdev, "SPI TX intr bit set\n");
+			return -EIO;
+		}
+		if (int_status & SPIFLG_BUF_INIT_ACTIVE_MASK) {
+			dev_dbg(sdev, "SPI Buffer Init Active\n");
+			return -EBUSY;
+		}
+	}
+
+	return 0;
+}
+
+/*
+ * davinci_spi_bufs - functions which will handle transfer data
+ * @spi: spi device on which data transfer to be done
+ * @t: spi transfer in which transfer info is filled
+ *
+ * This function will put data to be transferred into data register
+ * of SPI controller and then wait untill the completion will be marked
+ * by the IRQ Handler.
+ */
+static int davinci_spi_bufs_pio(struct spi_device *spi, struct spi_transfer *t)
+{
+	struct davinci_spi *davinci_spi;
+	int int_status, count, ret;
+	u8 conv, tmp;
+	u32 tx_data, data1_reg_val;
+	u32 buf_val, flg_val;
+	struct davinci_spi_platform_data *pdata;
+
+	davinci_spi = spi_master_get_devdata(spi->master);
+	pdata = davinci_spi->pdata;
+
+	davinci_spi->tx = t->tx_buf;
+	davinci_spi->rx = t->rx_buf;
+
+	/* convert len to words bbased on bits_per_word */
+	conv = davinci_spi->slave[spi->chip_select].bytes_per_word;
+	davinci_spi->count = t->len / conv;
+
+	INIT_COMPLETION(davinci_spi->done);
+
+	ret = davinci_spi_bufs_prep(spi, davinci_spi);
+	if (ret)
+		return ret;
+
+	/* Enable SPI */
+	set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_SPIENA_MASK);
+
+	iowrite32(0 | (pdata->c2tdelay << SPI_C2TDELAY_SHIFT) |
+			(pdata->t2cdelay << SPI_T2CDELAY_SHIFT),
+			davinci_spi->base + SPIDELAY);
+
+	count = davinci_spi->count;
+	data1_reg_val = pdata->cs_hold << SPIDAT1_CSHOLD_SHIFT;
+	tmp = ~(0x1 << spi->chip_select);
+
+	clear_io_bits(davinci_spi->base + SPIDEF, ~tmp);
+
+	data1_reg_val |= tmp << SPIDAT1_CSNR_SHIFT;
+
+	while ((ioread32(davinci_spi->base + SPIBUF)
+				& SPIBUF_RXEMPTY_MASK) == 0)
+		cpu_relax();
+
+	/* Determine the command to execute READ or WRITE */
+	if (t->tx_buf) {
+		clear_io_bits(davinci_spi->base + SPIINT, SPIINT_MASKALL);
+
+		while (1) {
+			tx_data = davinci_spi->get_tx(davinci_spi);
+
+			data1_reg_val &= ~(0xFFFF);
+			data1_reg_val |= (0xFFFF & tx_data);
+
+			buf_val = ioread32(davinci_spi->base + SPIBUF);
+			if ((buf_val & SPIBUF_TXFULL_MASK) == 0) {
+				iowrite32(data1_reg_val,
+						davinci_spi->base + SPIDAT1);
+
+				count--;
+			}
+			while (ioread32(davinci_spi->base + SPIBUF)
+					& SPIBUF_RXEMPTY_MASK)
+				cpu_relax();
+
+			/* getting the returned byte */
+			if (t->rx_buf) {
+				buf_val = ioread32(davinci_spi->base + SPIBUF);
+				davinci_spi->get_rx(buf_val, davinci_spi);
+			}
+			if (count <= 0)
+				break;
+		}
+	} else {
+		if (pdata->poll_mode) {
+			while (1) {
+				/* keeps the serial clock going */
+				if ((ioread32(davinci_spi->base + SPIBUF)
+						& SPIBUF_TXFULL_MASK) == 0)
+					iowrite32(data1_reg_val,
+						davinci_spi->base + SPIDAT1);
+
+				while (ioread32(davinci_spi->base + SPIBUF) &
+						SPIBUF_RXEMPTY_MASK)
+					cpu_relax();
+
+				flg_val = ioread32(davinci_spi->base + SPIFLG);
+				buf_val = ioread32(davinci_spi->base + SPIBUF);
+
+				davinci_spi->get_rx(buf_val, davinci_spi);
+
+				count--;
+				if (count <= 0)
+					break;
+			}
+		} else {	/* Receive in Interrupt mode */
+			int i;
+
+			for (i = 0; i < davinci_spi->count; i++) {
+				set_io_bits(davinci_spi->base + SPIINT,
+						SPIINT_BITERR_INTR
+						| SPIINT_OVRRUN_INTR
+						| SPIINT_RX_INTR);
+
+				iowrite32(data1_reg_val,
+						davinci_spi->base + SPIDAT1);
+
+				while (ioread32(davinci_spi->base + SPIINT) &
+						SPIINT_RX_INTR)
+					cpu_relax();
+			}
+			iowrite32((data1_reg_val & 0x0ffcffff),
+					davinci_spi->base + SPIDAT1);
+		}
+	}
+
+	/*
+	 * Check for bit error, desync error,parity error,timeout error and
+	 * receive overflow errors
+	 */
+	int_status = ioread32(davinci_spi->base + SPIFLG);
+
+	ret = davinci_spi_check_error(davinci_spi, int_status);
+	if (ret != 0)
+		return ret;
+
+	/* SPI Framework maintains the count only in bytes so convert back */
+	davinci_spi->count *= conv;
+
+	return t->len;
+}
+
+/*
+ * davinci_spi_irq - probe function for SPI Master Controller
+ * @irq: IRQ number for this SPI Master
+ * @context_data: structure for SPI Master controller davinci_spi
+ *
+ * ISR will determine that interrupt arrives either for READ or WRITE command.
+ * According to command it will do the appropriate action. It will check
+ * transfer length and if it is not zero then dispatch transfer command again.
+ * If transfer length is zero then it will indicate the COMPLETION so that
+ * davinci_spi_bufs function can go ahead.
+ */
+static irqreturn_t davinci_spi_irq(s32 irq, void *context_data)
+{
+	struct davinci_spi *davinci_spi = context_data;
+	u32 int_status, rx_data = 0;
+	irqreturn_t ret = IRQ_NONE;
+
+	int_status = ioread32(davinci_spi->base + SPIFLG);
+	while ((int_status & SPIFLG_MASK) != 0) {
+		ret = IRQ_HANDLED;
+
+		if (likely(int_status & SPIFLG_RX_INTR_MASK)) {
+			rx_data = ioread32(davinci_spi->base + SPIBUF);
+			davinci_spi->get_rx(rx_data, davinci_spi);
+
+			/* Disable Receive Interrupt */
+			iowrite32(~SPIINT_RX_INTR,
+					davinci_spi->base + SPIINT);
+		} else
+			(void)davinci_spi_check_error(davinci_spi, int_status);
+
+		int_status = ioread32(davinci_spi->base + SPIFLG);
+	}
+
+	return ret;
+}
+
+/*
+ * davinci_spi_probe - probe function for SPI Master Controller
+ * @pdev: platform_device structure which contains plateform specific data
+ *
+ * According to Linux Device Model this function will be invoked by Linux
+ * with plateform_device struct which contains the device specific info.
+ * This function will map the SPI controller's memory, register IRQ,
+ * Reset SPI controller and setting its registers to default value.
+ * It will invoke spi_bitbang_start to create work queue so that client driver
+ * can register transfer method to work queue.
+ */
+static int davinci_spi_probe(struct platform_device *pdev)
+{
+	struct spi_master *master;
+	struct davinci_spi *davinci_spi;
+	struct davinci_spi_platform_data *pdata;
+	struct resource *r, *mem;
+	int ret = 0;
+
+	pdata = pdev->dev.platform_data;
+	if (pdata == NULL) {
+		ret = -ENODEV;
+		goto err;
+	}
+
+	master = spi_alloc_master(&pdev->dev, sizeof(struct davinci_spi));
+	if (master == NULL) {
+		ret = -ENOMEM;
+		goto err;
+	}
+
+	dev_set_drvdata(&pdev->dev, master);
+
+	davinci_spi = spi_master_get_devdata(master);
+	if (davinci_spi == NULL) {
+		ret = -ENOENT;
+		goto free_master;
+	}
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (r == NULL) {
+		ret = -ENOENT;
+		goto free_master;
+	}
+
+	davinci_spi->pbase = r->start;
+	davinci_spi->region_size = resource_size(r);
+	davinci_spi->pdata = pdata;
+
+	mem = request_mem_region(r->start, davinci_spi->region_size,
+					pdev->name);
+	if (mem == NULL) {
+		ret = -EBUSY;
+		goto free_master;
+	}
+
+	davinci_spi->base = (struct davinci_spi_reg __iomem *)
+			ioremap(r->start, davinci_spi->region_size);
+	if (davinci_spi->base == NULL) {
+		ret = -ENOMEM;
+		goto release_region;
+	}
+
+	davinci_spi->irq = platform_get_irq(pdev, 0);
+	if (davinci_spi->irq <= 0) {
+		ret = -EINVAL;
+		goto unmap_io;
+	}
+
+	ret = request_irq(davinci_spi->irq, davinci_spi_irq, IRQF_DISABLED,
+			  dev_name(&pdev->dev), davinci_spi);
+	if (ret != 0) {
+		ret = -EAGAIN;
+		goto unmap_io;
+	}
+
+	davinci_spi->bitbang.master = spi_master_get(master);
+	if (davinci_spi->bitbang.master == NULL) {
+		ret = -ENODEV;
+		goto err1;
+	}
+
+	davinci_spi->clk = clk_get(&pdev->dev, NULL);
+	if (IS_ERR(davinci_spi->clk)) {
+		ret = -ENODEV;
+		goto put_master;
+	}
+	clk_enable(davinci_spi->clk);
+
+
+	master->bus_num = pdev->id;
+	master->num_chipselect = pdata->num_chipselect;
+	master->setup = davinci_spi_setup;
+
+	davinci_spi->bitbang.chipselect = davinci_spi_chipselect;
+	davinci_spi->bitbang.setup_transfer = davinci_spi_setup_transfer;
+	davinci_spi->bitbang.txrx_bufs = davinci_spi_bufs_pio;
+
+	davinci_spi->bitbang.flags = SPI_NO_CS | SPI_LSB_FIRST | SPI_LOOP;
+	if (davinci_spi->version == SPI_VERSION_2)
+		davinci_spi->bitbang.flags |= SPI_READY;
+
+	davinci_spi->version = pdata->version;
+	davinci_spi->get_rx = davinci_spi_rx_buf_u8;
+	davinci_spi->get_tx = davinci_spi_tx_buf_u8;
+
+	init_completion(&davinci_spi->done);
+
+	/* Reset In/OUT SPI module */
+	iowrite32(0, davinci_spi->base + SPIGCR0);
+	udelay(100);
+	iowrite32(1, davinci_spi->base + SPIGCR0);
+
+	/* Clock internal */
+	if (davinci_spi->pdata->clk_internal)
+		set_io_bits(davinci_spi->base + SPIGCR1,
+				SPIGCR1_CLKMOD_MASK);
+	else
+		clear_io_bits(davinci_spi->base + SPIGCR1,
+				SPIGCR1_CLKMOD_MASK);
+
+	/* master mode default */
+	set_io_bits(davinci_spi->base + SPIGCR1, SPIGCR1_MASTER_MASK);
+
+	if (davinci_spi->pdata->intr_level)
+		iowrite32(SPI_INTLVL_1, davinci_spi->base + SPILVL);
+	else
+		iowrite32(SPI_INTLVL_0, davinci_spi->base + SPILVL);
+
+	ret = spi_bitbang_start(&davinci_spi->bitbang);
+	if (ret != 0)
+		goto free_clk;
+
+	dev_info(&pdev->dev, "Controller at 0x%p (irq = %d) \n",
+		davinci_spi->base, davinci_spi->irq);
+
+	return ret;
+
+free_clk:
+	clk_disable(davinci_spi->clk);
+	clk_put(davinci_spi->clk);
+put_master:
+	spi_master_put(master);
+err1:
+	free_irq(davinci_spi->irq, davinci_spi);
+unmap_io:
+	iounmap(davinci_spi->base);
+release_region:
+	release_mem_region(davinci_spi->pbase, davinci_spi->region_size);
+free_master:
+	kfree(master);
+err:
+	return ret;
+}
+
+/*
+ * davinci_spi_remove - remove function for SPI Master Controller
+ * @pdev: platform_device structure which contains plateform specific data
+ *
+ * This function will do the reverse action of davinci_spi_probe function
+ * It will free the IRQ and SPI controller's memory region.
+ * It will also call spi_bitbang_stop to destroy the work queue which was
+ * created by spi_bitbang_start.
+ */
+static int __exit davinci_spi_remove(struct platform_device *pdev)
+{
+	struct davinci_spi *davinci_spi;
+	struct spi_master *master;
+
+	master = dev_get_drvdata(&pdev->dev);
+	davinci_spi = spi_master_get_devdata(master);
+
+	spi_bitbang_stop(&davinci_spi->bitbang);
+
+	clk_disable(davinci_spi->clk);
+	clk_put(davinci_spi->clk);
+	spi_master_put(master);
+	free_irq(davinci_spi->irq, davinci_spi);
+	iounmap(davinci_spi->base);
+	release_mem_region(davinci_spi->pbase, davinci_spi->region_size);
+
+	return 0;
+}
+
+static struct platform_driver davinci_spi_driver = {
+	.driver.name = "spi_davinci",
+	.remove = __exit_p(davinci_spi_remove),
+};
+
+static int __init davinci_spi_init(void)
+{
+	return platform_driver_probe(&davinci_spi_driver, davinci_spi_probe);
+}
+
+static void __exit davinci_spi_exit(void)
+{
+	platform_driver_unregister(&davinci_spi_driver);
+}
+
+module_init(davinci_spi_init);
+module_exit(davinci_spi_exit);
+
+MODULE_DESCRIPTION("TI DaVinci SPI Master Controller Driver");
+MODULE_LICENSE("GPL");
--- /dev/null
+++ b/drivers/spi/davinci_spi.h
@@ -0,0 +1,163 @@ 
+/*
+ * Copyright (C) 2009 Texas Instruments.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __DAVINCI_SPI_H
+#define __DAVINCI_SPI_H
+
+#define SPI_MAX_CHIPSELECT	2
+
+#define CS_DEFAULT	0xFF
+#define SCS0_SELECT	0x01
+#define SCS1_SELECT	0x02
+#define SCS2_SELECT	0x04
+#define SCS3_SELECT	0x08
+#define SCS4_SELECT	0x10
+#define SCS5_SELECT	0x20
+#define SCS6_SELECT	0x40
+#define SCS7_SELECT	0x80
+
+#define SPIFMT_PHASE_MASK	BIT(16)
+#define SPIFMT_POLARITY_MASK	BIT(17)
+#define SPIFMT_DISTIMER_MASK	BIT(18)
+#define SPIFMT_SHIFTDIR_MASK	BIT(20)
+#define SPIFMT_WAITENA_MASK	BIT(21)
+#define SPIFMT_PARITYENA_MASK	BIT(22)
+#define SPIFMT_ODD_PARITY_MASK	BIT(23)
+#define SPIFMT_WDELAY_MASK	0x3f000000u
+#define SPIFMT_WDELAY_SHIFT	24
+#define SPIFMT_CHARLEN_MASK	0x0000001Fu
+
+/* SPIGCR1 */
+#define SPIGCR1_SPIENA_MASK	0x01000000u
+
+/* SPIPC0 */
+#define SPIPC0_DIFUN_MASK	BIT(11)		/* MISO */
+#define SPIPC0_DOFUN_MASK	BIT(10)		/* MOSI */
+#define SPIPC0_CLKFUN_MASK	BIT(9)		/* CLK */
+#define SPIPC0_SPIENA_MASK	BIT(8)		/* nREADY */
+#define SPIPC0_EN1FUN_MASK	BIT(1)
+#define SPIPC0_EN0FUN_MASK	BIT(0)
+
+#define SPIINT_MASKALL		0x0101035F
+#define SPI_INTLVL_1		0x000001FFu
+#define SPI_INTLVL_0		0x00000000u
+
+/* SPIDAT1 */
+#define SPIDAT1_CSHOLD_MASK	BIT(28)
+#define SPIDAT1_CSHOLD_SHIFT	28
+#define SPIDAT1_CSNR_MASK	(BIT(17 | BIT(16))
+#define SPIDAT1_CSNR_SHIFT	16
+#define SPIDAT1_DFSEL_MASK	(BIT(24 | BIT(25))
+#define SPIGCR1_CLKMOD_MASK	BIT(1)
+#define SPIGCR1_MASTER_MASK     BIT(0)
+#define SPIGCR1_LOOPBACK_MASK	BIT(16)
+
+/* SPIBUF */
+#define SPIBUF_TXFULL_MASK	BIT(29)
+#define SPIBUF_RXEMPTY_MASK	BIT(31)
+
+/* Error Masks */
+#define SPIFLG_DLEN_ERR_MASK		BIT(0)
+#define SPIFLG_TIMEOUT_MASK		BIT(1)
+#define SPIFLG_PARERR_MASK		BIT(2)
+#define SPIFLG_DESYNC_MASK		BIT(3)
+#define SPIFLG_BITERR_MASK		BIT(4)
+#define SPIFLG_OVRRUN_MASK		BIT(6)
+#define SPIFLG_RX_INTR_MASK		BIT(8)
+#define SPIFLG_TX_INTR_MASK		BIT(9)
+#define SPIFLG_BUF_INIT_ACTIVE_MASK	BIT(24)
+#define SPIFLG_MASK			(SPIFLG_DLEN_ERR_MASK \
+				| SPIFLG_TIMEOUT_MASK | SPIFLG_PARERR_MASK \
+				| SPIFLG_DESYNC_MASK | SPIFLG_BITERR_MASK \
+				| SPIFLG_OVRRUN_MASK | SPIFLG_RX_INTR_MASK \
+				| SPIFLG_TX_INTR_MASK \
+				| SPIFLG_BUF_INIT_ACTIVE_MASK)
+
+#define SPIINT_DLEN_ERR_INTR	BIT(0)
+#define SPIINT_TIMEOUT_INTR	BIT(1)
+#define SPIINT_PARERR_INTR	BIT(2)
+#define SPIINT_DESYNC_INTR	BIT(3)
+#define SPIINT_BITERR_INTR	BIT(4)
+#define SPIINT_OVRRUN_INTR	BIT(6)
+#define SPIINT_RX_INTR		BIT(8)
+#define SPIINT_TX_INTR		BIT(9)
+#define SPIINT_DMA_REQ_EN	BIT(16)
+#define SPIINT_ENABLE_HIGHZ	BIT(24)
+
+#define SPI_T2CDELAY_SHIFT	16
+#define SPI_C2TDELAY_SHIFT	24
+
+/* SPI Controller registers */
+#define SPIGCR0		0x00
+#define SPIGCR1		0x04
+#define SPIINT		0x08
+#define SPILVL		0x0c
+#define SPIFLG		0x10
+#define SPIPC0		0x14
+#define SPIPC1		0x18
+#define SPIPC2		0x1c
+#define SPIPC3		0x20
+#define SPIPC4		0x24
+#define SPIPC5		0x28
+#define SPIPC6		0x2c
+#define SPIPC7		0x30
+#define SPIPC8		0x34
+#define SPIDAT0		0x38
+#define SPIDAT1		0x3c
+#define SPIBUF		0x40
+#define SPIEMU		0x44
+#define SPIDELAY	0x48
+#define SPIDEF		0x4c
+#define SPIFMT0		0x50
+#define SPIFMT1		0x54
+#define SPIFMT2		0x58
+#define SPIFMT3		0x5c
+#define TGINTVEC0	0x60
+#define TGINTVEC1	0x64
+
+struct davinci_spi_slave {
+	u32	cmd_to_write;
+	u32	clk_ctrl_to_write;
+	u32	bytes_per_word;
+	u8	active_cs;
+};
+
+/* SPI Controller driver's private data. */
+struct davinci_spi {
+	struct spi_bitbang	bitbang;
+	struct clk		*clk;
+
+	u8			version;
+	resource_size_t		pbase;
+	void __iomem		*base;
+	size_t			region_size;
+	u32			irq;
+	struct completion	done;
+
+	const void		*tx;
+	void			*rx;
+	int			count;
+	struct			davinci_spi_platform_data *pdata;
+
+	void			(*get_rx)(u32 rx_data, struct davinci_spi *);
+	u32			(*get_tx)(struct davinci_spi *);
+
+	struct davinci_spi_slave slave[SPI_MAX_CHIPSELECT];
+};
+
+#endif /* __DAVINCI_SPI_H */