diff mbox

[v4,2/2] dmaengine: Add ADM driver

Message ID 1423719965-8156-3-git-send-email-agross@codeaurora.org (mailing list archive)
State Changes Requested
Headers show

Commit Message

Andy Gross Feb. 12, 2015, 5:46 a.m. UTC
Add the DMA engine driver for the QCOM Application Data Mover (ADM) DMA
controller found in the MSM8x60 and IPQ/APQ8064 platforms.

The ADM supports both memory to memory transactions and memory
to/from peripheral device transactions.  The controller also provides flow
control capabilities for transactions to/from peripheral devices.

The initial release of this driver supports slave transfers to/from peripherals
and also incorporates CRCI (client rate control interface) flow control.

Signed-off-by: Andy Gross <agross@codeaurora.org>
---
 drivers/dma/Kconfig    |   10 +
 drivers/dma/Makefile   |    1 +
 drivers/dma/qcom_adm.c |  901 ++++++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 912 insertions(+)
 create mode 100644 drivers/dma/qcom_adm.c

Comments

Vinod Koul March 13, 2015, 8:57 a.m. UTC | #1
On Wed, Feb 11, 2015 at 11:46:05PM -0600, Andy Gross wrote:
> +++ b/drivers/dma/qcom_adm.c
> @@ -0,0 +1,901 @@
> +/*
> + * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
shouldn't this be 15 :)

 +/* ADM registers - calculated from channel number and security domain */
> +#define HI_CH_CMD_PTR(chan, ee)		(4*chan + 0x20800*ee)
> +#define HI_CH_RSLT(chan, ee)		(0x40 + 4*chan + 0x20800*ee)
> +#define HI_CH_FLUSH_STATE0(chan, ee)	(0x80 + 4*chan + 0x20800*ee)
> +#define HI_CH_FLUSH_STATE1(chan, ee)	(0xc0 + 4*chan + 0x20800*ee)
> +#define HI_CH_FLUSH_STATE2(chan, ee)	(0x100 + 4*chan + 0x20800*ee)
> +#define HI_CH_FLUSH_STATE3(chan, ee)	(0x140 + 4*chan + 0x20800*ee)
> +#define HI_CH_FLUSH_STATE4(chan, ee)	(0x180 + 4*chan + 0x20800*ee)
> +#define HI_CH_FLUSH_STATE5(chan, ee)	(0x1c0 + 4*chan + 0x20800*ee)
> +#define HI_CH_STATUS_SD(chan, ee)	(0x200 + 4*chan + 0x20800*ee)
> +#define HI_CH_CONF(chan)		(0x240 + 4*chan)
> +#define HI_CH_RSLT_CONF(chan, ee)	(0x300 + 4*chan + 0x20800*ee)
> +#define HI_SEC_DOMAIN_IRQ_STATUS(ee)	(0x380 + 0x20800*ee)
> +#define HI_CI_CONF(ci)			(0x390 + 4*ci)
> +#define HI_CRCI_CONF0			0x3d0
> +#define HI_CRCI_CONF1			0x3d4
> +#define HI_GP_CTL			0x3d8
> +#define HI_CRCI_CTL(crci, ee)		(0x400 + 0x4*crci + 0x20800*ee)
two things, one the names are quite generic and may cause conflicts so pls
fix that. Second the values, what is the deal with 4*chan, should that be a
define as well. Also rather than copy pasting a macros would be better for
this expansion

> +
> +/* channel status */
> +#define CH_STATUS_VALID	BIT(1)
> +
> +/* channel result */
> +#define CH_RSLT_VALID	BIT(31)
> +#define CH_RSLT_ERR	BIT(3)
> +#define CH_RSLT_FLUSH	BIT(2)
> +#define CH_RSLT_TPD	BIT(1)
> +
> +/* channel conf */
> +#define CH_CONF_MPU_DISABLE	BIT(11)
> +#define CH_CONF_PERM_MPU_CONF	BIT(9)
> +#define CH_CONF_FLUSH_RSLT_EN	BIT(8)
> +#define CH_CONF_FORCE_RSLT_EN	BIT(7)
> +#define CH_CONF_IRQ_EN		BIT(6)
> +
> +/* channel result conf */
> +#define CH_RSLT_CONF_FLUSH_EN	BIT(1)
> +#define CH_RSLT_CONF_IRQ_EN	BIT(0)
> +
> +/* CRCI CTL */
> +#define CRCI_CTL_MUX_SEL	BIT(18)
> +#define CRCI_CTL_RST		BIT(17)
> +
> +/* CI configuration */
> +#define CI_RANGE_END(x)		(x << 24)
> +#define CI_RANGE_START(x)	(x << 16)
> +#define CI_BURST_4_WORDS	0x4
> +#define CI_BURST_8_WORDS	0x8
shouldn't you be consistent is usage of BIT()

> +
> +/* GP CTL */
> +#define GP_CTL_LP_EN		BIT(12)
> +#define GP_CTL_LP_CNT(x)	(x << 8)
> +
> +/* Command pointer list entry */
> +#define CPLE_LP			BIT(31)
> +#define CPLE_CMD_PTR_LIST	BIT(29)
> +
> +/* Command list entry */
> +#define CMD_LC			BIT(31)
> +#define CMD_DST_CRCI(n)		(((n) & 0xf) << 7)
> +#define CMD_SRC_CRCI(n)		(((n) & 0xf) << 3)
> +
> +#define CMD_TYPE_SINGLE		0x0
> +#define CMD_TYPE_BOX		0x3a
naming issues...
> +static int adm_alloc_chan(struct dma_chan *chan)
> +{
> +	return 0;
> +}
This is no longer mandatory, so can be dropped

> +static int adm_get_blksize(unsigned int burst)
> +{
> +	int ret;
> +
> +	switch (burst) {
> +	case 16:
> +		ret = 0;
> +		break;
> +	case 32:
> +		ret = 1;
> +		break;
> +	case 64:
> +		ret = 2;
> +		break;
> +	case 128:
> +		ret = 3;
> +		break;
> +	case 192:
> +		ret = 4;
> +		break;
> +	case 256:
> +		ret = 5;
> +		break;
ffs(burst>>4) ?

> +static struct dma_async_tx_descriptor *adm_prep_slave_sg(struct dma_chan *chan,
> +	struct scatterlist *sgl, unsigned int sg_len,
> +	enum dma_transfer_direction direction, unsigned long flags,
> +	void *context)
> +{
> +	struct adm_chan *achan = to_adm_chan(chan);
> +	struct adm_device *adev = achan->adev;
> +	struct adm_async_desc *async_desc;
> +	struct scatterlist *sg;
> +	u32 i;
> +	u32 single_count = 0, box_count = 0, desc_offset = 0, crci = 0;
> +	struct adm_desc_hw_box *box_desc;
> +	struct adm_desc_hw_single *single_desc;
> +	void *desc;
> +	u32 *cple, *last_cmd;
> +	u32 burst;
> +	int blk_size = 0;
> +
> +
> +	if (!is_slave_direction(direction)) {
> +		dev_err(adev->dev, "invalid dma direction\n");
> +		return NULL;
> +	}
> +
> +	/*
> +	 * get burst value from slave configuration
> +	 * If zero, default to maximum burst size
> +	 * If larger than the max transfer size, set to ADM_MAX_XFER
> +	 */
> +	burst = (direction == DMA_MEM_TO_DEV) ?
> +		achan->slave.dst_maxburst :
> +		achan->slave.src_maxburst;
> +
> +	if (!burst || burst > ADM_MAX_XFER)
> +		burst = ADM_MAX_XFER;
For slave, we should send error here. The DMA settings are matched with
slave FIFO, so any change here can cause issues

> +
> +	/* if using flow control, validate burst and crci values */
> +	if (achan->slave.device_fc) {
> +
> +		blk_size = adm_get_blksize(burst);
> +		if (blk_size < 0) {
> +			dev_err(adev->dev, "invalid burst value w/ crci: %d\n",
> +				burst);
> +			return ERR_PTR(-EINVAL);
> +		}
> +
> +		crci = achan->slave.slave_id & 0xf;
> +		if (!crci || achan->slave.slave_id > 0x1f) {
> +			dev_err(adev->dev, "invalid crci value\n");
> +			return ERR_PTR(-EINVAL);
> +		}
> +	}
> +
> +	/* iterate through sgs and compute allocation size of structures */
> +	for_each_sg(sgl, sg, sg_len, i)
> +		if (sg_dma_len(sg) % burst)
> +			single_count += DIV_ROUND_UP(sg_dma_len(sg), burst);
> +		else
> +			box_count += DIV_ROUND_UP(sg_dma_len(sg) / burst,
> +							ADM_MAX_ROWS);
> +
> +	async_desc = kzalloc(sizeof(*async_desc), GFP_NOWAIT);
> +	if (!async_desc)
> +		return ERR_PTR(-ENOMEM);
> +
> +	if (crci)
> +		async_desc->mux = achan->slave.slave_id >> 4 ?
> +					CRCI_CTL_MUX_SEL : 0;
> +	async_desc->crci = crci;
> +	async_desc->blk_size = blk_size;
> +	async_desc->dma_len = single_count * sizeof(*single_desc) +
> +				box_count * sizeof(*box_desc) + sizeof(*cple) +
> +				2*ADM_DESC_ALIGN;
> +
> +	async_desc->cpl = dma_alloc_writecombine(adev->dev, async_desc->dma_len,
> +				&async_desc->dma_addr, GFP_NOWAIT);
> +
> +	if (!async_desc->cpl) {
> +		kfree(async_desc);
> +		return ERR_PTR(-ENOMEM);
> +	}
> +
> +	async_desc->adev = adev;
> +
> +	/* both command list entry and descriptors must be 8 byte aligned */
> +	cple = PTR_ALIGN(async_desc->cpl, ADM_DESC_ALIGN);
> +	desc = PTR_ALIGN(cple + 1, ADM_DESC_ALIGN);
> +	last_cmd = desc;
> +
> +	/* init cmd list */
> +	*cple = CPLE_LP;
> +	*cple |= (desc - async_desc->cpl + async_desc->dma_addr) >> 3;
> +
> +	for_each_sg(sgl, sg, sg_len, i) {
> +		unsigned int xfer_len, row_len, rows;
> +		unsigned int remainder = sg_dma_len(sg);
> +		unsigned int offset = 0;
> +
> +		do {
> +			/* use single if length is not multiple of burst */
> +			if (remainder % burst) {
> +				single_desc = desc + desc_offset;
> +				last_cmd = &single_desc->cmd;
> +				single_desc->cmd = CMD_TYPE_SINGLE;
> +				xfer_len = (remainder > ADM_MAX_XFER) ?
> +					ADM_MAX_XFER : remainder;
> +				if (direction == DMA_DEV_TO_MEM) {
> +					single_desc->dst_addr =
> +						sg_dma_address(sg) + offset;
> +					single_desc->src_addr =
> +						achan->slave.src_addr;
> +					single_desc->len = xfer_len;
> +					single_desc->cmd |= CMD_SRC_CRCI(crci);
> +				} else {
> +					single_desc->src_addr =
> +						sg_dma_address(sg) + offset;
> +					single_desc->dst_addr =
> +						achan->slave.dst_addr;
> +					single_desc->len = xfer_len;
> +					single_desc->cmd |= CMD_DST_CRCI(crci);
> +				}
> +
> +				remainder -= xfer_len;
> +				async_desc->length += xfer_len;
> +				offset += xfer_len;
> +				desc_offset += sizeof(*single_desc);
> +			} else {
> +				box_desc = desc + desc_offset;
> +				last_cmd = &box_desc->cmd;
> +				box_desc->cmd = CMD_TYPE_BOX;
> +				box_desc->row_offset = 0;
> +
> +				if (direction == DMA_DEV_TO_MEM) {
> +					box_desc->dst_addr =
> +						sg_dma_address(sg) + offset;
> +					box_desc->src_addr =
> +						achan->slave.src_addr;
> +					box_desc->cmd |= CMD_SRC_CRCI(crci);
> +					box_desc->row_offset = burst;
> +
> +				} else {
> +					box_desc->src_addr =
> +						sg_dma_address(sg) + offset;
> +					box_desc->dst_addr =
> +						achan->slave.dst_addr;
> +					box_desc->cmd |= CMD_DST_CRCI(crci);
> +					box_desc->row_offset = burst << 16;
> +				}
till this both look quite similar, also you are way deeply nested. I would
split this up to make it look better as well try reusing common parts for
both here

> +static int adm_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
> +	unsigned long arg)
> +{
this is removed, so you need to rebase this

Thanks
Andy Gross March 13, 2015, 10:06 p.m. UTC | #2
On Fri, Mar 13, 2015 at 02:27:45PM +0530, Vinod Koul wrote:
> On Wed, Feb 11, 2015 at 11:46:05PM -0600, Andy Gross wrote:
> > +++ b/drivers/dma/qcom_adm.c
> > @@ -0,0 +1,901 @@
> > +/*
> > + * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
> shouldn't this be 15 :)

yeah, need to update.

> 
>  +/* ADM registers - calculated from channel number and security domain */
> > +#define HI_CH_CMD_PTR(chan, ee)		(4*chan + 0x20800*ee)
> > +#define HI_CH_RSLT(chan, ee)		(0x40 + 4*chan + 0x20800*ee)
> > +#define HI_CH_FLUSH_STATE0(chan, ee)	(0x80 + 4*chan + 0x20800*ee)
> > +#define HI_CH_FLUSH_STATE1(chan, ee)	(0xc0 + 4*chan + 0x20800*ee)
> > +#define HI_CH_FLUSH_STATE2(chan, ee)	(0x100 + 4*chan + 0x20800*ee)
> > +#define HI_CH_FLUSH_STATE3(chan, ee)	(0x140 + 4*chan + 0x20800*ee)
> > +#define HI_CH_FLUSH_STATE4(chan, ee)	(0x180 + 4*chan + 0x20800*ee)
> > +#define HI_CH_FLUSH_STATE5(chan, ee)	(0x1c0 + 4*chan + 0x20800*ee)
> > +#define HI_CH_STATUS_SD(chan, ee)	(0x200 + 4*chan + 0x20800*ee)
> > +#define HI_CH_CONF(chan)		(0x240 + 4*chan)
> > +#define HI_CH_RSLT_CONF(chan, ee)	(0x300 + 4*chan + 0x20800*ee)
> > +#define HI_SEC_DOMAIN_IRQ_STATUS(ee)	(0x380 + 0x20800*ee)
> > +#define HI_CI_CONF(ci)			(0x390 + 4*ci)
> > +#define HI_CRCI_CONF0			0x3d0
> > +#define HI_CRCI_CONF1			0x3d4
> > +#define HI_GP_CTL			0x3d8
> > +#define HI_CRCI_CTL(crci, ee)		(0x400 + 0x4*crci + 0x20800*ee)
> two things, one the names are quite generic and may cause conflicts so pls
> fix that. Second the values, what is the deal with 4*chan, should that be a
> define as well. Also rather than copy pasting a macros would be better for
> this expansion

Yeah there are sets of registers that have both channel and execution
environment offsets.  It is messy.  I'll try to make it more sane.

> 
> > +
> > +/* channel status */
> > +#define CH_STATUS_VALID	BIT(1)
> > +
> > +/* channel result */
> > +#define CH_RSLT_VALID	BIT(31)
> > +#define CH_RSLT_ERR	BIT(3)
> > +#define CH_RSLT_FLUSH	BIT(2)
> > +#define CH_RSLT_TPD	BIT(1)
> > +
> > +/* channel conf */
> > +#define CH_CONF_MPU_DISABLE	BIT(11)
> > +#define CH_CONF_PERM_MPU_CONF	BIT(9)
> > +#define CH_CONF_FLUSH_RSLT_EN	BIT(8)
> > +#define CH_CONF_FORCE_RSLT_EN	BIT(7)
> > +#define CH_CONF_IRQ_EN		BIT(6)
> > +
> > +/* channel result conf */
> > +#define CH_RSLT_CONF_FLUSH_EN	BIT(1)
> > +#define CH_RSLT_CONF_IRQ_EN	BIT(0)
> > +
> > +/* CRCI CTL */
> > +#define CRCI_CTL_MUX_SEL	BIT(18)
> > +#define CRCI_CTL_RST		BIT(17)
> > +
> > +/* CI configuration */
> > +#define CI_RANGE_END(x)		(x << 24)
> > +#define CI_RANGE_START(x)	(x << 16)
> > +#define CI_BURST_4_WORDS	0x4
> > +#define CI_BURST_8_WORDS	0x8
> shouldn't you be consistent is usage of BIT()

good catch

> > +
> > +/* GP CTL */
> > +#define GP_CTL_LP_EN		BIT(12)
> > +#define GP_CTL_LP_CNT(x)	(x << 8)
> > +
> > +/* Command pointer list entry */
> > +#define CPLE_LP			BIT(31)
> > +#define CPLE_CMD_PTR_LIST	BIT(29)
> > +
> > +/* Command list entry */
> > +#define CMD_LC			BIT(31)
> > +#define CMD_DST_CRCI(n)		(((n) & 0xf) << 7)
> > +#define CMD_SRC_CRCI(n)		(((n) & 0xf) << 3)
> > +
> > +#define CMD_TYPE_SINGLE		0x0
> > +#define CMD_TYPE_BOX		0x3a
> naming issues...

ok. will try to come up with something better

> > +static int adm_alloc_chan(struct dma_chan *chan)
> > +{
> > +	return 0;
> > +}
> This is no longer mandatory, so can be dropped

will remove

> 
> > +static int adm_get_blksize(unsigned int burst)
> > +{
> > +	int ret;
> > +
> > +	switch (burst) {
> > +	case 16:
> > +		ret = 0;
> > +		break;
> > +	case 32:
> > +		ret = 1;
> > +		break;
> > +	case 64:
> > +		ret = 2;
> > +		break;
> > +	case 128:
> > +		ret = 3;
> > +		break;
> > +	case 192:
> > +		ret = 4;
> > +		break;
> > +	case 256:
> > +		ret = 5;
> > +		break;
> ffs(burst>>4) ?

that should work nicely.  thanks.

> > +static struct dma_async_tx_descriptor *adm_prep_slave_sg(struct dma_chan *chan,
> > +	struct scatterlist *sgl, unsigned int sg_len,
> > +	enum dma_transfer_direction direction, unsigned long flags,
> > +	void *context)
> > +{
> > +	struct adm_chan *achan = to_adm_chan(chan);
> > +	struct adm_device *adev = achan->adev;
> > +	struct adm_async_desc *async_desc;
> > +	struct scatterlist *sg;
> > +	u32 i;
> > +	u32 single_count = 0, box_count = 0, desc_offset = 0, crci = 0;
> > +	struct adm_desc_hw_box *box_desc;
> > +	struct adm_desc_hw_single *single_desc;
> > +	void *desc;
> > +	u32 *cple, *last_cmd;
> > +	u32 burst;
> > +	int blk_size = 0;
> > +
> > +
> > +	if (!is_slave_direction(direction)) {
> > +		dev_err(adev->dev, "invalid dma direction\n");
> > +		return NULL;
> > +	}
> > +
> > +	/*
> > +	 * get burst value from slave configuration
> > +	 * If zero, default to maximum burst size
> > +	 * If larger than the max transfer size, set to ADM_MAX_XFER
> > +	 */
> > +	burst = (direction == DMA_MEM_TO_DEV) ?
> > +		achan->slave.dst_maxburst :
> > +		achan->slave.src_maxburst;
> > +
> > +	if (!burst || burst > ADM_MAX_XFER)
> > +		burst = ADM_MAX_XFER;
> For slave, we should send error here. The DMA settings are matched with
> slave FIFO, so any change here can cause issues

ok.  I was trying to unify the flow control use case with the non flow control
use case.  the slave config burst is only used in the case of flow control.

> 
> > +
> > +	/* if using flow control, validate burst and crci values */
> > +	if (achan->slave.device_fc) {
> > +
> > +		blk_size = adm_get_blksize(burst);
> > +		if (blk_size < 0) {
> > +			dev_err(adev->dev, "invalid burst value w/ crci: %d\n",
> > +				burst);
> > +			return ERR_PTR(-EINVAL);
> > +		}
> > +
> > +		crci = achan->slave.slave_id & 0xf;
> > +		if (!crci || achan->slave.slave_id > 0x1f) {
> > +			dev_err(adev->dev, "invalid crci value\n");
> > +			return ERR_PTR(-EINVAL);
> > +		}
> > +	}
> > +
> > +	/* iterate through sgs and compute allocation size of structures */
> > +	for_each_sg(sgl, sg, sg_len, i)
> > +		if (sg_dma_len(sg) % burst)

i used it here to bust up the dma buffer into burstable chunks

> > +			single_count += DIV_ROUND_UP(sg_dma_len(sg), burst);
> > +		else
> > +			box_count += DIV_ROUND_UP(sg_dma_len(sg) / burst,
> > +							ADM_MAX_ROWS);
> > +

<snip>

> > +			} else {
> > +				box_desc = desc + desc_offset;
> > +				last_cmd = &box_desc->cmd;
> > +				box_desc->cmd = CMD_TYPE_BOX;
> > +				box_desc->row_offset = 0;
> > +
> > +				if (direction == DMA_DEV_TO_MEM) {
> > +					box_desc->dst_addr =
> > +						sg_dma_address(sg) + offset;
> > +					box_desc->src_addr =
> > +						achan->slave.src_addr;
> > +					box_desc->cmd |= CMD_SRC_CRCI(crci);
> > +					box_desc->row_offset = burst;
> > +
> > +				} else {
> > +					box_desc->src_addr =
> > +						sg_dma_address(sg) + offset;
> > +					box_desc->dst_addr =
> > +						achan->slave.dst_addr;
> > +					box_desc->cmd |= CMD_DST_CRCI(crci);
> > +					box_desc->row_offset = burst << 16;
> > +				}
> till this both look quite similar, also you are way deeply nested. I would
> split this up to make it look better as well try reusing common parts for
> both here

Ok.  I'll rework this.

> 
> > +static int adm_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
> > +	unsigned long arg)
> > +{
> this is removed, so you need to rebase this

Will do.
Sricharan Ramabadhran March 16, 2015, 8:15 a.m. UTC | #3
Hi,

<snip>
>
>>
>> > +static int adm_get_blksize(unsigned int burst)
>> > +{
>> > +	int ret;
>> > +
>> > +	switch (burst) {
>> > +	case 16:
>> > +		ret = 0;
>> > +		break;
>> > +	case 32:
>> > +		ret = 1;
>> > +		break;
>> > +	case 64:
>> > +		ret = 2;
>> > +		break;
>> > +	case 128:
>> > +		ret = 3;
>> > +		break;
>> > +	case 192:
>> > +		ret = 4;
>> > +		break;
>> > +	case 256:
>> > +		ret = 5;
>> > +		break;
>> ffs(burst>>4) ?
>
> that should work nicely.  thanks.
>
  Will not work for 192, 256 ?

Regards,
 Sricharan

--
To unsubscribe from this list: send the line "unsubscribe dmaengine" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Andy Gross March 17, 2015, 5:04 a.m. UTC | #4
On Mon, Mar 16, 2015 at 08:15:26AM -0000, sricharan@codeaurora.org wrote:
> Hi,
> 
> <snip>
> >
> >>
> >> > +static int adm_get_blksize(unsigned int burst)
> >> > +{
> >> > +	int ret;
> >> > +
> >> > +	switch (burst) {
> >> > +	case 16:
> >> > +		ret = 0;
> >> > +		break;
> >> > +	case 32:
> >> > +		ret = 1;
> >> > +		break;
> >> > +	case 64:
> >> > +		ret = 2;
> >> > +		break;
> >> > +	case 128:
> >> > +		ret = 3;
> >> > +		break;
> >> > +	case 192:
> >> > +		ret = 4;
> >> > +		break;
> >> > +	case 256:
> >> > +		ret = 5;
> >> > +		break;
> >> ffs(burst>>4) ?
> >
> > that should work nicely.  thanks.
> >
>   Will not work for 192, 256 ?

you are right.  I'll have to separate those out into 2 more cases.  Good catch!
diff mbox

Patch

diff --git a/drivers/dma/Kconfig b/drivers/dma/Kconfig
index f2b2c4e..69bc15e 100644
--- a/drivers/dma/Kconfig
+++ b/drivers/dma/Kconfig
@@ -464,4 +464,14 @@  config QCOM_BAM_DMA
 	  Enable support for the QCOM BAM DMA controller.  This controller
 	  provides DMA capabilities for a variety of on-chip devices.
 
+config QCOM_ADM
+	tristate "Qualcomm ADM support"
+	depends on ARCH_QCOM || (COMPILE_TEST && OF && ARM)
+	select DMA_ENGINE
+	select DMA_VIRTUAL_CHANNELS
+	---help---
+	  Enable support for the Qualcomm ADM DMA controller.  This controller
+	  provides DMA capabilities for both general purpose and on-chip
+	  peripheral devices.
+
 endif
diff --git a/drivers/dma/Makefile b/drivers/dma/Makefile
index 2022b54..3b7ead6 100644
--- a/drivers/dma/Makefile
+++ b/drivers/dma/Makefile
@@ -50,3 +50,4 @@  obj-y += xilinx/
 obj-$(CONFIG_INTEL_MIC_X100_DMA) += mic_x100_dma.o
 obj-$(CONFIG_NBPFAXI_DMA) += nbpfaxi.o
 obj-$(CONFIG_DMA_SUN6I) += sun6i-dma.o
+obj-$(CONFIG_QCOM_ADM) += qcom_adm.o
diff --git a/drivers/dma/qcom_adm.c b/drivers/dma/qcom_adm.c
new file mode 100644
index 0000000..baea945
--- /dev/null
+++ b/drivers/dma/qcom_adm.c
@@ -0,0 +1,901 @@ 
+/*
+ * Copyright (c) 2013-2014, The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/init.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/dma-mapping.h>
+#include <linux/scatterlist.h>
+#include <linux/device.h>
+#include <linux/platform_device.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/of_dma.h>
+#include <linux/reset.h>
+#include <linux/clk.h>
+#include <linux/dmaengine.h>
+
+#include "dmaengine.h"
+#include "virt-dma.h"
+
+/* ADM registers - calculated from channel number and security domain */
+#define HI_CH_CMD_PTR(chan, ee)		(4*chan + 0x20800*ee)
+#define HI_CH_RSLT(chan, ee)		(0x40 + 4*chan + 0x20800*ee)
+#define HI_CH_FLUSH_STATE0(chan, ee)	(0x80 + 4*chan + 0x20800*ee)
+#define HI_CH_FLUSH_STATE1(chan, ee)	(0xc0 + 4*chan + 0x20800*ee)
+#define HI_CH_FLUSH_STATE2(chan, ee)	(0x100 + 4*chan + 0x20800*ee)
+#define HI_CH_FLUSH_STATE3(chan, ee)	(0x140 + 4*chan + 0x20800*ee)
+#define HI_CH_FLUSH_STATE4(chan, ee)	(0x180 + 4*chan + 0x20800*ee)
+#define HI_CH_FLUSH_STATE5(chan, ee)	(0x1c0 + 4*chan + 0x20800*ee)
+#define HI_CH_STATUS_SD(chan, ee)	(0x200 + 4*chan + 0x20800*ee)
+#define HI_CH_CONF(chan)		(0x240 + 4*chan)
+#define HI_CH_RSLT_CONF(chan, ee)	(0x300 + 4*chan + 0x20800*ee)
+#define HI_SEC_DOMAIN_IRQ_STATUS(ee)	(0x380 + 0x20800*ee)
+#define HI_CI_CONF(ci)			(0x390 + 4*ci)
+#define HI_CRCI_CONF0			0x3d0
+#define HI_CRCI_CONF1			0x3d4
+#define HI_GP_CTL			0x3d8
+#define HI_CRCI_CTL(crci, ee)		(0x400 + 0x4*crci + 0x20800*ee)
+
+/* channel status */
+#define CH_STATUS_VALID	BIT(1)
+
+/* channel result */
+#define CH_RSLT_VALID	BIT(31)
+#define CH_RSLT_ERR	BIT(3)
+#define CH_RSLT_FLUSH	BIT(2)
+#define CH_RSLT_TPD	BIT(1)
+
+/* channel conf */
+#define CH_CONF_MPU_DISABLE	BIT(11)
+#define CH_CONF_PERM_MPU_CONF	BIT(9)
+#define CH_CONF_FLUSH_RSLT_EN	BIT(8)
+#define CH_CONF_FORCE_RSLT_EN	BIT(7)
+#define CH_CONF_IRQ_EN		BIT(6)
+
+/* channel result conf */
+#define CH_RSLT_CONF_FLUSH_EN	BIT(1)
+#define CH_RSLT_CONF_IRQ_EN	BIT(0)
+
+/* CRCI CTL */
+#define CRCI_CTL_MUX_SEL	BIT(18)
+#define CRCI_CTL_RST		BIT(17)
+
+/* CI configuration */
+#define CI_RANGE_END(x)		(x << 24)
+#define CI_RANGE_START(x)	(x << 16)
+#define CI_BURST_4_WORDS	0x4
+#define CI_BURST_8_WORDS	0x8
+
+/* GP CTL */
+#define GP_CTL_LP_EN		BIT(12)
+#define GP_CTL_LP_CNT(x)	(x << 8)
+
+/* Command pointer list entry */
+#define CPLE_LP			BIT(31)
+#define CPLE_CMD_PTR_LIST	BIT(29)
+
+/* Command list entry */
+#define CMD_LC			BIT(31)
+#define CMD_DST_CRCI(n)		(((n) & 0xf) << 7)
+#define CMD_SRC_CRCI(n)		(((n) & 0xf) << 3)
+
+#define CMD_TYPE_SINGLE		0x0
+#define CMD_TYPE_BOX		0x3
+
+#define ADM_DESC_ALIGN	8
+#define ADM_MAX_XFER	(SZ_64K-1)
+#define ADM_MAX_ROWS	(SZ_64K-1)
+#define ADM_MAX_CHANNELS	16
+
+struct adm_desc_hw_box {
+	u32 cmd;
+	u32 src_addr;
+	u32 dst_addr;
+	u32 row_len;
+	u32 num_rows;
+	u32 row_offset;
+};
+
+struct adm_desc_hw_single {
+	u32 cmd;
+	u32 src_addr;
+	u32 dst_addr;
+	u32 len;
+};
+
+struct adm_async_desc {
+	struct virt_dma_desc vd;
+	struct adm_device *adev;
+
+	size_t length;
+	enum dma_transfer_direction dir;
+	dma_addr_t dma_addr;
+	size_t dma_len;
+
+	void *cpl;
+	dma_addr_t cp_addr;
+	u32 crci;
+	u32 mux;
+	u32 blk_size;
+};
+
+struct adm_chan {
+	struct virt_dma_chan vc;
+	struct adm_device *adev;
+
+	/* parsed from DT */
+	u32 id;			/* channel id */
+
+	struct adm_async_desc *curr_txd;
+	struct dma_slave_config slave;
+	struct list_head node;
+
+	int error;
+	int initialized;
+};
+
+static inline struct adm_chan *to_adm_chan(struct dma_chan *common)
+{
+	return container_of(common, struct adm_chan, vc.chan);
+}
+
+struct adm_device {
+	void __iomem *regs;
+	struct device *dev;
+	struct dma_device common;
+	struct device_dma_parameters dma_parms;
+	struct adm_chan *channels;
+
+	u32 ee;
+
+	struct clk *core_clk;
+	struct clk *iface_clk;
+
+	struct reset_control *clk_reset;
+	struct reset_control *c0_reset;
+	struct reset_control *c1_reset;
+	struct reset_control *c2_reset;
+	int irq;
+};
+
+/**
+ * adm_alloc_chan - Allocates channel resources for DMA channel
+ *
+ * This function is effectively a stub, as we don't need to setup any resources
+ */
+static int adm_alloc_chan(struct dma_chan *chan)
+{
+	return 0;
+}
+
+/**
+ * adm_free_chan - Frees dma resources associated with the specific channel
+ *
+ * Free all allocated descriptors associated with this channel
+ *
+ */
+static void adm_free_chan(struct dma_chan *chan)
+{
+	/* free all queued descriptors */
+	vchan_free_chan_resources(to_virt_chan(chan));
+}
+
+/**
+ * adm_get_blksize - Get block size from burst value
+ *
+ */
+static int adm_get_blksize(unsigned int burst)
+{
+	int ret;
+
+	switch (burst) {
+	case 16:
+		ret = 0;
+		break;
+	case 32:
+		ret = 1;
+		break;
+	case 64:
+		ret = 2;
+		break;
+	case 128:
+		ret = 3;
+		break;
+	case 192:
+		ret = 4;
+		break;
+	case 256:
+		ret = 5;
+		break;
+	default:
+		ret = -EINVAL;
+		break;
+	}
+
+	return ret;
+}
+
+/**
+ * adm_prep_slave_sg - Prep slave sg transaction
+ *
+ * @chan: dma channel
+ * @sgl: scatter gather list
+ * @sg_len: length of sg
+ * @direction: DMA transfer direction
+ * @flags: DMA flags
+ * @context: transfer context (unused)
+ */
+static struct dma_async_tx_descriptor *adm_prep_slave_sg(struct dma_chan *chan,
+	struct scatterlist *sgl, unsigned int sg_len,
+	enum dma_transfer_direction direction, unsigned long flags,
+	void *context)
+{
+	struct adm_chan *achan = to_adm_chan(chan);
+	struct adm_device *adev = achan->adev;
+	struct adm_async_desc *async_desc;
+	struct scatterlist *sg;
+	u32 i;
+	u32 single_count = 0, box_count = 0, desc_offset = 0, crci = 0;
+	struct adm_desc_hw_box *box_desc;
+	struct adm_desc_hw_single *single_desc;
+	void *desc;
+	u32 *cple, *last_cmd;
+	u32 burst;
+	int blk_size = 0;
+
+
+	if (!is_slave_direction(direction)) {
+		dev_err(adev->dev, "invalid dma direction\n");
+		return NULL;
+	}
+
+	/*
+	 * get burst value from slave configuration
+	 * If zero, default to maximum burst size
+	 * If larger than the max transfer size, set to ADM_MAX_XFER
+	 */
+	burst = (direction == DMA_MEM_TO_DEV) ?
+		achan->slave.dst_maxburst :
+		achan->slave.src_maxburst;
+
+	if (!burst || burst > ADM_MAX_XFER)
+		burst = ADM_MAX_XFER;
+
+	/* if using flow control, validate burst and crci values */
+	if (achan->slave.device_fc) {
+
+		blk_size = adm_get_blksize(burst);
+		if (blk_size < 0) {
+			dev_err(adev->dev, "invalid burst value w/ crci: %d\n",
+				burst);
+			return ERR_PTR(-EINVAL);
+		}
+
+		crci = achan->slave.slave_id & 0xf;
+		if (!crci || achan->slave.slave_id > 0x1f) {
+			dev_err(adev->dev, "invalid crci value\n");
+			return ERR_PTR(-EINVAL);
+		}
+	}
+
+	/* iterate through sgs and compute allocation size of structures */
+	for_each_sg(sgl, sg, sg_len, i)
+		if (sg_dma_len(sg) % burst)
+			single_count += DIV_ROUND_UP(sg_dma_len(sg), burst);
+		else
+			box_count += DIV_ROUND_UP(sg_dma_len(sg) / burst,
+							ADM_MAX_ROWS);
+
+	async_desc = kzalloc(sizeof(*async_desc), GFP_NOWAIT);
+	if (!async_desc)
+		return ERR_PTR(-ENOMEM);
+
+	if (crci)
+		async_desc->mux = achan->slave.slave_id >> 4 ?
+					CRCI_CTL_MUX_SEL : 0;
+	async_desc->crci = crci;
+	async_desc->blk_size = blk_size;
+	async_desc->dma_len = single_count * sizeof(*single_desc) +
+				box_count * sizeof(*box_desc) + sizeof(*cple) +
+				2*ADM_DESC_ALIGN;
+
+	async_desc->cpl = dma_alloc_writecombine(adev->dev, async_desc->dma_len,
+				&async_desc->dma_addr, GFP_NOWAIT);
+
+	if (!async_desc->cpl) {
+		kfree(async_desc);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	async_desc->adev = adev;
+
+	/* both command list entry and descriptors must be 8 byte aligned */
+	cple = PTR_ALIGN(async_desc->cpl, ADM_DESC_ALIGN);
+	desc = PTR_ALIGN(cple + 1, ADM_DESC_ALIGN);
+	last_cmd = desc;
+
+	/* init cmd list */
+	*cple = CPLE_LP;
+	*cple |= (desc - async_desc->cpl + async_desc->dma_addr) >> 3;
+
+	for_each_sg(sgl, sg, sg_len, i) {
+		unsigned int xfer_len, row_len, rows;
+		unsigned int remainder = sg_dma_len(sg);
+		unsigned int offset = 0;
+
+		do {
+			/* use single if length is not multiple of burst */
+			if (remainder % burst) {
+				single_desc = desc + desc_offset;
+				last_cmd = &single_desc->cmd;
+				single_desc->cmd = CMD_TYPE_SINGLE;
+				xfer_len = (remainder > ADM_MAX_XFER) ?
+					ADM_MAX_XFER : remainder;
+				if (direction == DMA_DEV_TO_MEM) {
+					single_desc->dst_addr =
+						sg_dma_address(sg) + offset;
+					single_desc->src_addr =
+						achan->slave.src_addr;
+					single_desc->len = xfer_len;
+					single_desc->cmd |= CMD_SRC_CRCI(crci);
+				} else {
+					single_desc->src_addr =
+						sg_dma_address(sg) + offset;
+					single_desc->dst_addr =
+						achan->slave.dst_addr;
+					single_desc->len = xfer_len;
+					single_desc->cmd |= CMD_DST_CRCI(crci);
+				}
+
+				remainder -= xfer_len;
+				async_desc->length += xfer_len;
+				offset += xfer_len;
+				desc_offset += sizeof(*single_desc);
+			} else {
+				box_desc = desc + desc_offset;
+				last_cmd = &box_desc->cmd;
+				box_desc->cmd = CMD_TYPE_BOX;
+				box_desc->row_offset = 0;
+
+				if (direction == DMA_DEV_TO_MEM) {
+					box_desc->dst_addr =
+						sg_dma_address(sg) + offset;
+					box_desc->src_addr =
+						achan->slave.src_addr;
+					box_desc->cmd |= CMD_SRC_CRCI(crci);
+					box_desc->row_offset = burst;
+
+				} else {
+					box_desc->src_addr =
+						sg_dma_address(sg) + offset;
+					box_desc->dst_addr =
+						achan->slave.dst_addr;
+					box_desc->cmd |= CMD_DST_CRCI(crci);
+					box_desc->row_offset = burst << 16;
+				}
+
+				desc_offset += sizeof(*box_desc);
+				rows = remainder / burst;
+				rows = min_t(u32, rows, ADM_MAX_ROWS);
+				row_len = burst;
+				box_desc->num_rows = rows << 16 | rows;
+				box_desc->row_len = row_len << 16 | row_len;
+
+				remainder -= row_len * rows;
+				async_desc->length += row_len * rows;
+				offset += row_len * rows;
+			}
+		} while (remainder > 0);
+	}
+
+	/* set last command flag */
+	*last_cmd |= CMD_LC;
+
+	return vchan_tx_prep(&achan->vc, &async_desc->vd, flags);
+}
+
+/**
+ * adm_terminate_all - terminate all transactions on a channel
+ * @achan: adm dma channel
+ *
+ * Dequeues and frees all transactions, aborts current transaction
+ * No callbacks are done
+ *
+ */
+static void adm_terminate_all(struct adm_chan *achan)
+{
+	struct adm_device *adev = achan->adev;
+	unsigned long flags;
+	LIST_HEAD(head);
+
+	/* send flush command to terminate current transaction */
+	writel_relaxed(0x0,
+		adev->regs + HI_CH_FLUSH_STATE0(achan->id, adev->ee));
+
+	spin_lock_irqsave(&achan->vc.lock, flags);
+	vchan_get_all_descriptors(&achan->vc, &head);
+	spin_unlock_irqrestore(&achan->vc.lock, flags);
+
+	vchan_dma_desc_free_list(&achan->vc, &head);
+}
+
+/**
+ * adm_control - DMA device control
+ * @chan: dma channel
+ * @cmd: control cmd
+ * @arg: cmd argument
+ *
+ * Perform DMA control command
+ *
+ */
+static int adm_control(struct dma_chan *chan, enum dma_ctrl_cmd cmd,
+	unsigned long arg)
+{
+	struct adm_chan *achan = to_adm_chan(chan);
+	unsigned long flag;
+	int ret = 0;
+
+	switch (cmd) {
+	case DMA_SLAVE_CONFIG:
+		spin_lock_irqsave(&achan->vc.lock, flag);
+		memcpy(&achan->slave, (void *)arg,
+			sizeof(struct dma_slave_config));
+		spin_unlock_irqrestore(&achan->vc.lock, flag);
+		break;
+
+	case DMA_TERMINATE_ALL:
+		adm_terminate_all(achan);
+		break;
+
+	default:
+		ret = -ENXIO;
+		break;
+	};
+
+	return ret;
+}
+
+/**
+ * adm_start_dma - start next transaction
+ * @achan - ADM dma channel
+ */
+static void adm_start_dma(struct adm_chan *achan)
+{
+	struct virt_dma_desc *vd = vchan_next_desc(&achan->vc);
+	struct adm_device *adev = achan->adev;
+	struct adm_async_desc *async_desc;
+
+	lockdep_assert_held(&achan->vc.lock);
+
+	if (!vd)
+		return;
+
+	list_del(&vd->node);
+
+	/* write next command list out to the CMD FIFO */
+	async_desc = container_of(vd, struct adm_async_desc, vd);
+	achan->curr_txd = async_desc;
+
+	/* reset channel error */
+	achan->error = 0;
+
+	if (!achan->initialized) {
+		/* enable interrupts */
+		writel(CH_CONF_IRQ_EN | CH_CONF_FLUSH_RSLT_EN |
+			CH_CONF_FORCE_RSLT_EN | CH_CONF_PERM_MPU_CONF |
+			CH_CONF_MPU_DISABLE,
+			adev->regs + HI_CH_CONF(achan->id));
+
+		writel(CH_RSLT_CONF_IRQ_EN | CH_RSLT_CONF_FLUSH_EN,
+			adev->regs + HI_CH_RSLT_CONF(achan->id, adev->ee));
+
+		achan->initialized = 1;
+	}
+
+	/* set the crci block size if this transaction requires CRCI */
+	if (async_desc->crci) {
+		writel(async_desc->mux | async_desc->blk_size,
+			adev->regs + HI_CRCI_CTL(async_desc->crci, adev->ee));
+	}
+
+	/* make sure IRQ enable doesn't get reordered */
+	wmb();
+
+	/* write next command list out to the CMD FIFO */
+	writel(ALIGN(async_desc->dma_addr, ADM_DESC_ALIGN) >> 3,
+		adev->regs + HI_CH_CMD_PTR(achan->id, adev->ee));
+}
+
+/**
+ * adm_dma_irq - irq handler for ADM controller
+ * @irq: IRQ of interrupt
+ * @data: callback data
+ *
+ * IRQ handler for the bam controller
+ */
+static irqreturn_t adm_dma_irq(int irq, void *data)
+{
+	struct adm_device *adev = data;
+	u32 srcs, i;
+	struct adm_async_desc *async_desc;
+	unsigned long flags;
+
+	srcs = readl_relaxed(adev->regs +
+			HI_SEC_DOMAIN_IRQ_STATUS(adev->ee));
+
+	for (i = 0; i < ADM_MAX_CHANNELS; i++) {
+		struct adm_chan *achan = &adev->channels[i];
+		u32 status, result;
+
+		if (srcs & BIT(i)) {
+			status = readl_relaxed(adev->regs +
+				HI_CH_STATUS_SD(i, adev->ee));
+
+			/* if no result present, skip */
+			if (!(status & CH_STATUS_VALID))
+				continue;
+
+			result = readl_relaxed(adev->regs +
+				HI_CH_RSLT(i, adev->ee));
+
+			/* no valid results, skip */
+			if (!(result & CH_RSLT_VALID))
+				continue;
+
+			/* flag error if transaction was flushed or failed */
+			if (result & (CH_RSLT_ERR | CH_RSLT_FLUSH))
+				achan->error = 1;
+
+			spin_lock_irqsave(&achan->vc.lock, flags);
+			async_desc = achan->curr_txd;
+
+			achan->curr_txd = NULL;
+
+			if (async_desc) {
+				vchan_cookie_complete(&async_desc->vd);
+
+				/* kick off next DMA */
+				adm_start_dma(achan);
+			}
+
+			spin_unlock_irqrestore(&achan->vc.lock, flags);
+		}
+	}
+
+	return IRQ_HANDLED;
+}
+
+/**
+ * adm_tx_status - returns status of transaction
+ * @chan: dma channel
+ * @cookie: transaction cookie
+ * @txstate: DMA transaction state
+ *
+ * Return status of dma transaction
+ */
+static enum dma_status adm_tx_status(struct dma_chan *chan, dma_cookie_t cookie,
+	struct dma_tx_state *txstate)
+{
+	struct adm_chan *achan = to_adm_chan(chan);
+	struct virt_dma_desc *vd;
+	enum dma_status ret;
+	unsigned long flags;
+	size_t residue = 0;
+
+	ret = dma_cookie_status(chan, cookie, txstate);
+	if (ret == DMA_COMPLETE || !txstate)
+		return ret;
+
+	spin_lock_irqsave(&achan->vc.lock, flags);
+
+	vd = vchan_find_desc(&achan->vc, cookie);
+	if (vd)
+		residue = container_of(vd, struct adm_async_desc, vd)->length;
+
+	spin_unlock_irqrestore(&achan->vc.lock, flags);
+
+	/*
+	 * residue is either the full length if it is in the issued list, or 0
+	 * if it is in progress.  We have no reliable way of determining
+	 * anything inbetween
+	*/
+	dma_set_residue(txstate, residue);
+
+	if (achan->error)
+		return DMA_ERROR;
+
+	return ret;
+}
+
+static struct dma_chan *adm_dma_xlate(struct of_phandle_args *dma_spec,
+	struct of_dma *of)
+{
+	struct adm_device *adev = container_of(of->of_dma_data,
+			struct adm_device, common);
+	struct dma_chan *chan;
+	unsigned int request;
+
+	if (dma_spec->args_count != 1) {
+		dev_err(adev->dev, "incorrect number of dma arguments\n");
+		return NULL;
+	}
+
+	request = dma_spec->args[0];
+	if (request >= ADM_MAX_CHANNELS)
+		return NULL;
+
+	chan = dma_get_slave_channel(&(adev->channels[request].vc.chan));
+
+	if (!chan)
+		return NULL;
+
+	return chan;
+}
+
+/**
+ * adm_issue_pending - starts pending transactions
+ * @chan: dma channel
+ *
+ * Issues all pending transactions and starts DMA
+ */
+static void adm_issue_pending(struct dma_chan *chan)
+{
+	struct adm_chan *achan = to_adm_chan(chan);
+	unsigned long flags;
+
+	spin_lock_irqsave(&achan->vc.lock, flags);
+
+	if (vchan_issue_pending(&achan->vc) && !achan->curr_txd)
+		adm_start_dma(achan);
+	spin_unlock_irqrestore(&achan->vc.lock, flags);
+}
+
+/**
+ * adm_dma_free_desc - free descriptor memory
+ * @vd: virtual descriptor
+ *
+ */
+static void adm_dma_free_desc(struct virt_dma_desc *vd)
+{
+	struct adm_async_desc *async_desc = container_of(vd,
+			struct adm_async_desc, vd);
+
+	dma_free_writecombine(async_desc->adev->dev, async_desc->dma_len,
+		async_desc->cpl, async_desc->dma_addr);
+	kfree(async_desc);
+}
+
+static void adm_channel_init(struct adm_device *adev, struct adm_chan *achan,
+	u32 index)
+{
+	achan->id = index;
+	achan->adev = adev;
+
+	vchan_init(&achan->vc, &adev->common);
+	achan->vc.desc_free = adm_dma_free_desc;
+}
+
+static int adm_dma_probe(struct platform_device *pdev)
+{
+	struct adm_device *adev;
+	struct resource *iores;
+	int ret;
+	u32 i;
+
+	adev = devm_kzalloc(&pdev->dev, sizeof(*adev), GFP_KERNEL);
+	if (!adev)
+		return -ENOMEM;
+
+	adev->dev = &pdev->dev;
+
+	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	adev->regs = devm_ioremap_resource(&pdev->dev, iores);
+	if (IS_ERR(adev->regs))
+		return PTR_ERR(adev->regs);
+
+	adev->irq = platform_get_irq(pdev, 0);
+	if (adev->irq < 0)
+		return adev->irq;
+
+	ret = of_property_read_u32(pdev->dev.of_node, "qcom,ee", &adev->ee);
+	if (ret) {
+		dev_err(adev->dev, "Execution environment unspecified\n");
+		return ret;
+	}
+
+	adev->core_clk = devm_clk_get(adev->dev, "core");
+	if (IS_ERR(adev->core_clk))
+		return PTR_ERR(adev->core_clk);
+
+	ret = clk_prepare_enable(adev->core_clk);
+	if (ret) {
+		dev_err(adev->dev, "failed to prepare/enable core clock\n");
+		return ret;
+	}
+
+	adev->iface_clk = devm_clk_get(adev->dev, "iface");
+	if (IS_ERR(adev->iface_clk)) {
+		ret = PTR_ERR(adev->iface_clk);
+		goto err_disable_core_clk;
+	}
+
+	ret = clk_prepare_enable(adev->iface_clk);
+	if (ret) {
+		dev_err(adev->dev, "failed to prepare/enable iface clock\n");
+		goto err_disable_core_clk;
+	}
+
+	adev->clk_reset = devm_reset_control_get(&pdev->dev, "clk");
+	if (IS_ERR(adev->clk_reset)) {
+		dev_err(adev->dev, "failed to get ADM0 reset\n");
+		ret = PTR_ERR(adev->clk_reset);
+		goto err_disable_clks;
+	}
+
+	adev->c0_reset = devm_reset_control_get(&pdev->dev, "c0");
+	if (IS_ERR(adev->c0_reset)) {
+		dev_err(adev->dev, "failed to get ADM0 C0 reset\n");
+		ret = PTR_ERR(adev->c0_reset);
+		goto err_disable_clks;
+	}
+
+	adev->c1_reset = devm_reset_control_get(&pdev->dev, "c1");
+	if (IS_ERR(adev->c1_reset)) {
+		dev_err(adev->dev, "failed to get ADM0 C1 reset\n");
+		ret = PTR_ERR(adev->c1_reset);
+		goto err_disable_clks;
+	}
+
+	adev->c2_reset = devm_reset_control_get(&pdev->dev, "c2");
+	if (IS_ERR(adev->c2_reset)) {
+		dev_err(adev->dev, "failed to get ADM0 C2 reset\n");
+		ret = PTR_ERR(adev->c2_reset);
+		goto err_disable_clks;
+	}
+
+	reset_control_assert(adev->clk_reset);
+	reset_control_assert(adev->c0_reset);
+	reset_control_assert(adev->c1_reset);
+	reset_control_assert(adev->c2_reset);
+
+	reset_control_deassert(adev->clk_reset);
+	reset_control_deassert(adev->c0_reset);
+	reset_control_deassert(adev->c1_reset);
+	reset_control_deassert(adev->c2_reset);
+
+	adev->channels = devm_kcalloc(adev->dev, ADM_MAX_CHANNELS,
+				sizeof(*adev->channels), GFP_KERNEL);
+
+	if (!adev->channels) {
+		ret = -ENOMEM;
+		goto err_disable_clks;
+	}
+
+	/* allocate and initialize channels */
+	INIT_LIST_HEAD(&adev->common.channels);
+
+	for (i = 0; i < ADM_MAX_CHANNELS; i++)
+		adm_channel_init(adev, &adev->channels[i], i);
+
+	/* reset CRCIs */
+	for (i = 0; i < 16; i++)
+		writel(CRCI_CTL_RST, adev->regs + HI_CRCI_CTL(i, adev->ee));
+
+	/* configure client interfaces */
+	writel(CI_RANGE_START(0x40) | CI_RANGE_END(0xb0) | CI_BURST_8_WORDS,
+		adev->regs + HI_CI_CONF(0));
+	writel(CI_RANGE_START(0x2a) | CI_RANGE_END(0x2c) | CI_BURST_8_WORDS,
+		adev->regs + HI_CI_CONF(1));
+	writel(CI_RANGE_START(0x12) | CI_RANGE_END(0x28) | CI_BURST_8_WORDS,
+		adev->regs + HI_CI_CONF(2));
+	writel(GP_CTL_LP_EN | GP_CTL_LP_CNT(0xf), adev->regs + HI_GP_CTL);
+
+	ret = devm_request_irq(adev->dev, adev->irq, adm_dma_irq,
+			0, "adm_dma", adev);
+	if (ret)
+		goto err_disable_clks;
+
+	platform_set_drvdata(pdev, adev);
+
+	adev->common.dev = adev->dev;
+	adev->common.dev->dma_parms = &adev->dma_parms;
+
+	/* set capabilities */
+	dma_cap_zero(adev->common.cap_mask);
+	dma_cap_set(DMA_SLAVE, adev->common.cap_mask);
+	dma_cap_set(DMA_PRIVATE, adev->common.cap_mask);
+
+	/* initialize dmaengine apis */
+	adev->common.device_alloc_chan_resources = adm_alloc_chan;
+	adev->common.device_free_chan_resources = adm_free_chan;
+	adev->common.device_prep_slave_sg = adm_prep_slave_sg;
+	adev->common.device_control = adm_control;
+	adev->common.device_issue_pending = adm_issue_pending;
+	adev->common.device_tx_status = adm_tx_status;
+
+	ret = dma_async_device_register(&adev->common);
+	if (ret) {
+		dev_err(adev->dev, "failed to register dma async device\n");
+		goto err_disable_clks;
+	}
+
+	ret = of_dma_controller_register(pdev->dev.of_node, adm_dma_xlate,
+					&adev->common);
+	if (ret)
+		goto err_unregister_dma;
+
+	return 0;
+
+err_unregister_dma:
+	dma_async_device_unregister(&adev->common);
+err_disable_clks:
+	clk_disable_unprepare(adev->iface_clk);
+err_disable_core_clk:
+	clk_disable_unprepare(adev->core_clk);
+
+	return ret;
+}
+
+static int adm_dma_remove(struct platform_device *pdev)
+{
+	struct adm_device *adev = platform_get_drvdata(pdev);
+	struct adm_chan *achan;
+	u32 i;
+
+	of_dma_controller_free(pdev->dev.of_node);
+	dma_async_device_unregister(&adev->common);
+
+	devm_free_irq(adev->dev, adev->irq, adev);
+
+	for (i = 0; i < ADM_MAX_CHANNELS; i++) {
+		achan = &adev->channels[i];
+		writel(CH_CONF_FLUSH_RSLT_EN,
+			adev->regs + HI_CH_CONF(achan->id));
+		writel(CH_RSLT_CONF_FLUSH_EN,
+			adev->regs + HI_CH_RSLT_CONF(achan->id, adev->ee));
+
+		adm_terminate_all(&adev->channels[i]);
+	}
+
+	clk_disable_unprepare(adev->core_clk);
+	clk_disable_unprepare(adev->iface_clk);
+
+	return 0;
+}
+
+static const struct of_device_id adm_of_match[] = {
+	{ .compatible = "qcom,adm", },
+	{}
+};
+MODULE_DEVICE_TABLE(of, adm_of_match);
+
+static struct platform_driver adm_dma_driver = {
+	.probe = adm_dma_probe,
+	.remove = adm_dma_remove,
+	.driver = {
+		.name = "adm-dma-engine",
+		.of_match_table = adm_of_match,
+	},
+};
+
+module_platform_driver(adm_dma_driver);
+
+MODULE_AUTHOR("Andy Gross <agross@codeaurora.org>");
+MODULE_DESCRIPTION("QCOM ADM DMA engine driver");
+MODULE_LICENSE("GPL v2");